SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
An oscillator circuit and a thermistor, in close proximity to a light bulb, periodically alter the heat output of the bulb by varying the voltage across its filament. Use of this simulator permits checkout tests on pneumographs.
Methods based on the vorticity equation, the adiabatic method, the curvature of the vertical wind profile, and the structure of synoptic waves are used to determine areas of positive vertical motion in the mid-troposphere for a period in each season. Parameters indicative of low-level moisture and conditional instability are areas in which mesoscale systems may be present. The best association between mesoscale and synoptic-scale phenomena was found for a period during December when synoptic-scale systems were well developed. A good association between meso- and synoptic-scale events also was found for a period during March, while the poorest association was found for a June period. Daytime surface heating apparently is an important factor in the formation of mesoscale systems during the summer. It is concluded that the formation of mesoscale phenomena may be determined essentially from synoptic-scale conditions during winter, late fall, and early spring.
General features of the solar chromospheric heating problem, which also apply to many stellar chromospheres, are reviewed. Current theories are discussed, including: heating by short period sound waves; the weak shock theory; and the time-dependent approach.
Neutral composition data obtained by the open-source neutral-mass spectrometer on the polar orbiting Atmosphere Explorer D satellite during the periods October 31 to November 15, 1975, and January 5 to 15, 1976, are used to characterize the response of thermospheric atomic nitrogen densities to geomagnetic activity. These periods provided nearly simultaneous polar and low-latitude data coverage. At low and middle latitudes near dawn and at all latitudes on the dayside, N densities at 400 km appear to vary like those of a species of atomic mass 14: N is observed to increase with increasing geomagnetic activity in a manner similar to that of O. At auroral latitudes near dawn, however, there is a more complex dependence on the amplitude of the disturbance. For substorm-scale activity, N tends to increase during periods of auroral heating but exhibits a sharp temporary decrease afterward. During large storms there is a significant but short-lived increase of N at auroral latitudes. The present results support current models showing that N is produced and transported out of the auroral zone during geomagnetic disturbances.
The feasibility of producing silver or copper alloys containing finely dispersed nickel or iron particles, respectively, by utilizing containerless electromagnetic levitation casting techniques was investigated. A levitation coil was designed to successfully levitate and melt a variety of alloys including Nb-Ge, Cu-Fe, Fe-C, and Ag-Ni. Samples of 70 Cu-30 Fe and 80 Ag-20 Ni (atomic %), prepared by mechanical pressing of the constituent powders, were levitated and heated either to the solid plus liquid range of the alloys or to the fully liquid region. The samples were then solidified by passing helium gas into the bell jar or they were dropped into a quenching oil. The structure of the samples which were heated to the solid plus liquid range consists of uniform distribution of Fe or Ni particle in their respective matrices. A considerable amount of entrapped gas bubbles were contained. Upon heating for longer periods or to higher temperatures, the bubbles coalesced and burst, causing the samples to become fragmented and usually fall out of the coil.
Past thermal models of cometary nuclei have tended to be restricted to hemispherical averages and have ignored many important effects such as surface heat flow, rotation period, or coma opacity. A computer based model called KRC/COM was developed which includes these and many other important effects to give a more accurate physical model of sublimation from icy cometary nuclei. Halley's Comet was used as a test case because of the high interest in the 1986 perihelion passage of that comet.
Mixer blades interrupt airflow for rapid testing of insulating materials. Device for producing periodic blasts of heated air used for rapid testing of flexible insulating materials. Used to compare materials and to select candidates for more detailed testing in wind tunnels.
The bright cool supergiant Alpha Orionis has been monitored spectroscopically and photometrically over the past three years (1984-1986) in the optical and the ultraviolet wavelength regions. A 420-day periodic modulation of the flux is observed in the optical and ultaviolet continua, and in the Mg II line emission cores. Periodic photospheric pulsations are the most likely explanation of these observations. This identification is based on the large amplitude of the variation, the correlation of the continuum and chromospheric fluxes, and the length of the observed period. Pulsation may heat and extend the atmosphere of Alpha Ori and initiate the mass flow from the star.
Boundary layer soundings show the diurnal variation of California coastal stratochumulus. During the period of solar heating, cloud base rises and the cloud layer thins, while the subcloud layer becomes more stable, suggesting some daytime upcoupling of the cloud layer from the surface.
A major surface feature of the Greenland Sea during winter is the frequent eastward extension of sea ice south of 75 deg N and an associated embayment to the north. These features are nominally connected with the East Greenland Current, and both the promontory) and the embayment are readily apparent on climatic ice charts. However, there are significant changes in these features on time-scales as short as a few days. Using a combination of satellite microwave images (SSM/I) of ice cover, meteorological data and in situ velocity, temperature and salinity records, we relate the ice distribution and its changes to the developing structure and circulation of the upper ocean during winter 1988-1989. Our measurements illustrate the preconditioning that leads to convective overturn, which in turn brings warmer water to the surface and results in the rapid disappearance of ice. In particular, the surface was cooled to the freezing point by early December and the salinity then increased through ice formation (about 0.016 m/d) and brine rejection. Once the vertical density gradient was sufficiently eroded, a period of high heat flux (greater than 300 W/sq m) in late January provided enough buoyancy loss to convectively mix the upper water column to at least 200 m. We estimate vertical velocities at about 3 cm/s downward during the initial sinking. The deepening of the thermocline raised surface temperatures by over 1 C resulting in nearly 1.5 x 105 km of ice-melt within two days. Average rates of ice retreat are about 2 km/d southwestward, generally consistent with a wind-driven flow. Comparison of hydrographic surveys from before and after the overturning indicate the fresh water was advected out of the area, possibly to the south and east of our moorings.
NASA's New Horizons mission acquired a large set of images and other data making possible thorough geological analysis of landscapes in the Pluto System. Pluto and Charon exhibit strikingly different surface appearances, despite their similar densities and presumed bulk compositions. Systematic investigation, modelling and mapping revealed that much of Pluto's surface is attributed to surface-atmosphere interactions and the mobilization of volatile ices by insolation. Many mapped valley systems appear to be the consequence of glaciation involving nitrogen ice. Other geological activity requires or required long periods of internal heating, such as Pluto's extensive tectonic fabric. The convection and advection of volatile ices in Sputnik Planitia are thought to be powered by present-day radiogenic heat loss. The prominent mountains at the western margin of Sputnik Planitia, and the strange, multi-km-high mound features to the south, probably composed of H2O, are young geologically as inferred by light cratering and superposition relationships. These multi-km-high mound features might be cryo-volcanoes. Their origin, and what drove their formation so late in Solar System history, is under investigation. East of Sputnik Planitia are large fields of aligned ranks of sharp-crested ridges found only at high altitude that are apparently composed of massive deposits of CH4 ice, referred to as Bladed Terrain. New Horizons found evidence that Bladed Terrain may cover much of Pluto's low latitudes and may have originally formed there as a consequence of Pluto's very high obliquity. Currently Bladed Terrain is undergoing net erosion. This observation, along with evidence for formally more extensive nitrogen glaciation implies that Pluto undergoes significant climate evolution. The dynamic remolding of landscapes by volatile transport seen on Pluto is not unambiguously evident in the mapping of Charon. Charon does, however, display a large resurfaced plain and globally engirdling extensional tectonic network attesting to its early endogenic vigor.
The fuel performance modeling code BISON was used to predict the release of fission products iodine-131 (131I), xenon-133 (133Xe), and krypton-85 (85Kr) from four re-irradiated AGR-3/4 fuel compacts containing tristructural isotropic (TRISO) coated particles during high-temperature isothermal heating tests. The AGR-3/4 fuel compacts were irradiated in the Advanced Test Reactor (ATR) as part of the third and fourth series of planned experiments to support the Advanced Gas Reactor (AGR) Program. They were subsequently stored and re-irradiated in the Neutron Radiography (NRAD) reactor for approximately five days and then stored for another five to eight days before being subjected to isothermal heating tests in the Fuel Accident Condition Simulation (FACS furnace) for 200 to 300 hours at temperatures between 1000°C and 1600°C to evaluate fission product release at elevated temperatures. New nuclide-specific fission product source term models for the three nuclides of interest were developed using the reactor multiphysics code Griffin and implemented into BISON to support this work. The new source term models were incorporated into coupled compact- and particle-scale BISON simulations, which predict spatially- and temporally-resolved radionuclide generation, radioactive decay, transport, and release throughout the entire irradiation history, including the initial ATR irradiation, NRAD re-irradiations, FACS heating tests, and intermediate periods spent in storage. The experimentally measured fission product release from the heating tests were compared to modeling release predictions calculated by BISON to evaluate how well the code compares to experimental results. Overall, the experimental measured and BISON predicted comparative release results varied but generally agreed to within 5 particle equivalents. Comparative release results identified general observations to take into consideration to help refine future models and reduce uncertainties associated with both the measurement results and predictive results. This includes developing new uranium oxycarbide (UCO) specific kernel diffusivities for the three isotopes examined to more accurately reflect the material properties of the fuel form. Deriving new diffusivities will aid in producing a more informed BISON model
HRL Laboratories and General Motors (GM), pursued this effort to increase the efficiency of internal combustion engines (ICEs) by developing and implementing temperature-following thermal barrier coatings (TBCs) to decrease heat loss from the combustion chamber. HRL developed microsphere TBCs based on hollow high-temperature alloy spheres with average diameter of 50 μm and wall thickness ~1 μm (microspheres) that achieve unprecedented low thermal conductivity and heat capacity (10X lower than the state of the art) while offering exceptional environmental and mechanical resistance.> In current ICEs, approximately 29% of the fuel’s energy is lost to the cooling system and about 22% goes into moving the car. By limiting heat losses from the combustion chamber with insulating coatings, fuel energy can be redirected into additional piston work and into the exhaust stream. The additional energy that goes into the exhaust stream can be turned into useful work through the use of an exhaust energy recovery device, such as turbocompounding and/or through driving a turbocharger to increase the power density of the engine allowing downsizing. Insulating coatings for piston crowns have been pursued in the past, but previous materials—typically ceramics—exhibited low thermal conductivity but retained high heat capacity. Such materials reduce heat losses but stabilize at a high surface temperature. The high surface temperature heats the incoming gases, which lowers volumetric efficiency and increases propensity for knock, resulting in degraded engine performance. This program developed an innovative new material that combines low thermal conductivity with low heat capacity. These unique properties allow it to follow rapid changes in gas temperature during each combustion cycle. A metallic microsphere TBC has been demonstrated that exhibits increased surface temperature during the combustion period, resulting in reduced heat transfer losses, while still returning to a low surface temperature during the gas exchange period. A 10X lower thermal conductivity and heat capacity than state-of-the-art thermal barrier coatings has been demonstrated. These unprecedented thermal properties are achieved through the coating architecture, which consists of closed pores on the microscale and exhibits a total porosity of 90% to 95%. By selecting a high-temperature nickel alloy as the coating material, the ductility and strength of metals can be harnessed to achieve much better durability and damage tolerance than brittle ceramic coatings can achieve.
An investigation has been made in the NACA Cleveland icing research tunnel to determine the de-icing effectiveness of an experimental configuration of an Internal electric propeller-blade heater. Two atmospheric Icing conditions and two propeller operating conditions were Investigated, In experiments with unheated blades and with heat applied to the blades both continuously and cyclically. Data are presented to show the effect of propeller speed., ambient air temperature and liquid-water concentration, and the duration of the heat-on and cycle times on the power requirements and de-Icing performance of the blade heaters. The extent of ice-covered area on the blades for various icing ax4 operating conditions has been determined. The largest iced area was obtained at the higher ambient-air temperatures and at low propeller speed. The ohord.wise extent of Icing In practically every case was greater than that covered by blade heaters. Adequate de-icing in the heated area with continuous application of heat was obtained with the power available but a maximum power, input of 1250 watts per blade was insufficient for cyclic de-Icing for the range of conditions investigated. Blade-surface temperature rates of rise of 0.2 to 0.7 F per second were obtained and the minimum cooling period for cyclic de-icing was found to be approximately 2-1/2 times the heating period.
Temperatures are gradually rising at the CSRA, to study this we compared temperature data from the CSRA from the 1970s and the 2010s. We discovered that the 2010 decade was hotter than the 1970s. A heat wave is a period of more than two days when the temperature is abnormally hot. However, heat waves involve more variables than just temperature-high pressure-and low soil moisture are also common. Also, the heat island effect- urban areas tend to be hotter than rural areas-affects the wave. I chose to study two heat waves, June 2015 and May 2019. The high temperatures in the heat wave were related to high pressures and low soil moistures. We compared SRS and Daniel Field and Bush Field Airport temperatures. Daniel Field was in the city and showed higher temperatures during the wave.
We assess a hybrid-energy approach that modifies a steam-turbine power plant to use renewable energy sources (electricity, plus options for geothermal and solar heat), plus fossil fuel (natural gas and coal) and/or waste biomass (e.g., Douglas fir woodchips). Heat storage allows heat to be created during periods of excess energy supply and for that heat to be converted to electricity when demanded. Excess electricity, such as from variable renewable energy (VRE), is used to generate oxygen for oxy-combustion furnaces that create very-hot, high-purity CO 2 that heats granular rock beds in insulated vessels. Cool CO 2 leaving the beds is dried, sent to compressors powered by excess VRE electricity, before being sent by pipeline to geologic CO 2 storage. Very-hot CO 2 transfers high-grade heat from storage to the power plant in a closed loop that returns medium-grade heat back to storage, allowing low- and medium-grade renewable-heat sources to be stacked beneath combustion heat, with all heat sources being converted to electricity at the same (high) thermal efficiency. Reliable, on-demand power may be generated with near-zero CO 2 emissions with fossil fuel and with negative CO 2 emissions with waste biomass. Our analyses show that with fossil fuel, up to 35% of gross power can be derived from renewable sources, while for waste biomass, it can be entirely derived from renewable sources. Because our approach has the potential to ensure that grids have a continuous supply of clean energy and because electricity is only generated once, when demanded, it could serve as an efficient alternative to bulk energy storage.
Precooling is a recognized technique for reducing cooling energy in buildings during peak hours by shifting load to off-peak hours. This technique is particularly effective in buildings with high thermal mass, because of their large thermal energy storage capacity, and in commercial buildings due to their variable electricity pricing based on time-of-use rates. Precooling in residential buildings has been a matter of limited interest in the past because of their low thermal mass and typically uniform electricity pricing rate. While previous studies on precooling primarily focused on cost savings, an important aspect of precooling is the thermal load modulation, which could be very effective in managing peak demand in lightweight residential buildings integrated with thermal energy storage systems. In this study, we examine different precooling strategies to manage the heat gains in lightweight building walls integrated with phase-change materials. We create nine different precooling profiles by controlling the interior temperature, and then evaluate the influence of the precooling profiles on four key building energy performance parameters: total heat gain, peak heat gain, maximum heat gain during peak hours, and time at which peak occurs. To thoroughly understand the fundamental physics, we first consider hypothetical climates and obtain the optimal precooling strategy required to achieve maximum peak shedding and shifting while minimizing the total heat gains. We then extend the model to Baltimore, Maryland, and estimate the benefits of the optimized precooling strategy under real conditions. The optimal precooling strategy proposed in this study can shift the peak heat gain by up to 14 hours, thereby reducing the heat gain during peak period by up to 95%, at the expense of a 23% increase in the total heat gains.
This study examines the use of satellite-derived nowcasted (short-term forecasted) rainfall over 3-hour time periods to gain an equivalent time increment in initializing a nonhydrostatic mesoscale model used for predicting convective rainfall events over the Korean peninsula. Infrared (IR) window measurements from the Japanese Geostationary Meteorological Satellite (GMS) are used to specify latent heating for a spinup period of the model - but in future time -- thus initializing in advance of actual time in the framework of a prediction scenario. The main scientific objective of the study is to investigate the strengths and weaknesses of this approach insofar as data assimilation, in which the nowcasted assimilation data are derived independently of the prognostic model itself. Although there have been various recent improvements in formulating the dynamics, thermodynamics, and microphysics of mesoscale models, as well as computer advances which allow the use of high resolution cloud-resolving grids and explicit latent heating over regional domains, spinup remains at the forefront of unresolved mesoscale modeling problems. In general, non-realistic spinup limits the skill in predicting the spatial-temporal distribution of convection and precipitation, primarily in the early hours of a. forecast, stemming from standard prognostic variables not representing the initial diabatic heating field produced by the ambient convection and cloud fields. The long-term goal of this research is to improve short-range (12-hour) quantitative precipitation forecasting (QPF) over the Korean peninsula through the use of innovative data assimilation methods based on geosynchronous satellite measurements. As a step in th~s direction, a non-standard data assimilation experiment in conjunction with GMS-retrieved nowcasted rainfall information introduced to the mesoscale model is conducted. The 3-hourly precipitation forecast information is assimilated through nudging the associated diabatic heating during the early stages of a forecast period. This procedure is expected to enhance details in the moisture field during model integration, and thus improve spinup performance, assuming the errors in the future time latent heating data ate less than intrinsic model background errors.