SEARCH · Search NASA

Results for “Planetary entry missions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS2016

Mars Cube One (MarCO) Shifting the Paradigm in Relay Deep Space Operations

A very significant challenge in the planetary mission design and operations is communications with ground control teams during critical events and highly risky maneuvers. These include entry, descent, and landing (EDL) and orbit insertion, which should not be carried out in the blind. Although vast planetary distances and long round-trip light times disallow real-time intervention from controllers, acquiring the relevant event performance parameters in near real-time can be imperative for determining the corrective actions needed immediately following or, in the case of significant anomalies, aid in the diagnostic analysis. During several previous Mars missions landing events, and the Huygens probe landing on Titan, the communications strategy relied on proximity links to planetary orbiters, which then relayed the data to the Deep Space Network (DSN). In addition, attempts were successfully made in parallel to receive the signal carrier directly at Earth often using large radio telescopes when the wavelength was outside the DSN’s reception bands. This Direct-to-Earth (DTE) back-up method was only possible due to special techniques utilizing the DSN’s open-loop Radio Science Receivers. In every case, it was very challenging since the link budget of a landing vehicles were designed for proximity orbiter relays and not for distances across the solar system. A new method is introduced since not all future missions can rely on the presence of pre-existing orbiters at their planetary targets to relay their critical data ad, furthermore, most missions would not likely have the resources to implement a reliable DTE link at acceptable data rates, bypassing a need for a relay asset. With the advent CubeSat form-factor spacecraft, one or more, for added reliability, CubeSats can be launched with the primary mission, travel to the target, and be positioned to view the critical event, such as EDL, and carry out real-time relay of the data to the DSN at higher rates. CubeSats have flown in the Earth environment but never flown or been operated in deep space or planetary environment so careful design as well as flight experience are needed. The relay function requires the development of radio and antenna systems to meet challenging specifications. After initial technical demonstration of the concept and operational experience, the cost can decrease as systems become more standardized with increased reliability. This paper describes the invention of the “carry your own relay” concept and the formulation of the mission likely to be the first planetary CubeSat mission called Mars Cube One (MarCO). It also describes the operational concept of relay small spacecraft and their role reducing mission risk as well as overall mission cost.

Asmar, Sami↗

NASA NTRSDate not supplied

AERACEPT (Aerosol Rapid Analysis Combined Entry Probe/sonde Technology): Enabling Technology for Planetary Atmospheric Science Probes

Aerosols –clouds, hazes, and dusts –are a key part of planetary mass and energy balance, but difficult to study remotely. Current technology limits in situ measurements to once-in-a-lifetime flagship missions, which is not enough to characterize such highly dynamic systems. AERACEPT (AErosol Rapid Analysis Combined Entry Probe/sonde Technology) is an early-stage technology allowing asingle aeroshell body toact as both anentry vehicle and aerosol-samplingpassivedescent sonde, using the aeroshell’sown velocityto drive aerosol capture and separationthrough a series of embedded inlets.It takes advantage ofrecently developed thermal protection materials (3D-CC and 3MDCP)in combination withheritage aerosol sampling technologies fromboth planetary and airborne science (high-speed inlets and particle separation). By eliminating the need for heat shield separation, deployable parachutes, ordescent control, AERACEPT reducesthe mass, volume, and complexity ofplanetary aerosol sampling. Verifying AERACEPT’s performance involves modeling interdependencies between the size and geometry of the sampling inlets, the material response of the hypersonic phase of entry, the thermal conditions throughout the probe’s descent, the subsonic flow and particle sampling efficiency, the needed amount of sample, andthe cadence at which the sample can be analyzed. AERACEPT’s current predictions, using the Nephele Venus cloud mission concept (sampling between 63km to 39km, all subsonic) indicates AERACEPT can obtain >20 μL of particle material (roughly 10x the limit of detection) from droplets larger than 0.2 μm, with sample heating limited to <15 K above ambient. Validation testing for the thermal material response model has recently been performed at the UIUC Plasmatron facility, and for the flow and particle capture models is planned for this fall at the Ames Fluid Mechanics Laboratory.

AERACEPT↗

NASA NTRS2019

New Method for Systems and Cost Analysis of Human Mars Entry Vehicles

Cost is one of the biggest obstacles to sending humans to Mars. However, spacecraft costs are typically not estimated until after the preliminary vehicle and mission concepts have been designed. By automating the cost estimation process, the effect of any change in vehicle or mission design on the mission cost can be determined more efficiently. This paper describes an extension to the tool SAPE (Systems Analysis for Planetary Entry, Descent, and Landing). This extension integrates the cost modeling software SEER-H (System Estimation and Evaluation of Resources-Hardware) with a number of systems analysis tools. This new method is used to analyze several trade spaces of a HIAD (Hypersonic Inflatable Aerodynamic Decelerator) entry vehicle for human Mars missions. Key findings include quantifying the impacts of ballistic coefficient, main engine specific impulse, and thrust-to-weight ratio on the overall cost of the vehicle, and how the payload per lander and number of landers affects the cost of a campaign to Mars.

Friz, Paul D.↗

NASA NTRS1997

Rarefied Flows of Planetary Entry Capsules

The impact of rarefaction on entry capsules and spacecraft aerothermodynamics is emphasized for various aeroassist missions. The capability of the direct simulation Monte Carlo (DSMC) method to simulate such flows is demonstrated through examples of validation studies and applications. Several space flight projects and ground-based experiments are reviewed for which rarefaction effects have significant effect on spacecraft performance or experimental measurements. This review clearly demonstrates the significant role that the DSMC method plays in characterizing such flows.

James N Moss↗

NASA NTRSDate not supplied

Parametric Cost Modeling of a Mid-Lift-to-Drag Ratio Vehicle for Human Mars Entry, Descent, and Landing

Cost is one of the biggest obstacles to sending humans to Mars. However, spacecraft costs are typically estimated after the preliminary vehicle and mission concepts have been designed. By automating the cost estimation process, the effect of any change in vehicle or mission design on the mission cost can be determined more rapidly. This paper uses the tool SAPE-C (Systems Analysis for Planetary Entry, Descent, and Landing-Cost). SAPE-C integrates the cost modeling software SEER-H (System Estimation and Evaluation of Resources-Hardware) with a number of systems analysis tools and enables large design tradespace exploration early in the design process. SAPE-C is used to analyze several tradespaces of the Mid-Lift-to-Drag ratio rigid entry vehicle for human Mars missions. Key findings include quantifying the impacts of payload, vehicle length, and main engine specific impulse on the overall cost of the vehicle, and how the payload per lander and number of landers affects the cost of a campaign to Mars.

Mid L/D↗

NASA NTRSDate not supplied

Parametric Cost Modeling of a Mid-Lift-to-Drag Ratio Vehicle for Human Mars Entry, Descent, and Landing

Paul D Friz↗

NASA NTRSDate not supplied

Parametric Cost Modeling of a Mid-Lift-to-Drag Ratio Vehicle for Human Mars Entry, Descent, and Landing

Paul D Friz↗

NASA NTRSDate not supplied

In Situ Small Spacecraft Missions Utilizing Heatshield for Extreme Entry Environments Technology

There is considerable interest in utilizing Small Spacecraft beyond low Earth orbit. In November of 2018, successful data relay operations of the MarCO CubeSats during the entry, descent, and landing (EDL) of the Mars InSight mission showed the viability of using CubeSats for interplanetary missions. Additional testament to the promise of Small Spacecraft class rideshare missions is the upcoming Artemis-1 flight test that will launch thirteen 6U CubeSats, as well as the establishment of NASA’s SIMPLEx program which will conduct stand-alone planetary science missions that launch with a primary payload. It is anticipated that continued innovations in Small Spacecraft capabilities combined with small EDL systems will expand the range of potential missions to allow for in situ investigations. Recently, NASA invested in the development of a new, efficient and capable ablative thermal protection system (TPS), utilizing 3-D Weaving. The new dual layer TPS, Heatshield for Extreme Entry Environment Technology (HEEET), is tailorable, scalable, robust, mass efficient and capable of supporting in situ missions across the solar system. Combining the HEEET entry system with innovative Small Spacecraft technology will substantially expand the range of Small Spacecraft mission applications by offering the capability for high speed entry or aerocapture at destinations with atmospheres. This paper will describe the HEEET aeroshell system and highlight various mission concepts including a dual technology demonstration mission that is under development and other concepts to deliver instruments for planetary science.

Small Spacecraft↗

NASA NTRS1973

Developing a technology base in planetary entry aerothermodynamics

The long-range objectives of the entry technology program are to insure that an adequate technology base for a great variety of mission options exists. Consideration has been given to the entry of vehicles into the atmospheres of all the planets with the exception of Pluto. The experimental facilities for the studies are discussed, giving attention to shock tubes, the planetary entry radiation facility, ballistic ranges, the expansion tube, and arc jet facilities. Flight experiments are considered along with computational analyses and engineering approximations.

Olstad, W. B.↗

NASA NTRS2013

Comparison of Failure Modes in 2-D and 3-D Woven Carbon Phenolic Systems

NASA Ames Research Center is developing Woven Thermal Protection System (WTPS) materials as a new class of heatshields for entry vehicles (Stackpoole). Currently, there are few options for ablative entry heatshield materials, none of which is ideally suited to the planetary probe missions currently of interest to NASA. While carbon phenolic was successfully used for the missions Pioneer Venus and Galileo (to Jupiter), the heritage constituents are no longer available. An alternate carbon phenolic would need to be qualified for probe missions, which is most efficient at heat fluxes greater than those currently of interest. Additional TPS materials such as Avcoat and PICA are not sufficiently robust for the heat fluxes required. As a result, there is a large TPS gap between the materials efficient at very high conditions (carbon phenolic) and those that are effective at low-moderate conditions (all others). Development of 3D Woven TPS is intended to fill this gap, targeting mid-density weaves that could with withstand mid-range heat fluxes between 1100 W/sq cm and 8000 W/sq cm (Venkatapathy (2012). Preliminary experimental studies have been performed to show the feasibility of WTPS as a future mid-range TPS material. One study performed in the mARC Jet Facility at NASA Ames Research Center characterized the performance of a 3D Woven TPS sample and compared it to 2D carbon phenolic samples at ply angles of 0deg, 23.5deg, and 90deg. Each sample contained similar compositions of phenolic and carbon fiber volume fractions for experimental consistency. The goal of this study was to compare the performance of the TPS materials by evaluating resulting recession and failure modes. After exposing both samples to similar heat flux and pressure conditions, the 2D carbon phenolic laminate was shown to experience significant delamination between layers and further pocketing underneath separated layers. The 3D Woven TPS sample did not experience the delamination or pocketing failure modes because z-fibers in the through-thickness direction provided extra reinforcement to hold material layers together. Therefore, the benefit of using a 3D weave architecture was shown to alleviate failure modes experienced by a 2D laminate sample of similar material composition. In summary this poster reviews the thermal response performance comparisons drawn between a 3D Woven TPS sample and 2D Carbon Phenolic samples after performing rigorous heating experiments in the mARC facility at NASA Ames. Although the mARC Facility is still in its developmental stages, researchers expect similar trends in failure modes observed from large scale arc jet facilities. This work helps demonstrate the viability of 3D Woven TPSs as a new TPS option for future atmospheric entry missions.

Rossman, Grant A.↗

NASA NTRS2005

Magnetohydrodynamic Power Generation in the Laboratory Simulated Martian Entry Plasma

This paper addresses the magnetohydrodynamic (MHD) conversion of the energy released during the planetary entry phase of an interplanetary vehicle trajectory. The effect of MHD conversion is multi-fold. It reduces and redirects heat transferred to the vehicle, and regenerates the dissipated energy in reusable and transportable form. A vehicle on an interplanetary mission carries about 10,000 kWh of kinetic energy per ton of its mass. This energy is dissipated into heat during the planetary atmospheric entry phase. For instance, the kinetic energy of Mars Pathfinder was about 4220 kWh. Based on the loss in velocity, Mars Pathfinder lost about 92.5% of that energy during the plasma-sustaining entry phase that is approximately 3900 kWh. An ideal MHD generator, distributed over the probe surface of Mars Pathfinder could convert more than 2000 kWh of this energy loss into electrical energy, which correspond to more than 50% of the kinetic energy loss. That means that the heat transferred to the probe surface can be reduced by at least 50% if the converted energy is adequately stored, or re-radiated, or directly used. Therefore, MHD conversion could act not only as the power generating, but also as the cooling process. In this paper we describe results of preliminary experiments with light and microwave emitters powered by model magnetohydrodynamic generators and discuss method for direct use of converted energy.

Vuskovic, L.↗

NASA NTRS2005

The Next Generation of Planetary Atmospheric Probes

Entry probes provide useful insights into the structures of planetary atmospheres, but give only one-dimensional pictures of complex four-dimensional systems that vary on all temporal and spatial scales. This makes the interpretation of the results quite challenging, especially as regards atmospheric dynamics. Here is a planetary meteorologist's vision of what the next generation of atmospheric entry probe missions should be: Dedicated sounding instruments get most of the required data from orbit. Relatively simple and inexpensive entry probes are released from the orbiter, with low entry velocities, to establish ground truth, to clarify the vertical structure, and for adaptive observations to enhance the dataset in preparation for sensitive operations. The data are assimilated onboard in real time. The products, being immediately available, are of immense benefit for scientific and operational purposes (aerobraking, aerocapture, accurate payload delivery via glider, ballooning missions, weather forecasts, etc.).

Houben, Howard↗

NASA NTRS2013

The Status of Spacecraft Bus and Platform Technology Development under the NASA In-Space Propulsion Technology Program

NASA's In-Space Propulsion Technology (ISPT) program has been developing technologies for lowering the cost of planetary science missions. The technology areas include electric propulsion technologies, spacecraft bus technologies, entry vehicle technologies, and design tools for systems analysis and mission trajectories. The electric propulsion technologies include critical components of both gridded and non-gridded ion propulsion systems. The spacecraft bus technologies under development include an ultra-lightweight tank (ULTT) and advanced xenon feed system (AXFS). The entry vehicle technologies include the development of a multi-mission entry vehicle, mission design tools and aerocapture. The design tools under development include system analysis tools and mission trajectory design tools.

Anderson, David↗

NASA NTRS2013

Products from NASA's In-Space Propulsion Program Applicable to Low-Cost Planetary Missions

NASAs In-Space Propulsion Technology (ISPT) program has been developing technologies for lowering the cost of planetary science missions. The technology areas include electric propulsion technologies, spacecraft bus technologies, entry vehicle technologies, and design tools for systems analysis and mission trajectories. The electric propulsion technologies include critical components of both gridded and non-gridded ion propulsion systems. The spacecraft bus technologies under development include an ultra-lightweight tank (ULTT) and advanced xenon feed system (AXFS). The entry vehicle technologies include the development of a multi-mission entry vehicle, mission design tools and aerocapture. The design tools under development include system analysis tools and mission trajectory design tools.

Anderson, David↗

NASA NTRS2014

Flexible Polyimide Aerogel Cross-linked by Poly(maleic Anhydride-alt-alkylene)

Aerogels are potential materials for aerospace applications due to their lower thermal conductivity, lighter weight, and low dielectric constant. However, silica aerogels are restricted due to their inherent fragility, hygroscopic nature, and poor mechanical properties, especially in extreme aerospace environments. In order to fit the needs of aerospace applications, developing new thermal insulation materials that are flexible, and moisture resistant is needed. To this end, we fabricated a series of polyimide aerogels crosslinked with different poly(maleic anhydride-alt-alkylene)s as seen in Scheme 1. The polyimide oligomers were made with 3,3,4,4-biphenyltetracarboxylic dianhydride (BPDA), and different diamines or diamine combinations. The resulting aerogels have low density (0.06 gcm3 to 0.16 gcm3) and high surface area (240-440 m2g). The effect of the different backbone structures on density, shrinkage, porosity, surface area, mechanical properties, moisture resistance and thermal properties will be discussed. These novel polyalkylene-imide aerogels may be potential candidates for applications such as space suit insulation for planetary surface missions, insulation for inflatable structures for habitats, inflatable aerodynamic decelerators for entry, descent and landing (EDL) operations, and cryotank insulation for advance space propulsion systems. Scheme 1. Network of polyimide aerogels crosslinked with deifferent poly(maleic anhydride).

cross-link↗

NASA NTRS2014

Synthesis, Processing, and Characterization of Inorganic-Organic Hybrid Cross-Linked Silica, Organic Polyimide, and Inorganic Aluminosilicate Aerogels

As aerospace applications become ever more demanding, novel insulation materials with lower thermal conductivity, lighter weight and higher use temperature are required to fit the aerospace application needs. Having nanopores and high porosity, aerogels are superior thermal insulators, among other things. The use of silica aerogels in general is quite restricted due to their inherent fragility, hygroscopic nature, and poor mechanical properties, especially in extereme aerospace environments. Our research goal is to develop aerogels with better mechanical and environmental stability for a variety of aeronautic and space applications including space suit insulation for planetary surface missions, insulation for inflatable structures for habitats, inflatable aerodynamic decelerators for entry, descent and landing (EDL) operations, and cryotank insulation for advance space propulsion systems. Different type of aerogels including organic-inorganic polymer reinforced (hybrid) silica-based aerogels, polyimide aerogels and inorganic aluminosilicate aerogels have been developed and examined.

Insulation materials↗

NASA NTRSDate not supplied

Pterodactyl: Non-propulsive Control Systems for Future Planetary Missions

This white paper presents an assessment of control systems as it relates to state-of-the-art hypersonic entry vehicles and addresses technological advances that enable new control systems for future hypersonic entry vehicles. Advancements in deployable entry vehicle (DEV) technology, entry guidance, woven thermal protection systems, and affordable launch services make it possible to conceive of entry vehicles that optimize entry loads, maneuverability, usable payload mass and volume, and operational costs. NASA’s Space Technology Mission Directorate (STMD) is currently funding the authors on a project, Pterodactyl, that is using on-the-fly trajectory design and integrated software and hardware development to investigate non-propulsive entry control systems for precision targeting of mechanical DEVs. The authors recently reported key findings of these control systems for an asymmetric DEV to track bank commands for a lunar sample return entry.

Sarah D'Souza↗

NASA NTRS2017

Overview of SPRITE: Saturn Probe Interior and aTmosphere Explorer Concept

The Saturn PRobe Interior and aTmosphere Explorer (SPRITE) mission concept targets high-priority Planetary Science Decadal Survey science objectives. This mission concept would deliver the SPRITE entry probe into the Saturn atmosphere to obtain in situ measurements of elemental abundances and isotopic ratios, which would help distinguish the role Saturn played in the solar system formation and co-evolution of other planets. An Atmospheric Structure Investigation sensor package on the entry probe would provide in situ measurements of the pressure/temperature and wind structure below the cloud-tops, and a Quadrupole Mass Spectrometer and Tunable Laser Spectrometer suite would determine the composition of Saturn’s atmosphere. The SPRITE mission concept described in this paper uses a solar-powered carrier-relay spacecraft to deliver the battery-powered entry probe to Saturn after a 10-year Venus-Earth-Earth gravity-assist trajectory, and then relays the probe data back to Earth during the carrier-relay spacecraft Saturn flyby. A high-heritage design approach is implemented for the flight elements to minimize technical risk and enable successful return of this high-value science data.

Cuddy, Cavan↗