Search NASA⌕ Search

SEARCH · Search NASA

Results for “Pt catalysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Design improvements for a recirculating reactor: Enhanced temperature measurement and sample-isolated reactivity in steady-state kinetic studies

Building upon a previous recirculating reactor design [S.A. Tenney, K. Xie, J.R. Monnier, A. Rodriguez, R.P. Galhenage, S. Audrey, D.A. Chen, Rev. Sci. Instrum. 84, 104101 (2013)], we present significant improvements that address key limitations in steady-state kinetic measurements for heterogeneous catalysis. The enhanced reactor design features direct sample heating with a focused IR lamp and temperature measurement in direct contact with the sample, enabling more accurate temperature control and improved kinetic analysis. A critical advancement is the isolation of sample reactivity from reactor wall contributions, ensuring that only the sample contributes to measured reaction rates. This was a limitation in earlier designs where the entire reactor contributed to the observed reactivity. The system incorporates a bypass flow cell for direct comparison with powder catalysts under identical conditions using a standard plug-flow reactor configuration. We demonstrate these capabilities through CO oxidation experiments on Pt(111) single crystals and graphene-passivated Pt(111), highlighting the system's ability to differentiate catalytic activity in model systems and directly compare them with high surface area powder catalysts. This reactor is particularly suited for thin films and low surface area catalysts that are not effectively evaluated in traditional flow reactors, especially for samples with low numbers of active sites or slow reaction rates.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Towards improved conversion of wet waste to jet fuel with atomic layer deposition-coated hydrodeoxygenation catalysts

The conversion of wet waste-derived volatile fatty acids into jet fuel-range hydrocarbons is a promising route for increasing the production of sustainable aviation fuel; however, the cost and moderate alkane selectivity of Pt-based hydrodeoxygenation catalysts present challenges for commercialization. Here, to address this, we used atomic layer deposition to apply TiO 2 overcoats to Pt/Al 2 O 3 catalysts and create new interface sites that exhibited 8 times higher site time yield of the desirable n-alkane product than uncoated catalyst. Through TPR/TPD, XPS, CO DRIFTS, and DFT calculations, we found that the increased selectivity of the ALD-coated catalyst was due to the creation of O vacancies at the Pt-TiO 2 interface under reducing conditions, resulting in new Ti 3+ acid sites near the active metal. Maximum conversion and alkane selectivity during HDO was achieved with an ALD-coated 0.5% wt Pt catalyst, indicating that TiO 2 ALD can be used to maximize the utility of precious-metal catalysts.

09 BIOMASS FUELS↗
DOE OSTI2025

Toward an Understanding of Linear Scaling Relations through Energy Decomposition Analysis

The discovery of linear scaling relations has fundamentally changed the field of heterogeneous catalysis. The scaling relations have been rationalized based on the d-band theory, specifically a separation of sp and d electron contributions to adsorption energies. Within the framework of energy decomposition analysis, a full understanding of such a separation would require one to further break down the adsorption energy into distinct energy components such as electrostatics, polarization, charge transfer, and van der Waals interactions, and to examine the sp and d contributions to each of them. As a step in this direction, we analyzed the interaction energy between CH x (x = 1–4) adsorbates and fcc(100) transition metal surfaces (M = Cu, Ag, Au, Rh, and Pt), with the surfaces represented both as slabs in plane-wave density functional theory (pw-DFT) calculations and as atomic clusters in atomic-orbital basis density functional theory (ao-DFT) calculations. Through an absolutely localized molecular orbital (ALMO) based energy decomposition analysis of the ao-DFT adsorption energy, each of the interaction energy components (electrostatics, polarization, van der Waals, and charge transfer) was found to follow its own scaling relations, with an intricate interplay among these energy components yielding the overall scaling relations for the total adsorption energies. Using the recently introduced ALMO-based polarization and charge-transfer analysis schemes, we further dissected polarization into metal surface and adsorbate contributions, and charge transfer into metal → adsorbate and adsorbate → metal contributions. The contributions from the sp and d electrons of the metal to these terms were further quantified, and the dominant role of the metal d electrons was reaffirmed. These results shed light on how CHx adsorbates interact with metal surfaces and further reveal the physical origin of the scaling relations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Carbon nanotubes decorated with Pt as a viable electrocatalyst system using electrochemical atomic layer deposition

Surface limited redox replacement (SLRR) is an electrochemical deposition method designed to deposit metal thin films, typically onto other metals, that are mere monolayers in thickness, where such low dimensions allows catalyst-support interactions to affect catalyst efficiency. Here we explore the growth of Pt, using iterative Cu-mediated SLRR cycles, directly onto carbon nanotubes (CNTs) which are potentially good candidates as electrocatalyst supports due to their electrical conductivity and chemical resistance. Here scanning electron microscope images showed that Pt grew as nanoparticles, and hydrogen underpotential deposition from cyclic voltammetry showed that the active surface area approached an asymptotic value around eight iterations. Catalytic activity, measured using the oxygen reduction reaction, reached a maximum at ten iterations. Both are shown to be influenced by the growth mode, but electrochemical modeling indicates that the trend in activity is also due to a change in activation energy, possibly due to changes in Pt electronic structure due to interactions with the CNTs. Durability cycling showed a greater than 85% retention of surface area for the first 10,000 cycles of accelerated stress testing but decayed steadily to about 50% after 30,000 cycles. This performance may be related to the phenomenon that limits surface area growth.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Surface oxygenation of multicomponent nanoparticles toward active and stable oxidation catalysts

Abstract The need for active and stable oxidation catalysts is driven by the demands in production of valuable chemicals, remediation of hydrocarbon pollutants and energy sustainability. Traditional approaches focus on oxygen-activating oxides as support which provides the oxygen activation at the catalyst-support peripheral interface. Here we report a new approach to oxidation catalysts for total oxidation of hydrocarbons (e.g., propane) by surface oxygenation of platinum (Pt)-alloyed multicomponent nanoparticles (e.g., platinum-nickel cobalt (Pt–NiCo)). The in-situ/operando time-resolved studies, including high-energy synchrotron X-ray diffraction and diffuse reflectance infrared Fourier transform spectroscopy, demonstrate the formation of oxygenated Pt–NiOCoO surface layer and disordered ternary alloy core. The results reveal largely-irregular oscillatory kinetics associated with the dynamic lattice expansion/shrinking, ordering/disordering, and formation of surface-oxygenated sites and intermediates. The catalytic synergy is responsible for reduction of the oxidation temperature by ~100 °C and the high stability under 800 °C hydrothermal aging in comparison with Pt, and may represent a paradigm shift in the design of self-supported catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Higher loadings of Pt single atoms and clusters over reducible metal oxides: application to C–O bond activation

We develop higher loadings of isolated noble metal atoms and clusters on a mildly reducible metal oxide. Here we demonstrate the approach for Pt supported on TiO 2 and confirmed it by XRD, AC-HAADF-STEM, CO-FTIR, XAS, and XPS. Density functional theory calculations rationalize the experimental stability and the IR shifts using mixtures of CH 3 I and CO. The redispersed catalysts are thermally stable in inert gas or H 2 and afford enhanced selectivity and activity in hydrodeoxygenation reactions compared to metal nanoparticles by creating surface oxygen vacancies that promote C–O cleavage without side reactions. Higher metal loadings, e.g., 1%Pt/TiO 2 , on the oxide surface profoundly increase the activity of the bare oxide catalyst tenfold compared to ultra-low loadings typically used for single atom catalysis.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tunable amorphous carbon films formed on ultralow wear, Pt–Au alloys

The mechanocatalytic formation of carbonaceous films at the interface between sliding metallic contacts is simultaneously advantageous for reducing friction and adhesion in several tribological applications and detrimental for electrical contacts as they can induce device failure by increasing the contact resistance. Yet, remarkably little is still known about the chemistry, structural and mechanical properties, and tunability of these interfacial layers. In this study, we performed contact pressure-dependent tribological experiments in dry nitrogen containing trace organics on four, nanocrystalline Pt–Au alloys ([Au] from 0 at.% to 10 at.%) – a promising class of alloys for ultralow wear and electrical contact applications. The ex-situ, multi-technique characterization results did not only provide insights into the chemical nature and mechanical behavior of the mechanocatalytic, carbon-rich films formed on Pt–Au surfaces, but also revealed the interplay between catalytic and mechanochemical tribofilm formation controlled by the composition-dependent electronic structure of the Pt–Au substrate and the applied contact pressure. The results of this work provide guidelines for tailoring nanocrystalline alloys to control their mechanocatalytic activity on the basis of variations of the alloy mechanical properties and element's electronic structure with the alloy stoichiometry.

AFM↗
DOE OSTI2023

Memory-dictated dynamics of single-atom Pt on CeO2 for CO oxidation

Abstract Single atoms of platinum group metals on CeO 2 represent a potential approach to lower precious metal requirements for automobile exhaust treatment catalysts. Here we show the dynamic evolution of two types of single-atom Pt (Pt 1 ) on CeO 2 , i.e., adsorbed Pt 1 in Pt/CeO 2 and square planar Pt 1 in Pt AT CeO 2 , fabricated at 500 °C and by atom-trapping method at 800 °C, respectively. Adsorbed Pt 1 in Pt/CeO 2 is mobile with the in situ formation of few-atom Pt clusters during CO oxidation, contributing to high reactivity with near-zero reaction order in CO. In contrast, square planar Pt 1 in Pt AT CeO 2 is strongly anchored to the support during CO oxidation leading to relatively low reactivity with a positive reaction order in CO. Reduction of both Pt/CeO 2 and Pt AT CeO 2 in CO transforms Pt 1 to Pt nanoparticles. However, both catalysts retain the memory of their initial Pt 1 state after reoxidative treatments, which illustrates the importance of the initial single-atom structure in practical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Graph theory approach to determine configurations of multidentate and high coverage adsorbates for heterogeneous catalysis

Abstract Heterogeneous catalysts constitute a crucial component of many industrial processes, and to gain an understanding of the atomic-scale features of such catalysts, ab initio density functional theory is widely employed. Recently, growing computational power has permitted the extension of such studies to complex reaction networks involving either high adsorbate coverages or multidentate adsorbates, which bind to the surface through multiple atoms. Describing all possible adsorbate configurations for such systems, however, is often not possible based on chemical intuition alone. To systematically treat such complexities, we present a generalized Python-based graph theory approach to convert atomic scale models into undirected graph representations. These representations, when combined with workflows such as evolutionary algorithms, can systematically generate high coverage adsorbate models and classify unique minimum energy multidentate adsorbate configurations for surfaces of low symmetry, including multi-elemental alloy surfaces, steps, and kinks. Two case studies are presented which demonstrate these capabilities; first, an analysis of a coverage-dependent phase diagram of absorbate NO on the Pt 3 Sn(111) terrace surface, and second, an investigation of adsorption energies, together with identifying unique minimum energy configurations, for the reaction intermediate propyne (CHCCH 3 *) adsorbed on a PdIn(021) step surface. The evolutionary algorithm approach reproduces high coverage configurations of NO on Pt 3 Sn(111) using only 15% of the number of simulations required for a brute force approach. Furthermore, the screening of potentially hundreds of multidentate adsorbates is shown to be possible without human intervention. The strategy presented is quite general and can be applied to a spectrum of complex atomic systems.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Reconciling Work Functions and Adsorption Enthalpies for Implicit Solvent Models: A Pt (111)/Water Interface Case Study

Implicit solvent models are a computationally efficient method of representing solid/liquid interfaces prevalent in electrocatalysis, energy storage, and materials science. However, electronic structure changes induced at the metallic surface by the dielectric continuum are not fully understood. To address this, we perform DFT calculations for the Pt(111)/water interface, in order to compare Poisson–Boltzmann continuum solvation methods with ab initio molecular dynamics (AIMD) simulations of explicit solvent. We show that the implicit solvent cavity can be parametrized in terms of the electric dipole moment change at the equilibrated explicit Pt/water interface to obtain the potential of zero charge (PZC). We also compare the accuracy of aqueous enthalpies of adsorption of phenol on Pt(111) using geometry and charge density based dielectric cavitation methods. The ability to parametrize the cavity according to individual atoms, as afforded in the geometry based approach, is key to obtaining accurate enthalpy changes of adsorption under aqueous conditions. Additionally, we show that the electronic structure changes induced by explicit solvent and our proposed implicit solvent parametrization scheme yield comparable density difference profiles and d-band projected density of states. We therefore demonstrate the capability of implicit solvent approaches to capture both the energetics of adsorption processes and the main electronic effects of aqueous solvent on the metallic surface. Therefore, this work provides a scheme for computationally efficient simulations of interfacial processes for applications in areas such as heterogeneous catalysis and electrochemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Theoretical investigation of surface chemical reactivity of compositionally disordered multi-metallic alloys

Alloys are widely used in both academic and industrial research as heterogeneous catalysts for accelerating technologically important reactions ranging from hydrocarbon reforming, selective hydrogenation, to electrochemical reactions involving hydrogen and oxygen that are fundamental and indispensable to a sustainable future energy infrastructure. Most basic catalysis research has been limited to combinations of two elements that are usually ordered in some manner at the nanoscale because doing so allows observable results to be easily rationalized. It however leaves a huge material space consisting of multi metallic, compositionally disordered alloys unexplored. This research demonstrates a viable theoretical approach combining different types of first principles calculations (including Green’s function-based Korringa–Kohn–Rostoker coherent potential approximation (KKR–CPA) and planewave-based density functional theory) to enable the surface chemical reactivity of compositionally complex alloy surfaces to be investigated. We demonstrate the approach by investigating hydrogen adsorption and evolution on two types of compositionally disordered alloys: a quaternary CoCrFeNi high-entropy alloy, and binary Pt-3d base metal alloys.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Kinetics and Reaction Mechanisms of Acetic Acid Hydrodeoxygenation over Pt and Pt–Mo Catalysts

In this work, kinetic measurements for silica-supported Pt and Pt-Mo catalysts were collected in vapor-phase acetic acid hydrodeoxygenation by varying the hydrogen partial pressure between 18 and 72 kPa and acetic acid partial pressure between 7 and 18 kPa at 423-473 K. At all testing conditions, the Pt-Mo catalyst was more active and selective. In addition, the apparent activation energy for Pt-Mo of 76±3 kJ/mol was lower than that of 84±4 kJ/mol for Pt. The apparent reaction orders were also different. The order in hydrogen of 0.8±0.1 for Pt-Mo changed to zero at higher hydrogen partial pressures while that for Pt remained constant at 0.6±0.1. A near-zero order in acetic acid for Pt-Mo changed to -2.1 at higher acetic acid pressures while that for Pt remained constant at -2.9±0.3. These differences in reaction kinetics as well as in selectivity trends with changes in temperature and feed composition indicated a change in the reaction mechanism for Pt-Mo. The catalysts were characterized with hydrogen temperature programmed desorption, oxygen temperature programmed oxidation and transmission electron microscopy with energy-dispersed X-ray spectroscopy elemental mapping. Mo was present in the form of subnanometer-size clusters on the surface of Pt nanoparticles. Both Pt and Pt-Mo catalysts were stable under the reaction conditions for 10 h, and the size and structure of Pt and Pt-Mo particles remained mostly unchanged, without coke accumulation. Density functional theory calculations show that surface acetate is not a major reaction intermediate on both Pt and Pt-Mo and, instead, C-OH bond splitting with the formation of acetyl is the first reaction step in hydrodeoxygenation. The activation energy for this step is dramatically lower on Pt-Mo. Furthermore, the activity of acetyl on Pt-Mo is different. Unlike on pure Pt, the reaction of C-O bond splitting becomes exothermic with a lower activation energy on Pt-Mo, and the reaction of C-C bond splitting, in contrast, becomes endothermic with a higher activation energy, explaining the experimentally observed higher activities and selectivities of Pt-Mo. In addition, the calculations demonstrate that a pair of Pt-Mo surface atoms acts as a single active site where Mo serves as a preferential binding anchor for O atoms. The presence of Mo atoms changes the structure and energy of adsorbed and reacting surface species.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Dynamic structure of active sites in ceria-supported Pt catalysts for the water gas shift reaction

Oxide-supported noble metal catalysts have been extensively studied for decades for the water gas shift (WGS) reaction, a catalytic transformation central to a host of large volume processes that variously utilize or produce hydrogen. There remains considerable uncertainty as to how the specific features of the active metal-support interfacial bonding—perhaps most importantly the temporal dynamic changes occurring therein—serve to enable high activity and selectivity. Here we report the dynamic characteristics of a Pt/CeO 2 system at the atomic level for the WGS reaction and specifically reveal the synergistic effects of metal-support bonding at the perimeter region. We find that the perimeter Pt 0 -O vacancy -Ce 3+ sites are formed in the active structure, transformed at working temperatures and their appearance regulates the adsorbate behaviors. We find that the dynamic nature of this site is a key mechanistic step for the WGS reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Effects of water on the kinetics of acetone hydrogenation over Pt and Ru catalysts

We employed an approach combining reaction kinetics measurements at steady state conditions, electronic structure calculations employing density functional theory, and microkinetic modeling for acetone hydrogenation to provide insights into the effects of water on metal catalyst surfaces for the hydrogenation of oxygenates over a wide range of reaction conditions. Elucidation of the repulsive interactions due to adsorbed water molecules at various reaction conditions provides a basis to formulate rate expressions for heterogeneous catalytic processes of biomass oxygenates. Reaction kinetics experiments were carried out at partial pressures of H 2 , acetone, water and helium in the range of 0.51-0.79, 0.02-0.13, 0.08-0.23, 0-0.28 atm, respectively. We show that the addition of water enhances the hydrogenation rate at 353 K and 1 atm on oxophilic metal catalysts such as Ru/C, whereas the same promotional effect of water is not observed for Pt-based catalysts. Microkinetic model predictions for the hydrogenation of acetone on Ru in the absence and presence of water, using enthalpies and entropies obtained from DFT calculations, were in agreement with the experimentally observed reaction orders and activation barriers. The model shows that a water-assisted hydroxypropyl path is expected to be the favored path on Ru with a rate-determining step of H-OH-mediated hydrogenation of C 3 H 6 OH (i.e., the hydroxypropyl intermediate formed by H 2 O-mediated initial hydrogenation of acetone) to produce isopropyl alcohol (IPA). Furthermore, hydrogen, acetone, hydroxypropyl intermediate and hydroxyl species were predicted to be abundant on the Ru surface with a high coverage of nearly 85%. Lastly, the combined studies of computational and experimental catalysis on hydrogenation reactions help to elucidate the mechanistic role of water on metal catalyzed reactions for producing chemical building blocks from biomass-derived oxygenates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Enhanced descriptor identification and mechanism understanding for catalytic activity using a data-driven framework: revealing the importance of interactions between elementary steps

We report accurate identification of descriptors for catalytic activities has long been essential to the in-depth understanding of catalysis and recently to set the basis for catalyst screening. However, commonly used methods suffer from low accuracy in predictability. This study reports an enhanced approach to accurately identify the descriptors from a kinetic dataset using a machine learning (ML) surrogate model. CO hydrogenation to methanol over Cu-based catalysts was taken as a case study. Our model captures not only the contribution from individual elementary steps but also the interaction between relevant steps within a reaction network, which was found to be essential for high accuracy. As a result, six effective descriptors are identified, which are accurate enough to ensure the trained gradient boosted regression (GBR) model for good prediction of the methanol turnover frequency (TOF) over metal (M)-doped Cu(111) model surfaces (M = Au, Cu, Pd, Pt, Ni). More importantly, going beyond the purely mathematical ML model, the catalytic role of each identified descriptor can be revealed by using model-agnostic interpretation tools, which enhances the insight into the promoting effect of alloying. The trained GBR model outperforms the conventional derivative-based methods in terms of both the predictability and the mechanism understanding. It opens alternative possibilities toward accurate descriptor-based rational catalyst optimization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Selective butene formation in direct ethanol-to-C3+-olefin valorization over Zn-Y/Beta and single-atom alloy composite catalysts using in situ generated hydrogen

The selective production of C3+ olefins from renewable feedstocks, especially via C1 and C2 platform chemicals, is a critical challenge for obtaining economically viable low-carbon middle distillate transportation fuels (i.e., jet and diesel). Here, we report a multifunctional catalyst system composed of Zn-Y/Beta and “single-atom” alloy (SAA) Pt-Cu/Al2O3 which selectively catalyzes ethanol-to-olefins (C3+, ETO) valorization in the absence of cofed hydrogen, forming butenes as the primary olefin products. Beta zeolites containing predominately isolated Zn and Y metal sites catalyze ethanol upgrading steps (588 K, 3.1 kPa ethanol, ambient pressure) regardless of cofed hydrogen partial pressure (0-98.3 kPa H2), forming butadiene as the primary product (60% selectivity at 87% conversion). The Zn-Y/Beta catalyst possesses site-isolated Zn and Y Lewis acid sites (at ~7 wt% Y) and Brønsted acidic Y sites, the latter of which has been previously uncharacterized. A secondary bed of SAA Pt-Cu/Al2O3 selectively hydrogenates butadiene to butene isomers at a consistent reaction temperature using hydrogen generated in situ from ethanol-to-butadiene (ETB) conversion. This unique hydrogenation reactivity at near-stoichiometric hydrogen and butadiene partial pressures is not observed over monometallic Pt or Cu catalysts, highlighting these operating conditions as a critical SAA catalyst application area for conjugated diene selective hydrogenation at high reaction temperatures (>573 K) and low H2/diene ratios (e.g., 1:1). Single-bed steady state selective hydrogenation rates, associated apparent hydrogen and butadiene reaction orders, and DFT calculations of the Horiuti-Polanyi reaction mechanisms indicate that the unique butadiene selective hydrogenation reactivity over SAA Pt-Cu/Al2O3 reflects lower hydrogen scission barriers relative to monometallic Cu surfaces and limited butene binding energies relative to monometallic Pt surfaces. DFT calculations further indicate the preferential desorption of butene isomers over SAA Pt-Cu(111) and Cu(111) surfaces while Pt(111) surface favors subsequent butene hydrogenation reactions to form butane over butene desorption events. Under operating conditions without of hydrogen cofeeding, this combination of Zn-Y/Beta and SAA Pt-Cu catalysts can selectively form butenes (65% butenes, 78% C3+ selectivity at 94% conversion) and avoid butane formation using only in situ generated hydrogen, avoiding costly hydrogen cofeeding requirements that hinder many renewable energy processes.

Cordon, Michael↗
DOE OSTI2021

Identification of earth-abundant materials for selective dehydrogenation of light alkanes to olefins

Catalytic alkane dehydrogenation is of considerable importance in the synthesis of olefins industrially. However, discovery of highly active, selective, and stable heterogeneous catalysts to replace noble metal Pt remains challenging. By combining descriptor-based microkinetic modeling, high-throughput computations, machine-learning concepts, and experiments, we efficiently evaluated 1,998 bimetallic alloys and successfully identified Ni 3 Mo as one of the most promising catalysts in selective ethane dehydrogenation. This work will open new possibilities of using earth-abundant materials as catalysts for essential heterogeneous catalytic reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Interpretable design of Ir-free trimetallic electrocatalysts for ammonia oxidation with graph neural networks

The electrochemical ammonia oxidation to dinitrogen as a means for energy and environmental applications is a key technology toward the realization of a sustainable nitrogen cycle. The state-of-the-art metal catalysts including Pt and its bimetallics with Ir show promising activity, albeit suffering from high overpotentials for appreciable current densities and the soaring price of precious metals. Herein, the immense design space of ternary Pt alloy nanostructures is explored by graph neural networks trained on ab initio data for concurrently predicting site reactivity, surface stability, and catalyst synthesizability descriptors. Among a few Ir-free candidates that emerge from the active learning workflow, Pt 3 Ru-M (M: Fe, Co, or Ni) alloys were successfully synthesized and experimentally verified to be more active toward ammonia oxidation than Pt, Pt 3 Ir, and Pt 3 Ru. More importantly, feature attribution analyses using the machine-learned representation of site motifs provide fundamental insights into chemical bonding at metal surfaces and shed light on design strategies for high-performance catalytic systems beyond the d-band center metric of binding sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗