Search NASA⌕ Search

SEARCH · Search NASA

Results for “REGRESSION COEFFICIENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Empirical Modeling of Direct Expansion (DX) Cooling System for Multiple Research Use Cases

This study provides a general procedure to generate a direct expansion (DX) cooling coil system for a roof top unit (RTU), which is a typical heating ventilation and air-conditioning (HVAC) system for commercial buildings in the United States. Experimental data from a full-scale unoccupied 2-story commercial building is used for the HVAC modeling. The regression for identifying the model coefficients was carried out with multiple stages, and the results were validated with measured data. The model’s applicability was evaluated with multiple case studies, including a building energy simulation (BES) program validation, model-based predictive control (MPC), and fault diagnostics and detection (FDD).

42 ENGINEERING↗
NASA NTRS1974

Evaluation of membrane filter field monitors for microbiological air sampling

Due to area constraints encountered in assembly and testing areas of spacecraft, the membrane filter field monitor (MF) and the National Aeronautics and Space Administration-accepted Reyniers slit air sampler were compared for recovery of airborne microbial contamination. The intramural air in a microbiological laboratory area and a clean room environment used for the assembly and testing of the Apollo spacecraft was studied. A significantly higher number of microorganisms was recovered by the Reyniers sampler. A high degree of consistency between the two sampling methods was shown by a regression analysis, with a correlation coefficient of 0.93. The MF samplers detected 79% of the concentration measured by the Reyniers slit samplers. The types of microorganisms identified from both sampling methods were similar.

Fields, N. D.↗
NASA NTRS1982

On redistribution and the equations for radiative transfer

The derivation of the equations of statistical equilibrium are outlined, starting from the quantum density-matrix equations, drawing particular attention to the approximations and assumptions used in the development of tractable expressions. Then, using the quantum-fluctuation-regression theorem, emission and absorption coefficients are obtained for multilevel atomic systems which are nondegenerate except for m-substates. These coefficients are valid to first order in the incident intensity. Possible extensions to higher intensity broadband incoherent fields are suggested.

Cooper, J.↗
NASA NTRS2001

Comparison of DMSP SSM/I and Landsat 7 ETM+ Sea Ice Concentrations During Summer Melt

As part of NASA's EOS Aqua sea ice validation program for the Advanced Microwave Scanning Radiometer (AMSR-E), Landsat 7 Enhanced Thematic Mapper (ETM+) images were acquired to develop a sea ice concentration data set with which to validate AMSR-E sea ice concentration retrievals. The standard AMSR-E Arctic sea ice concentration product will be obtained with the enhanced NASA Team (NT2) algorithm. The goal of this study is to assess the accuracy to which the NT2 algorithm, using DMSP Special Sensor Microwave Imager radiances, retrieves sea ice concentrations under summer melt conditions. Melt ponds are currently the largest source of error in the determination of Arctic sea ice concentrations with satellite passive microwave sensors. To accomplish this goal, Landsat 7 ETM+ images of Baffin Bay were acquired under clear sky conditions on the 26th and 27th of June 2000 and used to generate high-resolution sea ice concentration maps with which to compare the NT2 retrievals. Based on a linear regression analysis of 116 25-km samples, we find that overall the NT2 retrievals agree well with the Landsat concentrations. The regression analysis yields a correlation coefficient of 0.98. In areas of high melt ponding, the NT2 retrievals underestimate the sea ice concentrations by about 12% compared to the Landsat values.

Cavalieri, Donald J.↗
NASA NTRS2007

Data Mining Methods Applied to Flight Operations Quality Assurance Data: A Comparison to Standard Statistical Methods

In a previous study, multiple regression techniques were applied to Flight Operations Quality Assurance-derived data to develop parsimonious model(s) for fuel consumption on the Boeing 757 airplane. The present study examined several data mining algorithms, including neural networks, on the fuel consumption problem and compared them to the multiple regression results obtained earlier. Using regression methods, parsimonious models were obtained that explained approximately 85% of the variation in fuel flow. In general data mining methods were more effective in predicting fuel consumption. Classification and Regression Tree methods reported correlation coefficients of .91 to .92, and General Linear Models and Multilayer Perceptron neural networks reported correlation coefficients of about .99. These data mining models show great promise for use in further examining large FOQA databases for operational and safety improvements.

Stolzer, Alan J.↗
NASA NTRS2009

Skill Assessment of a Spectral Ocean-Atmosphere Radiative Model

Ocean phytoplankton, detrital material, and water absorb and scatter light spectrally. The Ocean- Atmosphere Spectral Irradiance Model (OASIM) is intended to provide surface irradiance over the oceans with sufficient spectral resolution to support ocean ecology, biogeochemistry, and heat exchange investigations, and of sufficient duration to support inter-annual and decadal investigations. OASIM total surface irradiance (integrated 200 nm to 4 microns) was compared to in situ data and three publicly available global data products at monthly 1-degree resolution. OASIM spectrally-integrated surface irradiance had root mean square (RMS) difference= 20.1 W/sq m (about 11%), bias=1.6 W/sq m (about 0.8%), regression slope= 1.01 and correlation coefficient= 0.89, when compared to 2322 in situ observations. OASIM had the lowest bias of any of the global data products evaluated (ISCCP-FD, NCEP, and ISLSCP 11), and the best slope (nearest to unity). It had the second best RMS, and the third best correlation coefficient. OASIM total surface irradiance compared well with ISCCP-FD (RMS= 20.7 W/sq m; bias=-11.4 W/sq m, r=0.98) and ISLSCP II (RMS =25.2 W/sq m; bias= -13.8 W/sq m; r=0.97), but less well with NCEP (RMS =43.0 W/sq m ;bias=-22.6 W/sq m; x=0.91). Comparisons of OASIM photosynthetically available radiation (PAR) with PAR derived from SeaWiFS showed low bias (-1.8 mol photons /sq m/d, or about 5%), RMS (4.25 mol photons /sq m/d ' or about 12%), near unity slope (1.03) and high correlation coefficient (0.97). Coupled with previous estimates of clear sky spectral irradiance in OASIM (6.6% RMS at 1 nm resolution), these results suggest that OASIM provides reasonable estimates of surface broadband and spectral irradiance in the oceans, and can support studies on ocean ecosystems, carbon cycling, and heat exchange.

Gregg, Watson, W.↗
NASA NTRS2011

Multi-Axis Identifiability Using Single-Surface Parameter Estimation Maneuvers on the X-48B Blended Wing Body

The problem of parameter estimation on hybrid-wing-body type aircraft is complicated by the fact that many design candidates for such aircraft involve a large number of aero- dynamic control effectors that act in coplanar motion. This fact adds to the complexity already present in the parameter estimation problem for any aircraft with a closed-loop control system. Decorrelation of system inputs must be performed in order to ascertain individual surface derivatives with any sort of mathematical confidence. Non-standard control surface configurations, such as clamshell surfaces and drag-rudder modes, further complicate the modeling task. In this paper, asymmetric, single-surface maneuvers are used to excite multiple axes of aircraft motion simultaneously. Time history reconstructions of the moment coefficients computed by the solved regression models are then compared to each other in order to assess relative model accuracy. The reduced flight-test time required for inner surface parameter estimation using multi-axis methods was found to come at the cost of slightly reduced accuracy and statistical confidence for linear regression methods. Since the multi-axis maneuvers captured parameter estimates similar to both longitudinal and lateral-directional maneuvers combined, the number of test points required for the inner, aileron-like surfaces could in theory have been reduced by 50%. While trends were similar, however, individual parameters as estimated by a multi-axis model were typically different by an average absolute difference of roughly 15-20%, with decreased statistical significance, than those estimated by a single-axis model. The multi-axis model exhibited an increase in overall fit error of roughly 1-5% for the linear regression estimates with respect to the single-axis model, when applied to flight data designed for each, respectively.

Ratnayake, Nalin A.↗
NASA NTRS2012

Improvement of Aerosol Optical Depth Retrieval from MODIS Spectral Reflectance over the Global Ocean Using New Aerosol Models Archived from AERONET Inversion Data and Tri-axial Ellipsoidal Dust Database

New over-ocean aerosol models are developed by integrating the inversion data from the Aerosol Robotic Network (AERONET) sun/sky radiometers with a database for the optical properties of tri-axial ellipsoid particles. The new aerosol models allow more accurate retrieval of aerosol optical depth (AOD) from the Moderate Resolution Imaging Spectroradiometer (MODIS) in the case of high AOD (AOD greater than 0.3). The aerosol models are categorized by using the fine-mode fraction (FMF) at 550 nm and the singlescattering albedo (SSA) at 440 nm from the AERONET inversion data to include a variety of aerosol types found around the globe. For each aerosol model, the changes in the aerosol optical properties (AOPs) as functions of AOD are considered to better represent aerosol characteristics. Comparisons of AODs between AERONET and MODIS for the period from 2003 to 2010 show that the use of the new aerosol models enhances the AOD accuracy with a Pearson coefficient of 0.93 and a regression slope of 0.99 compared to 0.92 and 0.85 calculated using the MODIS Collection 5 data. Moreover, the percentage of data within an expected error of +/-(0.03 + 0.05xAOD) is increased from 62 percent to 64 percent for overall data and from 39 percent to 51 percent for AOD greater than 0.3. Errors in the retrieved AOD are further characterized with respect to the Angstrom exponent (AE), scattering angle, SSA, and air mass factor (AMF). Due to more realistic AOPs assumptions, the new algorithm generally reduces systematic errors in the retrieved AODs compared with the current operational algorithm. In particular, the underestimation of fine-dominated AOD and the scattering angle dependence of dust-dominated AOD are significantly mitigated as results of the new algorithm's improved treatment of aerosol size distribution and dust particle nonsphericity.

aerosol optical depth↗
NASA NTRS2023

Solar Activity Relations in Energetic Electron Events Measured By the MESSENGER Mission

Aims. We perform a statistical study of the relations between the properties of solar energetic electron (SEE) events measured by the MESSENGER mission from 2010 to 2015 and the parameters of the respective parent solar activity phenomena in order to identify the potential correlations between them. During the time of analysis, the MESSENGER heliocentric distance varied between 0.31 and 0.47 au. Methods. We used a published list of 61 SEE events measured by MESSENGER, which includes information on the near-relativistic electron peak intensities, the peak-intensity energy spectral indices, and the measured X-ray peak intensity of the flares related to the SEE events. Taking advantage of multi-viewpoint remote-sensing observations, we reconstructed, whenever possible, the associated coronal mass ejections (CMEs) and shock waves; and we determined the three-dimensional (3D) properties (location, speed, and width) of the CMEs and the maximum speed of the 3D CME-driven shocks in the corona. We used different methods (Spearman, Pearson, and a Bayesian approach, namely the Kelly method to linear regression) to estimate the correlation coefficients between the flare intensity, maximum speed at the apex of the CME-driven shock, CME speed at the apex, and CME width with the electron peak intensities and with the energy spectral indices. In this statistical study, we considered and addressed the limitations of the particle instrument on board MESSENGER (elevated background intensity level, anti-Sun pointing). Results. There is an asymmetry to the east in the range of connection angles (CAs) for which the SEE events present the highest peak intensities, where the CA is the longitudinal separation between the footpoint of the magnetic field connecting to the spacecraft and the flare location. Based on this asymmetry, we define a subsample of well-connected events as when −65° ≤ CA ≤ +33°. For the well-connected sample, we find moderate to strong correlations between the near-relativistic electron peak intensity and the 3D CME-driven shock maximum speed at the apex (Spearman: cc = 0.53 ± 0.05; Pearson: cc = 0.65 ± 0.04; Kelly: cc = 0.87 ± 0.20), the flare peak intensity (Spearman: cc = 0.63 ± 0.03; Pearson: cc = 0.59 ± 0.03; Kelly: cc = 0.74 ± 0.30), and the 3D CME speed at the apex (Spearman: cc = 0.50 ± 0.04; Pearson: cc = 0.46 ± 0.03; Kelly: cc = 0.60 ± 0.39). When including poorly connected events (full sample), the relations between the peak intensities and the solar-activity phenomena are blurred, showing lower correlation coefficients. Conclusions. Based on the comparison of the correlation coefficients presented in this study using near 0.4 au data, (1) both flare and shock-related processes may contribute to the acceleration of near relativistic electrons in large SEE events, in agreement with previous studies based on near 1 au data; and (2) the maximum speed of the CME-driven shock is a better parameter to investigate particle-acceleration-related mechanisms than the average CME speed, as suggested by the stronger correlation with the SEE peak intensities.

Sun↗
DOE OSTI2025

Uniting Surface Properties With Hydrodynamic Roughness in Shallow Overland Flow Models

Describing flow resistance from the properties of an underlying surface is a challenge in surface hydrology. Runoff models must specify a resistance formulation or “roughness scheme”—describing the functional relationship between flow resistance and flow depth/velocity—and its parameters. Uncertainty in runoff predictions derives from both the selected roughness scheme (e.g., Darcy Weisbach, Manning's, or laminar flow equations), and its parameterization with a roughness coefficient (e.g., Manning's n). Both choices are informed by model calibration to data, usually discharge, and, if available, velocity. In this study, a Saint Venant Equation-based runoff model is calibrated to discharge and velocity data from 112 rainfall simulator experiments. The results are used to identify the optimal roughness scheme among four widely-used options for each experiment, and to explore whether surface properties can be used to select the optimal roughness scheme and its coefficient. Among the tested roughness schemes, a transitional flow equation provided the best fit to the plurality of experiments. The most suitable roughness scheme for a given experiment was not related to measured surface properties. Regression models predicted the calibrated roughness coefficients with adjusted values between 0.48 and 0.54, depending on the roughness scheme used. Litter cover was the best predictor of the roughness coefficient, followed by soil cover and average canopy gap size. The results suggest that selection of an optimal roughness scheme based on surface properties alone remains difficult, but that once a scheme is selected, roughness coefficients can be estimated from surface properties.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1994

Understanding software faults and their role in software reliability modeling

This study is a direct result of an on-going project to model the reliability of a large real-time control avionics system. In previous modeling efforts with this system, hardware reliability models were applied in modeling the reliability behavior of this system. In an attempt to enhance the performance of the adapted reliability models, certain software attributes were introduced in these models to control for differences between programs and also sequential executions of the same program. As the basic nature of the software attributes that affect software reliability become better understood in the modeling process, this information begins to have important implications on the software development process. A significant problem arises when raw attribute measures are to be used in statistical models as predictors, for example, of measures of software quality. This is because many of the metrics are highly correlated. Consider the two attributes: lines of code, LOC, and number of program statements, Stmts. In this case, it is quite obvious that a program with a high value of LOC probably will also have a relatively high value of Stmts. In the case of low level languages, such as assembly language programs, there might be a one-to-one relationship between the statement count and the lines of code. When there is a complete absence of linear relationship among the metrics, they are said to be orthogonal or uncorrelated. Usually the lack of orthogonality is not serious enough to affect a statistical analysis. However, for the purposes of some statistical analysis such as multiple regression, the software metrics are so strongly interrelated that the regression results may be ambiguous and possibly even misleading. Typically, it is difficult to estimate the unique effects of individual software metrics in the regression equation. The estimated values of the coefficients are very sensitive to slight changes in the data and to the addition or deletion of variables in the regression equation. Since most of the existing metrics have common elements and are linear combinations of these common elements, it seems reasonable to investigate the structure of the underlying common factors or components that make up the raw metrics. The technique we have chosen to use to explore this structure is a procedure called principal components analysis. Principal components analysis is a decomposition technique that may be used to detect and analyze collinearity in software metrics. When confronted with a large number of metrics measuring a single construct, it may be desirable to represent the set by some smaller number of variables that convey all, or most, of the information in the original set. Principal components are linear transformations of a set of random variables that summarize the information contained in the variables. The transformations are chosen so that the first component accounts for the maximal amount of variation of the measures of any possible linear transform; the second component accounts for the maximal amount of residual variation; and so on. The principal components are constructed so that they represent transformed scores on dimensions that are orthogonal. Through the use of principal components analysis, it is possible to have a set of highly related software attributes mapped into a small number of uncorrelated attribute domains. This definitively solves the problem of multi-collinearity in subsequent regression analysis. There are many software metrics in the literature, but principal component analysis reveals that there are few distinct sources of variation, i.e. dimensions, in this set of metrics. It would appear perfectly reasonable to characterize the measurable attributes of a program with a simple function of a small number of orthogonal metrics each of which represents a distinct software attribute domain.

Munson, John C.↗
DOE OSTI2022

GenMod: A generative modeling approach for spectral representation of PDEs with random inputs

Here, we propose a method for quantifying uncertainty in high-dimensional PDE systems with random parameters, where the number of solution evaluations is small. Parametric PDE solutions are often approximated using a spectral decomposition based on polynomial chaos expansions. For the class of systems we consider (i.e., high dimensional with limited solution evaluations) the coefficients are given by an underdetermined linear system in a regression formulation. This implies additional assumptions, such as sparsity of the coefficient vector, are needed to approximate the solution. Here, we present an approach where we assume the coefficients are close to the range of a generative model that maps from a low to a high dimensional space of coefficients. Our approach is inspired be recent work examining how generative models can be used for compressed sensing in systems with random Gaussian measurement matrices. Using results from PDE theory on coefficient decay rates, we construct an explicit generative model that predicts the polynomial chaos coefficient magnitudes. The algorithm we developed to find the coefficients, which we call GenMod, is composed of two main steps. First, we predict the coefficient signs using Orthogonal Matching Pursuit. Then, we assume the coefficients are within a sparse deviation from the range of a sign-adjusted generative model. This allows us to find the coefficients by solving a nonconvex optimization problem, over the input space of the generative model and the space of sparse vectors. We obtain theoretical recovery results for a Lipschitz continuous generative model and for a more specific generative model, based on coefficient decay rate bounds. We examine three high-dimensional problems and show that, for all three examples, the generative model approach outperforms sparsity promoting methods at small sample sizes.

97 MATHEMATICS AND COMPUTING↗
NASA NTRSDate not supplied

Machine Learning Applications to Metal-Silicate Equilibria and their Insights into Core Formation

An extensive number of studies have experimentally investigated how elements distribute between metal and silicate phases, to better constrain core-mantle chemical equilibrium. Here, we present a new database compiling all (to our knowledge) experimental data on liquid metal-silicate partitioning from 118 peer-reviewed publications. We applied various machine learning techniques to gain further insights into these partitioning equilibria and their dependencies. We performed a network analysis to investigate the relationship between experiments and partition coefficients, which enables visualizing gaps in the experimental dataset and biases related to varying experimental conditions and analytical setup. In addition, semi-empirical thermodynamic models are commonly used to extrapolate these chemical reactions to the wide range of pressure, temperature and compositional conditions of planetary differentiation. These models are based on linear regressions that assume continuous relationship between partition coefficients and experimental variables. Here, we considered random forest regressions, which are algorithms based on ensembles of decision trees and does not consider continuous effects of each variable. The application of this regression significantly improves the prediction of metal-silicate partitioning for several elements including Ni, Si and Cr. We will show how this new approach improves our understanding of elemental exchange between metal and silicate and their implications for the Earth’s core formation.

siderophile element↗
DOE OSTI2022

Proposal and application of ROM-Lasso method for sensitivity coefficient evaluation

We propose a novel method for evaluating sensitivity coefficients of neutronics parameters to cross sections, so-called the reduced-order modeling technique ROM-Lasso. In this method, cross sections of interest are randomly sampled, and corresponding perturbed core analyses are performed. Then, the sensitivity coefficient vector of the higher-level model is expanded via the active subspace bases obtained with the lower-level model whose dimensional complexity is smaller than that of the higher-level model, and the expansion coefficients are estimated by the Lasso regression. A unique feature of the ROM-Lasso method allows the use of different bases optimized for each neutronics parameter. We conducted a verification calculation for an accelerator-driven system and demonstrated that the ROM-Lasso method can reproduce the sensitivity coefficients with a much smaller number of forward calculations than the direct method. The proposed method can be used to practically evaluate sensitivity coefficients. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1986

Heat and mass transfer rates during flow of dissociated hydrogen gas over graphite surface

To improve upon the performance of chemical rockets, the nuclear reactor has been applied to a rocket propulsion system using hydrogen gas as working fluid and a graphite-composite forming a part of the structure. Under the boundary layer approximation, theoretical predictions of skin friction coefficient, surface heat transfer rate and surface regression rate have been made for laminar/turbulent dissociated hydrogen gas flowing over a flat graphite surface. The external stream is assumed to be frozen. The analysis is restricted to Mach numbers low enough to deal with the situation of only surface-reaction between hydrogen and graphite. Empirical correlations of displacement thickness, local skin friction coefficient, local Nusselt number and local non-dimensional heat transfer rate have been obtained. The magnitude of the surface regression rate is found low enough to ensure the use of graphite as a linear or a component of the system over an extended period without loss of performance.

Nema, V. K.↗
DOE OSTI2022

Accurate parameterization of the kinetic energy functional for calculations using exact-exchange

In this report, electronic structure calculations based on Kohn-Sham density functional theory (KSDFT) that incorporate exact exchange or hybrid functionals are associated with large computational expense, a consequence of the inherent cubic scaling bottleneck and large associated prefactor, which limits the length and time scales that can be accessed. Though orbital-free density functional theory (OFDFT) calculations scale linearly with system size and are associated with significantly smaller prefactor, they are limited by the absence of accurate density-dependent kinetic energy functionals. Therefore, the development of accurate density-dependent kinetic energy functionals is important for OFDFT calculations of large realistic systems. To this end, we propose a method to train kinetic energy functional models at the exact-exchange level of theory by using a dictionary of physically relevant terms that have been proposed in the literature in conjunction with linear or nonlinear regression methods to obtain the fitting coefficients. For our dictionary, we use gradient expansion of the kinetic energy, nonlocal models proposed in the literature and their nonlinear combinations, such as a model that incorporates spatial correlations between higher order derivatives of electron density at two points. The predictive capabilities of these models are assessed by using a variety of model one-dimensional systems that exhibit diverse bonding characteristics, such as a chain of eight hydrogens, LiF, LiH, C 4 H 2 , C 4 N 2 and C 3 O 2 . We show that by using data from model one-dimensional KSDFT calculations performed using the exact-exchange functional for only a few neutral structures, it is possible to generate models with high accuracy for charged systems as well as electron and kinetic energy densities during self-consistent field iterations. In addition, we show that it possible to learn both the orbital dependent terms, i.e., the kinetic energy and the exact-exchange energy, and models that incorporate additional nonlinearities in spatial correlations, such as a quadratic model, are needed to capture subtle features of the kinetic energy density that are present in exact-exchange-based KSDFT calculations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1983

Determination of airplane model structure from flight data using splines and stepwise regression

A procedure for the determination of airplane model structure from flight data is presented. The model is based on a polynomial spline representation of the aerodynamic coefficients, and the procedure is implemented by use of a stepwise regression. First, a form of the aerodynamic force and moment coefficients amenable to the utilization of splines is developed. Next, expressions for the splines in one and two variables are introduced. Then the steps in the determination of an aerodynamic model structure and the estimation of parameters are discussed briefly. The focus is on the application to flight data of the techniques developed.

Klein, V.↗
DOE OSTI2021

Assessment the leaching characteristics and long-term leaching behavior of some radionuclides from synthesized zeolite cement matrix

Highlights: • Synthesis and characterization of zeolite cement synthesized from fly ash • Leaching tests were used to assess the release rate of {sup 85}Sr and {sup 60}Co radionuclides. • Simple mathematical models were used to detect leaching mechanisms. • Long-term leaching behavior of {sup 85}Sr and {sup 60}Co from cementitious matrix was assessed. The development of cementitious materials remains a vital goal to produce valuable products with good mechanical, physical and chemical properties suitable for the safe disposal of concentrated radionuclides resulted from the treatment of contaminated solutions. In this paper, zeolite cement with good properties was laboratory synthesized from industrial by-products fly ash and characterized using various characterization techniques. The leaching characteristics of strontium and cobalt radionuclides from the synthesized zeolite cement were scrutinized conforming with the standard leaching methodology of International Atomic Energy Authority (IAEA). A mechanical strength assessment was executed to characterize the extent of immobilization process of the solidified matrices. The cumulative leaching fraction (φ) of the two studied radionuclides was found to be less than 5% in all examined conditions, which implies the applicability of the IAEA-recommended methodology for estimating the diffusion coefficient. The experimental leaching data were regressed nonlinearly to various mathematical kinetic models to assess the controlling leaching mechanism and to determine the leaching parameters. The regression results indicated that strontium ({sup 85}Sr) and cobalt ({sup 60}Co) leaching resulted from two succeeding mechanisms: as first order kinetic reaction, and then diffusion. The calculated values of leachability indices signify that the performance of each of the studied matrices is within an acceptable range. A simplified mathematical model, rooted in the first order reaction and diffusion mechanisms, was simulated to predict the radionuclides leaching rates from zeolite cement matrices. By comparing the synthesized zeolite cement with other cementitious materials, it can be concluded that the synthesized material can be classified as an efficient material suitable to immobilize {sup 85}Sr and {sup 60}Co from radioactive wastes. The acquired findings demonstrated that the studied immobilized waste matrices have acceptable mechanical effectiveness.

36 MATERIALS SCIENCE↗