Search NASA⌕ Search

SEARCH · Search NASA

Results for “RESIDUAL STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Effects of mechanical and thermal cycling on composite and hybrid laminates with residual stresses

The effects of tensile load cycling and thermal cycling on residual stiffness and strength properties of the following composite and hybrid angle-ply laminates were studied: boron/epoxy, boron/polyimide, graphite/low-modulus epoxy, graphite/high-modulus epoxy, graphite/polyimide, S-glass/epoxy, graphite/Kevlar 49/epoxy, and graphite/S-glass/epoxy. Specimens of the first six types were mechanically cycled up to 90% of static strength. Those that survived 10 million cycles were tested statically to failure, and no significant changes in residual strength and modulus were noted. Specimens of all types were subjected to thermal cycling between room temperature and 411 K for the epoxy-matrix composites and 533 K for the polyimide-matrix composites. The residual strength and stiffness remained largely unchanged, except for the graphite/low-modulus epoxy, which showed reductions in both of approximately 35%. When low-temperature thermal cycling under tensile load was applied, there was a noticeable reduction in modulus and strength in the graphite/low-modulus epoxy and some strength reduction in the S-glass/epoxy.

Daniel, I. M.↗
NASA NTRS1986

The 14 month wind stressed residual circulation (pole tide) in the North Sea

From published research it is known that a quasi-periodic 14 month atmospheric pressure oscillation of a few tenths of a millibar exists in the region of the North and Baltic Seas. At some time in the cycle the associated wind stress has a westerly component that drives a circulation in the North Sea. The results of a dynamical model and comparisons with several North Sea residual circulation studies show that a large sea level gradient results along the Dutch coast. It is this feature that has been referred to as the enhanced pole tide. The dynamical similarity of this pole tide in the North and Baltic Seas to the annual and seasonal wind forced circulations is considered. It is inferred that the large deviations of the pole tide from equilibrium at coastal stations are the result of this sea level set up forces by the 14 month wind stress cycle.

Oconnor, W. P.↗
DOE OSTI2025

Improved Weld Residual Stress Modeling System in BlackBear

This report presents enhancements to the MOOSE-based BlackBear application aimed at improving its capability to simulate welding and other thermo-mechanical manufacturing processes. Two primary avenues of improvement are pursued. First, to enhance user accessibility, we introduce a centralized default block restriction mechanism that ensures coverage checks are performed within user-specified default blocks. This default setting is applied consistently to all block-describable objects, such as variables, kernels, and more. In addition, we develop a modular action for moving heat source simulations, which integrates path file parsing, subdomain modification, and heat source kernel enforcement into a single, streamlined configuration. Second, to improve solver robustness, we implement an alternative method for assigning initial conditions to the updated active domain during the simulation, thereby enhancing convergence behavior. To validate the framework, we design and conduct several benchmark simulations, including heat conduction with progressive material addition, linear elasticity with time-dependent material deposition, and viscoplasticity model with isotropic hardening under similar conditions. Finally, we demonstrate the effectiveness of the proposed framework through large-scale thermo-mechanical welding simulations in both two and three dimensions.

42 ENGINEERING↗
DOE OSTI2026

Fracture Analysis of Cohesive Zone Models for Modeling Residual Stress Induced Delamination in Composite Structures

A fracture study of coupon-scale composite cylinders with embedded defects was conducted with an objective to assess and validate a modeling approach using two available cohesive material models. The study included experimental and simulation evaluations of initiation of crack growth and progression. Interrupted thermal experiments used acoustic emissions monitoring to identify the onset of crack progression during each cooling interval and ultrasonic scanning provided images of defect growth. Verification, validation, and uncertainty quantification (VVUQ) processes were performed in the assessment of the simulation predicted temperature at which crack propagation begins (quantity of interest). The Sobol sensitivity analysis identified the hoop direction elastic modulus in the carbon fiber reinforced polymer (CFRP) plies as the most influential parameter for simulations using both cohesive models, accounting for at least 70% of the variation in the temperature at crack propagation. The UQ temperature range for the Tvergaard-Hutchinson model was higher (more conservative) than the experimental acoustic measurement indicators of crack progression, while the temperature range for the Thouless-Parmigiani model enveloped the experimental data points for the primary defect size of 0.75 x 1 in. The simulations could not capture the stable crack growth indicated in the experiments. This is likely due to the models’ inability to represent anisotropic fracture toughness attributed to the structure of the orthotropic fiber weave in a woven composite laminate.

42 ENGINEERING↗
NASA NTRS1984

Nondestructive evaluation of residual stress in low-carbon steel

The effects of the preferred orientation on the temperature dependence of ultrasonic velocity in low carbon steels are investigated. The sensitivity of the acousto-elastic constant to changes in microstructure is assessed as well as the possibility of determining some mechanical properties of a material by measuring the acousto-elastic constant.

Salama, K.↗
NASA NTRS1984

Nondestructive evaluation of residual stress in low-carbon steel, introduction

The degree of insensitivity of the temperature dependence method to variations in preferred orientations in A508 low carbon steel specimens was determined. A pulsed phase locked loop was used to measure ultrasonic velocity in these specimens in the temperature range of 50 C below and above room temperature. Results are given in tables and indicate that the temperature dependence of ultrasonic longitudinal velocity in four specimens cut at different angles remains unchanged as a function of orientation within + or -2%. The variation of temperature dependence of ultrasonic shear velocity in the A508 steel as a function of applied stresses was also measured. Results show that values at zero stress are equal regardless of whether the polarization direction is parallel or perpendicular to the direction in which the stress is applied.

Source record↗
NASA NTRS1988

Review of magnetoacoustic residual stress measurement technique for iron-like ferromagnetic alloys

It is shown that the elastic moduli of ironlike ferromagnetics depends explicitly on the state of 90 deg domain walls: the more 90 deg domain wall area available, the lower the elastic modulus. New experimental results obtained for three types of carbon and pure iron samples are presented. The magnetoacoustic response due to magnetization perpendicular to the uniaxial stress axis is considered as well as the magnetoacoustic response due to magnetization parallel to the uniaxial stress axis.

Namkung, M.↗
NASA NTRS2001

Development of a Novel Method for Determination of Residual Stresses in a Friction Stir Weld

Material constitutive properties, which describe the mechanical behavior of a material under loading, are vital to the design and implementation of engineering materials. For homogeneous materials, the standard process for determining these properties is the tensile test, which is used to measure the material stress-strain response. However, a majority of the applications for engineering materials involve the use of heterogeneous materials and structures (i.e. alloys, welded components) that exhibit heterogeneity on a global or local level. Regardless of the scale of heterogeneity, the overall response of the material or structure is dependent on the response of each of the constituents. Therefore, in order to produce materials and structures that perform in the best possible manner, the properties of the constituents that make up the heterogeneous material must be thoroughly examined. When materials exhibit heterogeneity on a local level, such as in alloys or particle/matrix composites, they are often treated as statistically homogenous and the resulting 'effective' properties may be determined through homogenization techniques. In the case of globally heterogeneous materials, such as weldments, the standard tensile test provides the global response but no information on what is Occurring locally within the different constituents. This information is necessary to improve the material processing as well as the end product.

Reynolds, Anthony P.↗