Search NASA⌕ Search

SEARCH · Search NASA

Results for “RF Measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Cryogenic-Refined MOSFET Modeling for Oscillator, Frequency Divider, and Amplifier Designs Below 4 K

Capturing device characteristic changes at cryogenic temperatures is crucial for cryo-CMOS circuit designs. In this work, we present an isothermal cryogenic-refined modeling approach for CMOS transistors that is simple, low overhead, and easy to implement while offering the required accuracy for predicting circuit performance at the designated temperatures. Guided by die-level measurement data and circuit design principles, the model introduces corrections to only five critical parameters: threshold voltage, carrier mobility, elevated low-frequency flicker noise, dominant high-frequency shot noise, and subthreshold swing (SS). These refinements are implemented around the foundry-provided SPICE model, which is typically validated only down to about 200 K. With these adjustments, the proposed cryogenic-refined model achieves less than 5% error in both large-signal metrics (I–V characteristics) and small-signal parameters (e.g., transconductance) when compared with device measurements at deep-cryogenic temperatures. The methodology is validated in two advanced technologies: TSMC 40-nm CMOS and GlobalFoundries (GF) 45-nm RF-SOI. We further demonstrate its applicability in three representative RF circuits: a 30-GHz LC oscillator, a high-speed current-mode-logic (CML) frequency divider (FD), and a subthreshold Gb/s amplifier, all showing close agreement between simulated predictions and measurements performed at 4 and 2.5 K. Finally, we believe that the proposed approach is implementation-friendly and can significantly accelerate the development of cryo-CMOS integrated circuits.

circuit modeling↗
DOE OSTI2020

Network-Scale Ubiquitous Volume Estimation Using Tree-Based Ensemble Learning Methods

Currently ubiquitous volume data for roadway networks remains the key missing dimension in traffic operations. Most volume data are average annual daily traffic (AADT) measures derived from the Highway Performance Monitoring System (HPMS). Although methods to factor the AADT to hourly averages for typical day of week exist, actual volume data is limited to a sparse collection of locations in which volumes are continuously recorded. This paper/poster explores the use of state-of-art machine learning techniques to estimate accurate volume measures that span the highway network providing ubiquitous coverage in space, and point-in-time measures for a specific date and time. Three tree-based ensemble learning models, random forest (RF), gradient boost machine (GBM), and extreme gradient boost (XGBoost), were tested for volume estimation by learning from combined dataset of commercial probe data provided by TomTom, the FHWA's Travel Monitoring Analysis System (TMAS) data, and other infrastructure attributes such as number of lanes, speed limit, and weather. The methods were tested on major corridors and freeways in the metropolitan area of Denver. All three machine learning methods were able to provide hourly volume estimates 24 hours a day, 7 days a week, and 365 days a year with around 18% mean absolute error to true volume and about 5% of error with respect to roadway capacity. The low error measures allow the potential application by transportation agencies.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Radio Frequency Field Programable Gate Array Implementation of Reflectometry Cable Monitoring

PNNL has developed an innovative cable testing system that leverages the Xilinx RF System-on-Chip (RFSoC) technology to create a more flexible and capable measurement tool than traditional approaches. The architecture is designed on the ZCU111 development board and takes advantage of the high-speed digital to analog converters (DAC) and analog to digital converters (ADC) to generate and capture digitally synthesized waveforms. The platform allows engineers to easily adjust power, frequency, duration and modulation on the fly rather than being locked into fixed hardware configurations

Tedeschi, Jonathan [Pacific Northwest National Lab↗
DOE OSTI2021

Observation of Undulator Radiation Generated by a Single Electron Circulating in a Storage Ring and Possible Applications

An experimental study into the undulator radiation, generated by a single electron was carried out at the Integrable Optics Test Accelerator (IOTA) storage ring at Fermilab. The individual photons were detected by a Single Photon Avalanche Diode (SPAD) at an average rate of 1 detection per 300 revolutions in the ring. The detection events were continuously recorded by a picosecond event timer for as long as 1 minute at a time. The collected data were used to test if there is any deviation from the classically predicted Poissonian photostatistics. It was motivated by the observation * of sub-Poissonian statistics in a similar experiment. The observation * could be an instrumentation effect related to low detection efficiency and long detector dead time. In our experiment, the detector (SPAD) has a much higher efficiency (65%) and a much lower dead time. In addition, we show that the collected data (recorded detection times) can be used to study the synchrotron motion of a single electron and infer some parameters of the ring. For example, by comparing the results of simulation and measurement for the synchrotron motion we were able to estimate the magnitude of the RF phase jitter.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

Enhance coherence time in intensely driven quantum systems

Not long ago, it was shown that a discrete time crystal can be realized if a quantum system is periodically driven to a non-equilibrium state. Proof-of-concept experiments are reported by two groups using trapped ions and nitrogen-vacancy centers in diamond, respectively. The concept of discrete time crystals vividly demonstrates that the coherence time of a quantum system may be enhanced by driving the system out of equilibrium. In this project, we want to test this novel concept in another canonical quantum system, the quantum Hall system in a two-dimensional electron gas (2DEG). Compared to other systems, quantum Hall magnetism (QHM) in high quality, industry-compatible GaAs/AlGaAs heterostructures allows for detailed and quantitative studies in a particularly simple and clean environment. This detailed knowledge should help achieve longer coherence times in a driven QHM system. This report will detail the results from a recent study on the stability of the quantum Hall skyrmions (QHS) state at a Landau level filling close to ν = 1 by measuring its current-voltage (I-V) breakdown characteristics under radio-frequency (RF) radiations. We observe that the critical current increases visibly when the RF frequency is right at the Larmor frequency of 75As nuclei, where the hyperfine interaction between electron and nuclear spins perturbs the QHS state most significantly. We believe that this observation is consistent with the novel concept that the coherence time of a quantum system may be enhanced by driving the system out of equilibrium.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Thermodynamic Cloud Phase Classifications Using Machine Learning at NSA and ANX

Vertically resolved thermodynamic cloud phase classifications are essential for studies of atmospheric cloud and precipitation processes. The Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) THERMOCLDPHASE Value-Added Product (VAP) uses a multi-sensor approach to classify thermodynamic cloud phase by combining lidar backscatter and depolarization, radar reflectivity, Doppler velocity, spectral width, microwave radiometer-derived liquid water path, and radiosonde temperature measurements. The measured voxels are classified as ice, snow, mixed-phase, liquid (cloud water), drizzle, rain, and liq_driz (liquid+drizzle). We use this product as the ground truth to train three machine learning (ML) models to predict the thermodynamic cloud phase from multi-sensor remote sensing measurements taken at the ARM North Slope of Alaska (NSA) observatory: a random forest (RF), a multilayer perceptron (MLP), and a convolutional neural network (CNN) with a U-Net architecture. Evaluations against the outputs of the THERMOCLDPHASE VAP with one year of data show that the CNN outperforms the other two models, achieving the highest test accuracy, F1-score, and mean Intersection over Union (IOU). Analysis of ML confidence scores shows ice, rain, and snow have higher confidence scores, followed by liquid, while mixed, drizzle, and liq_driz have lower scores. Feature importance analysis reveals that the mean Doppler velocity and vertically resolved temperature are the most influential datastreams for ML thermodynamic cloud phase predictions. The ML models’ generalization capacity is further evaluated by applying them at another Arctic ARM site in Norway using data taken during the ARM Cold-Air Outbreaks in the Marine Boundary Layer Experiment (COMBLE) field campaign. Finally, we evaluate the ML models’ response to simulated instrument outages and signal degradation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Nonlinear dynamics and dissipation of a curvilinear vortex driven by a strong time-dependent Meissner current

Here, we report numerical simulations of large-amplitude oscillations of a trapped vortex line under a strong ac magnetic field $\textit{H(t) = H}$ sin$\textit{ωt}$ parallel to the surface. The power dissipated by an oscillating vortex segment driven by the surface ac Meissner currents was calculated by taking into account the nonlinear vortex line tension, vortex mass, and a nonlinear Larkin-Ovchinnikov (LO) viscous drag coefficient $\textit{η(v)}$. We show that the LO decrease of $\textit{η(v)}$ with the vortex velocity $\textit{v}$ can radically change the field dependence of the surface resistance R i ( H ) caused by trapped vortices. At low frequencies, $R_i(H)$ exhibits a conventional increase with $\textit{H}$, but as $\textit{ω}$ increases, the surface resistance becomes a nonmonotonic function of $\textit{H}$ which decreases with $\textit{H}$ at higher fields. The effects of frequency, pin spacing, and the mean-free path $l_i$ on the field dependence of $R_i(H)$ were calculated. It is shown that, as the surface gets dirtier and $l_i$ decreases, the anomalous drop of $R_i(H)$ with $\textit{H}$ shifts to lower fields which can be much smaller than the lower critical magnetic field. Our numerical simulations also show that the LO decrease of $\textit{η(v)}$ with $\textit{v}$ can cause a vortex bending instability at high field amplitudes and frequencies, giving rise to the formation of dynamic kinks along the vortex. Measurements of $R_i(H)$ caused by sparse vortices trapped perpendicular to the surface can offer opportunities to investigate an extreme nonlinear dynamics of vortices driven by strong current densities up to the depairing limit at low temperatures. The behavior of $R_i(H)$, which can be tuned by varying the rf frequency or concentration of nonmagnetic impurities, is not masked by strong heating effects characteristic of dc or pulse transport measurements.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Enhancing nuclear data validation analysis by using machine learning

In this work, we demonstrate how machine learning (ML) techniques can be used as an auxiliary tool for nuclear data validation analysis. The output of the ML analysis can inform evaluators and validators on the quality, or lack thereof, of specific nuclear data and benchmark experiments with respect to simulating these experimental benchmark values. To this end, measured and simulated effective neutron multiplication factors, k eff , of 875 selected ICSBEP critical assemblies and the latter's sensitivities with respect to nuclear data as well as benchmarks' features (e.g., material nuclide, core geometry) are used as input for a random forest (RF) regression model. The RF is used to encode the complex inter-dependencies between thousands of nuclear data features (i.e., sensitivity profiles and aspects describing the measurements) and 875 simulated and experimental k eff values in order to understand what nuclear data features are most informative for predicting bias. The complexity of relationships and high-dimensional space is difficult-to-impossible to search fully using simply expert judgment. As a first proof-of-concept—step, it is demonstrated that this technique is able to correctly trace large discrepancies between simulated and experimental k eff back to fabricated shortcomings in nuclear data that were perturbed to simulated k eff values. In a second, real-case scenario, step, the RF algorithm is used to validate the ENDF/B-VIII.0 library in comparison to ENDF/B-VII.1 nuclear data. One case is showcased where the chosen ML algorithms highlighted nuclear data (the 19 F(n,inl) cross section from 0.4–0.9 MeV) that are shown to be problematic by comparing them to associated differential experimental data and nuclear data from other libraries. In addition to that, it is shown that the RF results point towards poor benchmark experiments and associated underestimated uncertainties (e.g., the PU-SOL-THERM-028 series). However, using the RF algorithm for validating nuclear data with respect to k eff is currently limited to pinpointing groups of questionable nuclear data due to the inherent correlations between features introduced by the nuclear data themselves and how k eff is simulated. Due to this, we recommend that the ML methods presented be used to augment—rather than replace—the expert knowledge of evaluators and validators.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗
DOE OSTI2021

Upgrades to the ion cyclotron emission diagnostic on the DIII-D tokamak

The ion cyclotron emission diagnostic on the DIII-D tokamak comprises seven single-turn loops that measure high-frequency (1–100 MHz) magnetic field fluctuations that are often excited by energetic particles in the plasma. The raw voltage signals induced in the loops in response to these fluctuations travel through a series of cables, isolation transformer DC blocks, low-pass filters, and finally a digitizer before being analyzed in frequency space. The diagnostic has been recently upgraded, most notably to include four additional graphite tile loops and a new eight-channel digitizer. The previous three loops are all on the low-field side of the tokamak. The measurement capabilities of the system have been expanded by the addition of a new horizontally oriented loop on the low-field side, an additional toroidal loop on the low-field side, and two toroidal loops on the high-field side. These loops will be used to provide approximate mode polarization, improved toroidal mode number calculations, and information on modes in inward-shifted plasmas, respectively.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Investigation of magnetic noise from conductive shields in the 10–300 kHz frequency range

Here we present experimental and theoretical investigations of magnetic noise originating from radio-frequency (RF) conductive shields of flat geometry in the inductance-dominated impedance regime below 300 kHz. The measurement is based on a Q-factor determination of a coil that provides a sufficient sensitivity, placed at the position where the shield magnetic noise is measured. The theory is based on calculations of magnetic field and inductance of one or a few flat rings that emulate a conductive shield. The theoretical model is found to be in close agreement with experimental data. It can be used to predict the magnetic noise of a conductive shield with different thicknesses, conductivities, and temperatures at different distances for a wide range of frequencies. Although the model can be generalized for a more arbitrary shield geometry, in its presented form, it can be applied to the magnetic noise predictions when the shield surface curvature is not large. One important conclusion is that the RF conductive shield can generate the magnetic noise much lower than femtotesla, and, thus, it can be used in many precision experiments targeting minute high-frequency magnetic signals, such as detection of magnetic resonance imaging and nuclear quadrupole resonance signals and search for axion dark matter.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Filterscope Techniques for Parasitic Signal Screening

Here, the filterscope diagnostic uses bandpass filters and photomultiplier tubes (PMTs) to detect specific spectral emission lines. A filterscope was used to measure the W I 400.88 nm line emission as a function of ion energy on the Radio Frequency Plasma Interaction Experiment (RF PIE) for the purpose of assessing W erosion on plasma-facing components (PFCs). Different filter techniques are being explored and compared in order to effectively screen out nearby impurity lines, like the Ar II 401.39 nm line. The effectiveness of these techniques is determined by comparing the measurements to a high-resolution 1.0 m Czerny–Turner spectrometer with 0.012 nm spectral resolution. The ability to filter out nearby impurity emissions is useful when imaging PFCs in fusion devices including divertor and antenna guard limiters. Initial results with a helium plasma show little difference between the two techniques at higher bias voltages. In a helium plasma at lower dc bias voltages, a two-filter technique with filters at two separate wavelengths was shown to be more effective at screening out background signals. Data collected with an argon plasma however show the technique with overlapping filters on the line of interest is a closer match to spectrometer data at lower dc bias voltages.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Machine learning-aided line intensity ratio technique applied to deuterium plasmas

It has been demonstrated that the electron density, n e , and temperature, T e , are successfully evaluated from He I line intensity ratios coupled with machine learning (ML). In this paper, the ML-aided line intensity ratio technique is applied to deuterium (D) plasmas with 0.031 < n e (10 18 m –3 ) < 0.67 and 2.3 < T e (eV) < 5.1 in the PISCES-A linear plasma device. Two line intensity ratios, D α /D γ and D α /D β , are used to develop a predictive model for n e and T e separately. Reasonable agreement of both ne and Te with those from single Langmuir probe measurements is obtained at n e > 0.1 × 10 18 m –3 . Addition of the D 2 /D α intensity ratio, where the D 2 band emission intensity is integrated in a wavelength range of λ ~ 557.4–643.0 nm, is found to improve the prediction of, in particular, n e , and T e . It is also confirmed that the technique works for D plasmas with 0.067 < n e (10 18 m –3 ) < 6.1 and 0.8 < T e (eV) < 15 in another linear plasma device, PISCES-RF. The two training datasets from PISCES-A and PISCES-RF are combined, and unified predictive models for n e and T e give reasonable agreement with probe measurements in both devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Design Considerations for Controlling Silicon Nanoparticle Nucleation and Growth in a Nonthermal Plasma

Controlling the nucleation and growth of nanoparticles in low temperature plasma systems is imperative for controlling nanoparticle size distributions; and for some applications such as deposition and etching in microelectronic processing, preventing particle contamination. In this work, silicon nanoparticle (NP) production from silane is used as a model system to investigate the nucleation process. Although the mechanisms responsible for silicon NP nucleation and growth have been studied, it is unclear how controllable system parameters (e.g., pressure, system geometry, and gas composition) can be used to inhibit or promote NP formation. For example, the transport of reactive silane species is expected to significantly affect the feed fraction of silane required to nucleate silicon NP (the nucleation onset fraction) due to losses at the reactor walls. In this work, NP mass density was determined as a function of system pressure, gas composition, and reactor diameter for a tubular flow-through radiofrequency (RF) plasma using Ar/H2/He/SiH4 gas mixtures. A quartz crystal microbalance (QCM) impactor was developed to measure the total aerosol mass density downstream of the plasma and thereby identify the nucleation onset and its dependence on process parameters. Finally, a reaction mechanism was developed and incorporated into a global plasma chemistry model to better understand the nucleation onset and NP growth.

36 MATERIALS SCIENCE↗
DOE OSTI2024

NO formation by N 2 /O 2 plasma catalysis: The impact of surface reactions, gas-phase reactions, and mass transport

Pathways and timescales relevant to facilitate plasma-assisted N 2 -O 2 reactions are assessed by measuring the consumption of plasma-derived N and the formation of NO in the gas phase and over Ag catalytic surfaces. These measurements are enabled by a setup that enables N 2 activation in an atmospheric pressure RF plasma jet, enables O 2 addition in the plasma afterglow, facilitates reactions over an Ag wire catalyst, and allows species density quantification by molecular beam mass spectrometry. Gas-phase reactions consume N but do not form NO with high selectivity. The presence of the non-porous Ag wire catalyst increases the rate of N conversion to NO, though mass transfer processes, not surface reactions, dictate the rate of N consumption. When O 2 concentrations and the ratio of the surface area of the catalyst to the void volume of the reactor are high (3–5 mol% O 2 , 10900 m –1 ), N conversion to NO reaches 100 % selectivity. When both N 2 and O 2 are fed through the plasma jet, gas-phase NO production increases 10×, although plasma and gas-phase processes do not exclusively produce NO. Above a threshold NO density, N cannot diffuse to the catalyst surface faster than it is consumed in the gas phase by reactions with NO. Furthermore, the use of heterogeneous catalysts to enhance plasma-driven N x O y formation and control N x O y product selectivity is limited to cases where diffusive transport of N from the gas phase to the catalyst surface is faster than consumption of N from gas-phase reactions with NO.

Engineering↗
DOE OSTI2025

Frequency dependence of BCS and residual resistance using multi-mode measurement of nitrogen-doped single-cell elliptical cavities

Various cavity surface treatments have been found to significantly improve cavity quality factor, Q0, with one such treatment being nitrogen-doping (N-doping). N-doped 1.3 GHz cavities were the first found to exhibit anti-Q slope, the increase of Q0 with accelerating field, Eacc. However, even with the use of the same N-doping recipes, this anti-Q slope behavior has not been realized in sub-GHz frequency cavities. In this study, we measured the Q0 and surface resistance, RS, of our N-doped, single-cell, elliptical cavity for both the 644 MHz fundamental mode (FM) and 1.45 GHz higher-order mode (HOM). As a result of multi-mode measurements, the BCS and residual resistances, the temperature-dependent and temperature-in-dependent RF surface resistances, could be determined without the influence of cavity-to-cavity surface treatment variations. We will discuss the frequency-dependent behaviors of the BCS and residual resistances.

Accelerator Physics↗
DOE OSTI2025

Study of ponderomotive instability in the FRIB beta=0.53 half-wave resonator

Superconducting radio-frequency niobium cavities are susceptible to deformations caused by external or internal forces, leading to shifts in the cavity resonant frequency. One source of deformation comes from the radiation pressure of the cavity fields, producing the so-called Lorentz force detuning effect. This effect can couple to the cavity mechanical modes in generator driven mode, leading to ponderomotive instability. In the FRIB 322 MHz, β=0.53 Half-wave Resonators (HWR), the instability appeared when the cavity was detuned, with thresholds depending on low-level RF control parameters, such as closed loop gain, as well as accelerating gradient. Using a measured Lorentz Transfer Function, Simulink simulations were conducted to predict the instability thresholds, which were then compared with the experimental results. We will discuss how these thresholds can be broadened to enable stable operation at higher gradients.

Accelerator Physics↗
DOE OSTI2021

Interaction of radio frequency waves with cylindrical density filaments: scattering and radiation pressure

The propagation of radio-frequency (RF) waves in tokamaks can be affected by filamentary structures, or blobs, that are present in the edge plasma and the scrape-off layer. The difference in the permittivity between the surrounding plasma and interior of a filament leads to reflection, refraction and diffraction of the waves. This, in turn, can affect the power flow into the core of the plasma and reduce the efficiency of heating and/or current generation. The scattering of RF waves, lower hybrid, helicon and ion cyclotron waves, by a single cylindrical filament, embedded in a background plasma, is studied using a full-wave analytical theory developed previously (Ram & Hizanidis, Phys. Plasmas , vol. 23, 2016, 022504). The theory assumes that the plasma in and around a filament is homogeneous and cold. A detailed scattering analysis reveals a variety of common features that exist among the three distinctly different RF waves. These common attributes can be inferred intuitively based on an examination of the cold plasma dispersion relation. The physical intuition is a useful step to understanding experimental observations on scattering, as well as results from simulations that include general forms of edge plasma turbulence. While a filament can affect the propagation of RF waves, the radiation force exerted by the waves can influence the filament. The force on a filament is determined using the Maxwell stress tensor. In 1905, Poynting was the first to evaluate and measure the radiation force on an interface separating two different dielectric media (Poynting, London Edinburgh Dublin Philos. Mag. J. Sci. , vol. 9, 1905, pp. 393–406). For ordinary light propagating in vacuum and incident on a glass surface, Poynting noted that the surface is ‘pulled’ towards the vacuum. In a magnetized cold plasma, there are two independent wave modes. Even if only one of these modes is excited by an RF antenna, a filament will couple power to the other mode: a consequence of electromagnetic boundary conditions. This facet of scattering has consequences on the radiation force that go beyond Poynting's seminal contribution. The direction of the force depends on the polarization of the incident wave and on the mode structure of the waves inside and in the vicinity of a filament. It can either pull the filament toward the RF source or push it away. For slow lower hybrid waves, filaments with densities greater than the ambient density are pulled in, while filaments with lower densities are pushed out, thereby enhancing the density in front of the antenna. In the case of fast helicon and ion cyclotron waves, the direction of the force depends on the plasma and wave parameters; in particular, on the ambient density. The radiation force, in all three frequency ranges, is large enough to affect the motion of a filament and could be measured experimentally. This also suggests the possibility of modifying the edge turbulence using RF waves.

Physics↗
DOE OSTI2022

Interaction of radio frequency waves with cylindrical density filaments -- scattering and radiation pressure

The propagation of radio-frequency (RF) waves in tokamaks can be affected by filamentary structures, or blobs, that are present in the edge plasma and the scrape-off layer. The difference in the permittivity between the surrounding plasma and interior of a filament leads to reflection, refraction and diffraction of the waves. This, in turn, can affect the power flow into the core of the plasma and reduce the efficiency of heating and/or current generation. The scattering of RF waves, lower hybrid, helicon and ion cyclotron waves, by a single cylindrical filament, embedded in a background plasma, is studied using a full-wave analytical theory developed previously (Ram & Hizanidis, Phys. Plasmas, vol. 23, 2016, 022504). The theory assumes that the plasma in and around a filament is homogeneous and cold. A detailed scattering analysis reveals a variety of common features that exist among the three distinctly different RF waves. These common attributes can be inferred intuitively based on an examination of the cold plasma dispersion relation. The physical intuition is a useful step to understanding experimental observations on scattering, as well as results from simulations that include general forms of edge plasma turbulence. While a filament can affect the propagation of RF waves, the radiation force exerted by the waves can influence the filament. The force on a filament is determined using the Maxwell stress tensor. In 1905, Poynting was the first to evaluate and measure the radiation force on an interface separating two different dielectric media (Poynting, London Edinburgh Dublin Philos. Mag. J. Sci., vol. 9, 1905, pp. 393–406). For ordinary light propagating in vacuum and incident on a glass surface, Poynting noted that the surface is ‘pulled’ towards the vacuum. In a magnetized cold plasma, there are two independent wave modes. Even if only one of these modes is excited by an RF antenna, a filament will couple power to the other mode: a consequence of electromagnetic boundary conditions. This facet of scattering has consequences on the radiation force that go beyond Poynting's seminal contribution. The direction of the force depends on the polarization of the incident wave and on the mode structure of the waves inside and in the vicinity of a filament. It can either pull the filament toward the RF source or push it away. For slow lower hybrid waves, filaments with densities greater than the ambient density are pulled in, while filaments with lower densities are pushed out, thereby enhancing the density in front of the antenna. In the case of fast helicon and ion cyclotron waves, the direction of the force depends on the plasma and wave parameters; in particular, on the ambient density. The radiation force, in all three frequency ranges, is large enough to affect the motion of a filament and could be measured experimentally. This also suggests the possibility of modifying the edge turbulence using RF waves.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗