Results for “RF modulation” — Page 10

NASA NTRS1972

Analysis of signal to noise enhancement using a highly selective modulation tracking filter

Experiments are reported which utilize photodielectric effects in semiconductor loaded superconducting resonant circuits for suppressing noise in RF communication systems. The superconducting tunable cavity acts as a narrow band tracking filter for detecting conventional RF signals. Analytical techniques were developed which lead to prediction of signal-to-noise improvements. Progress is reported in optimization of the experimental variables. These include improved Q, new semiconductors, improved optics, and simplification of the electronics. Information bearing signals were passed through the system, and noise was introduced into the computer model.

Haden, C. R.↗

NASA NTRS1984

Radio-Frequency and Wideband Modulation Arraying

Summing network receives coherent signals from all receivers in array. Method sums narrow-band radio-frequency (RF) carrier powers and wide-band spectrum powers of array of separate antenna/receiver systems designed for phase-locked-loop or suppressed-carrier operation.

Brockman, M. H.↗

NASA NTRS1996

The Advanced Communication Technology Satellite and ISDN

This paper depicts the Advanced Communication Technology Satellite (ACTS) system as a global central office switch. The ground portion of the system is the collection of earth stations or T1-VSAT's (T1 very small aperture terminals). The control software for the T1-VSAT's resides in a single CPU. The software consists of two modules, the modem manager and the call manager. The modem manager (MM) controls the RF modem portion of the T1-VSAT. It processes the orderwires from the satellite or from signaling generated by the call manager (CM). The CM controls the Recom Laboratories MSPs by receiving signaling messages from the stacked MSP shelves ro units and sending appropriate setup commands to them. There are two methods used to setup and process calls in the CM; first by dialing up a circuit using a standard telephone handset or, secondly by using an external processor connected to the CPU's second COM port, by sending and receiving signaling orderwires. It is the use of the external processor which permits the ISDN (Integrated Services Digital Network) Signaling Processor to implement ISDN calls. In August 1993, the initial testing of the ISDN Signaling Processor was carried out at ACTS System Test at Lockheed Marietta, Princeton, NJ using the spacecraft in its test configuration on the ground.

Lowry, Peter A.↗

NASA NTRS1997

Poling of Microwave Electro-Optic Devices

The desire to transmit high frequency, microwave RF signals over fiber optic cables has necessitated the need for electro-optic modulation devices. However, in order to reap these potential benefits, it is necessary to develop the devices and their associated fabrication processes, particularly those processes associated with the poling of the devices. To this end, we entered into a cooperative research agreement with Richard Kunath of NASA LeRC. A graduate student in my group, Tony Kowalczyk, worked closely with the group at NASA to develop processes for construction of a microwave frequency electro-optic modulator. Materials were commercially obtained from Amoco Chemical and in collaboration with Lockheed-Martin. The photolithography processes were developed at NASA LeRC and the electric-field poling process was carried out in our laboratory at CWRU. During the grant period, the poling process conditions were investigated for these multilayer devices. Samples were poled and the resulting nonlinear optical properties were evaluated in our laboratory. Following the grant period, Kowalczyk went to NASA under a NRC fellowship, and I continued to collaborate as a consultant. Publications listed at the end of this report came out of this work. Another manuscript is in preparation and will be submitted shortly.

Singer, Kenneth D.↗

NASA NTRS2008

Hardware Architecture Study for NASA's Space Software Defined Radios

This study defines a hardware architecture approach for software defined radios to enable commonality among NASA space missions. The architecture accommodates a range of reconfigurable processing technologies including general purpose processors, digital signal processors, field programmable gate arrays (FPGAs), and application-specific integrated circuits (ASICs) in addition to flexible and tunable radio frequency (RF) front-ends to satisfy varying mission requirements. The hardware architecture consists of modules, radio functions, and and interfaces. The modules are a logical division of common radio functions that comprise a typical communication radio. This paper describes the architecture details, module definitions, and the typical functions on each module as well as the module interfaces. Trade-offs between component-based, custom architecture and a functional-based, open architecture are described. The architecture does not specify the internal physical implementation within each module, nor does the architecture mandate the standards or ratings of the hardware used to construct the radios.

Reinhart, Richard C.↗

NASA NTRS1981

Four- and five-layer silicon-clad dielectric waveguides

Computer modeling studies conducted on four-layer silicon-clad dielectric waveguides indicate that the attenuation (alpha) and mode index (beta/K) behave as exponentially damped sinusoids as the silicon thickness is increased. The observed effect can be explained quite simply as a periodic coupling between the guided modes of the lossless structure and the lossy modes supported by the high-refractive index silicon. The attenuation and mode index are significantly altered by conductivity changes in the silicon; an amplitude modulator and an intensity modulator were proposed using these results. Predicted high attenuations in the device may be reduced significantly with a silicon dioxide buffer layer between the semiconductor and the polystyrene guide. Experimental confirmation of the predicted characteristics is still necessary. A number of thin-silicon film waveguides have been RF sputtered but attenuation measurements to verify the damped oscillatory behavior are forthcoming. Conductivity variations of the silicon should demonstrate the modulation capabilities.

Mcwright, G.↗

NASA NTRS2001

Helicopter Rotor Antenna

This effort was directed toward demonstration of the efficacy of a concept for mitigation of the rotor blade modulation problem in helicopter communications. An antenna is envisioned with radiating elements mounted on the rotor and rotating with it. The rf signals are coupled to the radio stationary with respect to the airframe via a coupler of unique design. The coupler has an rf cavity within which a mode is established and the field distribution of this mode is sampled by probes rotating with the radiating elements. In this manner the radiated pattern is "despun" with respect to the rotor. Theoretical analysis has indicated that this arrangement will be less susceptible to rotor blade modulation that would be a conventional fixed mounted antenna. A small coupler operating at S-band was designed, fabricated, and mounted on a mockup representative of a helicopter body. A small electric motor was installed to rotate the rotor portion of the coupler along with a set of radiating elements during testing. This test article was be evaluated using the JPL Mesa Antenna Measurement Facility to establish its ability to mitigate rotor blade modulation. It was found that indeed such a coupler will result in a despun pattern and that such a pattern can be effective in mitigation of rotor blade modulation.

Pogorzelski, Ronald J.↗

NASA NTRS1972

A superconducting time-variant filtering system.

Description of a laboratory test facility for studying the tracking capabilities of a superconducting time-varying filter system. An RF signal from an antenna is amplified and fed to a mixer; the IF signal modulates an optical diode, and the emitted light is directed through an optical system onto a high-purity high-resistance semiconductor terminating a quarter-wavelength stub in a lead-plated superconducting cavity. The resulting perturbation in the cavity resonant frequency is proportional to the signal modulation present in the light beam. The narrow-band superconducting cavity is thereby acting as a time-variant filter that tracks the instantaneous signal modulation. SNR improvement on the order of 25 dB can be obtained due to the noise rejection characteristics of such a modulation tracking filter.

Arndt, G. D.↗

NASA NTRS1977

On-orbit performance of the 12 GHz, 200 watt transmitter experiment package for CTS

Performance characteristics from on-orbit tests of the transmitter experiment package (TEP) for the Communications Technology Satellite (CTS) are presented. The TEP consists of a power processing system (PPS), an output stage tube (OST) and a variable conductance heat pipe system (VCHPS), all of which are described. Test results presented include efficiencies, RF output power, frequency response, and performance with single and multiple (two) carriers, frequency-modulated by video signals.

Alexovich, R. E.↗

NASA NTRS1977

On-orbit performance of the 12 GHz, 200 watt transmitter experiment package for CTS

Performance characteristics from on-orbit tests of the Transmitter Experiment Package (TEP) for the Communications Technology Satellite (CTS) are presented. The TEP consists of a Power Processing System (PPS), an Output Stage Tube (OST), and a Variable Conductance Heat Pipe System (VCHPS), all of which are described. The OST is a coupled-cavity traveling-wave tube with a multistage depressed collector and a stepped velocity-tapered slow-wave structure for efficiency enhancement. It has an RF output power of 240 W and an overall efficiency of 51.5% at a center band frequency of 12.080 GHz. The PPS provides the required operating voltages, regulation, control, and protection for the OST. It has a measured dc-dc conversion efficiency of 86.5% to 88.5%. The VCHPS consists of a fin radiator and three dual-artery stainless steel heat pipes using methanol and a mixture of inert gases. Test results presented include efficiencies, RF output power, frequency response, and performance with single and multiple (two) carriers frequency-modulated by video signals.

Alexovich, R. E.↗

NASA NTRS1979

Results of thin-route satellite communication system analyses including estimated service costs

Ways for determining optimum satellite and terrestrial system architectures and parameters for providing the most economical telephone service to remote areas of the U.S. are explored. Several configurations for an isolated rural telephone system, covering all the states plus Alaska, employing satellites is considered. Both direct-to-the-user and community-type of systems are evaluated using UHF and Ku-band RF equipment for the rural/satellite links. The effect of multiple spot beams, outage, signal quality, modulation method, satellite accessing, forward error correction, and the number of users are also evaluated. The total cost for a 5-minute call from an isolated rural user to a TELCO user was shown to be as low as $1.30 for a system with 1.8 X 10 to the sixth rural users.

Wright, D. L.↗

NASA NTRS2011

Peak Satellite-to-Earth Data Rates Derived From Measurements of a 20 Gbps Bread-Board Modem

A prototype data link using a Ka-band space qualified, high efficiency 200 W TWT amplifier and a bread-board modem emulator were created to explore the feasibility of very high speed communications in satellite-to-earth applications. Experiments were conducted using a DVB-S2-like waveform with modifications to support up to 20 Gbps through the addition of 128-Quadrature Amplitude Modulation (QAM). Limited by the bandwidth of the amplifier, a constant peak symbol rate of 3.2 Giga-symbols/sec was selected and the modulation order was varied to explore what peak data rate might be supported by an RF link through this amplifier. Using 128-QAM, an implementation loss of 3 dB was observed at 20 Gbps, and the loss decreased as data rate or bandwidth were reduced. Building on this measured data, realistic link budget calculations were completed. Low-Earth orbit (LEO) missions based on this TWTA with reasonable hardware assumptions and antenna sizing are found to be bandwidth-limited, rather than power-limited, making the spectral efficiency of 9/10-rate encoded 128-QAM very attractive. Assuming a bandwidth allocation of 1 GHz, these computations indicate that low-Earth orbit vehicles could achieve data rates up to 5 Gbps-an order of magnitude beyond the current state-of-practice, yet still within the processing power of a current FPGA-based software-defined modem. The measured performance results and a description of the experimental setup are presented to support these conclusions.

Landon, David G.↗

NASA NTRS2012

Low-Cost Telemetry System for Small/Micro Satellites

A Software Defined Radio (SDR) concept uses a minimum amount of analog/radio frequency components to up/downconvert the RF signal to/from a digital format. Once in the digital domain, all other processing (filtering, modulation, demodulation, etc.) is done in software. The project will leverage existing designs and enhance capabilities in the commercial sector to provide a path to a radiation-hardened SDR transponder. The SDR transponder would incorporate baseline technologies dealing with improved Forward Error Correcting (FEC) codes to be deployed to all Near Earth Network (NEN) ground stations. By incorporating this FEC, at least a tenfold increase in data throughput can be achieved. A family of transponder products can be implemented using common platform architecture, allowing new products to be more quickly introduced into the market. Software can be reused across products, reducing software/hardware costs dramatically. New features and capabilities, such as encoding and decoding algorithms, filters, and bit synchronizers, can be added to the existing infrastructure without requiring major new capital expenditures, allowing implementation of advanced features in the communication systems. As new telecommunication technologies emerge, incorporating them into the SDR fabric will be easily accomplished with little or no requirements for new hardware. There are no preferred flight platforms for the SDR technology, so it can be used on any type of orbital or sub-orbital platform, all within a fully radiation hardened design.

Sims, William↗

NASA NTRSDate not supplied

The Ejectable Data Recorder: A Lean, Risk-Informed Approach for Hardware Development

NASA is developing the Orion spacecraft to transport crew from the Earth to the Moon as part of the Artemis series of missions. To provide a crew escape capability from pre-launch through ascent, the Orion vehicle is equipped with a Launch Abort System (LAS), built by Lockheed Martin, which pulls the capsule away from the launch vehicle in the event of an abort scenario. The Ascent Abort 2 (AA-2) test flight occurred on July 2, 2019,and tested a production version of the LAS to ensure that it can operate as intended, and to collect a large data set from hundreds of sensors on the vehicle to support Orion flight certification. In the original AA-2 architecture, a single-string set of communications antennas on the LAS would downlink all of the in-flight test data to ground stations. However, that communications architecture was predicted to have data dropouts during abort and jettison of the LAS, and would not support data transmission at all after LAS jettison. As a result, a comprehensive trade study was completed, yielding the addition of antennas on the crew module (CM), a buffer/rebroadcast capability for key portions of the flight, and an ejectable data recorder (EDR) subsystem. This EDR subsystem would serve as a backup to the radio frequency (RF) communications system, and would be non-flight critical, providing a unique capability that enabled management to take a different approach with the hardware and software development. The Crew Module and Separation Ring were developed as “Class 1”Flight Hardware, albeit with some tailoring approaches to enable efficiencies. The Class 1 designation requires full rigor for flight hardware and software, documenting everything that happens to a piece of hardware from procurement through disposal, requiring a full spectrum of acceptance tests, and the highest rigor of quality assurance processes. At the other end of the spectrum, Class 3hardware is controlled, but not intended for flight, and leaves the level of rigor up to the project manager. This classification is often used for research and development projects. Similarly,Class-1E has been recently defined at NASA for ISS payloads and technology development projects that are not flight critical and do not need the full rigor of Class 1 to be successful. The EDR subsystem was challenged at commencement to adopt a skunkworks and agile-like approach to hardware development, allowing for a different risk posture than the rest of the AA-2 hardware. After initially pursuing Class 1 processes, the EDR subsystem design evolved to incorporating numerous commercial components, leading to re-designation as a Class-1E subsystem. The resulting EDR subsystem was fully successful in meeting all flight system requirements, and achieved 100% retrieval of flight test data. This paper will discuss the risk posture of the EDR subsystem and the subsequent tailoring that was enacted as part of its Class-1E status.

EDR↗

NASA NTRS2007

High-Capacity Communications from Martian Distances

High capacity communications from Martian distances, required for the envisioned human exploration and desirable for data-intensive science missions, is challenging. NASA s Deep Space Network currently requires large antennas to close RF telemetry links operating at kilobit-per-second data rates. To accommodate higher rate communications, NASA is considering means to achieve greater effective aperture at its ground stations. This report, focusing on the return link from Mars to Earth, demonstrates that without excessive research and development expenditure, operational Mars-to-Earth RF communications systems can achieve data rates up to 1 Gbps by 2020 using technology that today is at technology readiness level (TRL) 4-5. Advanced technology to achieve the needed increase in spacecraft power and transmit aperture is feasible at an only moderate increase in spacecraft mass and technology risk. In addition, both power-efficient, near-capacity coding and modulation and greater aperture from the DSN array will be required. In accord with these results and conclusions, investment in the following technologies is recommended:(1) lightweight (1 kg/sq m density) spacecraft antenna systems; (2) a Ka-band receive ground array consisting of relatively small (10-15 m) antennas; (3) coding and modulation technology that reduces spacecraft power by at least 3 dB; and (4) efficient generation of kilowatt-level spacecraft RF power.

Williams, W. Dan↗

NASA NTRS2023

Flexible User Radio for Lunar Missions

NASA’s Artemis program and other lunar exploration and development programs are planning over 40 lunar missions before 2030. Lunar missions, both crewed and uncrewed, include orbiters, landers, rovers, and surface stations. All these missions require communications with Earth, either via Direct to Earth (DTE) links or through relays in lunar orbit. Multiple DTE options are available among existing and planned ground stations: Deep Space Network (DSN), European Space Agency, and others. Relay options include the planned Lunar Gateway, LunaNet compliant relays, and some lunar landers propose to launch dedicated orbiters. The dilemma for lunar system designers is to identify a communication link which meets mission requirements but does not have issues of limited access (e.g. DSN is in high demand supporting deep space missions with high priority and some with inflexible schedules), system impacts (high power Radio Frequency (RF) for DTE links), cost (dedicated relay), or operational date. To avoid this difficult decision, a Flexible Radio for Lunar Missions is proposed, which will enable system designs to proceed prior to any final decision on the communication network to be used, by enabling compatibility with any of multiple DTE or orbital relay communication systems. The Flexible Radio will support the necessary frequency, bandwidth, modulation, and power requirements to interoperate with the majority of known or planned DTE or relay systems, and can be designed into a lunar mission without prior knowledge of which link will ultimately be used. Furthermore, the link being used can be changed as needed during the mission, in near real time. The Flexible Radio design will leverage work already completed at NASA in the areas of Wideband RF, Software Defined Radio, Adaptive Coding and Modulation, and Phased Array antennas. The Flexible Radio requires sufficient bandwidth to cover the allocated frequencies for both the operation of links in cislunar space and for space-to-Earth links; the flexibility to support multiple modulations, data rates, and coding schemes; the ability to identify available relays, detect and recognize the signals of those relays, and adapt its own frequency, modulation, symbol rate, and code rate to operate with the detected relay (or DTE station); and finally, it requires appropriate software to support network configuration and interoperability with the detected network. The Flexible Radio can be designed in a sufficiently small, lightweight, and low-power package to be used in a wide variety of lunar systems. The initial implementation, as proposed, will focus on the Ka-band, supporting up to 2 GHz bandwidth around the 27 GHz frequency for return links, and 23 GHz for forward links. Other frequency bands are under consideration for future configurations. The software defined modem will support OQPSK, BPSK, and NASA-defined modulations which also support two-way ranging with data. For near-real time adaptation, the Flexible Radio will scan the sky for available relays, using a phased array antenna with Adaptive/Cognitive Communications. It will then configure for network interoperability supporting DTN and other protocol options. The Flexible Radio will support scheduled connections and on-demand use when available.

Lunar Space Communications↗

NASA NTRSDate not supplied

Flexible User Radio for Lunar Missions

NASA’s Artemis program and other lunar exploration and development programs are planning over 40 lunar missions before 2030. Lunar missions, both crewed and uncrewed, include orbiters, landers, rovers, and surface stations. All these missions require communications with Earth, either via Direct to Earth (DTE) links or through relays in lunar orbit. Multiple DTE options are available among existing and planned ground stations: Deep Space Network (DSN), European Space Agency, and others. Relay options include the planned Lunar Gateway, LunaNet compliant relays, and some lunar landers propose to launch dedicated orbiters. The dilemma for lunar system designers is to identify a communication link which meets mission requirements but does not have issues of limited access (e.g. DSN is in high demand supporting deep space missions with high priority and some with inflexible schedules), system impacts (high power Radio Frequency (RF) for DTE links), cost (dedicated relay), or operational date. To avoid this difficult decision, a Flexible Radio for Lunar Missions is proposed, which will enable system designs to proceed prior to any final decision on the communication network to be used, by enabling compatibility with any of multiple DTE or orbital relay communication systems. The Flexible Radio will support the necessary frequency, bandwidth, modulation, and power requirements to interoperate with the majority of known or planned DTE or relay systems, and can be designed into a lunar mission without prior knowledge of which link will ultimately be used. Furthermore, the link being used can be changed as needed during the mission, in near real time. The Flexible Radio design will leverage work already completed at NASA in the areas of Wideband RF, Software Defined Radio, Adaptive Coding and Modulation, and Phased Array antennas. The Flexible Radio requires sufficient bandwidth to cover the allocated frequencies for both the operation of links in cislunar space and for space-to-Earth links; the flexibility to support multiple modulations, data rates, and coding schemes; the ability to identify available relays, detect and recognize the signals of those relays, and adapt its own frequency, modulation, symbol rate, and code rate to operate with the detected relay (or DTE station); and finally, it requires appropriate software to support network configuration and interoperability with the detected network. The Flexible Radio can be designed in a sufficiently small, lightweight, and low-power package to be used in a wide variety of lunar systems. The initial implementation, as proposed, will focus on the Ka-band, supporting up to 2 GHz bandwidth around the 27 GHz frequency for return links, and 23 GHz for forward links. Other frequency bands are under consideration for future configurations. The software defined modem will support OQPSK, BPSK, and NASA-defined modulations which also support two-way ranging with data. For near-real time adaptation, the Flexible Radio will scan the sky for available relays, using a phased array antenna with Adaptive/Cognitive Communications. It will then configure for network interoperability supporting DTN and other protocol options. The Flexible Radio will support scheduled connections and on-demand use when available.

Lunar Space Communications↗

NASA NTRS2003

Packaging Considerations for Integrated RF Microphotonic Receiver at Ka-Band

The NASA Computing, Information and Communications Technology (CICT) Program is supporting the development of an RF microphotonic Ka-band receiver. The receiver consists of a lithium niobate micro-disk that enables the incoming RF signal (up to Ka-band) to be coupled to the optical signal (approx. 200 THz). The modulated optical signal is detected by the high-speed photonic signal processing electronics. When compared with an all-electronic approach, the microphotonic receiver technology offers 1 Ox smaller volume, smaller weight, and smaller power consumption, greater sensitivity, and optical isolation for applications in extreme environments. It could potentially be implemented to support planetary surface-to-surface and surface-to-relay communications, as well as high-data-rate inter-satellite links. We are currently studying a number of fabrication and integration issues that could result as this technology is advanced for potential insertion into a NASA mission. The results of our preliminary effort to integrate the RF microphotonic receiver components (e.g., the lithium niobate micro-disk, the optical elements, and the Ka-band patch antenna) on an etched silicon wafer will be presented, In addition, the concomitant integration and packaging issues, and the potential NASA applications will be discussed.

Nguyen, Hung↗