Search NASA⌕ Search

SEARCH · Search NASA

Results for “ROLLING CONTACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

The International Space Station Solar Alpha Rotary Joint Anomaly Investigation

The Solar Alpha Rotary Joint (SARJ) is a single-axis pointing mechanism used to orient the solar power generating arrays relative to the sun for the International Space Station (ISS). Approximately 83 days after its on-orbit installation, one of the two SARJ mechanisms aboard the ISS began to exhibit high drive motor current draw. Increased structural vibrations near the joint were also observed. Subsequent inspections via Extravehicular Activity (EVA) discovered that the nitrided case hardened steel bearing race on the outboard side of the joint had extensive damage to one of its three rolling surfaces. A far-reaching investigation of the anomaly was undertaken. The investigation included metallurgical inspections, coupon tests, traction kinematics tests, detailed bearing measurements, and thermal and structural analyses. The results of the investigation showed that anomaly had most probably been caused by high bearing edge stresses that resulted from inadequate lubrication of the rolling contact. The profile of the roller bearings and the metallurgical properties of the race ring were also found to be significant contributing factors. To mitigate the impact of the damage astronauts cleaned and lubricated the race ring surface with grease. This corrective action led to significantly improved performance of the mechanism both in terms of drive motor current and induced structural vibration.

Harik, Elliot P.↗
NASA NTRS2010

The International Space Station Solar Alpha Rotary Joint Anomaly Investigation

The Solar Alpha Rotary Joint (SARJ) is a single-axis pointing mechanism used to orient the solar power generating arrays relative to the sun for the International Space Station (ISS). Approximately 83 days after its on-orbit installation, one of the two SARJ mechanisms aboard the ISS began to exhibit high drive motor current draw. Increased structural vibrations near the joint were also observed. Subsequent inspections via Extravehicular Activity (EVA) discovered that the nitrided case-hardened steel bearing race on the outboard side of the joint had extensive damage to one of its three rolling surfaces. A farreaching investigation of the anomaly was undertaken. The investigation included metallurgical inspections, coupon tests, traction kinematics tests, detailed bearing measurements, and thermal and structural analyses. The results of the investigation showed that the anomaly had most probably been caused by high bearing edge stresses that resulted from inadequate lubrication of the rolling contact. The profile of the roller bearings and the metallurgical properties of the race ring were also found to be significant contributing factors. To mitigate the impact of the damage, astronauts cleaned and lubricated the race ring surface with grease. This corrective action led to significantly improved performance of the mechanism both in terms of drive motor current and induced structural vibration.

Harik, Elliot P.↗
NASA NTRS2011

Effect of Test Environment on Lifetime of Two Vacuum Lubricants Determined by Spiral Orbit Tribometry

The destruction rates of a perfluoropolyether (PFPE) lubricant, Krytox 143AC, subjected to rolling contact with 440C steel in a spiral orbit tribometer at room temperature have been evaluated as a function of test environment. The rates in ultrahigh vacuum, 0.213 kPa (1.6 torr) oxygen and one atmosphere of dry nitrogen were about the same. Water vapor in the test environment-a few ppm in one atmosphere of nitrogen-reduced the destruction rate by up to an order of magnitude. A similar effect of water vapor was found for the destruction rate of Pennzane 2001A, an unformulated multiply alkylated cyclopentane (MAC) hydrocarbon oil.

Pepper, Stephen V.↗
NASA NTRS2014

Reducing Wear of Steel Rolling Against Ti6Al4V Operating in Vacuum

This work was motivated by a qualification test of a mechanism for a space telescope. During the test undesired wear debris was formed. In this project alterative materials and coatings were tested with intent to reduce wear and debris when steel has a misaligned rolling contact against Ti6Al4V. Testing was done using a vacuum roller rig mimicking the mechanism's contact conditions. Ten configurations were tested. Most configurations resulted in significant debris. A sputtered 1-micrometer-thick nan-ocomposite molybdenum disulfide (MoS2) film provided the best wear protection. The best configuration made use of the MoS2 coating on both materials, and in preparing for sputtering the anodized Ti6Al4V working surface was smoothed using an ultrasonic process.

Krantz, Timothy L.↗
NASA NTRS2014

A Study on the Effects of Ball Defects on the Fatigue Life in Hybrid Bearings

Hybrid ball bearings using silicon nitride ceramic balls with steel rings are increasingly being used in space mechanism applications due to their high wear resistance and long rolling contact fatigue life. However, qualitative and quantitative reports of the effects of ball defects that cause early fatigue failure are rare. We report on our approach to study these effects. Our strategy includes characterization of defects encountered in use, generation of similar defects in a laboratory setting, execution of full-scale bearing tests to obtain lifetimes, post-test characterization, and related finite-element modeling to understand the stress concentration of these defects. We have confirmed that at least one type of defect of appropriate size can significantly reduce fatigue life. Our method can be used to evaluate other defects as they occur or are encountered.

Tang, Ching-Yao↗
NASA NTRSDate not supplied

Tribological Prospects and Progress for NiTi Bearings for Aerospace Applications

Rolling element and sliding bearings made from dimensionally stable, nickel-rich NiTi alloys have been successfully manufactured, tested and applied in several different aerospace applications. In this presentation, the development history and material properties of NiTi alloys is reviewed and its behavior in sliding and rolling contacts is examined. Key material characteristics such as superelasticity and fracture toughness and their effects on bearing applications are considered. With proper application engineering, it is shown that NiTi bearings can resolve longstanding and persistent bearing problems related to heavy loads and operation in corrosive and debris contaminated environments.

Bearings↗
DOE OSTI2013

Long-Term Probability Distribution of Wind Turbine Planetary Bearing Loads (Poster)

Among the various causes of bearing damage and failure, metal fatigue of the rolling contact surface is the dominant failure mechanism. The fatigue life is associated with the load conditions under which wind turbines operate in the field. Therefore, it is important to understand the long-term distribution of the bearing loads under various environmental conditions. The National Renewable Energy Laboratory's 750-kW Gearbox Reliability Collaborative wind turbine is studied in this work. A decoupled analysis using several computer codes is carried out. The global aero-elastic simulations are performed using HAWC2. The time series of the drivetrain loads and motions from the global dynamic analysis are fed to a drivetrain model in SIMPACK. The time-varying internal pressure distribution along the raceway is obtained analytically. A series of probability distribution functions are then used to fit the long-term statistical distribution at different locations along raceways. The long-term distribution of the bearing raceway loads are estimated under different environmental conditions. Finally, the bearing fatigue lives are calculated.

17 WIND ENERGY↗
DOE OSTI2021

Why does a phosphonium-phosphinate ionic liquid protect the contact surfaces from wear and micropitting but increase vibration when used as an additive in rolling-sliding lubrication?

A phosphonium-phosphinate ionic liquid (IL) was studied as a lubricant additive for rolling-sliding contacts. The bench-scale test was designed to simulate automotive rear axle operation during cold start, highway towing, and overload conditions. Adding such an IL (2%) into a base oil significantly reduced wear loss and rolling contact fatigue, e.g., microcracking and micropitting, but made the vibrational noise notably higher under a low (-1.5%) sliding roll ratio (SRR). Additionally, worn surface characterization revealed an interesting texture pattern with alternating smoother plateaus and rougher valleys, which is believed to cause the high vibration. No increased vibration was observed at a high (-30%) SRR, possibly because the more aggressive sliding abrasion prevented such a surface texture from forming.

36 MATERIALS SCIENCE↗
NASA NTRS1980

A film thickness analysis for line contacts under pure rolling conditions with a non-Newtonian rheological model

The non-Newtonian constitutive equation of Winer and Bair (1979) is applied to a conventional isothermal film thickness analysis of line contact lubrication of rolling elements providing dimensionless film thickness equations for four lubrication methods. The equations can be applied to high viscosity and rolling speed and low limiting shear stress cases where Newtonian methods are not applicable. This analysis is based on a reasonable range of limiting shear stress which is smaller than the Newtonian values for low viscosity lubricants.

Gecim, B.↗
NASA NTRS1984

Hydrodynamic lubrication of rigid nonconformal contacts in combined rolling and normal motion

A numerical solution to the problem of hydrodynamic lubrication of rigid point contacts with an isoviscous, incompressible lubricant was obtained. The hydrodynamic load-carrying capacity under unsteady (or dynamic) conditions arising from the combined effects of squeeze motion superposed upon the entraining motion was determined for both normal approach and separation. Superposed normal motion considerably increases net load-carrying capacity during normal approach and substantially reduces net load-carrying capacity during separation. Geometry was also found to have a significant influence on the dynamic load-carrying capacity. The ratio of dynamic to steady state load-carrying capacity increases with increasing geometry parameter for normal approach and decreases during separation. The cavitation (film rupture) boundary is also influenced significantly by the normal motion, moving downstream during approach and upstream during separation. For sufficiently high normal separation velocity the rupture boundary may even move upstream of the minimum-film-thickness position. Sixty-three cases were used to derive a functional relationship for the ratio of the dynamic to steady state load-carrying capacity in terms of the dimensionless normal velocity parameter (incorporating normal velocity, entraining velocity, and film thickness) and the geometry parameter.

Ghosh, M. K.↗
NASA NTRS1985

Hydrodynamic lubrication of rigid nonconformal contacts in combined rolling and normal motion

A numerical solution to the problem of hydrodynamic lubrication of rigid point contacts with an isoviscous, incompressible lubricant was obtained. The hydrodynamic load-carrying capacity under unsteady (or dynamic) conditions arising from the combined effects of squeeze motion superposed upon the entraining motion was determined for both normal approach and separation. Superposed normal motion considerably increases net load-carrying capacity during normal approach and substantially reduces net load-carrying capacity during separation. Geometry was also found to have a significant influence on the dynamic load-carrying capacity. The ratio of dynamic to steady state load-carrying capacity increases with increasing geometry parameter for normal approach and decreases during separation. The cavitation (film rupture) boundary is also influenced significantly by the normal motion, moving downstream during approach and upstream during separation. For sufficiently high normal separation velocity the rupture boundary may even move upstream of the minimum-film-thickness position. Sixty-three cases were used to derive a functional relationship for the ratio of the dynamic to steady state load-carrying capacity in terms of the dimensionless normal velocity parameter (incorporating normal velocity, entraining velocity, and film thickness) and the geometry parameter.

Ghosh, M. K.↗
NASA NTRS1985

Constitutive modelling of lubricants in concentrated contacts at high slide to roll ratios

A constitutive lubricant friction model for rolling/sliding concentrated contacts such as gears and cams was developed, based upon the Johnson and Tevaarwerk fluid rheology model developed earlier. The friction model reported herein differs from the earlier rheological models in that very large slide to roll ratios can now be accommodated by modifying the thermal response of the model. Also the elastic response of the fluid has been omitted from the model, thereby making it much simpler for use in the high slide to roll contacts. The effects of this simplification are very minimal on the outcome of the predicted friction losses (less than 1%). In essence then the lubricant friction model developed for the high slide to roll ratios treats the fluid in the concentrated contact as consisting of a nonlinear viscous element that is pressure, temperature, and strain rate dependent in its shear response. The fluid rheological constants required for the prediction of the friction losses at different contact conditions are obtained by traction measurements on several of the currently used gear lubricants. An example calculation, using this model and the fluid parameters obtained from the experiments, shows that it correctly predicts trends and magnitude of gear mesh losses measured elsewhere for the same fluids tested here.

Tevaarwerk, J. L.↗
NASA NTRS1978

Surface temperature measurements in rolling and sliding EHD contacts

In this study, moving surface temperature measurements in rolling and sliding EHD point contacts were made using an available infrared technique. Film thickness and traction have also been measured. Slide-to-roll ratios of -2 to +2 have been studied. By using a different kinematic configuration, stationary surface temperatures have also been measured. It has been shown that, while surface temperature rises in the low slip region are relatively small, stationary surface temperatures are significantly higher than the moving surface temperatures. Flash temperature theory has been extended to cover the combined rolling and sliding conditions. Correlation between the predicted and the measured values has also been performed.

Nagaraj, H. S.↗
DOE OSTI2020

Oil miscible phosphonium-phosphate ionic liquid as novel antiwear and antipitting additive for low-viscosity rear axle lubricants

Here we explored the feasibility of using a phosphonium phosphate ionic liquid as a candidate anti-wear and anti-pitting additive for rear axle lubricant. This particular IL was first added to a VHVI8 base oil at 2–3% concentration and demonstrated effective surface protection for wear and micro-cracking under rolling-sliding contacts. The promising results directed to a step further to produce a series of IL-containing low-viscosity (about a half of SAE 75W-90) fully formulated gear oils. Selected IL-containing experimental oils showed superior mitigation of rolling contact fatigue to a commercial SAE 75W-90 gear oil in bench-scale rolling-sliding tests. Full-scale hub dynamometer tests were then conducted and demonstrated more than 3% power output and torque generation for an IL-containing low-viscosity gear oil benchmarked against commercial baselines.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Electrically-Assisted Tubing Processes for Enhancing Manufacturability of Oxide Dispersion Strengthened Structural Materials for Nuclear Reactor Applications

The overall goal of this project is to enhance the formability of Nanostructured Ferritic Alloys (NFAs) such that high-strength thin-walled claddings can be successfully and economically manufactured for use in future nuclear reactors. Specifically, four objectives were identified: Objective #1 – to achieve a good understanding of the mechanical behavior and resulting microstructure of 14YWT made from the powder form subjected to various Electrically- Assisted (EA) loading conditions. Objective #2 – to conduct EA-flat rolling of 14YWT completed and the prioritization/selection of two alternative designs of EA tube rolling processes. Objective #3 – to design and assemble a new EA tube rolling machine. Objective #4 – to conduct rolling using the new EA rolling machine. The above objectives were achieved and the findings can be further applied to establish other innovative fabrication processes. Specifically, the major accomplishments are summarized as: The use of an EA forming process was investigated to reduce the forming force of ODS ferritic steels. The effect of a continuous electric current on 14YWT during plastic deformation was evaluated. EA uniaxial tension tests show that the electric current is able to reduce the flow stress of 14YWT. 14YWT exhibits a ductility minimum at a current density of 34.5 A/mm2 which is consistent with fractography results. Hardness measurements and TEM results indicate that oxide particles are stable during the EA process. By following the tests, microstructure analysis was performed on the sample in its as-received state and after current treatment. The microstructures are stable when subjected to high current density. The related thermal model was developed to predict the Joule heating temperatures. The temperatures were compared with the experimental results. At last, a temperature-dependent hardening model was used to explore the mechanisms acting during EA deformation. Since the model can accurately predict the yield strength of 14YWT under EA conditions without the incorporation of non-thermal effects, it can be concluded that the reduction in yield strength is due to the Joule heating generated under continuous current loading conditions. An oven-heated pure thermal tension test was conducted to confirm this conclusion. The new EA tube rolling machine has been completely developed. The related work includes: (1) forming process design; (2) analysis of the effect of roll-tube contact geometry on rolling force; (3) analysis of machine performance under mechanical loading; (4) design of machine electrical setting path and insulation; (5) multi-pass process analysis; (6) design of power transmission system (axial/radial/torque feeding mechanisms), roll bearing system, cooling system, workpiece feeding mechanism, and other related mechanical connection support components; (7) design and optimization of roll profiles/dimensions; (8) analysis and simulation of the rolling process; (9) development of engineering drawings and fabrication; (10) assembly and calibration of the EA tube rolling machine; (11) design and integration of the electrical control system; (12) hardware integration for high power supply electrically-assisted rolling process; (13) induction heating system integration; (14) experimental tests for the new rolling process. Through the process from conceptual design to final machine calibration and experimental tests, there are many technical and physical works that have been implemented and improved for the best performance of the innovative prototype.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗