SEARCH · Search NASA

Results for “Reduced Order Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Singular perturbation analysis of AOTV-related trajectory optimization problems

The problem of real time guidance and optimal control of Aeroassisted Orbit Transfer Vehicles (AOTV's) was addressed using singular perturbation theory as an underlying method of analysis. Trajectories were optimized with the objective of minimum energy expenditure in the atmospheric phase of the maneuver. Two major problem areas were addressed: optimal reentry, and synergetic plane change with aeroglide. For the reentry problem, several reduced order models were analyzed with the objective of optimal changes in heading with minimum energy loss. It was demonstrated that a further model order reduction to a single state model is possible through the application of singular perturbation theory. The optimal solution for the reduced problem defines an optimal altitude profile dependent on the current energy level of the vehicle. A separate boundary layer analysis is used to account for altitude and flight path angle dynamics, and to obtain lift and bank angle control solutions. By considering alternative approximations to solve the boundary layer problem, three guidance laws were derived, each having an analytic feedback form. The guidance laws were evaluated using a Maneuvering Reentry Research Vehicle model and all three laws were found to be near optimal. For the problem of synergetic plane change with aeroglide, a difficult terminal boundary layer control problem arises which to date is found to be analytically intractable. Thus a predictive/corrective solution was developed to satisfy the terminal constraints on altitude and flight path angle. A composite guidance solution was obtained by combining the optimal reentry solution with the predictive/corrective guidance method. Numerical comparisons with the corresponding optimal trajectory solutions show that the resulting performance is very close to optimal. An attempt was made to obtain numerically optimized trajectories for the case where heating rate is constrained. A first order state variable inequality constraint was imposed on the full order AOTV point mass equations of motion, using a simple aerodynamic heating rate model.

Calise, Anthony J.↗

NASA NTRS2016

Using FUN3D for Aeroelastic, Sonic Boom, and AeroPropulsoServoElastic (APSE) Analyses of a Supersonic Configuration

An overview of recent applications of the FUN3D CFD code to computational aeroelastic, sonic boom, and aeropropulsoservoelasticity (APSE) analyses of a low-boom supersonic configuration is presented. The overview includes details of the computational models developed including multiple unstructured CFD grids suitable for aeroelastic and sonic boom analyses. In addition, aeroelastic Reduced-Order Models (ROMs) are generated and used to rapidly compute the aeroelastic response and utter boundaries at multiple flight conditions.

Silva, Walter A.↗

NASA NTRS2004

Reduced-Order Blade Mistuning Analysis Techniques Developed for the Robust Design of Engine Rotors

The primary objective of this research program is to develop vibration analysis tools, design tools, and design strategies to significantly improve the safety and robustness of turbine engine rotors. Bladed disks in turbine engines always feature small, random blade-to-blade differences, or mistuning. Mistuning can lead to a dramatic increase in blade forced-response amplitudes and stresses. Ultimately, this results in high-cycle fatigue, which is a major safety and cost concern. In this research program, the necessary steps will be taken to transform a state-of-the-art vibration analysis tool, the Turbo-Reduce forced-response prediction code, into an effective design tool by enhancing and extending the underlying modeling and analysis methods. Furthermore, novel techniques will be developed to assess the safety of a given design. In particular, a procedure will be established for using eigenfrequency curve veerings to identify "danger zones" in the operating conditions--ranges of rotational speeds and engine orders in which there is a great risk that the rotor blades will suffer high stresses. This work also will aid statistical studies of the forced response by reducing the necessary number of simulations. Finally, new strategies for improving the design of rotors will be pursued. Several methods will be investigated, including the use of intentional mistuning patterns to mitigate the harmful effects of random mistuning, and the modification of disk stiffness to avoid reaching critical values of interblade coupling in the desired operating range. Recent research progress is summarized in the following paragraphs. First, significant progress was made in the development of the component mode mistuning (CMM) and static mode compensation (SMC) methods for reduced-order modeling of mistuned bladed disks (see the following figure). The CMM method has been formalized and extended to allow a general treatment of mistuning. In addition, CMM allows individual mode mistuning, which accounts for the realistic effects of local variations in blade properties that lead to different mistuning values for different mode types (e.g., mistuning of the first torsion mode versus the second flexural mode). The accuracy and efficiency of the CMM method and the corresponding Turbo-Reduce code were validated for an example finite element model of a bladed disk.

Min, James B.↗

NASA NTRS1989

Optimal aeroassisted coplanar orbital transfer using an energy model

The atmospheric portion of the trajectories for the aeroassisted coplanar orbit transfer was investigated. The equations of motion for the problem are expressed using reduced order model and total vehicle energy, kinetic plus potential, as the independent variable rather than time. The order reduction is achieved analytically without an approximation of the vehicle dynamics. In this model, the problem of coplanar orbit transfer is seen as one in which a given amount of energy must be transferred from the vehicle to the atmosphere during the trajectory without overheating the vehicle. An optimal control problem is posed where a linear combination of the integrated square of the heating rate and the vehicle drag is the cost function to be minimized. The necessary conditions for optimality are obtained. These result in a 4th order two-point-boundary-value problem. A parametric study of the optimal guidance trajectory in which the proportion of the heating rate term versus the drag varies is made. Simulations of the guidance trajectories are presented.

Halyo, Nesim↗

NASA NTRS1985

Frequency Domain Control Design of Large Space Structures: A Practical Approach

Requirements indicate the need for much larger, more accurate, and in some cases, very dynamic satellites. Large control system bandwidths are needed to meet accuracy and response requirements while maintaining tight control over appendage oscillations. Studies in recent years have shown that linear quadratic Gaussian (LQG) controllers can achieve the desired performance if the system is linearized and if the system model is accurate. Results of an LQG controller applied to a single axis satellite with large solar arrays, are given. A reduced order model (ROM) comprises rigid body motion with dominant structural modes. Optimal control and estimation gains are calculated based on an extremely conservative 0.0005 critical damping ratio. In order to examine stability characteristics, single-input single-output (SISO) frequency response concepts are generalized to develop a method of displaying open loop frequency response of multi-input multi-output (MIMO) control system.

Harding, R.↗

NASA NTRS1990

Active rejection of persistent disturbances in flexible space structures

A dynamic compensator for active rejection of persistent disturbances in flexible space structures is designed on the principle of the H(infinity)-optimization of the sensitivity transfer function matrix. A general state space solution is formulated to the multiinput multioutput H(infinity)-optimal control problem, allowing the use of the H(infinity)-optimal synthesis algorithm for the state-space models of space structures that result from model order reduction. Disturbances encountered in flexible space structures, such as shuttle docking, are investigated using the high-mode and the reduced-order models of a cantilevered two-bay truss, demonstrating the applicability of the H(infinity)-optimal approach.

Hwang, Cheng-Neng↗

NASA NTRS1990

Linear and non-linear dynamic models of a geared rotor-bearing system

A three degree of freedom non-linear model of a geared rotor-bearing system with gear backlash and radial clearances in rolling element bearings is proposed here. This reduced order model can be used to describe the transverse-torsional motion of the system. It is justified by comparing the eigen solutions yielded by corresponding linear model with the finite element method results. Nature of nonlinearities in bearings is examined and two approximate nonlinear stiffness functions are proposed. These approximate bearing models are verified by comparing their frequency responses with the results given by the exact form of nonlinearity. The proposed nonlinear dynamic model of the geared rotor-bearing system can be used to investigate the dynamic behavior and chaos.

Kahraman, Ahmet↗

NASA NTRS1998

MAP stability, design, and analysis

The Microwave Anisotropy Probe (MAP) is a follow-on to the Differential Microwave Radiometer (DMR) instrument on the Cosmic Background Explorer (COBE) spacecraft. The design and analysis of the MAP attitude control system (ACS) have been refined since work previously reported. The full spacecraft and instrument flexible model was developed in NASTRAN, and the resulting flexible modes were plotted and reduced with the Modal Significance Analysis Package (MSAP). The reduced-order model was used to perform the linear stability analysis for each control mode, the results of which are presented in this paper. Although MAP is going to a relatively disturbance-free Lissajous orbit around the Earth-Sun L(2) Lagrange point, a detailed disturbance-torque analysis is required because there are only a small number of opportunities for momentum unloading each year. Environmental torques, including solar pressure at L(2), aerodynamic and gravity gradient during phasing-loop orbits, were calculated and simulated. Thruster plume impingement torques that could affect the performance of the thruster modes were estimated and simulated, and a simple model of fuel slosh was derived to model its effect on the motion of the spacecraft. In addition, a thruster mode linear impulse controller was developed to meet the accuracy requirements of the phasing loop burns. A dynamic attitude error limiter was added to improve the performance of the ACS during large attitude slews. The result of this analysis is a stable ACS subsystem that meets all of the mission's requirements.

Ericsson-Jackson, A. J.↗

NASA NTRS1998

MAP Stability, Design and Analysis

The Microwave Anisotropy Probe (MAP) is a follow-on to the Differential Microwave Radiometer (DMR) instrument on the Cosmic Background Explorer (COBE) spacecraft. The design and analysis of the MAP attitude control system (ACS) have been refined since work previously reported. The full spacecraft and instrument flexible model was developed in NASTRAN, and the resulting flexible modes were plotted and reduced with the Modal Significance Analysis Package (MSAP). The reduced-order model was used to perform the linear stability analysis for each control mode, the results of which are presented in this paper. Although MAP is going to a relatively disturbance-free Lissajous orbit around the Earth-Sun L2 Lagrange point, a detailed disturbance-torque analysis is required because there are only a small number of opportunities for momentum unloading each year. Environmental torques, including solar pressure at L2, and aerodynamic and gravity gradient during phasing-loop orbits, were calculated and simulated. A simple model of fuel slosh was derived to model its effect on the motion of the spacecraft. In addition, a thruster mode linear impulse controller was developed to meet the accuracy requirements of the phasing loop burns. A dynamic attitude error limiter was added to improve the performance of the ACS during large attitude slews. The result of this analysis is a stable ACS subsystem that meets all of the mission's requirements.

Ericsson -Jackson, A.J.↗

NASA NTRS1998

Closed Loop Software Control of the MIDEX Power System

The Microwave Anisotropy Probe (MAP) is a follow-on to the Differential Microwave Radiometer (DMR) instrument on the Cosmic Background Explorer (COBE) spacecraft. The design and analysis of the MAP attitude control system (ACS) have been refined since work previously reported. The full spacecraft and instrument flexible model was developed in NASTRAN, and the resulting flexible modes were plotted and reduced with the Modal Significance Analysis Package (MSAP). The reduced-order model was used to perform the linear stability analysis for each control mode, the results of which are presented in this paper. Although MAP is going to a relatively disturbance-free Lissajous orbit around the Earth-Sun L2 Lagrange point, a detailed disturbance-torque analysis is required because there are only a small number of opportunities for momentum unloading each year. Environmental torques, including solar pressure at L2, and aerodynamic and gravity gradient during phasing-loop orbits, were calculated and simulated. A simple model of fuel slosh was derived to model its effect on the motion of the spacecraft. In addition, a thruster mode linear impulse controller was developed to meet the accuracy requirements of the phasing loop burns. A dynamic attitude error limiter was added to improve the performance of the ACS during large attitude slews. The result of this analysis is a stable ACS subsystem that meets all of the mission's requirements.

Castell, Karen↗

NASA NTRS2012

An Overview of the Semi-Span Super-Sonic Transport (S4T) Wind-Tunnel Model Program

A summary of computational and experimental aeroelastic (AE) and aeroservoelastic (ASE) results for the Semi-Span Super-Sonic Transport (S4T) wind-tunnel model is presented. A broad range of analyses and multiple AE and ASE wind-tunnel tests of the S4T wind-tunnel model have been performed in support of the ASE element in the Supersonics Program, part of the NASA Fundamental Aeronautics Program. This paper is intended to be an overview of multiple papers that comprise a special S4T technical session. Along those lines, a brief description of the design and hardware of the S4T wind-tunnel model will be presented. Computational results presented include linear and nonlinear aeroelastic analyses, and rapid aeroelastic analyses using CFD-based reduced-order models (ROMs). A brief survey of some of the experimental results from two open-loop and two closed-loop wind-tunnel tests performed at the NASA Langley Transonic Dynamics Tunnel (TDT) will be presented as well.

Silva, Walter A.↗

NASA NTRS2015

Computational Aeroelastic Analyses of a Low-Boom Supersonic Configuration

An overview of NASA's Commercial Supersonic Technology (CST) Aeroservoelasticity (ASE) element is provided with a focus on recent computational aeroelastic analyses of a low-boom supersonic configuration developed by Lockheed-Martin and referred to as the N+2 configuration. The overview includes details of the computational models developed to date including a linear finite element model (FEM), linear unsteady aerodynamic models, unstructured CFD grids, and CFD-based aeroelastic analyses. In addition, a summary of the work involving the development of aeroelastic reduced-order models (ROMs) and the development of an aero-propulso-servo-elastic (APSE) model is provided.

Silva, Walter A.↗

NASA NTRSDate not supplied

Closed-Loop Simulations of Human-Scale Mars Lander Descent Trajectories on Frontier

A computational campaign was performed to run high-fidelity, free-flight simulations of a human-scale Mars lander concept vehicle decelerating under retropropulsion through the Martian atmosphere with closed-loop flight control. A novel approach is used to couple computational fluid dynamics (CFD) software with a mature flight mechanics package, where the two applications communicate in real-time across two geographically-dispersed computational facilities. The CFD is performed on the Frontier exascale system located at Oak Ridge National Laboratory, and the flight mechanics are executed on a system located at NASA Langley Research Center. In the current campaign, CFD is performed using finite-rate chemistry to account for the interactions between the LOXCH 4 engines and the CO 2 Martian atmosphere. A simulation of a closed-loop main engine throttling and RCS actuation is presented, demonstrating that the vehicle and model are able to maintain stability in a long-duration CFD-in-the-loop flight simulation. Comparisons are made to a reduced order model ignoring aero-propulsive interactions.

CFD↗

NASA NTRS2017

LPV Modeling of a Flexible Wing Aircraft Using Modal Alignment and Adaptive Gridding Methods

One of the earliest approaches in gain-scheduling control is the gridding based approach, in which a set of local linear time-invariant models are obtained at various gridded points corresponding to the varying parameters within the flight envelop. In order to ensure smooth and effective Linear Parameter-Varying control, aligning all the flexible modes within each local model and maintaining small number of representative local models over the gridded parameter space are crucial. In addition, since the flexible structural models tend to have large dimensions, a tractable model reduction process is necessary. In this paper, the notion of s-shifted H2- and H Infinity-norm are introduced and used as a metric to measure the model mismatch. A new modal alignment algorithm is developed which utilizes the defined metric for aligning all the local models over the entire gridded parameter space. Furthermore, an Adaptive Grid Step Size Determination algorithm is developed to minimize the number of local models required to represent the gridded parameter space. For model reduction, we propose to utilize the concept of Composite Modal Cost Analysis, through which the collective contribution of each flexible mode is computed and ranked. Therefore, a reduced-order model is constructed by retaining only those modes with significant contribution. The NASA Generic Transport Model operating at various flight speeds is studied for verification purpose, and the analysis and simulation results demonstrate the effectiveness of the proposed modeling approach.

LPV Modeling↗

NASA NTRSDate not supplied

Aeroservoelastic Control Law Development for the Integrated Adaptive Wing Technology Maturation Wind-Tunnel Test

In this paper, a linear quadratic Gaussian (LQG) regulator was applied to a computational aeroservoelastic (ASE) model of the Integrated Adaptive Wing Technology Maturation (IAWTM) wind-tunnel model to demonstrate its effectiveness for active flutter suppression. The aerodynamics within this computational ASE model were solved using unsteady Reynolds-averaged Navier-Stokes (RANS) equations; the structural dynamics of the model were solved using modal analysis. This RANS-based ASE model was used as the plant for the LQG regulator. The Kalman filter and controller used within the LQG regulator were derived from a reduced-order model (ROM) of the RANS-based ASE model. This ROM-based ASE model was generated using system identification techniques. It was shown that the Kalman filter adequately predicted important states of the plant, and that LQG regulator successfully stabilized an aeroelastically unstable plant without exceeding reasonable control surface limitations. All of this was demonstrated using simulation data, and the methods presented here appear feasible for use in the upcoming IAWTM wind-tunnel tests.

Josiah M. Waite↗

NASA NTRS1987

Model reductions using a projection formulation

A new methodology for model reduction of MIMO systems exploits the notion of an oblique projection. A reduced model is uniquely defined by a projector whose range space and orthogonal to the null space are chosen among the ranges of generalized controllability and observability matrices. The reduced order models match various combinations (chosen by the designer) of four types of parameters of the full order system associated with (1) low frequency response, (2) high frequency response, (3) low frequency power spectral density, and (4) high frequency power spectral density. Thus, the proposed method is a computationally simple substitute for many existing methods, has an extreme flexibility to embrace combinations of existing methods and offers some new features.

De Villemagne, Christian↗

NASA NTRS1981

Model error estimation for large flexible spacecraft

The basic model obtained for spacecraft control system design applications is used to develop the control and estimation algorithms which constitute integral elements of the control system. The performance of this system is limited on account of modeling errors. The presence of such errors is inevitable in connection with truncated dynamics, parameter uncertainties, neglected nonlinearities, and external disturbances. In many cases, an approximate knowledge of the model errors can only be established by means of an estimation procedure. The present investigation has the objective to outline an approach to estimate errors inherent in a reduced-order model and to illustrate its application to modeling problems arising in spacecraft control system design. The considered procedure makes use of the principle of least-squares. In the discussed application this principle is employed to minimize a quadratic functional of the model errors.

Rodriguez, G.↗

NASA NTRS1980

Finite element models and feedback control of flexible aerospace structures

Large flexible aerospace structures, such as the solar power satellite, are distributed parameter systems with very complex continuum descriptions. This paper investigates the use of finite element methods to produce reduced-order models and finite dimensional feedback controllers for these structures. The main results give conditions under which stable control of the finite element model will produce stable control of the actual structure.

Balas, M. J.↗