Search NASA⌕ Search

SEARCH · Search NASA

Results for “Relative Permeability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Uniaxial Creep as a Control on Mercury Intrusion Capillary Pressure in Consolidating Rock Salt

The nature of geologic disposal of nuclear waste in salt formations requires validated and verified two-phase flow models of transport of brine and gas through intact, damaged, and consolidating crushed salt. Such models exist in other realms of subsurface engineering for other lithologic classes (oil and gas, carbon sequestration etc. for clastics and carbonates) but have never been experimentally validated and parameterized for salt repository scenarios or performance assessment. Models for waste release scenarios in salt back-fill require phenomenological expressions for capillary pressure and relative permeability that are expected to change with degree of consolidation, and require experimental measurement to parameterize and validate. This report describes a preliminary assessment of the influence of consolidation (i.e. volume strain or porosity) on capillary entry pressure in two phase systems using mercury injection capillary pressure (MICP). This is to both determine the potential usefulness of the mercury intrusion porosimetry method, but also to enable a better experimental design for these tests. Salt consolidation experiments are performed using novel titanium oedometers, or uniaxial compression cells often used in soil mechanics, using sieved run-of-mine salt from the Waste Isolation Pilot Plant (WIPP) as starting material. Twelve tests are performed with various starting amounts of brine pore saturation, with axial stresses up to 6.2 MPa (~900 psi) and temperatures to 90°C. This corresponds to UFD Work Package 15SN08180211 milestone “FY:15 Transport Properties of Run-of-Mine Salt Backfill – Unconsolidated to Consolidated”. Samples exposed to uniaxial compression undergo time-dependent consolidation, or creep, to various degrees. Creep volume strain-time relations obey simple log-time behavior through the range of porosities (~50 to 2% as measured); creep strain rate increases with temperature and applied stress as expected. Mercury porosimetry is used to determine characteristic capillary pressure curves from a series of consolidation tests and show characteristic saturation-capillary pressure curves that follow the common van Genuchten (1978, 1980) formulation at low stresses. Higher capillary pressure data are suspect due to the large potential for sample damage, including fluid inclusion decrepitation and pore collapse. Data are supportive of use of the Leverett “J” function (Leverett, 1941) to use for scaling characteristic curves at different degrees of consolidation, but better permeability determinations are needed to support this hypothesis. Recommendations for further and refined testing are made with the goal of developing a self- consistent set of constitutive laws for granular salt consolidation and multiphase (brine-air) flow.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Phase 2: Updated Geothermal Play Fairway Analysis of the Tularosa Basin, New Mexico

Play fairway analysis (PFA) methodologies, both deterministic and stochastic, are being applied for medium to low enthalpy geothermal resources in the Tularosa Basin, in south-central New Mexico. These PFA methods use datasets representative of heat, groundwater and fault-fracture related permeability to locate areas with the lowest risk of geothermal energy development. Our Phase 1 PFAs predicted several plays throughout the study area, with a range of certainty and risk, based upon legacy data. In Phase 2, new data were collected for high priority plays and integrated into the PFAs to enhance certainty and further reduce risk. Field geology, gravity surveys and alluvial fan geomorphology supplemented the understanding of geologic structure and potential permeability, while additional well sampling, geothermometry and temperature logging provided valuable information about heat in the subsurface. In order to statistically compare and contrast the layers of evidence in the Tularosa Basin with the broader Great Basin, a probabilistic Weights of Evidence analysis was conducted in parallel with the inclusive and deterministic petroleum industry logic PFA. Both methods yielded 3 similar plays, while Weights of Evidence identified 2 additional plays. A sixth play was inferred around the NASA-Aerospace Data Facility Southwest site, north-east of Las Cruces, based on a promising shallow temperature survey, geothermometers, and structural interpretations of geophysical data. Here, the White Sands Missile Range main cantonment (headquarters) play is now given high priority, along with McGregor Range, Fort Bliss, due to the discovery of relatively high geothermometer values.

15 GEOTHERMAL ENERGY↗

Preliminary Stress-Annealing Process and its Effect on Magnetic Properties of Fe-based Soft Magnetic Alloys

Stress-annealing (SA) is a novel secondary processing technique capable of significantly increasing magnetic anisotropy and controlling magnetic permeability in planar-cast amorphous precursor ribbons. In this technical memorandum, measures taken to improve the mechanical handling of brittle Fe-based ribbons are described for a custom SA system. This system was then used to process a series of Fe-based alloys (Fe-2Nb-2Mo-1Cu-15.5Si-7B at.%, Fe-5Co-3Ta-1Cu-16Si-6.5B at.%, and Fe-5Co-3Ta-1Cu-16.5Si-6B at.%) and the resulting magnetic properties were determined. The Fe-5Co-3Ta-1Cu-16.5Si-6B at.% alloy was found to be the most promising composition of the three in terms of surviving an optimized spool-to-spool continuous SA process under 90 MPa of tensile stress at 650 °C using a feed rate of 75.5 in/min, which equated to approximately 10 second anneal time. These optimally annealed ribbons exhibited flat hysteresis loops with a saturation magnetization of nearly 1.2 T, low magnetic coercivity (≈ 2 A m-1), and relative permeability of approximately 500.

soft magnetic alloy↗

Potosi Reservoir Modeling; History and Recommendations

As a part of a larger project co-funded by the United States Department of Energy (US DOE) to evaluate the potential of formations within the Cambro-Ordovician strata above the Mt. Simon as potential targets for carbon sequestration in the Illinois and Michigan Basins, the Illinois Clean Coal Institute (ICCI) requested Schlumberger to evaluate the potential injectivity and carbon dioxide (CO₂) plume size of the Cambrian Potosi Formation. The evaluation of this formation was accomplished using wireline data, core data, pressure data, and seismic data from two projects: the US DOE-funded Illinois Basin–Decatur Project being conducted by the Midwest Geological Sequestration Consortium in Macon County, Illinois, as well as data from the Illinois – Industrial Carbon Capture and Sequestration (IL-ICCS) project funded through the American Recovery and Reinvestment Act. In 2010, technical performance evaluations on the Cambrian Potosi Formation were performed through reservoir modeling. The data included formation tops from mud logs, well logs from the Verification Well 1 (VW1) and the Injection Well (CCS1), structural and stratigraphic formation from three dimensional (3D) seismic data, and field data from several waste water injection wells for the Potosi Formation. The intention was for two million tonnes per annum (MTPA) of CO₂ to be injected for 20 years into the Potosi Formation. In 2013, updated reservoir models for the Cambrian Potosi Formation were evaluated. The data included formation tops from mud logs, well logs from the CCS1, VW1, and Verification Well 2 (VW2) wells, structural and stratigraphic formation from a larger 3D seismic survey, and field data from several waste water injection wells for Potosi Formation. The objective is to simulate the injection of CO₂ at a rate 3.5 million tons per annum (3.2 million tonnes per annum [MTPA]) for 30 years 106 million tons (96 MT total) into the Potosi Formation. The Potosi geomodeling efforts have evolved from using data from a single well in 2010 to the inclusion of data from three wells in 2013 which largely leverage the porosity and permeability logs plus knowledge of lost circulation zones. The first Potosi model (Potosi Geobody Model 2010) attempted to use the available seismic inversion data to inform the geomodel and predict vugular zones in advance of drilling VW1. Lost circulation zones in VW1 came in as the geologists predicted. The model was not implemented in subsequent simulation work. To date, reservoir models used for flow simulation work have relied predominately on Gaussian distributed properties (porosity and permeability) and have employed a single injection well. Potosi Model 2013b incorporated the new VW2 logs, and exhibited an extra level of sophistication by delineating the vugular intervals. This method added further realism that likely represents the best reservoir approximation to date. Where the 2010 reservoir models were 10 by 10 mi (16 by 16 km) in area, the 2013 models were expanded in size to 30 by 30 mi (48 by 48 km). The latest reservoir simulations show that a minimum of four injectors might be required to meet target injection rates. Still, there is data that requires further scrutiny and modeling methodologies that require testing for the Potosi Formation. This work is currently ongoing, and the next phase of the reservoir modeling intends to implement valuable data like porosity derived from seismic inversion, seismically derived geobodies, or a combination of both to further define vugular zones and the porosity distribution within the Potosi Formation. Understanding the dual porosity, dual permeability character of the Potosi remains the greatest challenge in representing this formation. Further analysis of the FMI* fullbore formation microimager data may aid in assessing this uncertainty. The Potosi Formation is indeed an interesting formation, and recommendations to further characterize it are included in the following list: - Data acquisition to identify the vugs permeability, distribution, and interconnectivity could be considered to perform a more rigorous evaluation of the Potosi Formation injectivity and capacity. This could be achieved by performing an injection test on a vugular interval to determine the vugs permeability, and an interference test between wells to evaluate the local vugs extent and interconnectivity. - A thorough study of the available FMI data may reveal specifics on estimating the vug to matrix ratio. This estimate could be used to further condition the porosity distribution. Porosity logs alone might underestimate the formation’s porosity associated with vugs. Porosity mapping derived from the seismic inversion could also be used in the succeeding task to characterize the lateral porosity distribution within the reservoir. This could involve the geobody methodology previously attempted in 2010. With or without seismic inversion porosity mapping, it is worth exploring whether increased lateral heterogeneity plays a significant role in Potosi injectivity. Investigations on vugular, dolomitic outcrops suggest that there may be significantly greater lateral heterogeneity than what has been modeled here. - The FMI data also reveals the presence of and helps describe open fractures. The presence of fractures will further enhance the formation’s permeability. The task of leveraging this data in the geomodeling effort still remains. Under the best of circumstances, this data describing open fractures may be combined with seismic attributes to delineate fracture corridors. Fracture modeling would certainly add another layer of sophistication to the model. Its contribution and applicability remain to be explored. - Facies modeling within the Potosi has yet to be thoroughly addressed. The carbonates during the time of deposition are believed to be regionally extensive. However, it may be worth delineating the reservoir with other regional wells or modern day analogues to understand the extent of the Potosi. More specifically, the model could incorporate lateral changes or trends if deemed necessary to represent facies transition. - Currently there is no fracture gradient data available for the Potosi in the Decatur project area. The acquisition of the fracture pressure data could be considered to determine an appropriate maximum allowable bottomhole injection pressure. This would allow the evaluation of injectivity and the required number of wells in a more precise manner. - Special core analysis (SCAL) to determine the relative permeability and capillary pressure of the vugs and matrix could be considered to have a better estimation of the reservoir injectivity and plume extent. - Formation water sampling and analysis could be considered for the Potosi to estimate the water salinity and properties. A vertical flow performance evaluation could be considered for the succeeding task to determine the appropriate tubing size, the required injection tubing head pressure, and to investigate whether the corresponding well injection rate falls within the tubing erosional velocity limit. - A simulation using several injectors could also be considered to determine the required number of wells to achieve the injection target while taking into account the pressure interference.

Smith, Valerie↗

Geology and in situ stress of the MH-2 borehole, Idaho, USA: Insights into western Snake River Plain structure from geothermal exploration drilling

Project HOTSPOT, the Snake River Scientific Drilling Project (International Continental Scientific Drilling Program), tested for deep geothermal resources and examined the petrology of volcanic rocks with three drillholes in the central and western Snake River Plain (western USA). The MH-2 drillhole targeted fractured crystalline and hydrothermally altered basalt in the area of the Mountain Home Air Force Base (Idaho) to a total depth of 1821 m. At 1745 m depth the drillhole encountered flowing artesian hydrothermal fluids of at least 150 °C. We integrate geological analyses of core, image log, and borehole geophysical data, and in situ stress analyses to describe the structural environment that produces permeability for artesian flow. The rocks in the lower 540 m of the drillhole consist of basalt flows as much as 30 m thick, altered basalt, and thin sedimentary horizons. The mechanical stratigraphy is defined by nine mechanical horizons that are in three ranges of rock strength on the basis of experimentally determined strength data, core logging, and geophysical log signatures. Hydrothermal alteration products and mineralization in the core are associated with three highly faulted sections; the lowermost section is associated with the zone of flowing thermal water. Shear slip indicators on faults observed in core indicate slip ranging from pure strike slip to normal failure mechanisms in the stronger horizons. The borehole breakouts indicate that the maximum horizontal stress, SH, is oriented 047° ± 7°, and drilling-induced tensile fractures indicate that SH is oriented at 67° ± 21°. The in situ stress orientations exhibit little variation over the depth of the measured interval, but the SH magnitude varies with depth, and is best explained by an oblique normal fault stress regime. The geomechanical model indicates that if pore pressures at depth are elevated above the normal hydrostatic gradient, as observed here, the system has the potential to deform by mixed normal and strike-slip failure. Our observations and interpretations suggest that the MH-2 borehole was drilled into oblique normal faults that intersect a buried 300°-trending fault block masked by the basaltic volcanic complex. These data indicate that the transition from the central to western Snake River Plain is characterized by complex structures developed in response to a transitional stress state related to Snake River Plain and western Basin and Range stress regimes. Furthermore, the western Basin and Range stress and tectonic regime may extend from northern Nevada into western Idaho and may enhance the potential for geothermal resources by creating interconnected fracture and fault-related permeability at depth.

15 GEOTHERMAL ENERGY↗

Thermal and capillary effects on the caprock mechanical stability at In Salah, Algeria

Thermo-mechanical effects are important in geologic carbon storage because CO 2 will generally reach the storage formation colder than the rock, inducing thermal stresses. Capillary functions, i.e., retention and relative permeability curves, control the CO 2 plume shape, which may affect overpressure and thus, caprock stability. To analyze these thermal and capillary effects, we numerically solve non-isothermal injection of CO 2 in deformable porous media considering the In Salah, Algeria, CO 2 storage site. Here, we find that changes in the capillary functions have a negligible effect on overpressure and thus, caprock stability is not affected by capillary effects. But, we show that for the strike slip stress regime prevalent at In Salah, stability decreases in the lowest parts of the caprock during injection due to cooling-induced thermal stresses. Simulations show that shear slip along pre-existing fractures may take place in the cooled region, whereas tensile failure is less likely to occur. Indeed, only the injection zone and the lowest tens of meters of the 900-m-thick caprock at In Salah might be affected by cooling effects, which would thus not jeopardize the overall sealing capacity of the caprock. Furthermore, faults are likely to remain stable far away from the injection well because outside the cooled region the injection-induced stress changes are not sufficient to exceed the anticipated shear strength of minor faults. Nonetheless, we recommend that thermal effects should be considered in the site characterization and injection design of future CO 2 injection sites to assess caprock stability and guarantee a permanent CO 2 storage.

54 ENVIRONMENTAL SCIENCES↗

Simulation of Multiphase Flow and Poromechanical Effects Around Injection Wells in CO 2 Storage Sites

In geological CO 2 storage operations, wellbore deformations and leakage pathways formations can occur around injection and abandoned wells subjected to high rates and long-term CO 2 injection. To guide engineering design and prevent CO 2 leakage risks, a full understanding of the underlying physics and robust numerical models is necessary to evaluate the response of underground formations in the near wellbore region and in the reservoir. In this study, a multi-scale and multi-physics open-source simulator (GEOS) is used to simulate multiphase flow and poromechanical deformations over time in three dimensions. The governing equations for mechanical deformations of the rock body and multiphase compositional fluid flow within the rock matrix are solved with a fully coupled finite element and finite volume approach. The Drucker–Prager model with friction hardening is applied to simulate elastoplastic deformation and a multiphase fluid model with power-law correlations for relative permeability is used to model the migration of CO 2 plume, which are coupled with numerical implicit scheme. Simulation results are verified against multiple analytical solutions for multiphase flow and wellbore problems, thus demonstrating the accuracy of this advanced simulator. In two engineering applications, here we highlight the impact of elastoplastic deformation and coupled modeling for assessing induced displacements and stress perturbations, which are more pronounced in the near wellbore regions. This work focuses on short-term processes in the vicinity of injection wells where stress evolutions, rock deformations and multiphase compositional flow and transport are simulated jointly to ensure wellbore stability and prevent damage. This fully coupled geomechanical model can simulate multiphase flow and any associated poromechanical effects within the CO 2 storage site and in the surrounding formations. Such a large-scale, long-term, multi-physics simulation model is useful in many ways: it can guide operational decisions for CO 2 injection, assess the containment potential and risks of a site, and analyze the wellbore stability and integrity during and after CO 2 injection.

58 GEOSCIENCES↗

Two-Phase Flow Mechanisms Controlling CO2 Intrusion into Shaly Caprock

Abstract Geologic carbon storage in deep saline aquifers has emerged as a promising technique to mitigate climate change. CO 2 is buoyant at the storage conditions and tends to float over the resident brine jeopardizing long-term containment goals. Therefore, the caprock sealing capacity is of great importance and requires detailed assessment. We perform supercritical CO 2 injection experiments on shaly caprock samples (intact caprock and fault zone) under representative subsurface conditions. We numerically simulate the experiments, satisfactorily reproducing the observed evolution trends. Simulation results highlight the dynamics of CO 2 flow through the specimens with implications to CO 2 leakage risk assessment in field practices. The large injection-induced overpressure drives CO 2 in free phase into the caprock specimens. However, the relative permeability increase following the drainage path is insufficient to provoke an effective advancement of the free-phase CO 2 . As a result, the bulk CO 2 front becomes almost immobile. This implies that the caprock sealing capacity is unlikely to be compromised by a rapid capillary breakthrough and the injected CO 2 does not penetrate deep into the caprock. In the long term, the intrinsically slow molecular diffusion appears to dominate the migration of CO 2 dissolved into brine. Nonetheless, the inherently tortuous nature of shaly caprock further holds back the diffusive flow, favoring safe underground storage of CO 2 over geological time scales.

58 GEOSCIENCES↗

A second-order accurate finite volume scheme with the discrete maximum principle for solving Richards’ equation on unstructured meshes

Richards’s equation describes steady-state or transient flow in a variably saturated medium. For a medium having multiple layers of soils that are not aligned with coordinate axes, a mesh fitted to these layers is no longer orthogonal and the classical two-point flux approximation finite volume scheme is no longer accurate. Here, we propose new second-order accurate nonlinear finite volume (NFV) schemes for the head and pressure formulations of Richards’ equation. We prove that the discrete maximum principles hold for both formulations at steady-state which mimics similar properties of the continuum solution. The second-order accuracy is achieved using high-order upwind algorithms for the relative permeability. Numerical simulations of water infiltration into a dry soil show significant advantage of the second-order NFV schemes over the first-order NFV schemes even on coarse meshes. Since explicit calculation of the Jacobian matrix becomes prohibitively expensive for high-order schemes due to build-in reconstruction and slope limiting algorithms, we study numerically the preconditioning strategy introduced recently in Lipnikov et al. (2016) that uses a stable approximation of the continuum Jacobian. Lastly, numerical simulations show that the new preconditioner reduces computational cost up to 2–3 times in comparison with the conventional preconditioners.

97 MATHEMATICS AND COMPUTING↗

Comprehensive parametric study of CO 2 sequestration in deep saline aquifers

Carbon dioxide injection in deep saline aquifers is a key method for permanently sequestering anthropogenic CO 2 . Here this study employs a reactive transport model to explore mineral precipitation/dissolution and its impact on reservoir properties in deep saline aquifers. We also assess capillary pressure and relative permeability hysteresis on various CO 2 trapping mechanisms. Results from this study reveal the significant influence of initial brine composition on mineral precipitation/dissolution. The dissolution and precipitation of minerals have different effects around the wellbores compared to the overall reservoir. Additionally, salt concentration (Ca ++ and Mg ++ ) and quartz surface area affect CO 2 mineralization, while Na + impacts halite precipitation, altering flow properties. The effect of capillary pressure is significant, as including the capillary pressure in the simulation case resulted in significantly improved CO 2 trapping, achieving almost total dissolution of the injected CO 2 in around 300 years. This study offers novel insights into the interactions of reservoir minerals, brine properties, and the injected CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The impact of capillary heterogeneity on CO 2 flow and trapping across scales

Capillary heterogeneity has been identified over the last decade as a key control on subsurface CO 2 flow behavior during geological CO 2 sequestration. These heterogeneities can be formed in all sedimentary rocks, ranging from slight variations in the sand grain sizes to extensive sequences of interbedded sands, shales, and limestones. Capillary heterogeneity has been largely, although not entirely, overlooked in subsurface flow modeling because it is assumed to only directly influence fluid redistribution over scales of centimeters to meters. However, even small-scale fluid movements can result in dramatic impacts on the mobility and trapping of the CO 2 over kilometers. Therefore, neglecting capillary heterogeneity at multiple scales could potentially lead to errors in modeling and predicting field-scale plume migration. In this review paper, we aim to provide a consistent overview to (1) establish that capillary heterogeneity can have a major impact on CO 2 plume migration, (2) establish the respective length scales at which capillary heterogeneity matters, and (3) provide guidance for numerical modeling. This review covers pertinent literature and extracts key observations from the core to the field scales. Experimental studies have shown that millimeter-decimeter scale capillary heterogeneity can cause the so-called capillary heterogeneity trapping in addition to pore-scale residual trapping. Even at such a small scale, capillary heterogeneity can already lead to complex upscaled constitutive relationships, such as flow-rate dependent and anisotropic relative permeability, which affects field-scale CO 2 migration even when field-scale heterogeneities are present. Under gravity-dominated flow regimes, centimeter-meter scale capillary heterogeneity can entrap a significant amount of CO 2 at field scale, not just after imbibition but also during drainage. In certain cases, the presence of capillary heterogeneity can even completely stop the vertical movement of the CO 2 plume, hence greatly reducing leakage risks. At meter-kilometer scale, the influence of capillary heterogeneity is more pronounced and can hinder or redirect CO 2 migration in both lateral and vertical directions. The impact of capillary heterogeneity across multiple spatial scales poses a great challenge in modeling CO 2 migration at field scale, because it is practically impossible to build a field-scale earth model with grid blocks at millimeter scale. We recommend a hierarchical modeling approach to address this challenge. At field scale, earth models are built to capture geological features and heterogeneities in high but still practical grid resolutions. For each facies or rock type of the field-scale model, high- resolution meter-scale “conceptual” models are built with millimeter-scale grid blocks to capture representative fine-scale bedding geometries and heterogeneities in various environments of deposition, bridging the gap from subcore scale to the size of a field-scale simulation grid block. Upscaling is then used to preserve the smaller-scale flow dynamics of various rock types in field-scale simulations. Here, future work is needed to (1) refine, improve, and validate the hierarchical modeling approach; (2) build libraries of fine-scale bedding models for facies in various environments of deposition; (3) quantify multiscale capillary heterogeneity effects under subsurface uncertainties; (4) gain learning from different storage formations; and (5) establish best practices that balance accuracy and computational speed.

Capillary heterogeneity↗

A connectivity-based modeling approach for representing hysteresis in macroscopic two-phase flow properties

During CO 2 injection and storage in deep reservoirs, the injected CO 2 enters into an initially brine saturated porous medium, and after the injection stops, natural groundwater flow eventually displaces the injected mobile-phase CO 2 , leaving behind residual non-wetting fluid. Accurate modeling of two-phase flow processes are needed for predicting fate and transport of injected CO 2 , evaluating environmental risks and designing more effective storage schemes. The entrapped non-wetting fluid saturation is typically a function of the spatially varying maximum saturation at the end of injection. At the pore-scale, distribution of void sizes and connectivity of void space play a major role for the macroscopic hysteresis behavior and capillary entrapment of wetting and non-wetting fluids. This paper presents development of an approach based on the connectivity of void space for modeling hysteretic capillary pressure-saturation-relative permeability relationships. The new approach uses void-size distribution and a measure of void space connectivity to compute the hysteretic constitutive functions and to predict entrapped fluid phase saturations. Two functions, the drainage connectivity function and the wetting connectivity function, are introduced to characterize connectivity of fluids in void space during drainage and wetting processes. These functions can be estimated through pore-scale simulations in computer-generated porous media or from traditional experimental measurements of primary drainage and main wetting curves. The hysteresis model for saturation-capillary pressure is tested successfully by comparing the model-predicted residual saturation and scanning curves with actual data sets obtained from column experiments found in the literature. A numerical two-phase model simulator with the new hysteresis functions is tested against laboratory experiments conducted in a quasi-two-dimensional flow cell (91.4cm×5.6cm×61cm), packed with homogeneous and heterogeneous sands. Initial results show that the model can predict spatial and temporal distribution of injected fluid during the experiments reasonably well. However, further analyses are needed for comprehensively testing the ability of the model to predict transient two-phase flow processes and capillary entrapment in geological reservoirs during geological carbon sequestration.

58 GEOSCIENCES↗

Integrated geological, economic, and risk assessment of underground hydrogen storage

Underground hydrogen storage (UHS) is a promising option to buffer variable renewable power and support the hydrogen economy. Yet this technology is early-stage, and key uncertainties remain about how coupled processes such as geochemical and geomechanical impacts affect long-term storage security. In this paper, we seek to integrate the results from a large, multi-scale research program to quantify core feasibility metrics and situate these studies within ongoing efforts. Through this work, we evaluate hydrogen recoverability during storage by assessing diffusive losses, losses to geochemical interactions and their subsequent impact on geomechanical properties, and losses to residual saturation during injection and withdrawal. Molecular and laboratory studies show that lithologic heterogeneity, pore geometry, and mineral surface chemistry govern hydrogen–rock interactions, controlling loss pathways. High-pressure coreflooding is used to estimate relative permeabilities and measure parameters needed for reservoir-scale sensitivity analyses. These core-scale experiments found early hydrogen breakthrough at low saturations driven by capillary and viscous fingering, which limits pore-space utilization at early times, while repeated injection and withdrawal cycles improve deliverability over time. Technoeconomic factors and purity requirements for end uses are also considered as part of our comprehensive feasibility analysis. Finally, we underscore the importance of geophysical monitoring and tailored injection strategies to maintain integrity and efficiency. Together, these results provide a quantitative foundation for safe, scalable deployment of UHS and highlight priorities for future integrated studies.

08 HYDROGEN↗

Informing field-scale CO 2 storage simulations with sandbox experiments: The effect of small-scale heterogeneities

Small-scale heterogeneities can significantly affect the fate of the CO 2 plume and trapping during CO 2 migration. We conducted geologic carbon storage field-scale simulations to investigate the impact of small-scale heterogeneities on plume dynamics and trapping performance. Small-scale heterogeneities have been shown to increase the amount of trapped CO 2 during buoyancy-driven flow. The trapped CO 2 saturation is validated by previous sandbox experimental work during buoyancy-driven flow in realistic heterogeneous domains and is implemented through the critical CO 2 saturation parameter (i.e., the first non-zero value in the drainage CO 2 relative permeability curve). Depending on the type and degree of heterogeneity, various critical CO 2 saturation values are exhibited. Furthermore, we investigated the effect of small-scale heterogeneities when multiple capillary pressure models are employed. This study demonstrates that an increase in critical CO 2 saturation reduces the CO 2 plume size and lateral extent, accompanying an increase in residual trapping and a decrease in solubility trapping. Lastly, we show that independent of the capillary pressure model used, an increase in critical saturation leads to similar CO 2 plume dynamics distribution and trapping performance. These results emphasize the importance of quantifying the effect of small-scale heterogeneity as they affect the large-scale behavior of the CO 2 plume.

58 GEOSCIENCES↗

Model Fit to Experimental Data for Foam-Assisted Deep Vadose Zone Remediation

Foam has been regarded as a promising means of remeidal amendment delivery to overcome subsurface heterogeneity in subsurface remediation processes. This study investigates how a foam model, developed by Method of Characteristics and fractional flow analysis in the companion paper of Roostapour and Kam (2012), can be applied to make a fit to a set of existing laboratory flow experiments (Zhong et al., 2009) in an application relevant to deep vadose zone remediation. This study reveals a few important insights regarding foam-assisted deep vadose zone remediation: (i) the mathematical framework established for foam modeling can fit typical flow experiments matching wave velocities, saturation history , and pressure responses; (ii) the set of input parameters may not be unique for the fit, and therefore conducting experiments to measure basic model parameters related to relative permeability, initial and residual saturations, surfactant adsorption and so on should not be overlooked; and (iii) gas compressibility plays an important role for data analysis, thus should be handled carefully in laboratory flow experiments. Foam kinetics, causing foam texture to reach its steady-state value slowly, may impose additional complications.

Roostapour, A.↗

Injection data analysis using material balance time for CO 2 storage capacity estimation in deep closed saline aquifers

Estimating the ultimate storage capacity of deep saline aquifers is important to address the formation potential to store the envisioned large volumes of CO 2 . Injection data (i.e. injection rate, bottomhole pressure, and cumulative injected volume of CO 2 ) are routinely recorded during storage operations. These data contain valuable information on the subsurface (e.g. the reservoir pore volume and the formation storage capacity) that can be extracted. In this paper, we present a two-step graphical technique to infer the pore volume and the ultimate storage capacity of closed saline aquifers by analyzing the available injection data. First, the pore volume is inferred through adapting the concept of the material balance time. Material balance time is an approximate superposition time function developed to interpret production data from oil and gas wells operating at variable pressure/rate conditions during the boundary-dominated flow period. Using material balance techniques, the ultimate storage capacity is then estimated through linear extrapolation of the average pressure trend to the maximum allowable pressure the formation can withstand. The average pressure is not available in practice, but is can be obtained from the injection data. Two approaches are presented in this study to calculate the average pressure; namely the rigorous and the approximate approaches. Unlike the rigorous approach, the approximate approach does not require a prior knowledge of some reservoir properties (e.g. relative permeability, absolute permeability, formation porosity and thickness) to calculate the average pressure. To investigate its potential and reliability in analyzing CO 2 injection data, the proposed technique is applied to four synthetic cases representing different well operating conditions. Results indicate that the approximate approach consistently overestimates the actual (simulated) storage capacity as compared to the rigorous approach. The agreement - between the inferred and the simulated reservoir pore volume, and between the analytical and numerical estimates of storage capacity - validates the potential application of the technique to CO 2 storage in closed saline aquifers. The technique is further substantiated through application to a field data set utilized from a commercial-scale geological storage (CGS) project. Finally, field data interpretation shows that the proposed technique can be utilized to identify the degree of hydraulic continuity and reservoir compartmentalization within a target formation by interpreting the corresponding pressure and rate responses.

02 PETROLEUM↗

Numerical Analysis of Experiments on Thermally Induced Dissociation of Methane Hydrates in Porous Media

Numerical simulation is essential for the prediction and evaluation of hydrocarbon reservoir performance. Numerical simulators developed for the description of the behavior of hydrates under production and the corresponding flow of fluids and heat accounting for all known processes are powerful, but they need validation through comparison to field or experimental data in order to instill confidence in their predictions. In this study, we analyze by means of numerical simulation the results of an experiment of methane hydrate dissociation by thermal stimulation in unconsolidated porous media heated through the vessel walls. The physics captured by the model include multicomponent heat and mass transfer, multiphase flow through porous media, and the phase behavior of the CH 4 + H 2 O system involved in methane hydrate formation and dissociation. The set of governing equations consists of the mass and energy conservation equations coupled with constitutive relationships, i.e., the dissolution of gas in H 2 O, relative permeability and capillary pressure models, composite thermal conductivity models, and methane hydrate phase equilibria. The model geometry describes accurately the hydrate reactor used in a recent experimental study investigating methane hydrate dissociation behavior [Chong et. al. Appl. Energy 2016, 177, 409-421]. The cumulative gas production is estimated and validated against three tests of experimental data involving different boundary temperatures, showing a good agreement between observations and numerical predictions. The predicted evolution of the spatial distributions of different phases over time shows that hydrate dissociation progresses inward from the reactor boundary to the center, methane gas accumulates to the top of the reactor because of buoyancy, and water migrates down to the bottom of the reactor because of gravity. A sharp hydrate dissociation front is predicted, and the estimated location of hydrate dissociation front suggests a linear relationship with the square root of time. A sensitivity analysis on the thermal conductivity of sand under fully saturated conditions is conducted to elucidate its effect on the gas production behavior. In addition, the energy efficiency ratio computed from the simulation of this boundary-wall heating technique varies from 14.0 to 16.2. Deviations between observations and predictions of the evolution of the temperature profile are attributed to initial heterogeneous distribution of the hydrate phase in the hydrate reactor.

42 ENGINEERING↗