Search NASA⌕ Search

SEARCH · Search NASA

Results for “Release device”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Experiments on water/melt explosions, nature of products, and models of dispersal

Experiments were carried out in a steel pressure device using controlled amounts of water and thermite melt to examine the mechanical energy released on explosive mixing following the initial contact of the two materials. An experimental design was used to allow the direct calculation of the mechanical energy by the dynamic lift of the device as recorded both optically and physically. A large number of experiments were run to accurately determine the optimum mixture of water and melt for the conversion of thermal to mechanical energy. The maximum efficiency observed was about 12% at a water/thermite mass ratio of 0.50. These experiments are the basis for the development of models of hydroexplosions and melt fragmentation. Particles collected from the experimental products are similar in size and shape to pyroclasts produced by much larger hydrovolcanic explosions. Melt rupture at optimum ratios produces very fine particles whereas rupture at high or low water/melt ratios produces large melt fragments. Grain surface textures in the experimental products are also related to the water/melt ratio and the mechanism of explosive mixing. It is thus possible to have qualitative information about the nature of the explosion from the sizes and shapes of the fragments produced.

Sheridan, M. F.↗
DOE OSTI2025

Supramolecular Control of Ionic Retention in Electrolyte-Gated Synaptic Transistors

Electrolyte-gated transistors with ion-trapping layers offer a promising platform for artificial synapses in neuromorphic computing, yet molecular mechanisms governing ionic retention remain poorly understood. Here, in this study, we present a supramolecular approach to modulate ion retention by incorporating a crown ether derivative-based polymer network as an ion-trapping layer on top of a semiconducting monolayer. We show that the balance between ion–host binding and ion–solvent interactions dictates the kinetics of ion capture and release, which in turn controls the memory characteristics of the device. By varying the solvent dielectric constant, we tune the ionic retention time from nearly permanent trapping to rapid relaxation. Intermediate solvent polarity enables programmable short- and long-term synaptic behaviors, including excitatory postsynaptic current, paired-pulse facilitation, and long-term potentiation and depression. These findings establish a direct link between supramolecular ion recognition and synaptic plasticity and provide a generalizable design strategy for ionic–electronic neuromorphic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Redox-Responsive, Reconfigurable All-Liquid Constructs

Using host-guest chemistries in a biphasic system, a novel supramolecular nanoparticle surfactant (s-NPS) with redox-responsiveness is presented to structure liquids. Additionally, the in situ assembly/jamming and disassembly/unjamming of s-NPSs at the oil-water interface are reversibly controlled by a switchable redox process, imparting a nanoscale redox-responsiveness, affecting the assemblies on all length scales. "Smart" all-liquid constructs including structured emulsions and programmable liquid devices are easily prepared, showing promising applications in responsive delivery, release, and reaction systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Dynamic deuterium retention properties of tungsten measured using laser-induced breakdown spectroscopy

Dynamic deuterium (D) retention properties of tungsten (W) are investigated under steady-state D plasma exposure in the PISCES-A linear plasma device. In contrast to static retention, dynamic retention is quickly released from the material at the termination of the incident plasma flux, and thus in-operando laser-induced breakdown spectroscopy (LIBS) measurements have been conducted during steady-state D plasma exposure. A procedure is, first, established to extract the dynamic retention component from the in-operando LIBS D I 656.1 nm line intensity, which can contain contributions from dynamic and static retention as well as background D/D 2 gas, excited by both steady-state and laser-induced plasmas. Using the developed procedure, the dynamic D retention in W is systematically examined while scanning the following plasma exposure parameters: incident ion energy, E i , sample temperature, T s , incident ion flux, Γ i . No clear E i dependence is seen in the range of E i ~ 45–175 eV, as expected from a small variation in the average implantation depth (~3-6 nm) of D in W. The dynamic retention is found to monotonously decrease with increasing T s from 348 to 573 K, while the total static retention is reported to peak at T s ~ 500–600 K. It is revealed that the dynamic retention linearly increases with increasing Γ i , and then saturates at Γ i ≥ 0.75 × 10 21 m –2 s –1 . Possible physical mechanisms for the observed dependence of the dynamic retention on T s and Γ i are discussed. Furthermore, sequential pure He, followed by pure D, plasma exposures show that the dynamic D retention is not strongly affected by He bubbles in the near-surface region.

super-saturated surface layer↗
DOE OSTI2023

Trace Element Sampling and Partitioning Modeling to Estimate Wastewater Composition and Treatment Performance at Coal Generators

The coal combusted at coal-fired power plants (CFPPs) contains several trace elements that impact human heath if released to the environment. Effective combinations of air pollution control devices (APCDs) and water pollution control devices (WPCDs) are critical to reducing these impacts. This work sampled pulverized CFPPs owned and operated by Louisville Gas & Electricity – Kentucky Utilities (LGE-KU) during baseload and cycling conditions. Next, an open-source and easy-to-implement trace element partitioning model was developed using publicly available datasets, literature studies of trace element partitioning, and sampling data to estimate trace element partitioning in APCDs to the gas, liquid, and solid phases exiting CFPPs. These estimates of the liquid phase trace element concentration in FGD wastewater were then used to estimate trace element behavior in WPCDs and evaluate treated wastewater effluent concentrations for compliance with the Effluent Limitation Guidelines (ELG) for the Steam Electric Generating Sector. Finally, cost estimates were developed for established and emerging wastewater treatment trains to identify the most cost-effective approaches for ELG compliance.

01 COAL, LIGNITE, AND PEAT↗
NASA NTRS1970

Improved solid state electron-charge-storage device

Storage device is applicable in memory systems and in high-resolution arrays for light-responsive image sensing. The device offers high yield in multiple arrays and allows charge release with light striking only the edge of a metal electrode.

Kuper, A. B.↗
NASA NTRS2020

State of the Art Small Spacecraft Technology

When the first edition of NASA’s Small Spacecraft Technology State-of-the-art report was published in 2013, 247 CubeSats and 105 other non-CubeSat small spacecraft under 50 kilograms (kg) had been launched, and these represented less than 2% of launched mass into orbit. By 2019, small spacecraft with mass less than 180 kg made up almost 7% of all mass launched into orbit. Additionally, 63% of spacecraft under 600 kg had mass less than 180 kg and of those 47% were CubeSats (1). Since 2013, flight heritage for small spacecraft, primarily CubeSats, has nearly doubled and with dedicated smallsat launch capabilities readily available and expanding, opportunities to demonstrate new technologies and systems are expected to increase. The 2020 edition of this report captures and distills the wealth of new information available on small spacecraft systems from NASA and other publicly available sources. Overall, this report is a survey of small spacecraft technologies sourced from open literature; it does not endeavor to be an original source, and only considers literature in the public domain to identify and classify devices. Commonly used sources for data include manufacturer datasheets, press releases, conference papers, journal papers, public filings with government agencies, news articles, presentations, and Small Spacecraft Systems Virtual Institute Federated Search. Data not appropriate for public dissemination, such as proprietary, export controlled, or otherwise restricted data, are not considered. As a result, this report includes many dedicated hours of desk research performed by subject matter experts reviewing resources noted above.

Bruce Yost↗
DOE OSTI2020

Pipe restraint and shield

A pipe restraint assembly includes a restraint body configured to be removably attached to a portion of pipe. The portion of pipe is associated with a postulated pipe failure associated with a release of high pressure fluid. A plurality of apertures penetrate through the restraint body and are positioned proximate to a location of the postulated pipe failure. The apertures are configured to provide a number of passageways for the fluid to exit from the location of the postulated pipe failure and to be released outside of the restraint body. One or more restraint devices maintain the position of the apertures relative to the location of the postulated pipe failure.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

New Modulation and Impact of Transformer Leakage Inductance on Current-Source Solid-State Transformer

This article presents a novel modulation scheme for device voltage stress mitigation and comprehensive analysis of the impact of transformer leakage inductance in a current-source solid-state transformer (SST). Different from dual active bridge (DAB) SST, the operation of the current-source SST is similar to that of a flyback converter. The device bridge on only one side of the transformer is active to store energy into or release energy from the magnetizing inductance which acts as a current-source dc link. Such flyback operation with reverse-blocking switches can lead to additional device voltage stress and incomplete zero-voltage switching (ZVS) on the current-source soft-switching solid-state transformer (S4T) under conventional modulation. A new modulation scheme is proposed to address this issue. Moreover, different from the DAB, the leakage inductance of the medium-frequency transformer (MFT) in the S4T is a parasitic element similar to that in a matrix SST and can cause additional device voltage stress. Though the resonant capacitors, originally added to achieve ZVS, can absorb and recycle the leakage energy in the S4T, these capacitors need to be increased with larger leakage inductances to limit the voltage stress. However, large resonant capacitors can result in more lost duty cycles and reduced efficiency. The impact of such leakage inductance on device voltage stress is analyzed comprehensively, which is critical to guide future research and design of the S4T. Experimental results from S4T prototypes for DC-DC, multiport AC-DC, and AC-AC conversion with 1:1 and 4:1 MFT comprehensively verify the proposed concepts. Lastly, a case study of a three-phase AC-AC S4T over a power range from 1 kVA to 100 kVA each module reveals that the MFT leakage inductance should be less than 1% of the magnetizing inductance for safe operation.

14 SOLAR ENERGY↗
NASA NTRS2002

Pressure-Application Device for Testing Pressure Sensors

A portable pressure-application device has been designed and built for use in testing and calibrating piezoelectric pressure transducers in the field. The device generates pressure pulses of known amplitude. A pressure pulse (in contradistinction to a steady pressure) is needed because in the presence of a steady pressure, the electrical output of a piezoelectric pressure transducer decays rapidly with time. The device includes a stainless- steel compressed-air-storage cylinder of 500 cu cm volume. A manual hand pump with check valves and a pressure gauge are located at one end of the cylinder. A three-way solenoid valve that controls the release of pressurized air is located at the other end of the cylinder. Power for the device is provided by a 3.7-V cordless-telephone battery. The valve is controlled by means of a pushbutton switch, which activates a 5 V to +/-15 V DC-to-DC converter that powers the solenoid. The outlet of the solenoid valve is connected to the pressure transducer to be tested. Before the solenoid is energized, the transducer to be tested is at atmospheric pressure. When the solenoid is actuated by the push button, pressurized air from inside the cylinder is applied to the transducer. Once the pushbutton is released, the cylinder pressure is removed from the transducer and the pressurized air applied to the transducer is vented, bringing the transducer back to atmospheric pressure. Before this device was used for actual calibration, its accuracy was checked with a NIST (National Institute of Standards and Technology) traceable calibrator and commercially calibrated pressure transducers. This work was done by Wanda Solano of Stennis Space Center and Greg Richardson of Lockheed Martin Corp.

Source record↗
DOE OSTI2020

The Sensitivity of Chemical Kinetic Models on Flame Transfer Functions in Acoustic Fluctuation Environments with Varying Equivalence Ratios

Various factors affect the heat release response of flames – thermodynamics, hydrodynamics, acoustics, etc. The coupling of heat release rate and acoustics, in particular, is essential to the design of combustion devices so as to avoid adverse effects during their operation. Modeling flames in acoustic environments requires an accurate understanding of the fundamental physics that occurs when flames interact with a fluctuating pressure field. Over the past couple of decades, researchers have been quantifying the impact of this fluctuating pressure field on the unsteady heat release rate. The flame transfer functions computed have also been shown to depend on the level of detail in the chemical kinetic model. This paper attempts to bridge the gap between these studies to understand how sensitive the flame transfer function is to various kinetic models. The problem is studied by performing multiple one-dimensional simulations using the low-Mach solver NGA. The detailed GRI-Mech 3.0 will be used for comparison. Also, the pressure amplitude and reactant equivalence ratio are varied to understand how the environment affects this sensitivity.

Girdhar, Anant↗
DOE OSTI2020

Selective-Area Remote Epitaxy of ZnO Microrods Using Multilayer–Monolayer-Patterned Graphene for Transferable and Flexible Device Fabrications

Here, selective-area remote epitaxy (SA-REpi) is demonstrated for fabricating mechanically releasable position-controlled ZnO microrod (MR) arrays from donor wafers in an arrayed form. Intaglio-patterned graphene, consisting of basal single-layer graphene (SLG) overlayered with multilayer graphene (MLG) patterned with perforated holes, is transferred onto a GaN/Al 2 O 3 wafer on which the hydrothermal synthesis is performed for growing ZnO MRs. The basal SLG area exposed through the MLG pattern yields ZnO MRs, whereas the MLG plateau inhibits the growth. The noncovalent remote epitaxial heterointerface enables the release of the MR overlayer in the arrayed form, and the original source wafer is refurbished for reproducibly repeating the SA-REpi. Density-functional theory calculations suggest that localized surface charge density is induced on the surface of SLG by the underlying GaN across ultrathin SLG, which possibly provides a driving force for precursor adatoms and the following remote epitaxy of ZnO. In contrast, the induction of the charge density redistribution does not clearly occur through MLG; so, that keeps the surface of MLG nearly charge-neutral. The diameter and spacing of ZnO MRs are controlled in a designed way by changing the pattern geometries. High-resolution scanning transmission electron microscopy reveals the remote heteroepitaxial relationship at an atomic level. The remote epitaxy is expected to provide an ideal platform to transfer the addressable spatial arrays of nano- or micro-architecture semiconductor components to arbitrary target surfaces directly after the growth without the assembly procedures.

36 MATERIALS SCIENCE↗
NASA NTRS2009

Apollo Spacecraft and Saturn V Launch Vehicle Pyrotechnics/Explosive Devices

The Apollo Mission employs more than 210 pyrotechnic devices per mission.These devices are either automatic of commanded from the Apollo spacecraft systems. All devices require high reliability and safety and most are classified as either crew safety critical or mission critical. Pyrotechnic devices have a wide variety of applications including: launch escape tower separation, separation rocket ignition, parachute deployment and release and electrical circuit opening and closing. This viewgraph presentation identifies critical performance, design requirements and safety measures used to ensure quality, reliability and performance of Apollo pyrotechnic/explosive devices. The major components and functions of a typical Apollo pyrotechnic/explosive device are listed and described (initiators, cartridge assemblies, detonators, core charges). The presentation also identifies the major locations and uses for the devices on: the Command and Service Module, Lunar Module and all stages of the launch vehicle.

Interbartolo, Michael↗
NASA NTRS1968

High efficiency, high frequency magnetic deflection driver

Electromagnetic deflection yoke stores energy during the scan and releases it in the flyback or retrace. The operation of the device involves a method of switching to a voltage high enough to dissipate the flyback pulse during the retrace time and then operating during the scan time at a much lower voltage.

Schaff, F. L.↗
NASA NTRS2006

Modern Space Craft - Antique Specifications

Spacecraft now and of the future are being controlled by EMC requirements of the past. Little has been done by the launch vehicle/spacecraft manufacturers to abandon MIL-STD-461C which was released in 1986 because most of the electronics equipment being used aboard current launch vehicles is approved by similarity and heritage to MIL-STD-46 1 C and its predecessors. Twenty years later these electronic equipment items are still not tested to today's MIL-STD-461E requirements because there is a risk that the items will fail to meet the requirements and thus the cost will increase if it becomes necessary to redesign the equipment. That cost is insignificant compared with the cost of losing an entire mission! In the 20 years that have elapsed since MIL-STD-461C was released, the EMC environment has undergone major changes. High speed digital devices have been created that have fundamental clock and bus frequencies that span the entire LV/SC frequency range from the Flight Termination Systems through C and S-Band telemetry. Personnel involved in ground operations routinely carry and use hand held transceivers and cellular telephones close by sensitive electronics equipment. There are now many more orbiting receivers and emitters, plus range assets have increased dramatically since 2001. It's way past time to bring requirements up-to-date!

Brewer, Ron↗
NASA NTRS2019

Combining Fractional Calorimetry with Statistical Methods to Characterize Thermal Runaway

Fractional thermal runaway calorimetry (FTRC) techniques were introduced to examine thermal runaway (TR) behavior of lithium-ion (Li-ion) cells. Specifically, FTRC considers the total energy released vs. the fraction of the total energy that is released through the cell casing vs. through the ejecta material. This device has been expanded to universally support FTRC testing of additional cell types including 21700-format, D-Cell format, and large prismatic format Li-ion cells. The TR behavior as influenced by cell format, manufacturer, chemistry, capacity, and in situ safety features are described in this presentation.

Walker, William↗
DOE OSTI2022

Recent Developments in the WEC-Sim Open-Source Design Tool: Preprint

WEC-Sim (Wave Energy Converter SIMulator) is an open-source code for simulating wave energy converters, which has been actively developed and applied to simulate a wide variety of device archetypes and has become a popular tool since its initial release in 2014. WEC-Sim is developed jointly by the National Renewable Energy Laboratory (NREL) and Sandia National Laboratories (SNL) within the MATLAB/SIMULINK environment. Figure 1 illustrates a general wave-to-wire model which begins with a deployment site resource characterization, which is used to complete the hydrodynamic simulation of a single WEC (or array), with the power generation profile imported to a grid simulator to understand the influence on the local electrical network. While modelling the entire wave-to-wire is difficult and encompass multiple time scales and physics, WEC-Sim is focused on the hydrodynamics simulation to predict, analyze and optimize WEC dynamics and power performance. WEC-Sim simulations are performed in the time domain based on the radiation and diffraction method using hydrodynamics coefficients derived from boundary element method (BEM) based-frequency-domain potential flow solvers (e.g., WAMIT, NEMOH, Capytaine, or ANSYS-AQWA). Within this level of modeling fidelity, WEC-Sim can handle floating body hydrodynamics, mechanical and electrical power generation methods, advanced control implementation, mooring systems, and other unique applications such as desalination. Table 1 lists additional WEC-Sim functionalities, which are created using prebuilt Simulink blocks and MATLAB scripts that can simulate a wide range of floating systems and the corresponding auxiliary subsystems.

hydrodynamics modeling↗