Search NASA⌕ Search

SEARCH · Search NASA

Results for “Resistive Anode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Synthetic sea water - An improved stress corrosion test medium for aluminum alloys

A major problem in evaluating the stress corrosion cracking resistance of aluminum alloys by alternate immersion in 3.5 percent salt (NaCl) water is excessive pitting corrosion. Several methods were examined to eliminate this problem and to find an improved accelerated test medium. These included the addition of chromate inhibitors, surface treatment of specimens, and immersion in synthetic sea water. The results indicate that alternate immersion in synthetic sea water is a very promising stress corrosion test medium. Neither chromate inhibitors nor surface treatment (anodize and alodine) of the aluminum specimens improved the performance of alternate immersion in 3.5 percent salt water sufficiently to be classified as an effective stress corrosion test method.

Humphries, T. S.↗
NASA NTRSDate not supplied

Feasibility Testing of Silver Electrolysis for Disinfection of Spacecraft Potable Water Systems

Anodic dissolution of silver electrodes, or “silver electrolysis,” is being investigated as a means of introducing biocidal silver into potable water on exploration spacecraft. A proof-of-concept prototype of a silver electrolysis reactor was developed, and feasibility was demonstrated for imparting a target silver concentration into a spacecraft water system. Prototype testing showed that the primary initial concerns related to the technology - inefficiencies of electrolysis in low conductivity water, the potential formation of resistive oxides on the electrode surfaces, and the potential for release of electrolytically-generated silver particles to the effluent water - were not problematic over the duration of the feasibility testing. The testing also demonstrated advantages of the technology, including the ability to consistently deliver silver at targeted concentrations and the ability to directly correlate the silver concentration to measurements of water conductivity. On the other hand, the reliability of the system has not yet been demonstrated. During prototype testing, intermittent periods of poor reactor performance manifested as a decrease in voltage accompanied by a decrease in silver output. It was determined that the cause of this behavior was silver-based deposits on inter-electrode wetted surfaces forming a conductive “bridge” between electrodes. Ongoing testing and refinement of the prototype reactor design seek to elucidate the root cause the bridging phenomenon and identify associated mitigation strategies. Once resolved, long-term performance testing is planned as part of continued development of the electrolytic silver dosing system.

Silver↗
DOE OSTI2025

Highly textured metal anodes for stable aqueous batteries: Fabrication and characterization

We report a purely mechanical “cold-compression flow” method for fabricating Zn, Sn, and In substrates with tunable crystallographic textures. Using textured Zn as a model system, we investigate Zn electrocrystallization and demonstrate correlated growth of crystalline films with correlation lengths from tens to hundreds of micrometers. At 5 milliamperes per square centimeter (mA/cm 2 ), capacities between 20 and 82 milliampere hours per square centimeter (mA·hour/cm 2 ) are achieved depending on substrate texture level. At higher currents (40 mA/cm 2 ), capacities reach up to 604 mA·hour/cm 2 . Rotating disk electrode studies show that dominantly (002) textured Zn substrates exhibit enhanced corrosion resistance and reduced interphase passivation. We introduce an effective Damköhler number (Da*) to concisely describe morphological evolution during electrocrystallization across substrates with different textures. High-texture (002) Zn substrates substantially enhance performance in high-capacity (~20 mA·hour/cm 2 ) symmetric Zn||Zn cells and full cells (Zn||δ-MnO 2 and Zn||I 2 ), enabling fast-charging and prolonged energy storage in coin and pouch rechargeable Zn battery formats.

Science & Technology - Other Topics↗
NASA NTRS1990

Characterization of the corrosion resistance of several alloys to dilute biologically active solutions

Sulfate reducing bacteria and acid producing bacteria/fungi detected in hygiene waters increased the corrosion rate in aluminum alloy. Biologically active media enhanced the formation of pits on metal coupons. Direct observation of gas evolved at the corrosion sample, coupled with scanning electron microscopy (SEM) and energy dispersive x-ray analysis of the corrosion products indicates that the corrosion rate is increased because the presence of bacteria favor the reduction of hydrogen as the cathodic reaction through the reaction of oxygen and water. SEM verifies the presence of microbes in a biofilm on the surface of corroding samples. The bacterial consortia are associated with anodic sites on the metal surface, aggressive pitting occurs adjacent to biofilms. Many pits are associated with triple points and inclusions in the aluminum alloy microstructure. Similar bacterial colonization was found on the stainless steel samples. Fourier transform Infrared Spectroscopy confirmed the presence of carbonyl groups in pitted areas of samples exposed to biologically active waters.

Walsh, Daniel W.↗
NASA NTRS1995

Recent results from Long Duration Exposure Facility materials testing

The overall goals of the Long Duration Exposure Facility (LDEF) investigations, established by the Materials Special Investigation Group (MSIG) prior to LDEF retrieval, are to provide useful engineering data to people designing and building spacecraft, and secondarily, to obtain data of potential interest to materials researchers. The specific objectives are to support predictions of materials lifetimes under the various low earth orbit (LEO) environments to determine how long the material will physically survive; to estimate the engineering performance lifetimes of these same materials under specific LEO exposures; to identify materials and processes by which given materials degrade; and to provide insights into development of new, more inherently LEO environmentally resistant materials. To achieve the established objectives, two criteria were established to select which materials had the highest priorities for analyses. The first criteria was to examine materials which are still being used on new spacecraft. The second priority was to examine materials with multiple exposure locations on LDEF, because this provided the opportunity to develop predictions on how a material will behave as the exposure environment varies. The goals as defined led to the identification of silverized Teflon (Ag/FEP), chromic acid anodized aluminum, and certain thermal control paints used on LDEF as the material types of highest priority for examination. Ag/FEP was chosen because of an excellent a/e ratio (extremely low), and extensive flight history. Also influencing the decision was the fact that the Hubble Space Telescope uses Ag/FEP as its primary passive thermal control system (and was launched shortly after LDEF retrieval) and that a number of other spacecraft are using or considering this material for use. The various forms of Ag/FEP were used on virtually every side of the LDEF except the earth end. The potential uses of this material, and the location distribution and therefore, exposure conditions, have provided the rationale and opportunity for a comprehensive study of this material.

Pippin, H. Gary↗
DOE OSTI2025

Investigating the impact of preparation routes on the properties of copper-decorated silicon particles as anode materials for lithium-ion batteries

In recent years, the calendar life of Si has been recognized as a significant issue that must be addressed prior to technology deployment: The carbon conductive additive is a potential source of parasitic side reactions. However, carbon remains essential due to the low electronic conductivity of Si. In this study, we investigate the use of Cu as a conductive additive and potential alternative to carbon. Some Cu-decorated silicon particles (Si Cu ) were prepared using physical vapor deposition (PVD) via sputtering and high-energy milling. Other Si Cu particles were prepared by using a solution method and examined briefly. The milling method caused Cu to appear as island-like features on the Si surface, whereas the PVD method initially produced similar island-like features that gradually developed into a continuous coating around the Si as sputtering time increased. Electrodes fabricated from Si Cu exhibited lower overall resistivity, demonstrating the beneficial effect of Cu in improving electronic percolation through the electrode. Electrochemical tests showed that the milled SiCu exhibited higher capacity retention, improved rate capability, and lower overpotential. Furthermore, Si Cu coupled with an NMC811 cathode exhibited lower leakage currents compared with the baseline silicon, indicating that incorporating Cu provided an additional advantage of minimizing parasitic currents in the cells.

25 ENERGY STORAGE↗
NASA NTRS2019

A Multi-Physics Study on High-Specific Power Li-O2 Batteries for Electric Aircraft

Commercialization of lithium-air batteries faces many challenges, such as electrolyte decomposition, short cycle life, low energy and power density, etc. However, commercialization of Li-O2 batteries for aeronautics is much more challenging due to additional safety constraints on cyclability and performance (high specific power and specific energy). For this presentation, we will discuss inter-related aspects of physics-based modeling of a pack: cell and battery model calibration. In addition, we will evaluate and present optimal battery designs for high discharge current density, high discharge time, and low battery mass using simulation-based optimization.The Finite Element Model (FEM) used to simulate a Li-O2 cell is based on the work of Bevara [1]. The different aspects of the model are based on: porous electrode theory and concentrated electrolyte theory; quantum tunneling model for the resistance of conformal layer of discharge product (Li2O2) [1]; Butler-Volmer kinetics for electrochemical reaction; Fick's diffusion for oxygen transport; and an oxygen dissolution model is applied at the air/electrolyte interface [2]. The electrolyte properties such as ion conductivity, ion diffusion, oxygen diffusion, and mass density of the electrolyte were taken from Molecular Dynamics (MD) simulations [3]; while the other model parameters, which includes mass of cell components, were calibrated to match experiments at high discharge current densities. The cell mass includes the anode, cathode, separator, electrolyte, and other components (such as current collector). This calibrated model is used to perform parametric studies on cathode thickness, porosity, tortuosity, carbon particle size, electrolyte transport and material properties, partial pressure of oxygen, discharge time, and discharge current density to study optimal designs for high specific power and energy. References:1. Bevara, V. & Andrei, P. (2014), J. Electrochem. Soc. 161 (14), A2068-A2079.2.Mehta, M. & Andrei, P. (2015), J. Power Sources. 286, 299-308.3.Liyana-Arachchi, T.; Haskins, J.; Burke, C.; Diederichsen, K.; McCloskey, B.; & Lawson, J. (2018), J. Phys. Chem. B. 122 (36), 8548 - 8559.4.Choi, W.; Kikumoto, H.; Choudhary, R. & Ooka, R. (2018), Applied Energy, 209, 306-321.

Mehta, Mohit↗
DOE OSTI2025

Interlayer Design for Halide Electrolytes in All‐Solid‐State Lithium Metal Batteries

Abstract All‐solid‐state lithium‐metal batteries (ASSLMBs) are promising for transportation electrification due to their superior safety and high energy density. Lithium halide electrolytes provide excellent processing flexibility, high ionic conductivity, and anodic stability (>4.1 V), making them highly compatible with high‐voltage cathodes, surpassing sulfide electrolytes (<2.1 V). Nevertheless, halide electrolytes suffer from low cathodic stability and form an electronically conductive interphase with lithium, resulting in a critical current density (CCD) of nearly zero. Herein, Li 3 YbCl 6 electrolytes are synthesized that are kinetically stable with lithium by forming an electronic insulating solid electrolyte interphase. Guided by critical overpotential criteria, a PI 3 interlayer is designed that transforms into Li 6 PI 3 upon contact with lithium, substantially reducing the interfacial resistance of Li 3 YbCl 6 against lithium to 34 Ω and achieving a high critical overpotential of 114 mV. By substituting Yb with Lu, Li 3 LuCl 6 electrolytes with Li 6 PI 3 interlayers reach a CCD of 1.0 mA cm −2 at a capacity of 1.0 mAh cm −2 , comparable to sulfide electrolytes but with higher oxidation stability. Additionally, Li 6 PI 3 enables stable cycling of Li//Li cells with Li 3 LuCl 6 electrolytes at 0.5 mA cm −2 for 400 cycles and maintains 86.5% capacity in Li//LiCoO 2 cells after 220 cycles at 30 °C, paving the way for high‐performance ASSLMBs.

Chemistry↗
DOE OSTI2026

Impact of Fermentation-Derived Substrates on Hydrogen Production in Zero-Gap Microbial Electrolysis Cells

Zero-gap microbial electrolysis cells (MECs) represent a promising platform for hydrogen production from liquid waste streams due to reduced interelectrode spacing that lowers internal resistance and enhances mass transport. However, the performance and stability of zero-gap MECs treating chemically complex feedstocks remain insufficiently characterized. Here, we operated zero-gap MECs with real, unamended, corn stover dark fermentation effluent containing a wide range of organic substrates. The MECs fed fermentation effluent achieved a maximum current density of 24 A/m2 (15+-6 A/m2 over the cycle) and a hydrogen production rate of 75 L/L-d (42+-19 L/L-d over the cycle). The substrates were consumed at different rates, indicating substrate-selective utilization by the anodic microbial community. Acetate supported high and stable current generation, whereas ethanol, formate, lactate, and amino acids induced varying degrees of inhibition depending on their concentration. Residual sugars caused pronounced current fluctuations, consistent with ongoing fermentation and local pH changes. A diverse microbial community was crucial for efficiently utilizing complex organics and maximizing electrochemical performance. These results demonstrate how and to what extent substrate composition regulates zero-gap MEC performance and that microbial community and operational conditions can be leveraged to enhance performance. These novel findings provide practical guidance for achieving robust hydrogen recovery from chemically heterogeneous real liquid waste streams.

08 HYDROGEN↗
DOE OSTI2023

Interface Design for High‐Performance All‐Solid‐State Lithium Batteries

All‐solid‐state batteries suffer from high interface resistance and lithium dendrite growth leading to low Li plating/stripping Coulombic efficiency (CE) of <90% and low critical current density at high capacity. Here, in this work, both challenges are simultaneously addressed and the Li plating/stripping CE is significantly increased to 99.6% at 0.2 mA cm −2 /0.2 mAh cm −2 , and critical current density (CCD) of > 3.0 mA cm −2 /3.0 mAh cm −2 by inserting a mixed ionic‐electronic conductive (MIEC) and lithiophobic LiF‐C‐Li 3 N‐Bi nanocomposite interlayer between Li 6 PS 5 Cl electrolyte and Li anode. The highly lithiophobic LiF‐C‐Li 3 N‐Bi interlayer with high ionic conductivity (10 −5 S cm −1 ) and low electronic conductivity (3.4×10 −7 S cm −1 ) enables Li to plate on the current collector (CC) surface rather than on Li 6 PS 5 Cl surface avoiding Li 6 PS 5 Cl electrolyte reduction. During initial Li plating on CC, Li penetrates into porous LiF‐C‐Li 3 N‐Bi interlayer and lithiates Bi nanoparticles into Li 3 Bi. The lithiophilic Li 3 Bi and Li 3 N nanoparticles in LiF‐C‐Li 3 N‐Li 3 Bi sub‐interlayer will move to CC along with plated Li, forming LiF‐C/Li 3 N‐Li 3 Bi lithiophobic/lithiophilic sublayer during the following Li stripping. This interlayer enables Co 0.1 Fe 0.9 S 2 /Li 6 PS 5 Cl/Li cell with an areal capacity of 1.4 mAh cm −2 to achieve a cycle life of >850 cycles at 150 mA g −1 . The lithiophobic/lithiophilic interlayer enables solid‐state metal batteries to simultaneously achieve high energy and long cycle life.

25 ENERGY STORAGE↗
DOE OSTI2026

Correlating surface adsorbate configuration and electrochemical performance of IrO 2 during seawater-relevant electrolysis

Seawater electrolysis alleviates freshwater demand to produce clean hydrogen while eliminating the need for water purification steps. The anodic process, seawater oxidation, typically requires high overpotentials and yields low selectivity to oxygen via the oxygen evolution reaction (OER), primarily due to the competing chlorine evolution reaction (CER) and hypochlorite evolution reaction (HCER) in pH-neutral conditions. Here, combining in situ surface-enhanced Raman characterization, grand canonical density functional theory-based calculations, and kinetic Monte Carlo simulations, we report the evolution of surface adsorbate configurations driven by applied potential and pH during seawater-relevant OER over IrO 2 , a highly OER-active and chloride-corrosion-resistant catalyst. As a result, the chemical properties of active sites, and thereby the kinetics of OER and CER/HCER, are effectively tuned. However, it is revealed that there is no optimal combination of potential and pH to achieve both high activity and high selectivity for seawater-relevant OER. To address this limitation, we establish a correlation between activity/selectivity and surface adsorbate configurations, enabling the optimization of highly active and OER-selective IrO 2 -based catalysts in seawater-relevant oxidation by modulating the local adsorbate environment of active sites.

08 HYDROGEN↗
DOE OSTI2026

Unlocking the Future of Aircraft Manufacturing: The Environmental Benefits of Laser Patterning for Surface Enhancement of Aircraft-Certified Alloys

Surface protection and functional modification of aircraft-certified aluminum alloys are essential for corrosion resistance, durability, and long-term airworthiness. At the same time, increasingly restrictive environmental regulations motivate the development of alternatives to legacy wet-chemical surface treatments. This study presents an integrated assessment of ultrafast femtosecond laser surface texturing as a surface functionalization approach for Aluminum 6061 alloys within an aerospace manufacturing and sustainability context. Ultrashort-pulse laser processing enables controlled micro- and nano-scale surface topographical modification with limited thermal impact, allowing adjustment of wettability and surface functionality while preserving bulk material integrity. As a dry and contactless process, femtosecond laser treatment eliminates the use of hazardous chemicals, reduces consumable inputs, and generates minimal secondary waste. A streamlined cradle-to-gate life cycle assessment conducted in accordance with ISO 14040/14044 indicates a lower global-warming potential per functional unit compared with conventional surface treatments, including anodization, plasma-assisted coatings, and organic coating systems. Complementary qualitative analyses addressing environmental health and safety, supply-chain risk, and ESG alignment indicate potential advantages related to occupational safety, regulatory compliance, waste management, and end-of-life recyclability. The investigation is performed on planar Aluminum 6061 reference surfaces with a treated area of 25 mm 2 , providing a controlled laboratory-scale basis for analyzing process behavior, functional surface modification, and associated environmental metrics. Within this defined scope, the results support further evaluation of femtosecond laser surface texturing as a surface engineering option for future aerospace manufacturing.

corrosion resistance↗
NASA NTRS2014

Effects of Low Earth Orbit on Docking Seal Materials

Spacecraft docking seals are typically made of silicone elastomers. When such seals are exposed to low Earth orbit (LEO) conditions, they can suffer damage from ultraviolet (UV) radiation and atomic oxygen (AO, or monoatomic oxygen, the predominant oxygen species in LEO). An experiment flew on the International Space Station (ISS) to measure the effects of LEO on seal materials S0383-70 and ELA-SA-401 and various mating counterface materials which included anodized aluminum. Samples flown in different orientations received different amounts of UV and AO. The hypotheses were that most of the damage would be from UV, and 10 days or more of exposure in LEO would badly damage the seals. Eighteen seals were exposed for 543 days in ram (windward), zenith (away from Earth), or wake (leeward) orientations, and 15 control samples (not flown) provided undamaged baseline leakage. To determine post-flight leak rates, each of the 33 seals were placed in an O-ring groove of a leak test fixture and pressure tested over time. Resistance temperature detectors (RTDs), pressure transducers, and LabVIEW (National Instruments) programs were used to measure and analyze the temperature and pressure and calculate leakage. Average leakage of control samples was 2.6 x 10(exp -7) lbs/day. LEO exposure did not considerably damage ELA-SA-401. The S0383-70 flight samples leaked at least 10 times more than ELA-SA-401 in all cases except one, demonstrating that ELA-SA-401 may be a more suitable sealing material in LEO. AO caused greater damage than UV; samples in ram orientation (receiving an AO fluence of 4.3 x 10(exp 21) atoms/(sq cm) and in wake (2.9x 10(exp 20) atoms/(sq cm)) leaked more than those in zenith orientation (1.58 x 10(exp 20) atoms/(sq cm)), whereas variations in UV exposure did not seem to affect the samples. Exposure to LEO did less damage to the seals than hypothesized, and the data did not support the conjecture that UV causes more damage than AO.

Leakage↗
DOE OSTI2024

Fast timing with µRWELL-PICOSEC detector technology

The µWELL-PICOSEC detector, which is based on Resistive Micro-Well (µRWELL) technology, is a novel concept for fast timing gaseous detectors that can provide timing resolution in the tens of picosecond range, making it ideal candidate for time-of-flight (TOF) technology for particle identification (PID) in particle physics experiments as well as for future medical instrumentation. The µRWELL-PICOSEC concept is based on a Cerenkov radiator that produces Cerenkov photons from high energetic charged particles, a photocathode layer that converts the Cerenkov photons into primary electrons, a µRWELL amplification layer that multiply the electrons through amplification in a CF4-based gas mixture and a pad-segmentation anode readout coupled with fast timing electronics to provide fast signal. Beam tests were carried out at the CERN SPS H4 beamline in summer 2023 and 2024. Preliminary results show timing performance of the order of 23 ps achievable with µRWELL-PICOSEC prototype. and position scan of the 100-pads of a multi-channel prototype was also performed to study time response uniformity of large area detector. In this talk, after a brief overview of the PICOSEC technology, we will present recent results with different single channel µRWELL-PICOSEC prototype designs and also the position scan results of the 100-pads large prototype to study timing response uniformity for large area µRWELL-PICOSEC detector. Finally, we will discuss the ongoing R&D effort to further improve the timing resolution and allow good position capabilities through charge sharing for large area.

Gnanvo, Kondo↗
NASA NTRSDate not supplied

Design Considerations for Practical Li-S Batteries for Electric Aviation

The development of high-energy, high-safety, and high-power batteries beyond electric automotive standards is critical for future electric aviation applications. Non-volatile solid-state electrolytes (SSE) offer many promising advantages over traditional flammable liquid electrolytes. Solid-state electrolytes may be an enabling technology for certain battery chemistries by preventing detrimental interactions with liquid electrolytes, for example prevention of the dissolution of intermediates in lithium-sulfur common in traditional liquid organic solvents. However, significant manufacturing challenges must be overcome before the adoption of such technology. This research was conducted to identify processing techniques for producing solid-state battery components with practical dimensions and weights for enabling high specific energy cells. Traditional research has identified a range of very high theoretical ionic conductivities but are impractical due to their instability or inability to be manufactured. Electrolytes explored in this study were produced as sulfide-polymer composites with densified thicknesses below 40 micron using a tape-casting technique and thermoplastic elastomer binder. The combination of high chemical compatibility and flexibility produced robust films that had moderate impact on the ionic conductivity but was capable of dramatically reducing the parasitic mass. Despite minimal conductivity losses, films were produced 10-15 times thinner than comparable bulk powder electrolytes thus leading to overall lower film resistance. Conductivity is maintained above 0.2mS/cm for composite electrolytes. Through the analysis of materials based on their physical properties, such as density, practical cells can be designed. Based on this, low density sulfide-solid-state electrolytes are a promising candidate for achieving the energy and safety metrics for electric aviation, however, further optimization of cathode microstructure and composite processing will be required to achieve the high power metrics and will be the focus of further studies. Additionally, fabrication challenges arise when utilizing metallic lithium foil, due to its soft nature, as overflow and mechanical short circuit can occur on assembly which remains a challenge to overcome before metallic lithium anodes can be fully realized.

batteries↗
DOE OSTI2024

A Comprehensive Experimental Study on Microstructure‐Graded Graphite Anodes for Enhancing Fast‐Charging Capability of Lithium‐Ion Batteries

Lithium‐ion batteries with high gravimetric capacity density and improved cycle life performance under fast‐charging conditions are crucial for widespread electric vehicle (EV) adoption. This study investigates how designing graphite anode microstructure, specifically porosity, and particle‐size gradients, improves lithium‐ion (Li + ) transport during fast‐charging conditions. Three‐layered graphite anodes with varying porosity (24%, 36%, 46%) and particle size gradients (3, 5, 10 μm) were compared to a conventional single‐layered electrode in half‐cell configurations. At room temperature and high discharge rate (2C), both gradient structures showed significantly enhanced capacity retention (80% and 67% vs. 50%) compared to the conventional electrode, highlighting the effectiveness of microstructure engineering for fast charging. The study also investigated the temperature's impact on cycle life. After 200 cycles at 2°C and 45°C, all gradient structures demonstrated superior capacity retention (≈80%) compared to the conventional electrode (35%), suggesting the gradients mitigate degradation rate at high temperatures. Electrochemical impedance spectroscopy confirmed superior Li+ diffusion and lower resistivity in gradient electrodes. Simulations explored the influence of gradient profiles on reaction kinetics across the electrode thickness. Overall, this research demonstrates that the fast‐charging capability of graphite electrodes can be greatly enhanced by engineering the electrode microstructure, thereby making EV technology more accessible and appealing.

Ahmadi, Soma↗
DOE OSTI2025

Critical Insights into Solvent Choice for High-Voltage Organosulfur Electrolytes

Organosulfur electrolytes are promising candidates for enabling high-voltage cathodes due to their superior oxidative stability compared to conventional carbonate-based systems. However, their viscous nature and inability to passivate the anode necessitate the use of passivating agents and diluents to achieve meaningful charge/discharge rates. In this study, we investigate the use of cyclic fluorinated carbonates (CFCs) to form passivating interphases on electrode surfaces, aiming to optimize electrolyte performance in high-voltage systems. Electrolyte formulations containing 1.2 M LiPF 6 in a CFC:sulfone:1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropylether (TTE) mixture (2/5/3 V/V/V) were assessed in full-cell configurations with a LiNi 0.8 Mn 0.1 Co 0.1 O 2 (FCG-NMC) cathode and a 4.5 V upper cutoff potential. The results reveal that 3-3-3-trifluoropropylene carbonate (TFPC) combined with ethyl methyl sulfone (EMS) optimizes electrolyte performance, resulting in lower resistance buildup and reduced capacity loss compared to commercial electrolytes. We also explore the failure mechanisms of several carbonate/sulfone mixtures and identify key considerations for electrolyte compatibility in high-voltage systems. TFPC enhances cycling stability and lowers overall cell resistance, while fluoroethylene carbonate (FEC) formulations, despite higher ionic conductivity, fail to form adequate passivation layers, leading to rapid capacity loss. Additionally, EMS provides superior physical properties that avoid common failure modes seen with other sulfone solvents like methyl isopropyl sulfone and tetramethylene sulfone. Furthermore, this study underscores the importance of carefully selecting passivating carbonates and sulfone solvents to improve electrolyte performance and expand the viability of high-voltage electrolyte systems.

LiNi0.8Mn0.1Co0.1O2 cathode↗
NASA NTRS2004

Brush/Fin Thermal Interfaces

Brush/fin thermal interfaces are being developed to increase heat-transfer efficiency and thereby enhance the thermal management of orbital replaceable units (ORUs) of electronic and other equipment aboard the International Space Station. Brush/fin thermal interfaces could also be used to increase heat-transfer efficiency in terrestrial electronic and power systems. In a typical application according to conventional practice, a replaceable heat-generating unit includes a mounting surface with black-anodized metal fins that mesh with the matching fins of a heat sink or radiator on which the unit is mounted. The fins do not contact each other, but transfer heat via radiation exchange. A brush/fin interface also includes intermeshing fins, the difference being that the gaps between the fins are filled with brushes made of carbon or other fibers. The fibers span the gap between intermeshed fins, allowing heat transfer by conduction through the fibers. The fibers are attached to the metal surfaces as velvet-like coats in the manner of the carbon fiber brush heat exchangers described in the preceding article. The fiber brushes provide both mechanical compliance and thermal contact, thereby ensuring low contact thermal resistance. A certain amount of force is required to intermesh the fins due to sliding friction of the brush s fiber tips against the fins. This force increases linearly with penetration distance, reaching ~1 psi (~6.9 kPa) for full 2-in. (5.1 cm) penetration for the conventional radiant fin interface. Removal forces can be greater due to fiber buckling upon reversing the sliding direction. This buckling force can be greatly reduced by biasing the fibers at an angle perpendicularly to the sliding direction. Means of containing potentially harmful carbon fiber debris, which is electrically conductive, have been developed. Small prototype brush/fin thermal interfaces have been tested and found to exhibit temperature drops about onesixth of that of conventional meshing-fin thermal interface, when fabricated as a retrofit. In this case, conduction through the long, thin metal fins themselves becomes a thermal bottleneck. Further improvement could be made by prescribing aluminum fins to be shorter and thicker than those of the conventional meshing-fin thermal interfaces; the choice of height and thickness would be optimized to obtain greater overall thermal conductance, lower weight, and lower cost.

Knowles, Timothy R.↗