SEARCH · Search NASA

Results for “Rotorcrafts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1982

A comparison of wind tunnels suitable for rotorcraft noise studies

Many good small scale facilities are available for rotorcraft noise research. Ames 40 x 80/80 x 120 probably is a good large scale facility for acoustic research of large or small rotorcraft, but the acoustic quality of the modified facility was not yet measured. DNW is probably the best aeroacoustic facility, but may be expensive. Other parameters to consider besides background noise are turbulent level and scale, restructed measurement field, local reflections, and speed range. Advanced measurement techniques improve data quality from any facility.

Soderman, P. T.↗

NASA NTRS1982

Rotorcraft noise prediction

The purpose of this presentation is to give a general strategy for rotorcraft noise prediction. This strategy is expressed through a modular software system design rather than theoretical analysis of the aerocoustic phenomena. The crucial design choices in a software system design are the module interface definitions. An interface is the data that are passed from one module to another. A module takes data from one (input) interface and transforms it, through a prediction method, to another (output) interface. In system design, the method is less important than the interface. The two types of methods available may be braodly classified as empirical or analytical, although no method is purely one or the other. These two general approaches will be compared as they apply to rotorcraft noise prediction.

Zorumski, W. E.↗

NASA NTRS1983

Development and flight test of an X-band precision approach concept for remote-area rotorcraft operations

A novel airborne radar-based precision approach concept was developed and flight tested as a part of NASA's Rotorcraft All-Weather Operations Research Program. A demonstration, transponder-based beacon landing system (BLS), incorporating state-of-the-art X-band radar technology and digital processing techniques, was built and flight tested to demonstrate the concept feasibility. The BLS airborne hardware consists of an add-on microprocessor, installed in conjunction with the aircraft weather/mapping radar, which analyzes the radar beacon receiver returns and determines range, localizer deviation, and glide slope deviation. The ground station is an inexpensive, portable unit which can be quickly deployed at a landing site. Results from the flight test program show that the BLS concept has a significant potential for providing rotorcraft with low-cost, precision, instrument approach capability in remote areas. Previously announced in STAR as N84-10041

Clary, G. R.↗

NASA NTRS1984

Development of large rotorcraft transmissions

The U.S. Army Heavy Lift Helicopter (HLH) represents a large rotorcraft which was developed by an American aerospace company. In the early 1970's with the HLH Advanced Technology Components (ATC) program, the development of large rotorcraft transmission and drive systems was started. Failures in the spiral bevel gearing were experienced in tests because the employed method of analysis had not considered the effect of rim bending. Consequently, new gears with strengthened rims were designed and fabricated. For a more accurate prediction of the load capacity of the gears, an extensive Finite Element Method (FEM) system was developed. The U.S. Army's XCH-62 HLH aft rotor transmission was finally successfully tested at full design torque and speed. A description of the test program is provided, and the analytical program is discussed. The analytical phase includes the development of a preprocessing program which aids in the review of calculated FEM stresses.

Samanich, N. E.↗

NASA NTRS1984

A practical approach to rotorcraft systems identification

A standard for rotorcraft system identification is proposed to facilitate the exchange of data and technology within the industry. This integrated approach utilizes simulations to validate methodology and flight data to validate simulations. A new technique allowing results obtained from separate maneuvers to be systematically combined is also presented and shown to be a fundamental tool in providing a practical approach to rotorcraft identification. The proposed methodology is evaluated using data generated by nonlinear blade-element simulation of the Rotor Systems Research Aircraft.

Du Val, R. W.↗

NASA NTRS1985

Effects of side-stick controllers on rotorcraft handling qualities for terrain flight

Pertinent fixed and rotary-wing feasibility studies and handling-qualities research programs are reviewed and the effects of certain controller characteristics on handling qualities for specific rotorcraft flight tasks are summarized. The effects of the controller force-deflection relationship and the number of controlled axes that are integrated in a single controller are examined. Simulation studies were conducted which provide a significant part of the available handling qualities data. The studies demonstrate the feasibility of using a single, properly designed, limited-displacement, multiaxis controller for certain relatively routine flight tasks in a two-crew rotorcraft with nominal levels of stability and control augmentation with a high degree of reliability are incorporated, separated three or two-axis controller configurations are required for acceptable handling qualities.

Aiken, E. W.↗

NASA NTRS1984

Rotorcraft simulation at Ames

Attention is given to rotorcraft simulation experience at NASA's Ames research facility, which has involved complex mathematical modeling, high computational capability requirements, and strong influences from pilot motion and visual cues. A development history and performance assessment is presented for the rotorcraft simulation hardware, together with projections of near term development improvements of capabilities. Greater demand is anticipated for the simulation of all-digital helicopter flight control systems.

Alderete, T. S.↗

NASA NTRS1985

Rotorcraft Dynamics 1984

In the conference proceedings are 24 presented papers, their discussions, and material given in two panels. The presented papers address the general areas of the dynamics of rotorcraft or helicopters. Specific topics include the stability of rotors in hover and forward flight, the stability of coupled rotor-fuselage systems in hover, the loads on a rotor in forward flight including new developments in rotor loads calculations, and the calculation of rotorcraft vibration and means for its control or suppression. Material in the first panel deals with the successful application of dynamics technology to engineering development of flight vehicles. Material in the second panel is concerned with large data bases in the area of rotorocraft dynamics and how they are developed, managed, and used.

Source record↗

NASA NTRS1985

Effects of side-stick controllers on rotorcraft handling qualities for terrain flight

Aiken, E. W.↗

NASA NTRS1986

Outdoor test stand performance of a convertible engine with variable inlet guide vanes for advanced rotorcraft propulsion

A variable inlet guide van (VIGV) type convertible engine that could be used to power future high-speed rotorcraft was tested on an outdoor stand. The engine ran stably and smoothly in the turbofan, turboshaft, and dual (combined fan and shaft) power modes. In the turbofan mode with the VIGV open fuel consumption was comparable to that of a conventional turbofan engine. In the turboshaft mode with the VIGV closed fuel consumption was higher than that of present turboshaft engines because power was wasted in churning fan-tip airflow. In dynamic performance tests with a specially built digital engine control and using a waterbrake dynamometer for shaft load, the engine responded effectively to large steps in thrust command and shaft torque. Previous mission analyses of a conceptual X-wing rotorcraft capable of 400-knot cruise speed were revised to account for more fan-tip churning power loss than was originally estimated. The new calculations confirm that using convertible engines rather than separate lift and cruise engines would result in a smaller, lighter craft with lower fuel use and direct operating cost.

Mcardle, Jack G.↗

NASA NTRS1987

Digital control of highly augmented combat rotorcraft

Proposed concepts for the next generation of combat helicopters are to be embodied in a complex, highly maneuverable, multiroled vehicle with avionics systems. Single pilot and nap-of-the-Earth operations require handling qualities which minimize the involvement of the pilot in basic stabilization tasks. To meet these requirements will demand a full authority, high-gain, multimode, multiply-redundant, digital flight-control system. The gap between these requirements and current low-authority, low-bandwidth operational rotorcraft flight-control technology is considerable. This research aims at smoothing the transition between current technology and advanced concept requirements. The state of the art of high-bandwidth digital flight-control systems are reviewed; areas of specific concern for flight-control systems of modern combat are exposed; and the important concepts are illustrated in design and analysis of high-gain, digital systems with a detailed case study involving a current rotorcraft system. Approximate and exact methods are explained and illustrated for treating the important concerns which are unique to digital systems.

Tischler, Mark B.↗

NASA NTRS1987

Application of GRASP (General Rotorcraft Aeromechanical Stability Program) to nonlinear analysis of a cantilever beam

The General Rotorcraft Aeromechanical Stability Program (GRASP) was developed to analyse the steady-state and linearized dynamic behavior of rotorcraft in hovering and axial flight conditions. Because of the nature of problems GRASP was created to solve, the geometrically nonlinear behavior of beams is one area in which the program must perform well in order to be of any value. Numerical results obtained from GRASP are compared to both static and dynamic experimental data obtained for a cantilever beam undergoing large displacements and rotations caused by deformations. The correlation is excellent in all cases.

Hinnant, Howard E.↗

NASA NTRS1988

NASA/Army Rotorcraft Technology. Volume 1: Aerodynamics, and Dynamics and Aeroelasticity

The Conference Proceedings is a compilation of over 30 technical papers presented at this milestone event which reported on the advances in rotorcraft technical knowledge resulting from NASA, Army, and industry rotorcraft research programs over the last 5 to 10 years. The Conference brought together over 230 government, industry, and allied nation conferees to exchange technical information and hear invited technical papers by prominent NASA, Army, and industry researchers covering technology topics which included: aerodynamics, dynamics and elasticity, propulsion and drive systems, flight dynamics and control, acoustics, systems integration, and research aircraft.

Source record↗

NASA NTRS1988

NASA's rotorcraft icing research program

The objective of the NASA aircraft icing research program is to develop and make available icing technology to support the needs and requirements of industry for all weather aircraft designs. While a majority of the technology being developed is viewed to be generic (i.e., appropriate to all vehicle classes), vehicle specific emphasis is being placed on the helicopter due to its unique icing problems. In particular, some of the considerations for rotorcraft icing are indicated. The NASA icing research program emphasizes technology development in two key areas: ice protection concepts and icing simulation (analytical and experimental). The NASA research efforts related to rotorcraft icing in these two technology areas will be reviewed.

Shaw, Robert J.↗

NASA NTRS1988

Rotorcraft flight-propulsion control integration

The NASA Ames and Lewis Research Centers, in conjunction with the Army Research and Technology Laboratories have initiated and completed, in part, a joint research program focused on improving the performance, maneuverability, and operating characteristics of rotorcraft by integrating the flight and propulsion controls. The background of the program, its supporting programs, its goals and objectives, and an approach to accomplish them are discussed. Results of the modern control governor design of the T700 and the Rotorcraft Integrated Flight-Propulsion Control Study, which were key elements of the program, are also presented.

Mihaloew, James R.↗

NASA NTRS1988

Status of NASA/Army rotorcraft research and development piloted flight simulation

The status of the major NASA/Army capabilities in piloted rotorcraft flight simulation is reviewed. The requirements for research and development piloted simulation are addressed as well as the capabilities and technologies that are currently available or are being developed by NASA and the Army at Ames. The application of revolutionary advances (in visual scene, electronic cockpits, motion, and modelling of interactive mission environments and/or vehicle systems) to the NASA/Army facilities are also addressed. Particular attention is devoted to the major advances made in integrating these individual capabilities into fully integrated simulation environment that were or are being applied to new rotorcraft mission requirements. The specific simulators discussed are the Vertical Motion Simulator and the Crew Station Research and Development Facility.

Condon, Gregory W.↗

NASA NTRS1988

Rotorcraft flight-propulsion control integration: An eclectic design concept

The NASA Ames and Lewis Research Centers, in conjunction with the Army Research and Technology Laboratories, have initiated and partially completed a joint research program focused on improving the performance, maneuverability, and operating characteristics of rotorcraft by integrating the flight and propulsion controls. The background of the program, its supporting programs, its goals and objectives, and an approach to accomplish them are discussed. Results of the modern control governor design of the General Electric T700 engine and the Rotorcraft Integrated Flight-Propulsion Control Study, which were key elements of the program, are also presented.

Mihaloew, James R.↗

NASA NTRS1988

Some rotorcraft applications of computational fluid dynamics

The growing application of computational aerodynamics to nonlinear rotorcraft problems is outlined, with particular emphasis on the development of new methods based on the Euler and thin-layer Navier-Stokes equations. Rotor airfoil characteristics can now be calculated accurately over a wide range of transonic flow conditions. However, unsteady 3-D viscous codes remain in the research stage, and a numerical simulation of the complete flow field about a helicopter in forward flight is not now feasible. Nevertheless, impressive progress is being made in preparation for future supercomputers that will enable meaningful calculations to be made for arbitrary rotorcraft configurations.

Mccroskey, W. J.↗