Search NASA⌕ Search

SEARCH · Search NASA

Results for “SEDIMENTATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Foam Delivery of Amendments for Vadose Zone Remediation – Propagation Performance in Unsaturated Sediments

Foam delivery of remedial amendments is potentially useful for vadose zone remediation because aqueous amendments are delivered while maintaining a low water content. The transport behavior of foam in the vadose zone is not well studied. Bench top scale column tests were conducted to investigate the foam transport, foaming gas and liquid propagation, pressure build up and distribution, influence of foam quality and sediment permeability on foam injection pressure, and liquid up-taking and distribution in sediments during foam flow in unsaturated sediments. Results indicated that under the unsaturated conditions, foaming gas front traveled much faster than the foam front where bubbles rupture was significant. A liquid front was formed ahead of the foam flow front. The accumulated liquid in this front was mainly composed of the water injected with foam. The foam injection pressure was mostly attributed to the resistance to foam flow from the sediment, but not to the movement of the water ahead of the foam front. Foam had a high effective viscosity compare to water. A near linear pressure distribution within the foam-occupied column section was observed. At fixed injection rate, higher foam quality resulted lower injection pressure. Higher permeability sediments did not necessarily have a lower foam injection pressure, as other factors such as the foam injection rate, foam bubble diameter, and sediment pore size also influenced the pressure. In the foam flushed region, the liquid uptake and the water content distribution in sediment was barely affected by the initial water content and the foam injection rate. The implications of these findings in field remediation application were discussed.

54 ENVIRONMENTAL SCIENCES↗

New Technique for Speciation of Uranium in Sediments Following Acetate-Stimulated Bioremediation

Acetate-stimulated bioremediation is a promising new technique for sequestering toxic uranium contamination from groundwater. The speciation of uranium in sediments after such bioremediation attempts remains unknown as a result of low uranium concentration, and is important to analyzing the stability of sequestered uranium. A new technique was developed for investigating the oxidation state and local molecular structure of uranium from field site sediments using X-Ray Absorption Spectroscopy (XAS), and was implemented at the site of a former uranium mill in Rifle, CO. Glass columns filled with bioactive Rifle sediments were deployed in wells in the contaminated Rifle aquifer and amended with a hexavalent uranium (U(VI)) stock solution to increase uranium concentration while maintaining field conditions. This sediment was harvested and XAS was utilized to analyze the oxidation state and local molecular structure of the uranium in sediment samples. Extended X-Ray Absorption Fine Structure (EXAFS) data was collected and compared to known uranium spectra to determine the local molecular structure of the uranium in the sediment. Fitting was used to determine that the field site sediments did not contain uraninite (UO{sub 2}), indicating that models based on bioreduction using pure bacterial cultures are not accurate for bioremediation in the field. Stability tests on the monomeric tetravalent uranium (U(IV)) produced by bioremediation are needed in order to assess the efficacy of acetate-stimulation bioremediation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Variability of K d Values in Cementitious Materials and Sediments

Measured distribution coefficients (K d values) for environmental contaminants provide input data for performance assessments (PA) that evaluate physical and chemical phenomena for release of radionuclides from wasteforms, degradation of engineered components and subsequent transport of radionuclides through environmental media. Research efforts at SRNL to study the effects of formulation and curing variability on the physiochemical properties of the saltstone wasteform produced at the Saltstone Disposal Facility (SDF) are ongoing and provide information for the PA and Saltstone Operations. Furthermore, the range and distribution of plutonium K d values in soils is not known. Knowledge of these parameters is needed to provide guidance for stochastic modeling in the PA. Under the current SRS liquid waste processing system, supernate from F & H Tank Farm tanks is processed to remove actinides and fission products, resulting in a low-curie Decontaminated Salt Solution (DSS). At the Saltstone Production Facility (SPF), DSS is mixed with premix, comprised of blast furnace slag (BFS), Class F fly ash (FA), and portland cement (OPC) to form a grout mixture. The fresh grout is subsequently placed in SDF vaults where it cures through hydration reactions to produce saltstone, a hardened monolithic waste form. Variation in saltstone composition and cure conditions of grout can affect the saltstone's physiochemical properties. Variations in properties may originate from variables in DSS, premix, and water to premix ratio, grout mixing, placing, and curing conditions including time and temperature (Harbour et al. 2007; Harbour et al. 2009). There are no previous studies reported in the literature regarding the range and distribution of K d values in cementitious materials. Presently, the Savannah River Site (SRS) estimate ranges and distributions of K d values based on measurements of K d values made in sandy SRS sediments (Kaplan 2010). The actual cementitious material K d values and solubility values differ from the sandy sediments. The K d value range and distribution currently used in the PA are estimated to range between 0.25*K d and 1.75*K d , where the minimum and maximum values of the ranges reflect the 95% confidence level for the mean K d value (Kaplan 2010). The objective of the research with cementitious materials was to measure the range and distribution of a monovalent (Cs) and I - (anion), divalent (Sr), and trivalent (Eu) ions for a variety of laboratory-prepared saltstone surrogate samples to establish a K d range other than that which is presently used in the PA. It has been observed in laboratory samples that cure temperature profiles can affect properties such as heat of hydration, permeability, porosity, compressive strength, and set time (Harbour et al. 2009). The intent was to identify a range and distribution that could be used by stochastic modelers for the PA. Furthermore, the intent was to replace the arbitrarily selected distributions based on geological sandy sediments and to base it on actual cementitious materials. The scope of this study did not include understanding saltstone sorption mechanisms responsible for increasing or decreasing sorption. Similar to the work with cementitious materials, the purpose of the Pu sediment K d dataset was not to attempt to understand through statistics how to better understand Pu sorption to sediments or to lower Pu K d variance. The sediment Pu K d data is included in this study because it is a key risk driver for the PAs on the SRS, and there is presently no direct studies of Pu variability in SRS soils. Instead the distribution of Pu sediment K d values was assumed to be similar to other cations, as presented by Kaplan (2010).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

129 I, 99 Tc, And U Distribution Coefficients of Subsurface Sediments Collected from the Proposed Site of the Environmental Management Disposal Facility

Performance Assessment calculations were completed in 2020 to evaluate the Environmental Management Disposal Facility (EMDF), a proposed new low-level radioactive waste (LLW) disposal facility on the U.S. Department of Energy’s Oak Ridge Reservation (ORR). Among the large number of input parameters needed for such calculations, are distribution coefficients (K d values; radionuclide concentration solid:liquid ratio) that provide a measure of the tendency of radionuclides to bind to sediments. The objective of this study was to measure K d values of three radionuclides that may pose a disproportionately large amount of risk, U, 129 I and 99 Tc. The average I K d value for the 14 geological materials recovered from the proposed EMDF site was 37.8 mL/g and ranged from -1.8 to 140.9 mL/g. These values were consistent, but somewhat larger than previous measurements made with ORR sediments and were about an order of magnitude greater than those used in previous EMDF PA calculations. The median Tc K d value was 365.7 mL/g, much greater than previously reported using ORR geological materials. Five of the 14 tested geological materials sorbed large quantities of Tc, suggesting that the weakly sorbing Tc(VII) species had been reduced to the sparingly soluble Tc(IV) species. The five strongly sorbing sediments had apparent Tc solubility values of approximately <10 -8 mol/L. The median U K d value was 5,726 mL/g. All of the tested geological materials had large K d values, ranging from 625 to >10,208 mL/g. Among the sediment samples that exhibited strong U binding, the apparent solubility value was approximately <10 -9 mol/L. Based on sediment properties and general ORR geological considerations, it was proposed that much of the I and Tc retention could be attributed to the site materials exhibiting low pH (average pH = 4.94), low redox status, and/or the elevated levels of iron oxides, manganese oxides, and natural organic matter. Similarly, the extremely high U binding measured in these sediments may also be attributed to the low conditions of carbonates, which can complex and therefore solubilize uranyl in these tests due to the low pH, and also the relatively high concentrations of iron and organic coatings on these samples. An implication of this study is that the areas of the EMDF subsurface environment may have natural properties for attenuating I, Tc, and U movement, and potentially other radionuclides, thereby possibly reducing risk posed by burial of LLW at this site. This document is a revision of SRNL-STI-2021-00404, Revision 0 that includes new data describing U K d values and new I and Tc K d values for four Nolichucky sediments. These new results were integrated into the data presented in the original document.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Cryptic Methane-Cycling by Methanogens During Multi-Year Incubation of Estuarine Sediment

As marine sediments are buried, microbial communities transition from sulfate-reduction to methane-production after sulfate is depleted. When this biogenic methane diffuses into the overlying sulfate-rich sediments, it forms a sulfate-methane transition zone (SMTZ) because sulfate reducers deplete hydrogen concentrations and make hydrogenotrophic methanogenesis exergonic in the reverse direction, a process called the anaerobic oxidation of methane (AOM). Microbial participation in these processes is often inferred from geochemistry, genes, and gene expression changes with sediment depth, using sedimentation rates to convert depth to time. Less is known about how natural sediments transition through these geochemical states transition in real-time. We examined 16S rRNA gene amplicon libraries and metatranscriptomes in microcosms of anoxic sediment from the White Oak River estuary, NC, with three destructively sampled replicates with methane added (586-day incubations) and three re-sampled un-amended replicates (895-day incubations). Sulfate dropped to a low value (∼0.3 mM) on similar days for both experiments (312 and 320 days, respectively), followed by a peak in hydrogen, intermittent increases in methane-cycling archaea starting on days 375 and 362 (mostly Methanolinea spp. and Methanosaeta spp., and Methanococcoides sp. ANME-3), and a methane peak 1 month later. However, methane δ 13 C values only show net methanogenesis 6 months after methane-cycling archaea increase and 4 months after the methane peak, when sulfate is consistently below 0.1 mM and hydrogen increases to a stable 0.61 ± 0.13 nM (days 553–586, n = 9). Sulfate-reducing bacteria (mostly Desulfatiglans spp. and Desulfosarcina sp. SEEP-SRB1) increase in relative abundance only during this period of net methane production, suggesting syntrophy with methanogens in the absence of sulfate. The transition from sulfate reduction to methane production in marine sediments occurs through a prolonged period of methane-cycling by methanogens at low sulfate concentrations, and steady growth of sulfate reducers along with methanogens after sulfate is depleted.

59 BASIC BIOLOGICAL SCIENCES↗

Long-term warming modulates diversity, vertical structuring of microbial communities, and sulfate reduction in coastal Baltic Sea sediments

Coastal waters such as those found in the Baltic Sea already suffer from anthropogenic related problems including increased algal blooming and hypoxia while ongoing and future climate change will likely worsen these effects. Microbial communities in sediments play a crucial role in the marine energy- and nutrient cycling, and how they are affected by climate change and shape the environment in the future is of great interest. The aims of this study were to investigate potential effects of prolonged warming on microbial community composition and nutrient cycling including sulfate reduction in surface (∼0.5 cm) to deeper sediments (∼ 24 cm). To investigate this, 16S rRNA gene amplicon sequencing was performed, and sulfate concentrations were measured and compared between sediments in a heated bay (which has been used as a cooling water outlet from a nearby nuclear power plant for approximately 50 years) and a nearby but unaffected control bay. The results showed variation in overall microbial diversity according to sediment depth and higher sulfate flux in the heated bay compared to the control bay. A difference in vertical community structure reflected increased relative abundances of sulfur oxidizing- and sulfate reducing bacteria along with a higher proportion of archaea, such as Bathyarchaeota, in the heated compared to the control bay. This was particularly evident closer to the sediment surface, indicating a compression of geochemical zones in the heated bay. These results corroborate findings in previous studies and additionally point to an amplified effect of prolonged warming deeper in the sediment, which could result in elevated concentrations of toxic compounds and greenhouse gases closer to the sediment surface.

16S rRNA gene amplicon↗

Remediation of Uranium Impacted Sediments in a Watercourse - 12486

In 2009, remediation was initiated for a non-operational fuel cycle facility previously used for government contract work. Between 2009 and the spring of 2011, remediation efforts were focused on demolition of contaminated buildings and removal of contaminated soil. In the late spring of 2011, the last phase of remediation commenced involving the removal of contaminated sediments from portions of a 1,200 meter long gaining stream. Planning and preparation for remediation of the stream began in 2009 with submittal of permit applications to undertake construction activities in a wetland area. The permitting process was lengthy and involved securing permits from multiple agencies. However, early and frequent communication with stakeholders played an integral role in efficiently obtaining the permit approvals. Frequent communication with stakeholders throughout the planning and remediation process also proved to be a key factor in timely completion of the project. The remediation of the stream involved the use of temporary bladder berms to divert surface water flow, water diversion piping, a sediment vacuum removal system, excavation of sediments using small front-end loaders, sediment dewatering, and waste packaging, transportation and disposal. Many safeguards were employed to protect several species of concern in the work area, water management during project activities, challenges encountered during the project, methods of Final Status Survey, and stream restoration. The planning and permitting effort for the Site Brook remediation began in May 2009 and permits were approved and in place by February 2011. The remediation and restoration of the Site Brook began in April 2011 and was completed in November 2011. The remediation of the Site Brook involved the use of temporary bladder berms to divert surface water flow, water diversion piping, a sediment vacuum removal system, excavation of sediments using small front-end loaders, sediment dewatering, and waste packaging, transportation, disposal, FSS, and restoration. Early and frequent communications with stakeholders proved to be a key factor in timely completion of the project. Challenges encountered during the remediation effort were overcome by proper planning and having preparedness procedures in place prior to executing the work. With the remediation and restoration successfully completed, the only remaining task is to monitor/maintain the restoration for 10 years. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Synergetic Interactions between Uranium, Humic Acid, Silica Colloids and SRS Sediments at Variable pH - 16524

The Savannah River Site (SRS) was constructed during the 1950's and became one of the major producers of plutonium for the United States during the Cold War. During its production life, the F/H Area Seepage Basins received approximately 1.8 billion gallons of acidic waste containing radionuclides and dissolved heavy metals. This led to the creation of a highly contaminated groundwater plume with uranium (VI) as a key contaminant of concern within the plume. Now, as a designated hazardous waste management facility, the main activities taking place at the site are nuclear storage and remediation of contaminated soil and groundwater from radionuclides. Humic substances (HS) are major components of soil organic matter having the ability to influence migration behavior and fate of heavy metals and are being investigated for potential use in environmental remediation at SRS. Essentially, HS are polyfunctional organic macromolecules formed by the chemo-microbiological decomposition of biomass or dead organic matter. HS are able to interact with both metal ions and organic compounds based on solubility. Humic acid (HA) represents the fraction of HS soluble at pH greater than 3.5. HA carries a large number of functional groups, provides an important function in ion exchange and is a metal complexing ligand with a high complexation capacity. Silica is the term applied to solid forms with the stoichiometric composition of SiO{sub 2}. The colloidal silica used in this work is amorphous and non-porous in suspension; silica's net surface charge for pH values higher than 3 is negative, due to the isoelectric point being 1.5 - 2.5. Humic acid has been previously used in remediation techniques and silica is found naturally in the soil. This investigation studied the synergistic interactions between four key components: U(VI), humic acid (HA), colloidal silica and SRS sediment under varying pH conditions ranging from 3 to 8. Multi-component batch systems were constructed to effectively analyze the removal of U(VI). The batches were pH adjusted, left to equilibrate for a minimum of 48 hours on a shaker, and then centrifuged. A set of samples, filtered to remove any colloids in suspension, and a set of unfiltered samples were analyzed. For the samples at acidic pH, the uranyl cation is the dominant species; with increasing pH, the mononuclear and polynuclear hydrolyzed uranyl ions become dominant based on speciation modeling. In filtered samples, uranium removal is highest at low pH with the negatively charged moieties of HA readily binding to the uranyl cation. Percent removal of U(VI) steadily decreased with an increase in pH and then remained comparable at a neutral/alkaline pH with the change in uranyl speciation. The percentage of colloidal silica removal was observed to be approximately 80% for both sediment- and non-sediment-bearing samples. As the pH increased, the silica removal in the non-sediment set showed a slight decrease and was in the range of 70% - 75%. Uranium removal in the unfiltered samples showed similar trends as compared to the filtered samples; however, the removal of uranium in the unfiltered samples was slightly lower compared to the filtered samples. Colloidal silica removal in non-sediment-bearing batches showed a decline with increasing pH, from 90% to 50%; conversely, the silica removal remained constant for the sediment-bearing batches at approximately 60%. Colloidal silica does not seem to have a significant effect on the removal of U(VI) before filtration due to U(VI) bound to colloidal silica remaining in suspension. The presence of humic acid, silica colloids, and SRS sediment was shown to synergistically effect the removal of U(VI). (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Eddy‐driven sediment transport in the A rgentine B asin: Is the height of the Z apiola R ise hydrodynamically controlled?

Abstract In this study, we address the question whether eddy‐driven transports in the Argentine Basin can be held responsible for enhanced sediment accumulation over the Zapiola Rise, hence accounting for the existence and growth of this sediment drift. To address this question, we perform a 6 year simulation with a strongly eddying ocean model. We release two passive tracers, with settling velocities that are consistent with silt and clay size particles. Our experiments show contrasting behavior between the silt fraction and the lighter clay. Due to its larger settling velocity, the silt fraction reaches a quasisteady state within a few years, with abyssal sedimentation rates that match net input. In contrast, clay settles only slowly, and its distribution is heavily stratified, being transported mainly along isopycnals. Yet, both size classes display a significant and persistent concentration minimum over the Zapiola Rise. We show that the Zapiola Anticyclone, a strong eddy‐driven vortex that circulates around the Zapiola Rise, is a barrier to sediment transport, and hence prevents significant accumulation of sediments on the Rise. We conclude that sediment transport by the turbulent circulation in the Argentine Basin alone cannot account for the preferred sediment accumulation over the Rise. We speculate that resuspension is a critical process in the formation and maintenance of the Zapiola Rise.

58 GEOSCIENCES↗

Laboratory Strategies for Hydrate Formation in Fine‐Grained Sediments

Abstract Fine‐grained sediments limit hydrate nucleation, shift the phase boundary, and hinder gas supply. Laboratory experiments in this study explore different strategies to overcome these challenges, including the use of a more soluble guest molecule rather than methane, grain‐scale gas‐storage within porous diatoms, ice‐to‐hydrate transformation to grow lenses at predefined locations, forced gas injection into water saturated sediments, and long‐term guest molecule transport. Tomographic images and thermal and pressure data provide rich information on hydrate formation and morphology. Results show that hydrate formation is inherently displacive in fine‐grained sediments; lenses are thicker and closer to each other in compressible, high specific surface area sediments subjected to low effective stress. Temperature and pressure trajectories follow a shifted phase boundary that is consistent with capillary effects. Exo‐pore growth results in freshly formed hydrate with a striped and porous structure; this open structure becomes an effective pathway for gas transport to the growing hydrate front. Ice‐to‐hydrate transformation goes through a liquid stage at premelt temperatures; then, capillarity and cryogenic suction compete, and some water becomes imbibed into the sediment faster than hydrate reformation. The geometry of hydrate lenses and the internal hydrate structure continue evolving long after the exothermal response to hydrate formation has completely decayed. Multiple time‐dependent processes occur during hydrate formation, including gas, water and heat transport, sediment compressibility, reaction rate, and the stochastic nucleation process. Hydrate formation strategies conceived for this study highlight the inherent difficulties in emulating hydrate formation in fine‐grained sediments within the relatively short time scale available for laboratory experiments.

Lei, L.↗

Phosphorus and cover crop management practices affect phosphorus speciation in soils and eroded sediments

Abstract Agricultural runoff often contains P in dissolved and sediment‐bound forms, decreasing surface water quality. No‐till and cover cropping conservation practices have been recommended for reducing erosion and nutrient loss from cropping systems. The overall aims of this study were to characterize and evaluate the effects of fertilizer (placement and source) and cover crop management on P speciation in surface runoff sediments and source soil. In 2014, a field‐scale experiment was established in a no‐till, corn (Zea maysL.)–soybean (Glycine maxL.) cropping system with two cover crop treatments (with and without a winter crop; winter wheat [Triticum aestivumL.], rapeseed [Brassica napusL.], hairy vetch [Vicia villosaRoth], winter triticale [×Triticosecale Wittm.], and cereal rye [Secale cerealeL.]) and three P fertilizer management treatments (no P, fall broadcast diammonium phosphate, and spring subsurface injected ammonium polyphosphate). Phosphorus fractionation in the source soil collected in the fall of 2019 and sediment samples collected throughout 2020 were analyzed using a modified sequential P extraction method to evaluate the cumulative effects of imposing the treatment factors over 5 years. The direct P speciation was done using X‐ray absorption near edge structure spectroscopy. The indirect P speciation (fractionation) results showed that the management practices affected the exchangeable, organic matter‐associated, and Fe‐bound P fractions in sediments and the exchangeable and residual fractions in source soil. Direct P speciation results showed a depletion of Fe‐associated P in soil and sediment from cover crop treatment, suggesting that Fe‐associated P species were affected by cover crops. Changes in soil and runoff sediment P speciation would change the proportions and forms of soluble and particulate P in runoff sediments and may influence P bioavailability in aquatic ecosystems. Developing P fertilizer and cropping system management options with an understanding of soil P transformations helps maintain environmental sustainability.

Environmental Sciences & Ecology↗

Bench-scale electrokinetic remediation for cesium-contaminated sediment at the Hanford Site, USA

Electrokinetic (EK) remediation has been applied to extract various contaminants such as radionuclides, heavy metals, and organic compounds from contaminated sediment and soil using electric currents. We conducted a laboratory experiment to investigate the efficiency of EK remediation method for Hanford sediment (76% sand and 24% silt-clay) after artificial contamination with nonradioactive 133Cs (0.01 M CsNO3) as a surrogate for radioactive 137Cs. The initial 133Cs concentration in the bulk sediment was 668 mg kg-1, with a higher 133Cs concentration for the silt-clay fraction (867 mg kg-1) than for the sand fraction (83 mg kg-1). A significant removal of cationic 133Cs from the sediment occurred from the cathode side (-), whereas the removal was negligible from the anode side (+) during the EK remediation process for 68 days. Based on microwave-assisted total digestion, 312 mg kg-1 of 133Cs was removed from the bulk sediment, which corresponds to the removal efficiency of 47%. The EK method was significantly more efficient for the silt-clay fraction than for the sand fraction. X-ray diffraction (XRD) and scanning electron microscopy-electron dispersive spectroscopy (SEM-EDS) analyses indicate that change in major crystalline mineral phases was insignificant during the EK remediation and the removal of 133Cs from the Hanford sediment by the EK method is attributed mainly to cation exchange with K in clay minerals. The experimental results suggest that the EK method can effectively remove radioactive Cs from the surface or subsurface sediment contaminated by radioactive materials in the Hanford Site, Washington, USA.

Cation exchange↗

Microbially mediated iron redox cycling of subsurface sediments from Hanford Site, Washington State, USA

Iron-bearing clay minerals are predominant in soils and sediments, and they undergo oxidation-reduction cycles as a result of natural processes such as wetting/drying cycles and plant root respiration. However, the kinetics and mechanisms of multiple redox cycles of iron in clay-rich sediments and consequences of such cycling on sediment properties are poorly understood. The objective of this study was to understand how multiple redox cycles of Fe in clay-rich sediment affect the rate and extent of Fe bioreduction and the physicochemical properties of the sediment. A natural sediment sample containing Fe-bearing montmorillonite from Hanford, Washington, USA was size-fractionated [2.0 to 0.5 μm (Hanford-C) and 0.5 to 0.02 μm (Hanford-F)] and redox-cycled for four times. Bioreduction was achieved utilizing Geobacter sulfurreducens and re-oxidization was performed with sparged air. Time-course change of total Fe (II) was monitored to measure the rate and extent of Fe (III) bioreduction. Redox-cycled sediments were characterized to determine the physicochemical changes. Both the initial rate and extent of bioreduction fluctuated across the four redox cycles, but they ultimately decreased from 5.3 μmol g -1 h -1 and 22.9% to nearly zero by the fourth cycle. These fluctuation patterns were likely due to a combined effect of reductive dissolution of small/poorly crystalline clay particles (by 3–5%) and clay mineral structural changes, as evidenced by redox induced changes of aqueous chemistry, surface area, cation exchange capacity, mineralogy, and Mössbauer parameters. Once these small/poorly crystalline clay particles were dissolved, structural Fe in residual larger and more crystalline clay particles was largely reversible across additional redox cycles, as revealed by Mössbauer spectroscopy through the first three cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Sulfur, iron-, and calcium cycling associated with natural electric currents running through marine sediment

Anaerobic oxidation of organic matter in marine sediment is traditionally considered to be coupled to oxygen reduction via a cascade of redox processes and transport of intermittent electron donors and acceptors. Long distance electron transmission (LDET) has recently been shown to shortcut this cascade and directly couple oxygen reduction at the surface to sulphide oxidation in deeper anoxic layers. Here we show that spatial separation of oxidation and reduction processes in marine sediment causes non-conventional sulphur, iron, and calcium cycling. Reduced sediment was incubated with overlying oxic water and the vertical distribution of solutes and solids analysed 45 days later. As much as 44% of sediment oxygen consumption proved to be mediated by LDET, and electrogenic oxidation of sulphide to sulphate resulted in significant dissolution of iron sulphides and calcium carbonates in the anoxic layers of the sediment. Most of the mobilised iron diffused to the oxic zone where it formed oxidised iron minerals. Calcium precipitated out in the oxic zone as magnesium-calcite. In marine sediment, LDET thus generates unique chemical conditions whereby key minerals are mobilised and relocated, probably along with trace elements and nutrients. We suggest that LDET flourishes in marine sediments after transient oxygen depletion, leaving distinct signatures of such events in the geological record.

54 ENVIRONMENTAL SCIENCES↗

Mineralogical transformations in polymetallic nodules and the change of Ni, Cu and Co crystal-chemistry upon burial in sediments

Polymetallic nodules from the Clarion and Clipperton Zone of the equatorial Pacific Ocean were studied using X-ray diffraction, X-ray absorption, Fourier-transformed infrared spectroscopy and transmission electron microscopy. Here, this study includes nodules found at the sediment surface as well as subsurface (14–16 cm sediment depth) and deeply buried (530–985 cm sediment depth) nodules. The surface and subsurface nodules are currently under oxic conditions whereas the deeply buried nodules are under suboxic conditions. Surface nodules consist mainly of turbostratic phyllomanganates (7 Å and 10 Å vernadite and Fe-vernadite); todorokite is a minor phase, if present at all. In contrast, subsurface and especially deeply buried nodules predominantly consist of todorokite, which increases in abundance with depth in the sediment. Thus, upon burial of nodules within the shallow sediment, phyllomanganates transform to todorokite, probably through the combined action of time and change in the ambient chemical conditions. Nodules from deeper sediment depth (>500 cm) consist primarily of todorokite and additionally show signs of dissolution. The transformation of phyllomanganates to todorokite and their further dissolution upon nodule burial under suboxic conditions induces modifications in the crystal-chemistry of Ni, Co, and Cu. In surface nodules, Ni and Co are incorporated in the octahedral sheets of phyllomanganates, whereas Cu mainly is located at the edges of those phyllomanganate sheets. In buried nodules Cu and to a lesser extent Ni are incorporated in todorokite by forming outer-sphere complexes within the tunnels. However, Ni is predominantly incorporated within the octahedra of the newly formed todorokite structure. Co is also enriched in the octahedra of todorokite as a result of dissolution of hydrogenetic vernadite and re-incorporation in the more stable Mn-phase formed during the diagenetic transformation. Co enrichment under suboxic conditions after burial within the sediments is noteworthy since Co in surface nodules is characteristic for oxic conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Shale as a Source of Organic Carbon in Floodplain Sediments of a Mountainous Watershed

Abstract Shales contain high levels of organic carbon (OC) and represent a large fraction of the Earth's reduced carbon stocks. While recent evidence suggests that shale‐derived OC may be actively cycled in riverine systems, this process is poorly understood and not currently considered in global C models. Through the use of sediment density fractionations, extractions, radiocarbon measurements, and chemical characterization, we provide information on the abundance, chemistry, and mobility of shale‐derived OC in floodplain sediments of a shale‐rich mountainous watershed. The heavy fraction of the sediment, representing mineral‐associated OC, is the largest (84 ± 6% of TOC) and oldest (Δ 14 C values −224 to −853‰) OC pool. Evidence of shale‐derived OC is observed in all sediment C pools (i.e., occluded light fraction, water‐soluble, and pyrophosphate‐extractable) except the free light fraction, which is entirely modern. Relatively consistent chemistry was observed across samples for extracted and density‐separated OC, despite wide ranges of Δ 14 C values. Carbon spectroscopy revealed that floodplain sediments had a higher degree of functionalized aromatic groups and lower carbonate content compared to shale collected nearby, consistent with chemical alteration and mixing with other C sources in the floodplain. We estimate that approximately 23–34% of sediment OC is derived from shale, with implications for other shale‐derived elements (e.g., N). This study demonstrates the important contribution of shale‐OC, particularly in environments with low litter inputs. The large impact of radiocarbon‐dead shale‐OC, which has a thermally altered chemical structure distinct from plant litter, on Δ 14 C values and reactivity of sediment‐OC must be considered.

Fox, Patricia M.↗

A Numerical Modeling Framework for Flocculation and Cohesive Sediment Transport in the Wave Bottom Boundary Layer

Flocculation, a critical process in coastal and estuarine systems, plays a significant role in sediment transport, nutrient cycling, and ecological health. This study develops a cohesive sediment transport modeling framework tailored to the wave bottom boundary layer under dilute and equilibrium conditions, explicitly incorporating flocculation effects via a Population Balance Equation (PBE). Using Direct Numerical Simulation, six baseline cases, each with a distinct sediment concentration profile resulting from a constant settling velocity and critical erosion shear stress, are generated to drive the PBE flocculation model for given floc yield strength and stickiness. Results reveal that flocculation significantly influences sediment concentration profiles promoting three distinct stages, well‐mixed, transition to lutocline, and well‐developed lutocline. At low concentrations with well‐mixed profiles, cohesive floc properties are less significant, and turbulence is a main flocculation driver. In contrast, as concentration increases, cohesive floc properties become crucial, facilitating lutocline formation. Here, the analysis also highlights limitations of depth‐averaged settling velocity as a parameterization. It is suitable for well‐mixed and transitional profiles but fails in well‐developed lutoclines, where empirical formulations that explicitly incorporate turbulent shear rate and sediment concentration better capture variability. This study underscores the necessity of incorporating flocculation effects into sediment transport models to enhance predictions of sediment dynamics in wave bottom boundary layers.

Penaloza‐Giraldo, Jorge A. [Oak Ridge National Lab↗

Sedimentation and Nonlinear Trapping in Texas Reservoirs Identified Using Remote Sensing and Bathymetric Survey Records

Decreasing reservoir storage capacity due to sedimentation poses great challenges to aging U.S. reservoirs, as it reduces the efficacy and reliability of their socio‐economic services. However, systematic assessments of reservoir sedimentation rates and associated issues remain limited because of sparse and infrequent bathymetry survey data. In this study, we use remote sensing‐driven estimates of sediment concentrations to identify regions experiencing rapid reservoir capacity loss, as observed in repeated bathymetry surveys. Our analysis focuses on Texas, where one of the most reliable state‐level reservoir capacity loss data sets is available through a unique long‐term monitoring program by the Texas Water Development Board. We find that reservoirs with large storage capacities and high sedimentation rate are concentrated in Northeast Texas. We also show that reduced forest, increased barren land, and erosive soil properties are co‐varying with high reservoir sedimentation rates. Temporal changes in the longitudinal gradient of the remotely sensed sediment flux highlight the nonlinear nature of sediment trapping processes, and can be used to estimate the reservoir storage capacity loss over time. In combination with standard bathymetry surveys, our approach shows potential for more cost‐effective and frequent assessment of reservoir storage loss.

Lee, Jiyong [ORNL] (ORCID:0000000198957406)↗