SEARCH · Search NASA

Results for “STRESS CONCENTRATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Plasticity analysis of fibrous composite laminates under thermomechanical loads

Elastic-plastic behavior of fibrous composite laminates is analyzed for coupled in-plane mechanical loads and uniform thermal changes. Constitutive equations of the individual fibrous layers are derived from a vanishing fiber diameter model that represents the essential axial constraint between the phases. This permits derivation of closed form equations for the overall yield condition, stress concentration factors, and instantaneous compliance. Thermoelastic properties of the phases and yield stress of the matrix phase are functions of temperature. The effect of the model assumptions on the predicted behavior of composite laminates is examined by comparing the calculated response under cyclic thermal changes to available theoretical results and experimental measurements.

Bahei-El-din, Yehia A.↗

NASA NTRS1995

Thermal barrier coating life modeling in aircraft gas turbine engines

Analytical models useful for predicting ceramic thermal barrier coating (TBC) spalling life in aircraft gas turbine engines are presented. Electron beam-physical vapor deposited (EB-PVD) and plasma sprayed TBC systems are discussed. TBC spalling was attributed to a combination of mechanisms such as metal oxidation at the ceramic-metal interface, ceramic-metal interface stress concentrations at free surfaces due to dissimilar materials, ceramic-metal interface stresses caused by local radius of curvature and interface roughness, material properties and mechanical behavior, transient temperature gradients across the ceramic layer and component design features. TBC spalling life analytical models were developed based on observations of TBC failure modes and plausible failure theories. TBC failure was assumed to occur when the imposed stresses exceeded the material strength (at or near the ceramic-metal interface). TBC failure knowledge gaps caused by lack of experimental evidence and analytical understanding are noted. The analytical models are considered initial engineering approaches that capture observed TBC failure trends.

Nissley, D. M.↗

NASA NTRS1974

Analysis of the three-point-bend test for materials with unequal tension and compression properties

Structural resins have moduli and strengths which are different in tension and compression. The three-point-bend test is used extensively in their characterization. An investigation is performed to derive all the equations needed for the analysis and test data reduction of the three-point-bend test. The governing equations are derived using well-known linear structural mechanics principles and are represented graphically. The stress concentration effects in the vicinity of the load point are investigated, and failure stress and failure initiation are examined.

Chamis, C. C.↗

NASA NTRS1983

Fabrication of low-cost Mod-OA wood composite wind turbine blades

The wood composite blades were fabricated by using epoxy resin-bonded laminates of Douglas fir veneers for the leading edge spar sections and honeycomb-cored birch plywood panels for the blade trailing edge or afterbody sections. The blade was joined to the wind turbine hub assembly by epoxy resin-bonded steel load take-off studs. The wood composite blades were installed in the Mod-OA wind turbine test facility at Kahuku, Hawaii. The wood composite blades have successfully completed high power (average of 150 kW) operations for an eighteen month period (nearly 8,000 hr) before replacement with another set of wood composite blades. The original set of blades was taken out of service because of the failure of the shank on one stud. An inspection of the blades at NASA-Lewis showed that the shank failure was caused by a high stress concentration at a corrosion pit on the shank fillet radius which resulted in fatigue stresses in excess of the endurance limit.

Lark, R. F.↗

NASA NTRS1989

Weld stresses beyond elastic limit: Materials discontinuity

When welded structures depend on properties beyond the elastic limit to qualify their ultimate safety factor, and weld-parent materials abruptly change at the interface, then stress discontinuity is inevitable. The stress concentration is mildly sensitive to material relative strain hardening and acutely sensitive to applied stress fields. Peak stresses occur on the weld surface, at the interface, and dissipate within a 0.01-inch band. When the stress is intense, the weld will always fracture at the interface. The analysis incorporates a classical mechanics model to more sharply define stress spikes within the bandwidth, and suggests a relative material index and Poisson's ratio related to strain hardening. Implications are discussed which are applicable to industries of high performance structures.

Verderaime, V.↗

NASA NTRS1977

Finite-element analysis of a weld-penetration problem

The stress concentration factor for a weld penetration defect is calculated by the finite-element method. A stress intensity factor is computed by use of the finite-element solution and the J-integral. The results are compared with experimental results.

Rogge, T. R.↗

NASA NTRS1984

ICAN: Integrated composites analyzer

The ICAN computer program performs all the essential aspects of mechanics/analysis/design of multilayered fiber composites. Modular, open-ended and user friendly, the program can handle a variety of composite systems having one type of fiber and one matrix as constituents as well as intraply and interply hybrid composite systems. It can also simulate isotropic layers by considering a primary composite system with negligible fiber volume content. This feature is specifically useful in modeling thin interply matrix layers. Hygrothermal conditions and various combinations of in-plane and bending loads can also be considered. Usage of this code is illustrated with a sample input and the generated output. Some key features of output are stress concentration factors around a circular hole, locations of probable delamination, a summary of the laminate failure stress analysis, free edge stresses, microstresses and ply stress/strain influence coefficients. These features make ICAN a powerful, cost-effective tool to analyze/design fiber composite structures and components.

Murthy, P. L. N.↗

NASA NTRS1984

ICAN - Integrated composites analyzer

Murthy, P. L. N.↗

NASA NTRS2011

Detecting Cracks in Ceramic Matrix Composites by Electrical Resistance

The majority of damage in SiC/SiC ceramic matrix composites subjected to monotonic tensile loads is in the form of distributed matrix cracks. These cracks initiate near stress concentrations, such as 90o fiber tows or large matrix pores and continue to accumulate with additional stress until matrix crack saturation is achieved. Such damage is difficult to detect with conventional nondestructive evaluation techniques (immersion ultrasonics, x-ray, etc.). Monitoring a specimen.s electrical resistance change provides an indirect approach for monitoring matrix crack density. Sylramic-iBN fiber- reinforced SiC composites with a melt infiltrated (MI) matrix were tensile tested at room temperature. Results showed an increase in resistance of more than 500% prior to fracture, which can be detected either in situ or post-damage. A relationship between resistance change and matrix crack density was also determined.

Smith, Craig↗

NASA NTRS2015

Correlation of Electrical Resistance to CMC Stress-Strain and Fracture Behavior Under High Heat-Flux Thermal and Stress Gradients

Because SiCSiC ceramic matrix composites (CMCs) are under consideration for use as turbine engine hot-section components in extreme environments, it becomes necessary to investigate their performance and damage morphologies under complex loading and environmental conditions. Monitoring of electrical resistance (ER) has been shown as an effective tool for detecting damage accumulation of woven melt-infiltrated SiCSiC CMCs. However, ER change under complicated thermo-mechanical loading is not well understood. In this study a systematic approach is taken to determine the capabilities of ER as a relevant non-destructive evaluation technique for high heat-flux testing, including thermal gradients and localized stress concentrations. Room temperature and high temperature, laser-based tensile tests were conducted in which stress-dependent damage locations were determined using modal acoustic emission (AE) monitoring and compared to full-field strain mapping using digital image correlation (DIC). This information is then compared with the results of in-situ ER monitoring, post-test ER inspection and fractography in order to correlate ER response to convoluted loading conditions and damage evolution.

electrical resistance↗

NASA NTRS2011

A Method of Strengthening Composite/Metal Joints

The term tape setback method denotes a method of designing and fabricating bonded joints between (1) box beams or other structural members made of laminated composite (matrix/ fiber) materials and (2) metal end fittings used to fasten these structural members to other structural members. The basic idea of the tape setback method is to mask the bonded interface between the metallic end fitting and composite member such that the bond does not extend out to the free edges of the composite member. The purpose served by the tape setback method is to strengthen the joints by decoupling stress concentrations from edge defects, which can cause premature failures. A related prior method that serves a similar purpose, involving the use of tapered adherends at the joints, can be too difficult and costly to be acceptable in some applications. The tape setback method offers an easier, less costly alternative. The structural members to which the method was originally applied were box beams in the form of composite tubes having flat faces with rounded corners. The end fittings were plugs made of a low-thermal- expansion nickel/iron alloy (see figure). In computational-simulation studies of tensile and compressive loading of members without tape setback, stresses were found to be concentrated at the free end edges of the composite tubes, and inspection of members that had been subjected to real tension and compression tests showed that cracks started at the free end edges. As applied to these members, the tape setback method makes them less vulnerable to initiation of failure at edge defects produced during fabrication. In real tension tests of comparable members without and with tape setback, the average mean tensile strength of the members with tape setback was found to be 1.9 times that of the members without tape setback.

Polis, Daniel L.↗

NASA NTRS2011

Detecting Damage in Ceramic Matrix Composites Using Electrical Resistance

The majority of damage in SiC/SiC ceramic matrix composites subjected to monotonic tensile loads is in the form of distributed matrix cracks. These cracks initiate near stress concentrations, such as 90 deg fiber tows or large matrix pores and continue to accumulate with additional stress until matrix crack saturation is achieved. Such damage is difficult to detect with conventional nondestructive evaluation techniques (immersion ultrasonics, x-ray, etc.). Monitoring a specimen.s electrical resistance change provides an indirect approach for monitoring matrix crack density. Sylramic-iBN fiber- reinforced SiC composites with a melt infiltrated (MI) matrix were tensile tested at room temperature. Results showed an increase in resistance of more than 500% prior to fracture, which can be detected either in situ or post-damage. A relationship between resistance change and matrix crack density was also determined.

Smith, Craig E.↗

NASA NTRS1986

A failure mechanism in Al-SiC composites

Divecha et al. (1981) have discussed the advantages of materials obtained by adding silicon carbide whiskers to commercial aluminum alloys, taking into account also certain problems which are related to poor ductility and low fracture toughness. The present investigation has the objective to advance the understanding of the deformation at the whisker ends in reinforced aluminum composites through both observation and analysis. It is suggested that the low fracture toughness of the considered materials is the result of the rapid accumulation of damage at the whisker ends. It is pointed out that the whisker ends are sites of severe stress concentration and intense localized plastic strain. In connection with this situation, voids nucleate and grow at relatively low macroscopic stress levels. The reported studies include an examination of the deformation microstructure beneath the fracture surfaces of specimens with the aid of transmission electron microscopy.

Nutt, S. R.↗

NASA NTRS1986

Stress patterns in an interplate shear zone - An effective anisotropic model and implications for the Transverse Ranges, California

The pervasive Quaternary strike-slip (or wrench) structure that occurs in southern California is analyzed by solving a series of planar, linear elastic boundary value problems of tractional type that assume pure shear forces at infinity. It is concluded that the cross-cutting tectonic fabric of the Transverse Ranges in southern California causes the Ranges to act as a stress concentrator. In addition, it is found that rigid rotation of the Transverse Ranges is mechanically supported by an asymmetric distribution of stress and elastic strain encircling it. It is noted that for Quaternary tectonic orientation, a clockwise sense to this rotation is expected.

Ivins, E. R.↗

NASA NTRS1990

The assessment of metal fiber reinforced polymeric composites

Because of their low cost, excellent electrical conductivity, high specific strength (strength/density), and high specific modulus (modulus/density) short metal fiber reinforced composites have enjoyed a widespread use in many critical applications such as automotive industry, aircraft manufacturing, national defense, and space technology. However, little data has been found in the study of short metal fibrous composites. Optimum fiber concentration in a resin matrix and fiber aspect ratio (length-to-diameter ratio) are often not available to a user. Stress concentration at short fiber ends is the other concern when the composite is applied to a load-bearing application. Fracture in such composites where the damage will be initiated or accumulated is usually difficult to be determined. An experimental investigation is therefore carefully designed and undertaken to systematically evaluate the mechanical properties as well as electrical properties. Inconel 601 (nickel based) metal fiber with a diameter of eight microns is used to reinforce commercially available thermoset polyester resin. Mechanical testing such as tensile, impact, and flexure tests along with electrical conductivity measurements is conducted to study the feasibility of using such composites. The advantages and limitations of applying chopped metal fiber reinforced polymeric composites are also discussed.

Chung, Wenchiang R.↗

NASA NTRS1997

Fiber Contraction Approaches for Improving CMC Proportional Limit

The fact that the service life of ceramic matrix composites (CMC) decreases dramatically for stresses above the CMC proportional limit has triggered a variety of research activities to develop microstructural approaches that can significantly improve this limit. As discussed in a previous report, both local and global approaches exist for hindering the propagation of cracks through the CMC matrix, the physical source for the proportional limit. Local approaches include: (1) minimizing fiber diameter and matrix modulus; (2) maximizing fiber volume fraction, fiber modulus, and matrix toughness; and (3) optimizing fiber-matrix interfacial shear strength; all of which should reduce the stress concentration at the tip of cracks pre existing or created in the matrix during CMC service. Global approaches, as with pre-stressed concrete, center on seeking mechanisms for utilizing the reinforcing fiber to subject the matrix to in-situ compressive stresses which will remain stable during CMC service. Demonstrated CMC examples for the viability of this residual stress approach are based on strain mismatches between the fiber and matrix in their free states, such as, thermal expansion mismatch and creep mismatch. However, these particular mismatch approaches are application limited in that the residual stresses from expansion mismatch are optimum only at low CMC service temperatures and the residual stresses from creep mismatch are typically unidirectional and difficult to implement in complex-shaped CMC.

DiCarlo, James A.↗

NASA NTRS2012

Thermostructural Evaluation of Joggle Region on the Shuttle Orbiter's Wing Leading Edge

An investigation was initiated to determine the cause of coating spallation occurring on the Shuttle Orbiter's wing leading edge panels in the slip-side joggle region. The coating spallation events were observed, post flight, on differing panels on different missions. As part of the investigation, the high re-entry heating occurring on the joggles was considered here as a possible cause. Thus, a thermostructural evaluation was conducted to determine the detailed state-of-stress in the joggle region during re-entry and the feasibility of a laboratory test on a local joggle specimen to replicate this state-of-stress. A detailed three-dimensional finite element model of a panel slip-side joggle region was developed. Parametric and sensitivity studies revealed significant stresses occur in the joggle during peak heating. A critical interlaminar normal stress concentration was predicted in the substrate at the coating interface and was confined to the curved joggle region. Specifically, the high interlaminar normal stress is identified to be the cause for the occurrence of failure in the form of local subsurface material separation occurring in the slip-side joggle. The predicted critical stresses are coincident with material separations that had been observed with microscopy in joggle specimens obtained from flight panels.

Walker, Sandra P.↗

NASA NTRS1983

Optimization of bonded joints

A procedure for minimizing the elastic shear stress concentration in adhesive lap joints is presented. The proposed method is based upon tapering the adherends to achieve smooth stiffness transitions and uniform shear stresses. Both single and double lap splices are considered, but numerical examples are restricted to the case of double lap joints. Nonisotropic materials and nonoptimum design limitations, such as minimum and maximum thickness adherends, load-line eccentricity, and peel stresses are treated, and typical results are presented.

Ojalvo, I. U.↗