SEARCH · Search NASA

Results for “SWEEP FREQUENCY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS2026

Aerodynamic Performance and Acoustic Impacts of Varying Tip Speeds and Tripping Conditions on Small Rotors in an Anechoic Hover Chamber

Performance and acoustic measurements were taken in a hover chamber for various optimum hovering rotors (OPT2) and a commercial-off-the-shelf (COTS) rotor. A total of 10 rotors are included in this report, all of which have two blades and a tip radius of 0.1905 m (7.5 in.). For the OPT2, results for three additive manufacturing methods of fabrication are presented: stereolithography(SLA) using Accura Xtreme, SLA using FormLabs 10K resin, and selective laser sintering (SLS) using mineral-filled PA12 nylon material. All but one set of rotors were designed with a trailing edge bluntness that is 3% of the chord length, and one set was designed with a bluntness that is 1% of the chord length. Spanwise boundary layer trips were applied to the SLA, FormLabs and COTS rotors. Performance comparisons between untripped and tripped configurations demonstrate the impact of boundary layer state on rotor efficiency. Acoustic results, including periodic and broadband noise components, are presented. The effects of tripping these rotors near the leading edge are also presented. For some of the rotors, acoustic spectra of tip speed sweeps are presented to show how the frequency content changes with tip speed. Amplitude and frequency scaling methods are used to collapse broadband spectra at various tip speeds towards a unified curve. These findings contribute to the understanding of small rotor aeroacoustics and provide valuable datasets for computational model validation in urban air mobility applications.

eVTOL↗

NASA NTRS1973

Automatic carrier acquisition system

An automatic carrier acquisition system for a phase locked loop (PLL) receiver is disclosed. It includes a local oscillator, which sweeps the receiver to tune across the carrier frequency uncertainty range until the carrier crosses the receiver IF reference. Such crossing is detected by an automatic acquisition detector. It receives the IF signal from the receiver as well as the IF reference. It includes a pair of multipliers which multiply the IF signal with the IF reference in phase and in quadrature. The outputs of the multipliers are filtered through bandpass filters and power detected. The output of the power detector has a signal dc component which is optimized with respect to the noise dc level by the selection of the time constants of the filters as a function of the sweep rate of the local oscillator.

Bunce, R. C.↗

NASA NTRS2021

Adaptive-Sweep Algorithm for Spacecraft Carrier Acquisition and Tracking: System Analysis and Implementation

This paper presents an adaptive-sweep algorithm that can be used in conjunction with a Phased-Lock Loop to acquire and track the carrier of a Binary Phase-shift Keying signal with residual carrier. This algorithm is useful in proximity links where no Doppler pre-compensation is available at the transmitter, and allows the receiver to acquire the incoming carrier even if the experienced Doppler shift is several orders of magnitude larger than the PLL bandwidth. Other applications for this algorithm include Multiple Uplink per Antenna at the Deep Space Network, and generation of observables (Doppler shift, Doppler rate, range rate) for in-situ navigation purposes. This paper enhances a previously presented adaptive-sweep algorithm and its performance analysis in two fronts. First, the algorithm now uses the direction function to automatically estimate the required frequency jump to achieve PLL lock. This enables a fully adaptive-sweep scheme in which system implementer does not need to manually select thresholds. On the other hand, we study the system performance in the presence of Additive White Gaussian Noise and derive necessary conditions for the system to operate at low signal-to-noise conditions. This allows us to create design rules that specify all parameters of the algorithm given a set of system-level requirements. To test the performance of the proposed algorithm, we implement it in GNU Radio, an open-source Software-Defined Radio that interfaces with several commercial radio peripherals. We use this implementation to demonstrate carrier lock and quantify system performance under different noise conditions. We also test the algorithm using open-loop recordings of two downlinks between the Lunar Reconnaissance Orbiter and the Deep Space Network. We show that even after large frequency jumps (tens of kHz), the proposed system is able to rapidly reacquire the carrier and continue operation.

Divsalar, Dariush↗

NASA NTRS1998

Liquid Motion in a Rotating Tank Experiment (LME)

The Liquid Motion Experiment (LME), which flew on STS 84 in May 1997, was an investigation of liquid motions in spinning, nutating tanks. LME was designed to quantify the effects of such liquid motions on the stability of spinning spacecraft, which are known to be adversely affected by the energy dissipated by the liquid motions. The LME hardware was essentially a spin table which could be forced to nutate at specified frequencies at a constant cone angle, independently of the spin rate. Cylindrical and spherical test tanks, partially filled with liquids of different viscosities, were located at the periphery of the spin table to simulate a spacecraft with off-axis propellant tanks; one set of tanks contained generic propellant management devices (PMDs). The primary quantitative data from the flight tests were the liquid-induced torques exerted on the tanks about radial and tangential axes through the center of the tank. Visual recordings of the liquid oscillations also provided qualitative information. The flight program incorporated two types of tests: sine sweep tests, in which the spin rate was held constant and the nutation frequency varied over a wide range; and sine dwell test, in which both the spin rate and the nutation frequency were held constant. The sine sweep tests were meant to investigate all the prominent liquid resonant oscillations and the damping of the resonances, and the sine dwell tests were meant to quantify the viscous energy dissipation rate of the liquid oscillations for steady state conditions. The LME flight data were compared to analytical results obtained from two companion IR&D programs at Southwest Research Institute. The comparisons indicated that the models predicted the observed liquid resonances, damping, and energy dissipation rates for many test conditions but not for all. It was concluded that improved models and CFD simulations are needed to resolve the differences. This work is ongoing under a current IR&D program.

Deffenbaugh, D. M.↗

NASA NTRS1973

The log-periodic array at the Clark Lake Radio Observatory

A log-periodic array, 3 km in length, is operating at Clark Lake Radio Observatory. It makes one-dimensional sweeps of the solar brightness distribution in the frequency range 20 to 65 MHz once per sec. The phasing of the array and the receiving system are described, as well as how the dynamic spectra are analyzed for the positions of solar radio sources. Simultaneous measurements at many frequencies enable the observer to remove the effects of ionospheric refraction and to obtain fundamental positions to an accuracy of about one arc min at decametric wavelengths. Fundamental positions are given for Cassiopeia A.

Erickson, W. C.↗

NASA NTRS1981

General purpose research rotor

An analytical study, under a NASA contract, is performed on an advanced flight research rotor (four-bladed, 54 ft in diameter, with bearingless rotor retention characteristics) to determine the sensitivity of total rotor characteristics such as vibratory hub loads, rotor horsepower, and blade loads, to parametric variability of the rotor configuration. The sensitivity of the rotor to various combinations of blade planform taper, percent of blade span that is tapered, tip sweep angle, built-in-twist, and torsional frequency is determined for specific configurations by randomly selecting combinations of these parameters. Characteristics of other intermediate rotor configurations are determined by a regression analysis. The results show that a wide range of rotor total performance characteristics can be obtained for a rotor trimmed to the same flight conditions. The regression equations predict total performance of the rotor very well and appear to be a useful analytical tool for rotor design optimization. Figures showing the results of the various tests are given along with a table of the regression coefficients.

Jones, R.↗

NASA NTRS2007

35-45 Giga Hertz Transceiver System for Phase and Magnitude Detection

Nondestructive evaluation (NDE) is the science and practice of examining an object in a way that the object's usefulness is not adversely affected. Different types of NDE methods exist but this thesis is based on microwave and millimeter wave NDE using imaging techniques. Microwave NDE is based on illuminating the object under test with a microwave signal and studying the various properties of the reflected signal from the object. This reflected signal contains some information about the inner structure of the object under test. This information may be contained in several parameters including the phase and magnitude of the reflected signal. The goal of this project is to design and build a Q-band coherent transceiver that is capable of measuring the reflected signal's phase and magnitude so that an image of the object under test may be reconstructed. From the several techniques that can be used to construct an image of the object under test, techniques of interest to this work include synthetic aperture focusing technique (SAFT) and microwave holography. The transceiver system should have the ability to sweep a large portion of Q-band frequency range in small frequency steps as quick as possible while the detected phase and magnitude of the reflected signal is very accurate. Several different designs were studied and the final schematic diagram of the transceiver system was determined. One of the most important modules that was designed, implemented and tested in the laboratory was an accurate phase/magnitude detector circuit. The compared results of the scans using the transceiver system and vector network analyzer (VNA) showed that this transceiver system has a great potential to replace a VNA for the purpose of microwave and millimeter wave imaging.

Beni, Aman Aflaki↗

NASA NTRS1974

Comparison of flight data and analysis for hingeless rotor regressive inplane mode stability

Analytical and experimental data obtained during the development of the AH-56A covering stability of the regressive inplane mode, including coupling with other modes such as body and rotor plunge are reported. Data were obtained on two distinctly different control systems; both gyro controlled, but one with feathering moment feedback and the other with direct flapping feedback. A review was made of analytical procedures employed in investigating the stability of this mode and a comparison was made of the analytical and experimental data. The effect of certain parameters including blade droop, sweep, delta 3, alpha 1, vehicle roll inertia, inplane frequency, and rpm and forward speed on the mode were also reviewed. It was shown that the stability of this mode is treatable by analysis and that adequate stability is achievable without recourse to auxiliary inplane damping devices.

Anderson, W. D.↗

NASA NTRS1975

Vibration of skewed cantilever plates and helicoidal shells

Theoretical vibration frequencies and mode shapes are obtained for skewed plates and helicoidal shells with a cantilever boundary. Using Hamilton's law of varying action, a power series solution is developed to obtain converged numerical results for the five lowest frequencies. Effects of geometrical variables such as aspect ratio, sweep angle and shell radius to thickness ratio are investigated. Accuracy of the solution method is substantiated by comparison with existing skewed plate spherical cap, and conical shell results.

Beres, D. P.↗

NASA NTRS1975

In-flight damping measurement

A new testing technique is described which can be applied in determining the damping coefficient of the critical vibration modes of an airplane in flight. The damping coefficient can be determined in several different ways from the same data using different features of a modified response curve which implies the possibility of checking one value against the other. The method introduces the effect of sweep rate in the driving system. This effect on the frequency response curve of the critical vibration mode and its various characteristics are used in the determination of damping coefficient. A theoretical examination is made of these characteristics for single degree of freedom systems.

Sanderson, G. E.↗

NASA NTRS1981

Preliminary results of buffet tests in a cryogenic wind tunnel

Buffet tests of two wings with different leading-edge sweep show that it is feasible to use the standards wing root bending moment technique in a cryogenic wing tunnel. The results for the 65 deg sweep delta wing indicate the importance of matching the reduced frequency parameter in model tests for planforms which are sensitive to reduced frequency parameter if quantitative buffet measurements are required. The unique ability of a pressurized cryogenic wind tunnel to separate the effects of Reynolds number and of aeroelastic distortion by variations in the tunnel stagnation temperature and pressure was demonstrated.

Boyden, R. P.↗

NASA NTRS2000

Comparison of Analytical and CAA Solution(s): Unsteady Response of a Rectilinear Swept Cascade to an Incident Gust

This problem is aimed at testing the ability of computational aeroacoustic methods to calculate the acoustic pressure field generated as a result of the interaction of a convected harmonic gust with a rectilinear cascade of swept flat plates. All relevant geometric information is the same as the unsteady response of an isolated finite span swept airfoil to an incident gust problem with the exception of the sweep angle alpha, which is now taken to be a variable. Assume a cascade stagger angle of zero (with the x-axis aligned with the chord) and a gap-to-chord ratio of h/c = 1. The mean flow Mach number M(sub 0), gust frequency omega, gust amplitude A, and chordwise wavenumber k(sub x) are the same. But for the cascade problem take k(sub y) = pi and k(sub z) = 0. The appropriate physical scales are also the same, as is the governing equation and boundary conditions. Naturally, the impermeability condition now applies to the entire cascade. For this problem, determine the amplitude of upstream-radiated rms acoustic pressure as a function of the sweep angle at the specified frequency. Specifically, show the variations of rms acoustic pressure amplitude at the upstream location (-5c, 0, l/2) for sweep angle alpha in the range (0.0 deg, 30.0 deg). Use sweep angle increments no larger than 2.5 deg. Express the results in dB using the rms pressure value for alpha = 0.0 deg as the reference level. The appropriate FORTRAN output statement should read "WRITE(IUNIT,*) alpha, 20-log10 (p(sub rms)(alpha)/p(sub rms)(0))".

Envia, Edmane↗

NASA NTRS2014

Investigation of Active Flow Control to Improve Aerodynamic Performance of Oscillating Wings

The objective of this effort is to design a promising active flow control concept on an oscillating airfoil for on-blade alleviation of dynamic stall. The concept must be designed for a range of representative Mach numbers (0.2 to 0.5) and representative reduced frequency characteristics of a full-scale rotorcraft. Specifications for a sweeping-jet actuator to mitigate the detrimental effects of retreating blade stall experienced by edgewise rotors in forward flight has been performed. Wind tunnel modifications have been designed to accommodate a 5x6 test section in the Oran W. Nicks Low Speed Wind Tunnel at Texas A&M University that will allow the tunnel to achieve Mach 0.5. The flow control design is for a two-dimensional oscillating VR-7 blade section with a 15- inch chord at rotor-relevant flow conditions covering the range of reduced frequencies from 0.0 to 0.15 and Mach numbers from 0.2 to 0.5. A Computational Fluid Dynamics (CFD) analysis has been performed to influence the placement of the flow control devices for optimal effectiveness.

Narducci, Robert P.↗

NASA NTRS1988

The effects of excitation waveforms and shaker moving mass on the measured modal characteristics of a 2- by 5-foot aluminum plate

Ground vibration tests were conducted to compare and to investigate the effects of five excitation waveforms and the shaker moving mass (equipment and armature used to attach the shaker to the structure) on the experimental modal characteristics of a 2- by 5-ft aluminum plate using fast Fourier transform techniques. The five types of excitation waveforms studied were sine dwell, random, impact, sine sweep, and impulsive sine. The results showed that the experimental modal frequencies for all types of excitation were within 3 percent, while the modal damping data exhibited greater scatter. The sets of mode shapes obtained by the five types of excitation were consistent. The results of the shaker moving mass investigation on the 2- by 5-ft aluminum plate showed that modal frequency decreases and modal damping remains relatively constant with an increase in shaker moving mass. The generalized mass of the structure appears to decrease with an increase in shaker moving mass. In addition, it was seen that having a shaker near a node line can reduce some of the effects of the added shaker moving mass on the frequencies and the damping.

Voracek, David F.↗

NASA NTRS1992

Acoustophoresis method and apparatus

A method and apparatus are provided for acoustophoresis, i.e., the separation of species via acoustic waves. An ultrasonic transducer applies an acoustic wave to one end of a sample container containing at least two species having different acoustic absorptions. The wave has a frequency tuned to or harmonized with the point of resonance of the species to be separated. This wave caused the species to be driven to an opposite end of the sample container for removal. A second ultrasonic transducer may be provided to apply a second, oppositely directed acoustic wave to prevent undesired streaming. In addition, a radio frequency tuned to the mechanical resonance and coupled with a magnetic field can serve to identify a species in a medium comprising species with similar absorption coefficients, whereby an acoustic wave having a frequency corresponding to this gyrational rate can then be applied to sweep the identified species to one end of the container for removal.

Heyman, Joseph S.↗

NASA NTRS1993

Acoustophoresis separation method

A method and apparatus are provided for acoustophoresis, i.e., the separation of species via acoustic waves. An ultrasonic transducer applies an acoustic wave to one end of a sample container containing at least two species having different acoustic absorptions. The wave has a frequency tuned to or harmonized with the point of resonance of the species to be separated. This wave causes the species to be driven to an opposite end of the sample container for removal. A second ultrasonic transducer may be provided to apply a second, oppositely directed acoustic wave to prevent undesired streaming. In addition, a radio frequency tuned to the mechanical resonance and coupled with a magnetic field can serve to identify a species in a medium comprising species with similar absorption coefficients, whereby an acoustic wave having a frequency corresponding to this gyrational rate can then be applied to sweep the identified species to one end of the container for removal.

Heyman, Joseph S.↗

NASA NTRS1988

Parametric studies of advanced turboprops

The effects of geometric variables (sweep and twist) on the structural performance of advanced turboprops are investigated. The investigation is limited to aerodynamically efficient turboprops using an acceptable design configuration as a baseline. The baseline configuration is modified using a seven by seven array of independently varying sweep and twist parameters while maintaining acceptable aerodynamic efficiency. The turboprop structural performance is evaluated in terms of critical speeds, tip displacements, and vibration frequencies where geometric nonlinearities are included. The results obtained are presented in such a manner as to highlight the effects of sweep and twist on the structural performance of aerodynamically efficient turboprop configurations.

Fertis, D. G.↗

NASA NTRS1988

Parametric studies of advanced turboprops

Maser, J. G.↗