Search NASA⌕ Search

SEARCH · Search NASA

Results for “Scale-up”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

180 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Pre-demonstration Development of Controlled-Release Corrosion Inhibitors and Healing Agents as Alternatives to Hexavalent Chromium

This Limited Scope Study was directed to achieve the following objectives:(1) Scale-up of materials that can meet MIL-PRF-23377 (solvent-based primer).(2) Provide evidence of resistance to aircraft alkaline cleaners and deicing fluids.(3) Provide formulation for initial ecological and toxicity screening.(4) Submit an interim report that will provide the basis for a future ESTCP demonstration effort.The encapsulation procedure for two corrosion inhibitors was scaled up from lab scale to 2.0 kg. This scale will accommodate high volume production of coatings with encapsulated corrosion inhibitors for large surface areas during a follow on ESTCP demonstration effort.Test results provided evidence of resistance to alkaline cleaners and aircraft deicing fluids and compliance with MIL-PRF-23377. All the MIL-PRF-23377 requirements were met with the exception of the adhesion requirement, in top coated panels, and the flexibility requirement. Work on solving these two problems will be done prior to validation and demonstration of the technology. An initial ecological and toxicity screening identified several factors that were not critical to the acceptance of the encapsulated corrosion inhibitor. This new technology will lead to environmentally friendly alternatives to hexavalent chromium that will enable DoD to protect its assets. Field demonstration, licensing, qualification, and commercialization will allow its real world utilization.

Calle, L. M.↗
NASA NTRSDate not supplied

Fire Front Detection and Tracking for Autonomous sUAS in STEReO

The Scalable Traffic Management Emergency Response Operations (STEReO) project aims to incorporate unmanned aerial systems (UAS) into wildfire incident response to safely quicken response times, improve operator awareness, and scale-up aircraft operations.Autonomous UAS can be used to relieve human operators of dull, dirty, and dangerous tasks such as checking for re-ignitions and geo-locating fires. To geo-locate fires, the UAS must be able to detect whether a fire is present and also have the necessary information to stamp a location. Furthermore, the UAS should be able to track the fire front to determine the extent of the fire. This study presents a fire front detection and tracking methodology for an autonomous small UAS (sUAS). The methodology is evaluated in simulation.

Autonomous UAV,Wildfire,Detection,Tracking↗
NASA NTRSDate not supplied

Development and Characterization of the Integrally Stiffened Cylinder (ISC) Process for Launch Vehicles and Aircraft Fuselage Structures

Over the past decade, NASA Langley has led development of the Integrally Stiffened Cylinder (ISC) Process, a near-net shape, flow-forming technology. This innovative process is being evaluated for launch vehicle and commercial aircraft manufacturing. A thick-walled, cylindrical preform is flow-formed in a single operation into a thin-walled barrel with longitudinal stiffeners. The one-piece, stiffened barrels offer a direct replacement for conventional multi-piece welded or riveted structures. A cost-benefit analysis for launch vehicles estimated that the ISC process offers up to a 50% reduction in manufacturing costs and a 10% reduction in mass. NASA, the European Space Agency (ESA), and industry partners have teamed to manufacture 10-ft. diameter aluminum ISCs. The intent is to demonstrate the commercial viability of the process at a scale relevant to the commercial launch and aircraft industries. Development activities will be presented, including process scale-up, formability assessment, microstructural analysis, and mechanical property testing.

ISC, flow forming, near net shape↗
NASA NTRS2018

Pre-Demonstration Development of Controlled-Release Corrosion Inhibitors and Healing Agents as Alternatives to Hexavalent Chromium

This Limited Scope Study was directed to achieve the following objectives: (1) Scale-up of materials that can meet MIL-PRF-23377 (solvent-based primer). (2) Provide evidence of resistance to aircraft alkaline cleaners and deicing fluids. (3) Provide formulation for initial ecological and toxicity screening. (4) Submit an interim report that will provide the basis for a future ESTCP demonstration effort. The encapsulation procedure for two corrosion inhibitors was scaled up from lab scale to 2.0 kg. This scale will accommodate high volume production of coatings with encapsulated corrosion inhibitors for large surface areas during a follow on ESTCP demonstration effort. Test results provided evidence of resistance to alkaline cleaners and aircraft deicing fluids and compliance with MIL-PRF-23377. All the MIL-PRF-23377 requirements were met with the exception of the adhesion requirement, in top coated panels, and the flexibility requirement. Work on solving these two problems will be done prior to validation and demonstration of the technology. An initial ecological and toxicity screening identified several factors that were not critical to the acceptance of the encapsulated corrosion inhibitor. This new technology will lead to environmentally friendly alternatives to hexavalent chromium that will enable DoD to protect its assets. Field demonstration, licensing, qualification, and commercialization will allow its real world utilization.

Alternatives to Hexavalent Chromium↗
NASA NTRSDate not supplied

Pre-Demonstration Development of Controlled-Release Corrosion Inhibitors and Healing Agents as Alternatives to Hexavalent Chromium

This Limited Scope Study was directed to achieve the following objectives: (1) Scale-up of materials that can meet MIL-PRF-23377 (solvent-based primer). (2) Provide evidence of resistance to aircraft alkaline cleaners and deicing fluids. (3) Provide formulation for initial ecological and toxicity screening. (4) Submit an interim report that will provide the basis for a future ESTCP demonstration effort. The encapsulation procedure for two corrosion inhibitors was scaled up from lab scale to 2.0 kg. This scale will accommodate high volume production of coatings with encapsulated corrosion inhibitors for large surface areas during a follow on ESTCP demonstration effort. Test results provided evidence of resistance to alkaline cleaners and aircraft deicing fluids and compliance with MIL-PRF-23377. All the MIL-PRF-23377 requirements were met with the exception of the adhesion requirement, in top coated panels, and the flexibility requirement. Work on solving these two problems will be done prior to validation and demonstration of the technology. An initial ecological and toxicity screening identified several factors that were not critical to the acceptance of the encapsulated corrosion inhibitor. This new technology will lead to environmentally friendly alternatives to hexavalent chromium that will enable DoD to protect its assets. Field demonstration, licensing, qualification, and commercialization will allow its real world utilization.

Alternatives to Hexavalent Chromium, Controlled Re↗
NASA NTRSDate not supplied

Development and Characterization of the Integrally Stiffened Cylinder (ISC) Process for Launch Vehicles and Aircraft Fuselage Structures

Over the past decade, NASA Langley has led development of the Integrally Stiffened Cylinder (ISC) Process, a near-net-shape, flow-forming technology. This innovative process is being evaluated for launch vehicle and commercial aircraft manufacturing. A thick-walled, cylindrical preform is flow-formed using a single operation into a thin-walled barrel with integral longitudinal stiffeners. The one-piece, stiffened barrels offer a direct replacement for conventional multi-piece, welded or riveted structures. A cost-benefit analysis for launch vehicle cryogenic propellant tanks estimated that the ISC process offers up to a 50% reduction in manufacturing costs and a 10% reduction in mass. NASA, the European Space Agency (ESA), and industry partners have teamed to manufacture 3-m(10-ft.) diameter aluminum ISCs. The intent is to demonstrate the commercial viability of the process at a scale relevant to the commercial launch and aircraft industries. Development activities will be presented, including process scale-up, formability assessment, and mechanical property testing.

ISC, flow forming, near net shape↗
NASA NTRSDate not supplied

Development of a Cold-Walled Molten Regolith Electrolysis Reactor for Lunar Oxygen Production

On the lunar surface, production of commodi-ties to support human presence, such as water, food and oxygen, and sustain the growth of a per-manent outpostwill likely require the use oflocal resources. The moon is covered almost entirely withfragmented oxide minerals known as regolithhundreds of meter thick.As a resource, it is rich in oxygen (> 42 wt.%) bound in a solid state with a variety of metals. The molten regolith electrolysis (MRE)reactor is a promising technology for the production of gaseous oxygen from the lunar reg-olithin a simple, single-stepreaction that requires minimalconsumable materials, produces oxygen and metals with high electrical efficiency and high yields from any regolithcomposition.This process involvesmelting regolith to~1600°C then electro-lyzing the molten pool to separate metal and oxy-gen ions that are then collected as liquid metal and gaseous oxygen at the respective electrodes. Lab-scale demonstrations of the MRE technology have previously reliedon external heating sources to bring the entirety of the reactor up to the operating temperaturewhich creates corrosive interfaces be-tween the molten regolith and the containment ma-terial in the reactor, limiting the overall lifespan of a reactor[1]. The Gaseous Lunar Oxygen from Regolith Electrolysis (GaLORE) project is focused on the development of a “cold-walled” or “Joule-heated” reactor design in which an internal heating source is used to selectively melt a pool of regolith between the electrodes of the reactor, leaving a shell of solidified regolith between the molten pool and the containment vessel of the reactor. This next generation reactor concept has been under development as molten oxide electrolysis (MOE) by MIT and Boston Metal for the production of iron from pure ores for terrestrial application [2]. The GaLORE project in engaged in early development of the technology for use with varying lunar regolith compositionsin the lunar environment. Thermal modelling of a proposed cold-walledreac-tor design were used as a scaffold to develop pa-rameters for a feasible reactor shape and size as well as target energy consumption[3]. The current development effort for the cold-walled reactor de-sign will be presented as a trade study of the most promising techniques for melting regolithwithin the constraints imposed by the lunar environment.Heater devices are designed to accommodate lim-ited electrical power availabilityon the moon, a wide range of regolith compositions that may be seen on the moon, limited metals available for re-placing consumed parts,and the low thermal con-ductivity of granular regolith in vacuum.Heater de-vices will be down-selectedbased on performance measurements within the above operationalcon-straints,and selected devices will be integrated into a reactor with electrodes to begin producing oxygen. [1]Sibille,L.,Sadoway, D.R.,Sirk, A., Tripathy,P.,Melendez, O., Standish, E., Dominguez, J. A., Stefanescu, D.M.,Curreri, P.A., Poizeau,S.,2009. “Recent Advancesin Scale-up Development of Molten Regolith Electrolysis for Oxygen Production in support of a Lunar Base.”AIAA 2009-659, 47th AIAA Aerospace Sciences Meeting, 5 -8 January 2009, Orlando, FL. [2] Boston Metal, https://www.boston-metal.com/moe-technology/#moe-process[3]Schreiner, S.S.,Sibille, L., Dominguez, J.A., Hoffman, J.A., 2016. "A parametric sizing model for Molten Regolith Electrolysis reactors to pro-duce oxygen on the Moon." Advances in Space Research 57.,7,1585-1603.

K D Grossman↗
NASA NTRSDate not supplied

Pragmatic Stress Prediction on Additively Manufactured Coupons

Prediction of residual stresses from process parameters for additively manufactured large metal parts is computationally expensive. NASA is currently developing meter-scale parts with direct energy deposition. Practically, the predictive computational methods need to efficiently scale-up to meter-scale parts. Coupled thermal-mechanical multi-physics simulations have been developed with the pragmatic method using ABAQUS, COMSOL Multiphysics, ALE3D software. The residual stresses are a result of the manufacturing process which creates thermal cycling of the build layers. The pragmatic method uses lumped thermal layers for stress predictions to reduce computational costs. The stress predictions as well as deformations of the different codes are compared with each other and with ANSYS Additive using identical material models, boundary and initial conditions. The codes were used to simulate three different geometries: a thin wall, hollow cylinder and twin-cantilever part. The coupon parts were then manufactured with Inconel-625. The residual stresses in these parts were measured using X-ray diffraction as well as neutron beam diffraction at NIST. The stress measurements for the two technologies are compared. The pragmatic stress prediction method enabled predictions of the multi-centimeter scale parts using desktop computer workstations in only a few hours for each coupon. The results of the simulated stress predictions compared favorably with the measured stresses even though thermally lumped layers were employed. Finally, a two-meter scale nozzle was simulated using ANSYS Additive. The simulations were used to examine the build orientation trade-space with respect to resulting geometric deformation. The predicted deformations were compared to measurements of an actual subscale part manufactured with direct energy deposition.

Additive Manufacturing↗
NASA NTRSDate not supplied

Extensibility of PICA TPS for Future Sample Return Missions

Stardust was the first successful robotic sample return mission delivering samples of the Comet Wild 2 to Earth in 2006. Genesis followed Stardust, in the era of “faster, better, cheaper,” collecting samples of solar wind. The Genesis sample return capsule (SRC) was larger and the program did not have the time nor funding to scale up the Stardust PICA heatshield and so, utilized an alternate heatshield. The successful Stardust mission led to future mission concepts baselining Stardust EDL, especially the entry heatshield. OSIRIS REx, was one such concept and the mission was designed to include build-to-print elements of the Stardust design. The primary scale-up limitation beyond Stardust and OSIRIS REx is the single-piece net cast PICA heatshield. In the past three years, FMI working with NASA Ames, expanded the manufacturing capability of PICA and demonstrated a 1.3 m PICA single piece TPS. This was done in anticipation of the Mars Sample Return mission as well as future Sample Return missions requiring larger-scale SRCs. This effort also identified a sustainable domestic replacement precursor for the PICA preform as the heritage precursor was discontinued in 2016 and FMI has gone through multiple rayon replacements since Stardust. As part of the effort, PICA was also tested at conditions higher than the Stardust or OSIRIS REx entry envelope to establish an expanded performance envelope and enable future sample return missions at higher entry speeds. The poster will highlight PICA sustainability and extensibility as part of the Sample Return to Earth session.

PICA thermal protection↗
NASA NTRSDate not supplied

Pragmatic Stress Prediction on Additively Manufactured Coupons

Prediction of residual stresses from process parameters for additively manufactured large metal parts is computationally expensive. NASA is currently developing meter-scale parts with direct energy deposition. Practically, the predictive computational methods need to efficiently scale-up to meter-scale parts. Coupled thermal-mechanical multi-physics simulations have been developed with the pragmatic method using ABAQUS, COMSOL Multiphysics, ALE3D software. The residual stresses are a result of the manufacturing process which creates thermal cycling of the build layers. The pragmatic method uses lumped thermal layers for stress predictions to reduce computational costs. The stress predictions as well as deformations of the different codes are compared with each other and with ANSYS Additive using identical material models, boundary and initial conditions. The codes were used to simulate three different geometries: a thin wall, hollow cylinder and twin-cantilever part. The coupon parts were then manufactured with Inconel-625. The residual stresses in these parts were measured using X-ray diffraction as well as neutron beam diffraction at NIST. The stress measurements for the two technologies are compared. The pragmatic stress prediction method enabled predictions of the multi-centimeter scale parts using desktop computer workstations in only a few hours for each coupon. The results of the simulated stress predictions compared favorably with the measured stresses even though thermally lumped layers were employed. Finally, a two-meter scale nozzle was simulated using ANSYS Additive. The simulations were used to examine the build orientation trade-space with respect to resulting geometric deformation. The predicted deformations were compared to measurements of an actual subscale part manufactured with direct energy deposition.

pragmatic method↗
NASA NTRSDate not supplied

Challenges in Scaling Analysis from Coupons to Elements in 3D Woven Composites for a Launch Vehicle End-Ring Structure

The limitations of structural design with 3D woven composites based on homogenized material models characterized using coupon test data, representative unit cell analysis, or a combination of the two are discussed in the context of a space launch system (SLS)-scale end ring. Selected building block test configurations at the coupon, element, and subcomponent scales are described in detail. Highly instrumented tests and X-ray computed tomography inspections are used to characterize the structural behavior and associated damage progression with increasing load. It is shown that a single homogenized material constitutive relationship, applied at coupon and element scale, is not sufficient to model the structural response observed in both tests. In fact, substantially different stress-strain laws are required to predict the response of the coupon and element scale specimens, despite similar loading conditions. A model with discrete representation of the binder tows and cohesive interfaces to model matrix cracking shows much better agreement with the test data at the two length scales. Thus, evidence is provided showing that predictive structural analysis of 3D woven composites requires discrete representation of the tows, matrix cracking morphology, and their interactions in the structural configuration. With accurate knowledge of the element scale behavior, engineering approximations readily enable analysis scale-up to the subcomponent level.

Andrew C Bergan↗
NASA NTRSDate not supplied

Development of Additive Manufacturing Technologies for 3D Printing of Spacecraft Heat Shields

Introduction: Ablative heat shields are an enabling technology for entry into planetary atmospheres. From the PICA heatshields used for several Mars rovers to the carbon phenolic material used for Galileo’s Jupiter entry probe, the heat shield manages the heat load transferred to the payload, protecting the sensitive scientific instruments carried on entry probes. The Additive Manufacturing of Thermal Protection Systems (AMTPS) project, an Early Career Initiative (ECI) funded by NASA’s Space Technology Mission Directorate and led by NASA Johnson Space Center, seeks to develop materials and processes for 3D printing ablative heat shields for spacecraft. Current methods for producing ablative heat shields are extremely labor intensive and re-quire extensive hands-on processes and quality control characterization. Additive manufacturing (AM) offers the possibility of reduced production times, improved reliability, and enhanced performance via graded compositions. Costs will also be reduced by reducing the time and labor required for heat shield production. Direct integration of the heat shield onto the structure during processing simplifies integration and reduces risk. Material Development: A critical challenge for the project is development of a material system that can (1) be printed in a near-net shape process and (2) perform well as an ablator. Achieving printability requires the material to flow under applied pressure, but maintain its shape once extruded from the printer nozzle. Ablative performance is measured by a multitude of markers, including char yield, char strength, thermal conductivity, and recession rate. Furthermore, there are several mechanical and thermal property considerations for vehicle integration including coefficient of thermal expansion (CTE) and residual stress. AM technology will be leveraged to grade the material formulation and properties through the thickness of the heat shield, an architecture not possible with current manufacturing processes. To this end, “robust” material formulations have been pre-pared with higher density for use on the surface where most ablation will occur. “Insulative” material formulations, with lower density and lower thermal conductivity, are prepared for use in the depth of the heat shield. This graded architecture will re-duce the overall mass of the heat shield and reduce costs and/or increase scientific payload capacities. To achieve a material system with the required properties, multiple resins have been investigated in collaboration with NASA Ames Research Center. To tune printability and performance, resin additives were studied to improve flexibility of the cured material while maintaining acceptable ablative performance. Material coupons were printed and studied via a suite of mechanical and thermal characterization methods. Arc jet testing was conducted at NASA Ames Research Center to evaluate ablative performance and thermal protection under conditions expected in atmospheric entry. Manufacturing Scale-Up: A partnership with Oak Ridge National Laboratory (ORNL) aims to enable full-scale fabrication of a 3D printed heat shield. Leveraging expertise in manufacturing and 3D printing at ORNL, a mid-scale manufacturing demonstration unit will be built and tested, using a dual-layer ablative system printed directly onto the titanium structure. Work on robotic system integration is ongoing and efforts to scale up material mixing with a material compound will ensure accurate and homogenous composition. Flight Test: A hypersonic sub-orbital flight test will provide a rigorous test of material performance ranging from ablation, thermal management, and mechanical integrity. Design of the capsule has taken place in collaboration with the University of Kentucky. Data collected from the flight will inform future design efforts in material formulation, printing methodology, and heat shield-capsule integration.

additive manufacturing↗
NASA NTRSDate not supplied

Status of the Development of 3MDCP, the 3-D Woven TPS enabling the Mars Sample Return Earth Entry System

- The Mars Sample Return Earth Entry System is being designed to withstand entry environments of: - Peak Heat Flux of > 3000 W/cm2 - Peak Dynamic Pressure of > 2 atmospheres - Peak Shear of > 3000 Pa. - The TPS Material System Selected to support MSR EES is “3MDCP”, 3D Mid Density Carbon Phenolic. 3MDCP is a derivative of the HEEET material system, using the “Insulation Layer” only. - Implementation of 3MDCP on EES is monolithic instead of a tile architecture in order to meet MSR reliability demands. - The EES TPS Team has recently completed a number of major engineering development milestones in support of delivering the flight 3MDCP TPS hardware: - Weaving Scale-Up completed, > 80” width woven preform production underway - Full Scale Forming & Manufacturing Attrition completed to verify delivered thickness capabilities. - Recent Design Change: EES design has been changed from a 45 degree sphere cone to a 52.5 degree sphere cone to allow for additional system mass.

Z. Young↗
NASA NTRSDate not supplied

Solid-state Architecture Batteries for Enhanced Rechargeability and Safety (SABERS) Beyond Li-Ion: Technology to Enable Sustainable Electric Aviation

All-electric and hybrid electric aerovehicle concepts face numerous technical barriers prior to their introduction into the consumer marketplace in order to meet sustainable aviation goals. One of the primary barriers to overcome is developing an energy dense storage system capable of meeting the rigorous aerospace safety and performance criteria. Additionally, the electric aviation market requires that the batteries be fabricated in a sustainable manner with materials that are readily available and abundant within the U.S. to ensure there are no supply chain issues during manufacturing. The performance metrics to enable electric aviation are at least two times greater than those of electric ground vehicles. Furthermore, inherently non-flammable batteries are essential for safe operation of commercial electric aerovehicles. The SABERS concept proposes a battery that meets the key performance criteria through development of a solid-state architecture battery utilizing high-capacity sulfur-selenium cathode and lithium metal anode. The combination of sulfur and selenium offers a balanced energy-to-power density ratio, which can be tailored to the specific application by altering the stoichiometric ratios of sulfur to selenium. The hybrid cathode has been developed by implementing NASA patented holey graphene technology as a highly conductive, ultra-lightweight electrode scaffold. A solid-state electrolyte has been used as a safe, non-flammable replacement to the highly flammable liquid organic electrolytes currently used in SOA lithium-ion batteries. This solid-state lithium-sulfur/selenium cell will be designed into a serial stacking configuration to enable dense packaging of the battery cells. The serial stacking configuration is termed a bipolar stack, which has the advantages of reducing overall cell weight, simplifying the interfaced connections for the cell, and minimizing the cooling requirements. Lastly, optimization of battery components will occur through a robust and rigorous combination of various computational modeling techniques covering multiple length scales. The expected result will be a fully solid-state battery with operational temperatures up to 150 °C which provides the required energy density, discharge rates, and inherent safety to meet the strict aerospace mission performance criteria. This poster summarizes recent results from battery component optimization to scale-up production of full SABERS pouch cells.

Urban Air Mobility (UAM) Vehicles↗
NASA NTRSDate not supplied

Data Quality Challenges for Analysis Ready Data (ARD)

Data quality plays a critical role in research and applications. The Earth Science Information Partners (ESIP) Information Quality Cluster (IQC) defines four aspects of information quality: Science, Product, Stewardship, and Services. The ESIP IQC has become internationally recognized as an authoritative and responsive resource of information and guidance to data producers and distributors on how to implement data quality standards and best practices for their science data systems, datasets, and data/metadata dissemination services. In recent years, cloud computing environments have provided scale-up capabilities such as data archives and services, enabling interdisciplinary science and applications. More value-added products are expected from data service providers, including Analysis Ready Data (ARD). ARD refers to data that has been preprocessed into a form that allows immediate analysis by the end user, processed to a minimum set of requirements and provides interoperability over time and across multiple datasets. Once a dataset has been developed from its original form to produce ARD, what quality characteristics should the derived dataset or ARD possess? Also, is it safe to assume that the quality of the ARD is consistent with the quality of the source data, or are there special attributes to an ARD that would warrant a secondary, independent quality assessment? What provenance (also called “data lineage”) information needs to be included in ARD? It is important to answer these questions, especially given the ease of use of ARD, and the consequent temptation by users to trust ARD without understanding the limitations or possible variations in quality compared to the source data. In this presentation, we will discuss data quality challenges for ARD products and services and introduce IQC for participation.

data quality↗
NASA NTRSDate not supplied

Experimental Investigation of a Physisorption-Based Hydrogen Storage System

This study discusses a practical system utilizing the principle of physisorption where hydrogen is weakly bound to the surface of a nanoporous silica aerogel blanket as an alternative to high-pressure and cryogenic hydrogen storage. Three different experiments are conducted to simulate various scenarios of such a storage method: change in pressure and change of scale. Transient responses of the charging and discharging cycles are of particular interest. It is observed that hydrogen uptake can be increased by up to 36-38 % at ambient conditions and 77 K when utilizing the aerogel blankets. Packing density, or the artificial increase of surface per volume, increases storage capacity as it is a mainly surface-driven phenomenon. High-pressure testing up to 50 bar showed benefits of the aerogel addition whereas the maximum uptake improvement was observed for 2 bar with a 105.3 % improvement over an empty vessel at identical conditions corresponding to 6.43 wt%. The scale-up of the system is highly sensitive to the design of the internal cooling design as aerogels are poor thermal conductors reducing the transient response of such systems. Furthermore, the high mass of metal-based pressure vessels further delays the thermal response. This makes the system suitable for day to week-long hydrogen storage but not for peak-shaving or load balancing.

Marcel Otto↗
NASA NTRS2024

Improved Mechanical Performance in FDM Cellular Frame Structures through Partial Incorporation of Faces

The utilization of lattice-type cellular architectures has seen a significant increase, owing to their predictable shape and the ability to fabricate templated porous materials through low-cost 3D-printing methods. Frames based on atomic lattice structures such as face-centered cubic (FCC), body-centered cubic (BCC), or simple cubic (SC) have been utilized. In FDM, the mechanical performance has been impeded by stress concentration at the nodes and melt-solidification interfaces arising from layer-by-layer deposition. Adding plates to the frames has resulted in improvements with a concurrent increase in weight and hot-pocket-induced dimensional impact in the closed cells formed. In this paper, we explore compressive performance from the partial addition of plates to the frames of a SC-BCC lattice. Compression testing of both single unit cells and 4 × 4 × 4 lattices in all three axial directions is conducted to examine stress transfer to the nearest neighbor and assess scale-up stress transfer. Our findings reveal that hybrid lattice structure unit cells exhibit significantly improved modulus in the range of 125% to 393%, specific modulus in the range of 13% to 120%, and energy absorption in the range of 17% to 395% over the open lattice. The scaled-up lattice modulus increased by 8% to 400%, specific modulus by 2% to 107%, and energy absorption by 37% to 553% over the lattice frame. Parameters that emerged as key to improved lightweighting.

FDM↗
NASA NTRS2026

Thermal Performance of Common Bulk-Fill Cryogenic Insulation Materials in Helium and Hydrogen Background Gases

Maritime shipping of vast quantities of liquid hydrogen (LH 2 ) will be necessary to facilitate a global hydrogen ecosystem; with some studies estimating volumes up to 172,000 m 3 for individual tanker ships, and requiring stationary storage tanks at terminals of 50,000 m 3 to 100,000 m 3 —ten to fifteen times larger than the current largest tank, located at launch pad B at NASA Kennedy Space Center (KSC). Such a radical scale-up will push the boundary of traditional, vacuum-insulated tank designs. Hence, a potential need exists for non-vacuum solutions, which necessitates exploring the thermal performance of insulation materials in non-condensable background gasses at LH 2 temperatures, namely helium and hydrogen. Testing of two bulk-fill insulation materials common to large LH 2 storage tanks, perlite and glass bubbles, in helium and hydrogen was recently conducted by the Cryogenics Test Laboratory at KSC using the Cryostat-100 liquid nitrogen boiloff calorimeter per the ASTM C1774 standard methodology. Effective thermal conductivity (k e ) and heat flux (q) results for each insulation/gas combination are presented across the full vacuum range, as well as thermal profiles through the insulation thickness between 78 K and 293 K.

A M Swanger↗