Search NASA⌕ Search

SEARCH · Search NASA

Results for “See and Avoid”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The Active Optics System on the Vera C. Rubin Observatory: Optimal Control of Degeneracy among the Large Number of Degrees of Freedom

Abstract The Vera C. Rubin Observatory is a unique facility for survey astronomy that will soon be commissioned and begin operations. Crucial to many of its scientific goals is the achievement of sustained high image quality, limited only by the seeing at the site. This will be maintained through an active optics system that controls optical element misalignments and corrects mirror figure error to minimize aberrations caused by both thermal and gravitational effects. However, the large number of adjustment degrees of freedom available on the Rubin Observatory introduces a range of degeneracies, including many that are induced by noise due to imperfect measurement of the wave-front errors. We present a structured methodology for identifying these degeneracies through an analysis of image noise level. We also present a novel scaling strategy based on truncated singular value decomposition that mitigates the degeneracy and optimally distributes the adjustment over the available degrees of freedom. Our approach ensures the attainment of optimal image quality, while avoiding excursions around the noise-induced subspace of degeneracies, marking a significant improvement over the previous techniques adopted for Rubin, which were based on an optimal integral controller. This new approach is likely to also yield significant benefits for all telescopes that incorporate large numbers of degrees of freedom of adjustment.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2016

Enabling Affordable Communications for the Burgeoning Deep Space Cubesat Fleet

The low costs of development and launch, coupled with new propulsive technologies, have made CubeSats increasingly popular for use in science investigations beyond geosynchronous orbit. As this deep space CubeSat fleet grows in size, the challenge of trying to provide affordable communications for it grows commensurately. The mass, power, and volume constraints inherent to CubeSats limit the antenna size and transmit power that they can use to close the deep space link. As a consequence, CubeSats need to rely more heavily on ground antennas that are characterized by large aperture, low noise temperatures, and relatively high-power transmitters. Such antennas are not in great abundance, nor are they inexpensive to build. For this reason, NASA’s Deep Space Network has been advocating a three-pronged approach to meeting anticipated CubeSat demand: development of simultaneous, shared-beam multi-spacecraft communications capabilities, development of large-antenna cross-support arrangements with other agencies and universities, and development of less uplink-intensive navigation techniques. This paper focuses on the pursuit of simultaneous, shared-beam multi-spacecraft communications capabilities. While the Multiple Spacecraft per Antenna (MSPA) technique has existed for over a decade, it has generally been limited to supporting downlink for just two in-beam spacecraft at a time. This limitation has largely been a function of the number and cost of available receivers. A relatively new technique that potentially overcomes this limitation is Opportunistic MSPA (OMSPA). Instead of relying on additional receivers, OMSPA makes use of a digital recorder at each ground station that is capable of capturing the intermediate frequency (IF) signals from every spacecraft in the antenna beam within the frequency bands of interest. When CubeSat projects see one or more opportunities for their CubeSat(s) to intercept the traditionally scheduled antenna beam of a “host” spacecraft, they can arrange for the CubeSat(s) to transmit open loop during those opportunities. Via a secure Internet site, the CubeSat mission operators can then retrieve the time- and frequency-relevant portions of the digital recording for subsequent demodulation and decoding, or subscribe to a service that does it for them. This “opportunistic” use of a host spacecraft’s ground antenna beam potentially enables CubeSat projects to make use of large ground antennas for downlink without having to compete with bigger, better-funded missions for antenna time in the formal scheduling process. In so doing, it also potentially enables CubeSat projects to avoid the aperture fees associated with formally scheduled downlink time - fees that factor into the “bottom-line” of competitively-bid NASA missions and that actually get charged to non-NASA missions. Taking advantage of these potential OMSPA benefits, however, will require CubeSat projects to pursue mission designs that ensure at least periodic in-beam operations relative to a “host” spacecraft. In the case of a constellation of CubeSats with inter-spacecraft distances that do not extend outside of the beam-width of the desired ground antenna at the given range, one CubeSat can serve as the “host” and have a formally scheduled downlink while the rest of the CubeSats can downlink essentially for “free” via OMSPA. Deep space CubeSats, of course, will need uplink in addition to downlink. Beyond commanding, this need is driven by the use of two-way ranging and Doppler for navigation. While OMSPA may not directly facilitate uplink, it does have the potential to free up antennas for those spacecraft that periodically require formally scheduled links for commanding and two-way radio metrics. NASA is also exploring the physical feasibility of an in-beam, simultaneous multi-spacecraft uplink technique. As with OMSPA, if successful, it will require little new equipment, further enabling affordable deep space CubeSat communications.

Abraham, Douglas S.↗
NASA NTRS2010

Accelerated Aging System for Prognostics of Power Semiconductor Devices

Prognostics is an engineering discipline that focuses on estimation of the health state of a component and the prediction of its remaining useful life (RUL) before failure. Health state estimation is based on actual conditions and it is fundamental for the prediction of RUL under anticipated future usage. Failure of electronic devices is of great concern as future aircraft will see an increase of electronics to drive and control safety-critical equipment throughout the aircraft. Therefore, development of prognostics solutions for electronics is of key importance. This paper presents an accelerated aging system for gate-controlled power transistors. This system allows for the understanding of the effects of failure mechanisms, and the identification of leading indicators of failure which are essential in the development of physics-based degradation models and RUL prediction. In particular, this system isolates electrical overstress from thermal overstress. Also, this system allows for a precise control of internal temperatures, enabling the exploration of intrinsic failure mechanisms not related to the device packaging. By controlling the temperature within safe operation levels of the device, accelerated aging is induced by electrical overstress only, avoiding the generation of thermal cycles. The temperature is controlled by active thermal-electric units. Several electrical and thermal signals are measured in-situ and recorded for further analysis in the identification of leading indicators of failures. This system, therefore, provides a unique capability in the exploration of different failure mechanisms and the identification of precursors of failure that can be used to provide a health management solution for electronic devices.

Celaya, Jose R.↗
DOE OSTI2020

Preliminary parameter studies to form pellets of hard materials for optical constants derived via single-angle reflectance spectroscopy

Infrared reflectance spectra can be influenced by many factors: the substrate and the thickness of the layer for liquids and the surface micromorphology, the form (powder, crystal) and the particle size for solids. All these parameters can play a role in the appearance of the measured spectrum. To avoid collecting multitudes of spectra to cover all such scenarios, the optical constants n and k, which are intrinsic properties of a material, can instead be used to model the reflectance spectrum. For solids, two techniques are often used to derive optical constants: ellipsometry and single-angle reflectance spectroscopy. For both methods, best results are usually obtained from single crystals. We have recently demonstrated for ammonium sulfate (a relatively soft material) that by optimizing certain conditions, high quality pellets with specularly reflective surfaces can be used in lieu of crystals. This was confirmed by the excellent agreement between the optical constants derived by these two methods. This work focuses on the possible extension of these methods to harder materials, starting with sodium sulfate. The first goal is to see if high quality pellet surfaces can be obtained as for ammonium sulfate. The reflectance values and the associated optical constants can also be obtained.

Diaz, Emmanuela↗
DOE OSTI2023

Long-run Marginal Emission Rates for Electricity - Workbooks for 2022 Cambium Data

These workbooks contain modeled estimates of long-run marginal emission rates (LRMER) for the contiguous United States. A LRMER is an estimate of the rate of emissions that would be either induced or avoided by a change in electric demand, taking into account how the change could influence both the operation as well as the structure of the grid (i.e., the building and retiring of capital assets, such as generators and transmission lines). It is therefore distinct from the more-commonly-known short-run marginal, which treat grid assets as fixed. Long-run marginal emissions rates are generally appropriate to use when trying to comprehensively estimate the impact of a long-lived (i.e., more than several years) intervention. There are two workbooks that supply the data at two different geographic resolutions: states and GEA regions (20 regions that are similar to, but not exactly the same as, the US EPA's eGRID regions). For more data underlying these emissions factors, see the Cambium 2022 project at https://scenarioviewer.nrel.gov/. For more details on input assumptions and methodology see the associated report (Cambium 2022 Scenario Descriptions and Documentation, https://www.nrel.gov/docs/fy23osti/84916.pdf). This data is planned to be updated annually. Information on the latest versions can be found at https://www.nrel.gov/analysis/cambium.html.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Characterization of elastic mechanical properties of Tuscaloosa Marine Shale from well logs using the vertical transversely isotropic model

To avoid steep declines in the Tuscaloosa Marine Shale (TMS) production, wells are fracture-stimulated to release the hydrocarbons trapped in the matrix of the formation. An accurate estimation of Young’s modulus and Poisson’s ratio is essential for hydraulic fracture propagation. In addition, ignoring the highly heterogeneous and anisotropic character of TMS can lead to erroneous stress values, which subsequently affect hydraulic fracture width estimates and the overall hydraulic fracturing process. We have developed an empirical 1D geomechanical model that takes into account VTI anisotropy, and it is used to characterize the elastic mechanical properties of TMS in two wells. In the analyzed formation, the vertical Poisson’s ratio is less than the horizontal Poisson’s ratio, which suggests the necessity of an alternative to the ANNIE equations. The stiffness coefficients [Formula: see text] and [Formula: see text] were estimated using the relationships developed from the ultrasonic core data available for the two TMS. Further, correlations between the static and dynamic properties from laboratory tests were used to improve the minimum horizontal stress calculation. We compare VTI Young’s moduli, Poisson’s ratios, and minimum horizontal stress with the isotropic solution. VTI modeling improves the estimation of the elastic mechanical properties. The isotropic solution underestimates the minimum horizontal stress in the formation. Moreover, it was shown that the 20 ft shale interval below the TMS base is characterized by a low Young’s modulus (the vertical Young’s modulus is equal to 20 GPa, whereas the horizontal Young’s modulus is equal to 40 GPa) and may be a frac barrier.

Geochemistry & Geophysics↗
NASA NTRS2012

I-FORCAST: Rapid Flight Planning Tool

I-FORCAST (Instrument - Field of Regard Coverage Analysis and Simulation Tool) is a flight planning tool specifically designed for quickly verifying the feasibility and estimating the cost of airborne remote sensing campaigns (see figure). Flights are simulated by being broken into three predefined routing algorithms as necessary: mapping in a snaking pattern, mapping the area around a point target (like a volcano) with a star pattern, and mapping the area between a list of points. The tool has been used to plan missions for radar, lidar, and in-situ atmospheric measuring instruments for a variety of aircraft. It has also been used for global and regional scale campaigns and automatically includes landings when refueling is required. The software has been compared to the flight times of known commercial aircraft route travel times, as well as a UAVSAR (Uninhabited Aerial Vehicle Synthetic Aperture Radar) campaign, and was within 15% of the actual flight time. Most of the discrepancy is due to non-optimal flight paths taken by actual aircraft to avoid restricted airspace and used to follow landing and take-off corridors.

Oaida, Bogdan↗
NASA NTRS2024

Hopkinson Bar Impact Force Measurement for Application to Development of an Artificial Bird

A test method has been published for measuring forces from bird cadavers and artificial birds to demonstrate equivalency to support the use of artificial birds in aircraft certification testing. The test method involves a large diameter Hopkinson bar as the technique for measuring and comparing forces. The method involves the assumption that a force on one end of the bar results in a one-dimensional plane wave that travels down the bar. To avoid reflected waves from the end of the bar overlapping the input pulse, and due to practical limitations on the length of the bar, strain transducers are located relatively close to the impacted face of the bar, raising questions about the validity of the assumption of one-dimensional wave propagation. In addition, the large diameter of the bar can introduce dispersion effects in the propagated pulse. These must be assessed to determine the impact on the accuracy of impact force measurements and, if significant, dispersion correction techniques must be used. In this study analytical, experimental, and computational methods are used to analyze the wave propagation characteristics for impact forces expected from realistic bird impacts. While wave dispersion and effects of non-concentric impacts are present, the resulting errors are relatively small. For the response we expect to see in bird impacts up to velocities of approximately 300 m/sec the large diameter Hopkinson bar test appears to be an acceptable method for measuring the impact forces and comparing the response of real and proposed artificial birds.

Birdstrike↗
NASA NTRS2018

Stabilized Approach Criteria: Bridging the Gap Between Theory and Practice

Approach and landing is the most common phase of flight for aviation accidents, accounting annually for approximately 65 percent of all accidents. A Flight Safety Foundation study of 16 years of runway excursions determined that 83 percent could have been avoided with a decision to go around. In other words, 54 percent of all accidents could potentially be prevented by going around. A critical industry policy designed to help prevent such accidents is the go-around policy. However, the collective industry performance of complying with go-around policies is extremely poor and only about three percent of unstable approaches result in a go-around. Improving the go-around compliance rate holds tremendous potential in reducing approach and landing accidents. There are many reasons for flight crews ignoring go-around policies related to pilot judgement and company policies. Examples are the collective industry norm to accept the noncompliance of go-around policies, management being disengaged from go-around noncompliance, and pilot fatigue and lack of situational awareness. One of the biggest factors is that pilots see current stabilized-approach criteria as too complex and restrictive for the operational environment. Following the American Airlines 1420 accident (Little Rock, 1999), where the aircraft overran the runway upon landing and crashed, the National Transportation Safety Board (NTSB) recommended that the Federal Aviation Administration (FAA) define detailed parameters for a stabilized approach, and develop detailed criteria indicating when a go-around should be performed. The experiment discussed in this presentation is the first step towards developing these go-around criteria for commercial transport aircraft.

pilot performance↗
NASA NTRS2017

Kepler Commissioning Data for Measurement of the Pixel Response Function and Focal Plane Geometry

This document describes the Kepler PRF/FPG data release. This data was taken on April 27-29, 2009, during Kepler's commissioning phase in order to measure the pixel response function (PRF) (Bryson et al., 2010a) and focal plane geometry (FPG) (Tenenbaum and Jenkins, 2010). 33,424 stellar targets were observed for 243 long cadences, each with a duration of 14.7 minutes (half the duration of a normal Kepler long cadence). During these 243 cadences the Kepler photometer was moved, pointing in a dither pattern to facilitate PRF measurement. Motion occurred during the even cadences (second, fourth, etc.), with the telescope in stable fine point at each pointing in the dither pattern during the odd cadences (first, third, etc.). The first and last cadences were at the center of the dither pattern. Motion cadences are included in this release, but they do not contain any data. For details on how this data was used to derive the Kepler PRF and FPG models, see Bryson et al. (2010a) and Tenenbaum and Jenkins (2010). Descriptions of the PRF and FPG models are found in Thompson et al. (2016), x2.3.5.17 and x2.3.5.16 respectively. The data in this release can be used to recompute the Kepler PRF and FPG. Such a reconstruction, however, would not reflect measured seasonal changes in the PRF described in Van Cleve et al. (2016b), x5.2.The dither pattern is shown in Figure 1. The crosses show the commanded pointings and the circles show the measured pointings. Measured pointings are different from the commanded pointings due to the early state of calibration of the fine guidance sensors during commissioning (Van Cleve et al., 2016a). The measured offsets from the center of the pattern are given in RADEC offsets and pixel offsets in Table 1. The order of the offsets was randomized during data collection to avoid time-dependent systematics.

Kepler↗
NASA NTRS2005

Dynamic wake prediction and visualization with uncertainty analysis

A dynamic wake avoidance system utilizes aircraft and atmospheric parameters readily available in flight to model and predict airborne wake vortices in real time. A novel combination of algorithms allows for a relatively simple yet robust wake model to be constructed based on information extracted from a broadcast. The system predicts the location and movement of the wake based on the nominal wake model and correspondingly performs an uncertainty analysis on the wake model to determine a wake hazard zone (no fly zone), which comprises a plurality of wake planes, each moving independently from another. The system selectively adjusts dimensions of each wake plane to minimize spatial and temporal uncertainty, thereby ensuring that the actual wake is within the wake hazard zone. The predicted wake hazard zone is communicated in real time directly to a user via a realistic visual representation. In an example, the wake hazard zone is visualized on a 3-D flight deck display to enable a pilot to visualize or see a neighboring aircraft as well as its wake. The system substantially enhances the pilot's situational awareness and allows for a further safe decrease in spacing, which could alleviate airport and airspace congestion.

Holforty, Wendy L.↗
DOE OSTI2024

Local primordial non-Gaussianity from the large-scale clustering of photometric DESI luminous red galaxies

ABSTRACT We use angular clustering of luminous red galaxies from the Dark Energy Spectroscopic Instrument (DESI) imaging surveys to constrain the local primordial non-Gaussianity parameter fNL. Our sample comprises over 12 million targets, covering 14 000 deg2 of the sky, with redshifts in the range 0.2 < z < 1.35. We identify Galactic extinction, survey depth, and astronomical seeing as the primary sources of systematic error, and employ linear regression and artificial neural networks to alleviate non-cosmological excess clustering on large scales. Our methods are tested against simulations with and without fNL and systematics, showing superior performance of the neural network treatment. The neural network with a set of nine imaging property maps passes our systematic null test criteria, and is chosen as the fiducial treatment. Assuming the universality relation, we find $f_{\rm NL} = 34^{+24(+50)}_{-44(-73)}$ at 68 per cent (95 per cent) confidence. We apply a series of robustness tests (e.g. cuts on imaging, declination, or scales used) that show consistency in the obtained constraints. We study how the regression method biases the measured angular power spectrum and degrades the fNL constraining power. The use of the nine maps more than doubles the uncertainty compared to using only the three primary maps in the regression. Our results thus motivate the development of more efficient methods that avoid overcorrection, protect large-scale clustering information, and preserve constraining power. Additionally, our results encourage further studies of fNL with DESI spectroscopic samples, where the inclusion of 3D clustering modes should help separate imaging systematics and lessen the degradation in the fNL uncertainty.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2016

Simulation Development and Analysis of Crew Vehicle Ascent Abort

NASA's Commercial Crew Program is an integral step in its journey to Mars as it would expedite development of space technologies and open up partnership with U.S. commercial companies. NASA reviews and independent assessment of Commercial Crew Program is fundamental to its success, and being able to model a commercial crew vehicle in a simulation rather than conduct a live test would be a safer, faster, and less expensive way to assess and certify the capabilities of the vehicle. To this end, my project was to determine the feasibility of using a simulation tool named SOMBAT version 2.0 to model a multiple parachute system for Commercial Crew Program simulation. The main tasks assigned to me were to debug and test the main parachute system model, (capable of simulating one to four main parachute bodies), and to utilize a graphical program to animate the simulation results. To begin tackling the first task, I learned how to use SOMBAT by familiarizing myself with its mechanics and by understanding the methods used to tweak its various parameters and outputs. I then used this new knowledge to set up, run, and analyze many different situations within SOMBAT in order to explore the limitations of the parachute model. Some examples of parameters that I varied include the initial velocity and orientation of the falling capsule, the number of main parachutes, and the location where the parachutes were attached to the capsule. Each parameter changed would give a different output, and in some cases, would expose a bug or limitation in the model. A major bug that I discovered was the inability of the model to handle any number of parachutes other than three. I spent quite some time trying to debug the code logically, but was unable to figure it out until my mentor taught me that digital simulation limitations can occur when some approximations are mistakenly assumed for certain in a physical system. This led me to the realization that unlike in all of the programming classes I have taken thus far that focus on pure logic, simulation code focuses on mimicking the physical world with some approximation and can have inaccuracies or numerical instabilities. Learning from my mistake, I adopted new methods to analyze these different simulations. One method the student used was to numerically plot various physical parameters using MATLAB to confirm the mechanical behavior of the system in addition to comparing the data to the output from a separate simulation tool called FAST. By having full control over what was being outputted from the simulation, I could choose which parameters to change and to plot as well as how to plot them, allowing for an in depth analysis of the data. Another method of analysis was to convert the output data into a graphical animation. Unlike the numerical plots, where all of the physical components were displayed separately, this graphical display allows for a combined look at the simulation output that makes it much easier for one to see the physical behavior of the model. The process for converting SOMBAT output for EDGE graphical display had to be developed. With some guidance from other EDGE users, I developed a process and created a script that would easily allow one to display simulations graphically. Another limitation with the SOMBAT model was the inability for the capsule to have the main parachutes instantly deployed with a large angle between the air speed vector and the chutes drag vector. To explore this problem, I had to learn about different coordinate frames used in Guidance, Navigation & Control (J2000, ECEF, ENU, etc.) to describe the motion of a vehicle and about Euler angles (e.g. Roll, Pitch, Yaw) to describe the orientation of the vehicle. With a thorough explanation from my mentor about the description of each coordinate frame, as well as how to use a directional cosine matrix to transform one frame to another, I investigated the problem by simulating different capsule orientations. In the end, I was able to show that this limitation could be avoided if the capsule is initially oriented antiparallel to its velocity vector.

Wong, Chi S.↗
DOE OSTI2021

Interactive Mesh Generation and Comparison Tools for Nuclear Energy Advanced Modeling & Simulation Phase I. Final Report

The promise of computer simulations for nuclear reactor designs is the opportunity to speed up the design process while also improving safety, providing more detail and higher fidelity, reducing cost, minimizing schedule risk, and avoiding many other potential problems; because simulations have the potential to be much less expensive and time-consuming than traditional development – where scale models and physical tests require construction and long lead times – it is possible to consider more alternatives and complete more comprehensive assessments before the design is finalized and constructed. As more design scenarios are studied by simulation, the speed that simulations promise is only available as long as bottlenecks are addressed for these scenarios. A frequent bottleneck is the amount of human labor required to describe the shape of the objects being designed and decompose the shape into simple elements, such as hexahedra, that are small enough to capture the physical phenomena of interest without being so small that even fast computers cannot perform the simulation in a reasonable amount of time. Recently, techniques for creating all-hexahedral decompositions have been developed, but they require some human input. Many simulation codes prefer all-hexahedral decompositions, so we proposed to evaluate the feasibility of these techniques on nuclear reactor geometries to see whether they required too much human input to be commercially viable. Our study concluded that they can be made viable with some additional software tools to reduce the amount of user input required.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Summary Report of the Reactive CO 2 Capture: Process Integration for the New Carbon Economy Workshop

Decarbonization of our global economy is required to limit planetary warming to +1.5⁰C above pre-industrial levels, an ambitious goal set into motion by the Paris agreement. Given the scale and urgency, the solution demands international, cross-sector advancements spanning policy, social responsibility, and technology, with emphasis on step changes over incremental changes. To that end, technological revolutions that disrupt the status quo need to be envisioned and enacted. One potential technological revolution is the production of fuels, chemicals, and materials from carbon dioxide (CO 2 ) as the starting feedstock, leveraging renewable energy as the driving force. Over the past decades, significant research, development, and deployment has occurred on technologies for capturing CO 2 from point sources or the air and utilizing this CO 2 as a working fluid or as a chemical reactant; however, most of this work has been siloed in these two categories. Recently, an emerging field has started to explore the direct integration of CO 2 capture and conversion technologies as a means to reduce overall energy demand (i.e., avoid energy penalty of CO 2 desorption/regeneration of capture media) and capital expense through process intensification. This strategy represents an opportunity to leapfrog forward this technological revolution. However, the field is in its infancy and the technologies are at an early stage of development, thus it is critically important to define and assess the value proposition of this strategy relative to alternatives (e.g., separated capture and conversion technologies, fuels and chemicals derived from renewable feedstocks like biomass, and industrial electrification) to chart a path forward. To identify next steps, we organized a workshop titled “Reactive CO 2 Capture: Process Integration for the New Carbon Economy” which was held in Golden, Colorado, February 18–19, 2020. The focus of this workshop was to discuss approaches for merging CO 2 capture and CO 2 conversion/utilization systems into what we denoted as an integrated "reactive capture" strategy. By our definition, reactive capture of CO 2 is the coupled process of capturing CO 2 from a mixed gas stream and converting it into a valuable product without going through a purified CO 2 intermediate (see full definition in the Introduction section). This report seeks to summarize feedback from the approximately 125 participants and subject matter experts in attendance from academia, industry, U.S. Department of Energy (DOE), and DOE national laboratories. The workshop agenda is included in Appendix A and the full list of attendees can be found in Appendix B. To elucidate a path forward, we first asked the attendees to define what success would look like for reactive capture in the short term (0–5 years), midterm (5–10 years), and long term (10+ years) and then asked them to answer four questions related to how we could achieve that success: (1) What are the key barriers and challenges to success? (2) What are needed activities to overcome barriers and challenges? (3) What opportunities will arise from these activities? (4) What is a target outcome and what metrics need to be met?

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS2016

The UK Met Office GCM with a Sophisticated Radiation Scheme Applied to the Hot Jupiter HD 209458b

To study the complexity of hot Jupiter atmospheres revealed by observations of increasing quality, we have adapted the UK Met Office Global Circulation Model (GCM), the Unified Model (UM), to these exoplanets. The UM solves the full 3D Navier-Stokes equations with a height-varying gravity, avoiding the simplifications used in most GCMs currently applied to exoplanets. In this work we present the coupling of the UM dynamical core to an accurate radiation scheme based on the two-stream approximation and correlated-k method with state-of-the-art opacities from ExoMol. Our first application of this model is devoted to the extensively studied hot Jupiter HD 209458b. We derive synthetic emission spectra and phase curves, and compare them to both previous models also based on state-of-the-art radiative transfer, and to observations. We find a reasonable a agreement between observations and both our days side emission and hot spot offset, however, our night side emissions is too large. Overall our results are qualitatively similar to those found by Showman et al. (2009) with the SPARCMIT gcm, however, we note several quantitative differences: Our simulations show significant variation in the position of the hottest part of the atmosphere with pressure, as expected from simple timescale arguments, and in contrast to the vertical coherency found by Showman et al. (2009). We also see significant quantitative differences in calculated synthetic observations. Our comparisons strengthen the need for detailed intercomparisons of dynamical cores, radiation schemes and post-processing tools to understand these differences. This effort is necessary in order to make robust conclusions about these atmospheres based on GCM results.

radiation↗
NASA NTRS1998

A Survey of Applications and Research in Integrated Design Systems Technology

The initial part of the study was begun with a combination of literature searches, World Wide Web searches, and contacts with individuals and companies who were known to members of our team to have an interest in topics that seemed to be related to our study. There is a long list of such topics, such as concurrent engineering, design for manufacture, life-cycle engineering, systems engineering, systems integration, systems design, design systems, integrated product and process approaches, enterprise integration, integrated product realization, and similar terms. These all capture, at least in part, the flavor of what we describe here as integrated design systems. An inhibiting factor in this inquiry was the absence of agreed terminology for the study of integrated design systems. It is common for the term to be applied to what are essentially augmented Computer-Aided Design (CAD) systems, which are integrated only to the extent that agreements have been reached to attach proprietary extensions to proprietary CAD programs. It is also common for some to use the term integrated design systems to mean a system that applies only, or mainly, to the design phase of a product life cycle. It is likewise common for many of the terms listed earlier to be used as synonyms for integrated design systems. We tried to avoid this ambiguity by adopting the definition of integrated design systems that is implied in the introductory notes that we provided to our contacts, cited earlier. We thus arrived at this definition: Integrated Design Systems refers to the integration of the different tools and processes that comprise the engineering, of complex systems. It takes a broad view of the engineering of systems, to include consideration of the entire product realization process and the product life cycle. An important aspect of integrated design systems is the extent to which they integrate existing, "islands of automation" into a comprehensive design and product realization environment. As the study progressed, we relied increasingly upon a networking approach to lead us to new information. The departure point for such searches often was a government-sponsored project or a company initiative. The advantage of this approach was that short conversations with knowledgeable persons would usually cut through confusion over differences of terminology, thereby somewhat reducing the search space of the study. Even so, it was not until late in our eight-month inquiry that we began to see signs of convergence of the search, in the sense that a number of the latest inquiries began to turn up references to earlier contacts. As suggested above, this convergence often occurred with respect to particular government or company projects.

Source record↗