Search NASA⌕ Search

SEARCH · Search NASA

Results for “Speed Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Evaluation of a Tool for Airborne-Managed In-Trail Approach Spacing

The Advanced Terminal Area Approach Spacing (ATAAS) tool uses Automatic Dependent Surveillance-Broadcast aircraft state data to compute a speed command for an ATAAS-equipped aircraft to follow and obtain a required time interval behind another aircraft. The ATAAS tool and candidate operational procedures were tested in a high-fidelity, full mission simulator with active airline subject pilots flying an arrival scenario to obtain pilot perceptions of acceptability and workload for the concept. The aircraft consistently achieved the target spacing interval within 1 s when the ATAAS speed guidance was autothrottle-coupled and a slightly greater (4 - 5 s) but consistent interval with pilot-controlled speed changes. The subject pilots rated the ATAAS workload as similar to one with standard procedures for a nominal Instrument Landing System (ILS) approach. They also rated highly various procedural aspects (including amount of head-down time required). Eyetracker data showed only slight changes in instrument scan patterns for ATAAS versus standard ILS procedures.

Oseguera-Lohr, Rosa M.↗

Space Shuttle autoland design

The Orbiter Autoland system is activated at 10,000 ft altitude and performs energy control through speedbrake modulation, vertical path tracking with acceleration commands to the pitch control system, lateral path tracking through bank angle commands to the roll control system, and brings the vehicle to main gear touchdown. A nominal 19 degree glide slope is flown down to 2000 ft, followed by a 1.5 deg path to flare and subsequent soft landing. The flight path is similar to that which a pilot would fly, a feature which increases safety factors should manual takeover be necessary during landing maneuvers. A block diagram of the autoland control interfaces is provided, and attention is given to the use of a reference trajectory, the guidance laws, lateral guidance, the speed control system, pitch rate control, and the rollout system. Conditions and instrument indications leading to pilot takeover are outlined.

Tsikalas, G. M.↗

Learning to train neural networks for real-world control problems

Over the past three years, our group has concentrated on the application of neural network methods to the training of controllers for real-world systems. This presentation describes our approach, surveys what we have found to be important, mentions some contributions to the field, and shows some representative results. Topics discussed include: (1) executing model studies as rehearsal for experimental studies; (2) the importance of correct derivatives; (3) effective training with second-order (DEKF) methods; (4) the efficacy of time-lagged recurrent networks; (5) liberation from the tyranny of the control cycle using asynchronous truncated backpropagation through time; and (6) multistream training for robustness. Results from model studies of automotive idle speed control serve as examples for several of these topics.

Feldkamp, Lee A.↗

A Modular Aero-Propulsion System Simulation of a Large Commercial Aircraft Engine

A simulation of a commercial engine has been developed in a graphical environment to meet the increasing need across the controls and health management community for a common research and development platform. This paper describes the Commercial Modular Aero Propulsion System Simulation (C-MAPSS), which is representative of a 90,000-lb thrust class two spool, high bypass ratio commercial turbofan engine. A control law resembling the state-of-the-art on board modern aircraft engines is included, consisting of a fan-speed control loop supplemented by relevant engine limit protection regulator loops. The objective of this paper is to provide a top-down overview of the complete engine simulation package.

DeCastro, Jonathan A.↗

Performance verification and system parameter identification of spacecraft tape recorder control servo

Design adequacy of the lead-lag compensator of the frequency loop, accuracy checking of the analytical expression for the electrical motor transfer function, and performance evaluation of the speed control servo of the digital tape recorder used on-board the 1976 Viking Mars Orbiters and Voyager 1977 Jupiter-Saturn flyby spacecraft are analyzed. The transfer functions of the most important parts of a simplified frequency loop used for test simulation are described and ten simulation cases are reported. The first four of these cases illustrate the method of selecting the most suitable transfer function for the hysteresis synchronous motor, while the rest verify and determine the servo performance parameters and alternative servo compensation schemes. It is concluded that the linear methods provide a starting point for the final verification/refinement of servo design by nonlinear time response simulation and that the variation of the parameters of the static/dynamic Coulomb friction is as expected in a long-life space mission environment.

Mukhopadhyay, A. K.↗

ISS Double-Gimbaled CMG Subsystem Simulation Using the Agile Development Method

This paper presents an evolutionary approach in simulating a cluster of 4 Control Moment Gyros (CMG) on the International Space Station (ISS) using a common sense approach (the agile development method) for concurrent mathematical modeling and simulation of the CMG subsystem. This simulation is part of Training systems for the 21st Century simulator which will provide training for crew members, instructors, and flight controllers. The basic idea of how the CMGs on the space station are used for its non-propulsive attitude control is briefly explained to set up the context for simulating a CMG subsystem. Next different reference frames and the detailed equations of motion (EOM) for multiple double-gimbal variable-speed control moment gyroscopes (DGVs) are presented. Fixing some of the terms in the EOM becomes the special case EOM for ISS's double-gimbaled fixed speed CMGs. CMG simulation development using the agile development method is presented in which customer's requirements and solutions evolve through iterative analysis, design, coding, unit testing and acceptance testing. At the end of the iteration a set of features implemented in that iteration are demonstrated to the flight controllers thus creating a short feedback loop and helping in creating adaptive development cycles. The unified modeling language (UML) tool is used in illustrating the user stories, class designs and sequence diagrams. This incremental development approach of mathematical modeling and simulating the CMG subsystem involved the development team and the customer early on, thus improving the quality of the working CMG system in each iteration and helping the team to accurately predict the cost, schedule and delivery of the software.

Inampudi, Ravi↗

Perpetual factors involved in performance of air traffic controllers using a microwave landing system

The task involved the control of two simulated aircraft targets per trial, in a 37.0 -km radius terminal area, by means of conventional radar vectoring and/or speed control. The goal was to insure that the two targets crossed the Missed Approach Point (MAP) at the runway threshold exactly 60 sec apart. The effects on controller performance of the MLS configuration under wind and no-wind conditions were examined. The data for mean separation time between targets at the MAP and the range about that mean were analyzed by appropriate analyses of variance. Significant effects were found for mean separation times as a result of the configuration of the MLS and for interaction between the configuration and wind conditions. The analysis of variance for range indicated significantly poorer performance under the wind condition. These findings are believed to be a result of certain perceptual factors involved in radar air traffic control (ATC) using the MLS with separation of targets in time.

Gershzohn, G.↗

Spacelab high density digital recorders

The design and performance of the high-density digital recorder (HDDR) developed for use at the NASA centers (KSC, JSC, and GSFC) and at the JPL to store and retrieve 50-Mb/s PCM data streams from the Spacelab experiments are reported. The recording reproduction, and transport requirements are reviewed; and the design solutions adopted in the final version of the HDDR are described, incuding three-position-modulation and Y-phase encoding, microprocessor-controlled automatic bit synchronization and equalization, cyclic-redundancy-check error detection and correction, clock regeneration, data and clock variations, tape-speed control, and EEE-488 remote control. Reliable performance, with bit error rates 1 in 10 to the 10th forward and 1 in 10 to the 9th reverse or better and packing density up to 50 percent greater than that obtainable using conventional codes, is reported after 1.5 years of service.

Blais, R. A.↗

Pitch attitude, flight path, and airspeed control during approach and landing of a powered lift STOL aircraft

Analytical investigations and piloted moving base simulator evaluations were conducted for manual control of pitch attitude, flight path, and airspeed for the approach and landing of a powered lift jet STOL aircraft. Flight path and speed response characteristics were described analytically and were evaluated for the simulation experiments which were carried out on a large motion simulator. The response characteristics were selected and evaluated for a specified path and speed control technique. These charcteristics were: (1) the initial pitch response and steady pitch rate sensitivity for control of attitude with a pitch rate command/ attitude hold system, (2) the initial flight path response, flight path overshoot, and flight path-airspeed coupling in response to a change in thrust, and (3) the sensitivity of airspeed to pitch attitude changes. Results are presented in the form of pilot opinion ratings and commentary, substantiated where appropriate by response time histories and aircraft states at the point of touchdown.

Franklin, J. A.↗

Fluidics research, including vortex and jet pipe valves

The research at the Systems and Control Laboratory is reported. Topics discussed include: response characteristics of laminar fluidic amplifiers, power amplification with a vortex valve, pulse-supply-mode fluidics, speed control system employing a jet pipe valve, and the fluidics reference center.

Source record↗

Development and flight test results of an autothrottle control system at Mach 3 cruise

Flight test results obtained with the original Mach hold autopilot designed the YF-12C airplane which uses elevator control and a newly developed Mach hold system having an autothrottle integrated with an altitude hold autopilot system are presented. The autothrottle tests demonstrate good speed control at high Mach numbers and high altitudes while simultaneously maintaining control over altitude and good ride qualities. The autothrottle system was designed to control either Mach number or knots equivalent airspeed (KEAS). Excellent control of Mach number or KEAS was obtained with the autothrottle system when combined with altitude hold. Ride qualities were significantly better than with the conventional Mach hold system.

Gilyard, G. B.↗

Alternating-Current Motor Drive for Electric Vehicles

New electric drive controls speed of a polyphase as motor by varying frequency of inverter output. Closed-loop current-sensing circuit automatically adjusts frequency of voltage-controlled oscillator that controls inverter frequency, to limit starting and accelerating surges. Efficient inverter and ac motor would give electric vehicles extra miles per battery charge.

Krauthamer, S.↗

Performance effects of plan-based displays in commercial aviation

The experiment reported here examines the performance consequences of alignment between display formats and the methods used during descent. Twelve commercial pilots flew one of nine Standard Terminal Arrival Routes on a stand-alone flight simulator run on a Sparc II workstation. Three different methods for descent (Manual Control, Autopilot and Spoilers) were crossed with three methods according to scope, resolution, and bandwidth properties in the display of critical information. Performance variability in speed control supports our claim that the effectiveness of a display is not an independent property of the display itself, but rather, a function of the interaction of the display and the particular methods used for achieving task goals.

Shalin, Valerie L.↗

Pilot's manual for automated 4D guidance system

Operational procedures and modes of an experimental 4D guidance system are described from the pilot's point of view. The system consists of the experimental avionics equipment referred to as STOLAND and a specially developed software package for the STOLAND digital computer. A capture mode of the system provides arrival time control and automatic tracking of the 4D flight path from any feasible initial aircraft state to any waypoint. Precise arrival time at a waypoint is achieved by means of speed control or, if large delays are required, by path stretching. Continuous recomputation and display of the capture flight path prior to engaging the system permits the pilot to determine the exact moment for terminating a holding or path stretching maneuver in order to achieve a specified arrival time.

Erzberger, H.↗

Research on fluidics, valves, and proportional amplifiers

Research and development being conducted at the Systems and Controls Laboratory is reviewed. Static characteristics (supply, input, transfer, output, and noise characteristics) of laminar proportional amplifiers were investigated. Other topics discussed include velocity profiles for laminar fluidic jets, speed control systems employing a jet pipe valve, and power amplification with a vortex valve.

Source record↗

A simulation investigation of cockpit display of aircraft traffic during curved, descending, decelerating approaches

The results of a simulation experiment involving the evaluation of cockpit display of aircraft traffic information are presented. The experiment was conducted using taped time dependent, noninteractive traffic in an approach to landing situation and two levels of pilot control models: 3-D automatic and computer augmented control. The tests involved two cases: the simulation aircraft flew approach paths which (1) followed another aircraft in between two other aircraft, and (2) merged between two other aircraft. Speed control via manual throttles was used in all tests (path stretching was not allowed for maintaining separation between aircraft). The approaches were conducted while the simulation aircraft was conducting a curved, descending, decelerating approach to landing. Performance data sets were examined, and subjective opinions regarding workload were gathered. Traffic positioning was varied to further evaluate the test subjects' monitoring performance.

Steinmetz, G. G.↗

Flightcrew Thrust Control and Engine Display Concepts for the Subsonic Single Aft Engine (SUSAN) Transport Aircraft

NASA is developing a new hybrid-electric aircraft concept called the SUbsonic Single Aft eNgine (SUSAN) Electrofan. The SUSAN airplane is being designed as a 180-passenger commercial regional jet and is expected to fly in the 2040 time frame. The flight deck of the SUSAN airplane is expected to resemble a typical two flightcrew transport. Research issues include pilot control and the display elements needed for the hybrid-electric propulsion system. This paper describes a research study conducted in a high-fidelity simulator where 14 commercial pilots evaluated throttle controls and engine display concepts for a proposed SUSAN flight deck. The results showed that the number of throttle levers did not affect pilot’s situation awareness, workload, or speed control.

hybrid electric aircraft↗

Comparison of Aircraft Models and Integration Schemes for Interval Management in the TRACON

Reusable models of common elements for communication, computation, decision and control in air traffic management are necessary in order to enable simulation, analysis and assurance of emergent properties, such as safety and stability, for a given operational concept. Uncertainties due to faults, such as dropped messages, along with non-linearities and sensor noise are an integral part of these models, and impact emergent system behavior. Flight control algorithms designed using a linearized version of the flight mechanics will exhibit error due to model uncertainty, and may not be stable outside a neighborhood of the given point of linearization. Moreover, the communication mechanism by which the sensed state of an aircraft is fed back to a flight control system (such as an ADS-B message) impacts the overall system behavior; both due to sensor noise as well as dropped messages (vacant samples). Additionally simulation of the flight controller system can exhibit further numerical instability, due to selection of the integration scheme and approximations made in the flight dynamics. We examine the theoretical and numerical stability of a speed controller under the Euler and Runge-Kutta schemes of integration, for the Maintain phase for a Mid-Term (2035-2045) Interval Management (IM) Operational Concept for descent and landing operations. We model uncertainties in communication due to missed ADS-B messages by vacant samples in the integration schemes, and compare the emergent behavior of the system, in terms of stability, via the boundedness of the final system state. Any bound on the errors incurred by these uncertainties will play an essential part in a composable assurance argument required for real-time, flight-deck guidance and control systems,. Thus, we believe that the creation of reusable models, which possess property guarantees, such as safety and stability, is an innovative and essential requirement to assessing the emergent properties of novel airspace concepts of operation.

Neogi, Natasha↗