Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stretchability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Materials and noncoplanar mesh designs for integrated circuits with linear elastic responses to extreme mechanical deformations

Electronic systems that offer elastic mechanical responses to high-strain deformations are of growing interest because of their ability to enable new biomedical devices and other applications whose requirements are impossible to satisfy with conventional wafer-based technologies or even with those that offer simple bendability. This article introduces materials and mechanical design strategies for classes of electronic circuits that offer extremely high stretchability, enabling them to accommodate even demanding configurations such as corkscrew twists with tight pitch (e.g., 90° in ≈1 cm) and linear stretching to “rubber-band” levels of strain (e.g., up to ≈140%). The use of single crystalline silicon nanomaterials for the semiconductor provides performance in stretchable complementary metal-oxide-semiconductor (CMOS) integrated circuits approaching that of conventional devices with comparable feature sizes formed on silicon wafers. Comprehensive theoretical studies of the mechanics reveal the way in which the structural designs enable these extreme mechanical properties without fracturing the intrinsically brittle active materials or even inducing significant changes in their electrical properties. The results, as demonstrated through electrical measurements of arrays of transistors, CMOS inverters, ring oscillators, and differential amplifiers, suggest a valuable route to high-performance stretchable electronics.

36 MATERIALS SCIENCE↗

Conductive Liquid Metal Vitrimer Composites for Reconfigurable and Recyclable Flexible Electronics

Liquid metal (LM) elastomer composites exhibit excellent functionality for stretchable electronics and wearables, but limited recycling and reuse pathways constrain their sustainable use. Here, to address these challenges amid growing concerns over electronic waste, a conductive LM–vitrimer composite is presented that enables recyclable and reconfigurable electronics. This soft and stretchable composite features uniformly distributed LM inclusions that enhance thermal conductivity by 6.53× and enable the formation of conductive traces with electrical self-healing, while the vitrimer provides structural restoration. The dynamic covalent bonds of the vitrimer matrix are leveraged for both reprocessing the composite and chemically recovering 94% of the LM. This liquid-state filler slightly reduces the vitrimer's stiffness to 2.63 MPa (≈20% lower), while maintaining its high stretchability (>135% strain) and thermal stability. It is further examined how ultrasonicated LM inclusions interact with the vitrimer matrix and demonstrate the composite's self-healing and recyclability through two distinct approaches: 1) thermomechanical reprocessing, which restores fragmented composites under heat and compression for circuit reconfiguration; and 2) chemical recycling, which recovers the embedded LM for reuse in fabricating new composites and redesigned circuitry. With the integration of recyclability and diverse functional capabilities, LM–vitrimer composites emerge as a promising material platform for sustainable, flexible electronics.

Han, Youngshang [Univ. of Washington, Seattle, WA ↗

Design of Star‐Shaped Trimer Acceptors for High‐Performance (Efficiency > 19%), Photostable, and Mechanically Robust Organic Solar Cells

Abstract High power conversion efficiency (PCE), long‐term stability, and mechanical robustness are prerequisites for the commercial applications of organic solar cells (OSCs). In this study, a new star‐shaped trimer acceptor (TYT‐S) is developed and high‐performance OSCs with a PCE of 19.0%, high photo‐stability (t 80% lifetime = 2600 h under 1‐sun illumination), and mechanical robustness with a crack‐onset strain (COS) of 21.6% are achieved. The isotropic molecular structure of TYT‐S affords efficient multi‐directional charge transport and high electron mobility. Furthermore, its amorphous structure prevents the formation of brittle crystal‐to‐crystal interfaces, significantly enhancing the mechanical properties of the OSC. As a result, the TYT‐S‐based OSCs demonstrate a significantly higher PCE (19.0%) and stretchability (COS = 21.6%) than the linear‐shaped trimer acceptor (TYT‐L)‐based OSCs (PCE = 17.5% and COS = 6.4%) and the small‐molecule acceptor (MYT)‐based OSCs (PCE = 16.5% and COS = 1.3%). In addition, the increased molecular size of TYT‐S, relative to that of MYT and dimer (DYT), suppresses the diffusion kinetics of the acceptor molecules, substantially improving the photostability of the OSCs. Finally, to effectively demonstrate the potential of TYT‐S, intrinsically stretchable (IS)‐OSCs are constructed. The TYT‐S‐based IS‐OSCs exhibit high device stretchability (strain at PCE 80% = 31%) and PCE of 14.4%.

Chemistry↗

Reinforced double-threaded slide-ring networks for accelerated hydrogel discovery and 3D printing

Traditionally, slide-ring gels are stretchable but soft as a result of an elasticity-stretchability trade-off. Herein, we introduce a new approach to breaking this trade-off and creating reinforced slide-ring networks with mobile crosslinkers. Our approach involves the construction of a polyethylene glycol double-threaded γ-cyclodextrin-based pro-slide-ring crosslinker that serves as a modular component for 3D printing and copolymerization. The resulting crystalline-domain-reinforced slide-ring hydrogels, or CrysDoS-gels, exhibit both high elasticity and high stretchability. The modular synthesis allows for high-throughput synthesis of CrysDoS-gels, generating a large amount of data for structure-property analysis. Here, by employing data science techniques, such as machine learning and linear regression, not only were we able to identify which chemical components influence the mechanical properties of CrysDoS-gels, but this analysis also aided in the discovery of better-performing CrysDoS-gels. Finally, we demonstrate the potential application of the newly discovered CrysDoS-gels as sensing devices by 3D printing them as stress sensors with high sensitivity and a broad detection range.

3D-printing↗

Hybrid printing of wearable piezoelectric sensors

Piezoelectricity provides an ideal electromechanical mechanism with emerging applications in wearable devices due to its simplicity and self-powered nature. However, the 3D printing of piezoelectric devices still faces many challenges, including material printability, high energy poling process, and low dimensional accuracy. This study demonstrates, for the first time, a tellurium nanowire-based piezoelectric device fabricated by a hybrid printing method integrating highly complementary aerosol jet printing and extrusion printing in a single printing platform. The aerosol-jet-printed tellurium nanowire demonstrates piezoelectric properties without the need for any poling processing due to the unique properties of the tellurium nanowires. The silver nanowire electrodes printed by aerosol jet printing demonstrate excellent conductivity and stretchability without the need for sintering. An extrusion method is employed to print the silicone films, which serve as the stretchable substrate and the electrical insulation layers between the printed tellurium and silver. The printed wearable piezoelectric devices were attached to a human wrist to detect different hand gestures and to a human neck to detect heartbeat without using an external power source. In conclusion, the fully printed, sintering-free and poling-free, and stretchable piezoelectric device opens enormous opportunities for facile integration with a broad range of printed electronics and wearable devices.

47 OTHER INSTRUMENTATION↗

Tuning the Mechanical Properties of a Polymer Semiconductor by Modulating Hydrogen Bonding Interactions

Conjugation breakers (CBs) with different H-bonding chemistry and linker flexibility are designed and incorporated into a Diketopyrrolopyrrole (DPP)-based conjugated polymer backbone. The effects of H-bonding interactions on polymer semiconductor morphology, mechanical properties and electrical performance are systematically investigated. We observe that CBs with H-bonding self-association constant >0.7 or denser packing tendency are able to induce higher polymer chain aggregation and crystallinity in as-casted thin film, resulting in higher modulus and crack on-set strain. Additionally, the rDoC (relative degree of crystallinity) of the stretched thin film with the highest crack on-set strain only suffers a small decrease, suggesting the main energy dissipation mechanism is the breakage of H-bonding interactions. By contrast, other less stretchable polymer films dissipate strain energy through the breakage of crystalline domains, indicated by drastic decrease in rDoC. Furthermore, we evaluate their electrical performance under mechanical strain in fully stretchable field-effect transistors. The polymer with the highest crack on-set strain has the least degradation in mobility as a function of strain. Overall, these observations suggest that we can aptly tune the mechanical properties in polymer semiconductors by modulating intermolecular interactions, such as H-bonding chemistry and linker flexibility. Such understanding provides molecular design guidelines for future stretchable semiconductors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mechanically tunable conductive interpenetrating network hydrogels that mimic the elastic moduli of biological tissue

Conductive and stretchable materials that match the elastic moduli of biological tissue (0.5–500 kPa) are desired for enhanced interfacial and mechanical stability. Compared with inorganic and dry polymeric conductors, hydrogels made with conducting polymers are promising soft electrode materials due to their high water content. Nevertheless, most conducting polymer-based hydrogels sacrifice electronic performance to obtain useful mechanical properties. Here we report a method that overcomes this limitation using two interpenetrating hydrogel networks, one of which is formed by the gelation of the conducting polymer PEDOT:PSS. Due to the connectivity of the PEDOT:PSS network, conductivities up to 23 S m-1 are achieved, a record for stretchable PEDOT:PSS-based hydrogels. Meanwhile, the low concentration of PEDOT:PSS enables orthogonal control over the composite mechanical properties using a secondary polymer network. We demonstrate tunability of the elastic modulus over three biologically relevant orders of magnitude without compromising stretchability ( > 100%) or conductivity ( > 10 S m-1 ).

36 MATERIALS SCIENCE↗

Sequentially regular polymer acceptors featuring flexible spacers for high-performance and mechanically robust all-polymer solar cells

Developing high-performance and mechanically robust polymer solar cells (PSCs) is crucial for realizing wearable power sources. While efficient all-polymer solar cells (all-PSCs) can be fabricated from polymerized small-molecule acceptors (PSMAs) with high optical absorption and electron mobilities, they still show limited mechanical robustness. Here, we achieve highly efficient and mechanically robust all-PSCs by designing a PSMA (PYFS-Reg) containing sequence-regular flexible spacers (FSs). The regular incorporation of the FS units into PSMAs is essential in simultaneously improving the electrical and mechanical properties of blend films. As a result, all-PSCs featuring PYFS-Reg achieve a high power conversion efficiency (PCE = 16.1%) and stretchability (crack onset strain (COS) = 22.4%), outperforming PSMAs without FSs (i.e., PYBDT, PCE = 12.6% and COS = 11.7%) or with randomly distributed FSs (i.e., PYFS-Ran, PCE = 12.2% and COS = 18.1%). Importantly, these all-PSCs are fabricated by an environmentally benign, non-halogenated solvent process. To further demonstrate their feasible applications in wearable devices, we construct intrinsically stretchable (IS) all-PSCs by using PYFS-Reg-based active layers, which exhibit a high PCE (10.6%) and excellent device stretchability (strain at PCE 80% = 36.7%).

14 SOLAR ENERGY↗

Tensile and fatigue behaviors of printed Ag thin films on flexible substrates

Flexible electronics using nanoparticle (NP) printing has been highlighted as a key technology enabling eco-friendly, low-cost, and large-area fabrication. For NP-based printing to be used as a successive alternative to photolithography and vacuum deposition, stretchability and long term reliability must be considered. This paper reports the stretchability and fatigue behavior of 100 nm thick NP-based silver thin films printed on polyethylene-terephthalate substrate and compares it to films deposited by electron-beam evaporation. NP-based films show stretchability and fatigue life comparable to evaporated films with intergranular fracture as the dominant failure mechanism.

36 MATERIALS SCIENCE↗

The Critical Role of Electron-Donating Thiophene Groups on the Mechanical and Thermal Properties of Donor–Acceptor Semiconducting Polymers

Organic semiconducting donor–acceptor polymers are promising candidates for stretchable electronics owing to their mechanical compliance. However, the effect of the electron-donating thiophene group on the thermomechanical properties of conjugated polymers has not been carefully studied. Here, thin-film mechanical properties are investigated for diketopyrrolopyrrole (DPP)-based conjugated polymers with varying numbers of isolated thiophene moieties and sizes of fused thiophene rings in the polymer backbone. Interestingly, it is found that these thiophene units act as an antiplasticizer, where more isolated thiophene rings or bigger fused rings result in an increased glass transition temperature (T g ) of the polymer backbone, and consequently elastic modulus of the respective DPP polymers. Detailed morphological studies suggests that all samples show similar semicrystalline morphology. This antiplasticization effect also exists in para-azaquinodimethane-based conjugated polymers, indicating that this can be a general trend for various conjugated polymer systems. Using the knowledge gained above, a new DPP-based polymer with increased alkyl side chain density through attaching alky chains to the thiophene unit is engineered. The new DPP polymer demonstrates a record low T g , and 50% lower elastic modulus than a reference polymer without side-chain decorated on the thiophene unit. Finally, this work provides a general design rule for making low-T g conjugated polymers for stretchable electronics.

36 MATERIALS SCIENCE↗

Laser-Assisted Reduction of Highly Conductive Circuits Based on Copper Nitrate for Flexible Printed Sensors

Stretchable electronic sensing devices are defining the path toward wearable electronics. High-performance flexible strain sensors attached on clothing or human skin are required for potential applications in the entertainment, health monitoring, and medical care sectors. In this work, conducting copper electrodes were fabricated on polydimethylsiloxane as sensitive stretchable microsensors by integrating laser direct writing and transfer printing approaches. The copper electrode was reduced from copper salt using laser writing rather than the general approach of printing with pre-synthesized copper or copper oxide nanoparticles. An electrical resistivity of 96 μΩ cm was achieved on 40-μm-thick Cu electrodes on flexible substrates. The motion sensing functionality successfully demonstrated a high sensitivity and mechanical robustness. Furthermore, this in situ fabrication method leads to a path toward electronic devices on flexible substrates.

42 ENGINEERING↗

3D Printed Multifunctional, Hyperelastic Silicone Rubber Foam

Highly elastic silicone foams, especially those with tunable properties and multifunctionality, are of great interest in numerous fields. However, the liquid nature of silicone precursors and the complicated foaming process hinder the realization of its three-dimensional (3D) printability. Herein, a series of silicone foams with outstanding performance with regards to elasticity, wetting and sensing properties, multifunctionality, and tunability is generated by direct ink writing. Viscoelastic inks are achieved from direct dispersion of sodium chloride in a unique silicone precursor solution. The 3D-architectured silicone rubber exhibits open-celled trimodal porosity, which offers ultraelasticity with hyper compressibility/cycling endurance (near-zero stress/strain loss under 90% compression or 1000 compression cycles), excellent stretchability (210% strain), and superhydrophobicity. The resulting foam is demonstrated to be multifunctional, such that it can work as an oil sorbent with super capacity (1320%) and customizable soft sensor after absorption of carbon nanotubes on the foam surface. The strategy enables tunability of mechanical strength, elasticity, stretchability, and absorbing capacity, while printing different materials together offers property gradients as an extra dimension of tunability. Finally, the first 3D printed silicone foam, which serves an important step toward its application expansion, is achieved.

36 MATERIALS SCIENCE↗

Effect of Molecular Weight on the Morphology of a Polymer Semiconductor–Thermoplastic Elastomer Blend

Abstract Polymer semiconductors (PSCs) are essential active materials in mechanically stretchable electronic devices. However, many exhibit low fracture strain due to their rigid chain conformation and the presence of large crystalline domains. Here, a PSC/elastomer blend, poly[((2,6‐bis(thiophen‐2‐yl)‐3,7‐bis(9‐octylnonadecyl)thieno[3,2‐b]thieno[2′,3′:4,5]thieno[2,3‐d]thiophene)‐5,5′‐diyl)(2,5‐bis(8‐octyloctadecyl)‐3,6‐di(thiophen‐2‐yl)pyrrolo[3,4‐c]pyrrole‐1,4‐dione)‐5,5′‐diyl]] (P2TDPP2TFT4) and polystyrene‐ block ‐poly(ethylene‐ran‐butylene)‐ block ‐polystyrene (SEBS) are systematically investigated. Specifically, the effects of molecular weight of both SEBS and P2TDPP2TFT4 on the resulting blend morphology, mechanical, and electrical properties are explored. In addition to commonly used techniques, atomic force microscopy‐based nanomechanical images are used to provide additional insights into the blend film morphology. Opposing trends in SEBS‐induced aggregation are observed for the different P2TDPP2TFT4 molecular weights upon increasing the SEBS molecular weight from 87 to 276 kDa. Furthermore, these trends are seen in device performance trends for both molecular weights of P2TDPP2TFT4. SEBS molecular weight also has a substantial influence on the mesoscale phase separation. Strain at fracture increases dramatically upon blending, reaching a maximum value of 640% ± 20% in the blended films measured with film‐on‐water method. These results highlight the importance of molecular weight for electronic devices. In addition, this study provides valuable insights into appropriate polymer selections for stretchable semiconducting thin films that simultaneously possess excellent mechanical and electrical properties.

36 MATERIALS SCIENCE↗

Rapid custom prototyping of soft poroelastic biosensor for simultaneous epicardial recording and imaging

Abstract The growing need for the implementation of stretchable biosensors in the body has driven rapid prototyping schemes through the direct ink writing of multidimensional functional architectures. Recent approaches employ biocompatible inks that are dispensable through an automated nozzle injection system. However, their application in medical practices remains challenged in reliable recording due to their viscoelastic nature that yields mechanical and electrical hysteresis under periodic large strains. Herein, we report sponge-like poroelastic silicone composites adaptable for high-precision direct writing of custom-designed stretchable biosensors, which are soft and insensitive to strains. Their unique structural properties yield a robust coupling to living tissues, enabling high-fidelity recording of spatiotemporal electrophysiological activity and real-time ultrasound imaging for visual feedback. In vivo evaluations of custom-fit biosensors in a murine acute myocardial infarction model demonstrate a potential clinical utility in the simultaneous intraoperative recording and imaging on the epicardium, which may guide definitive surgical treatments.

36 MATERIALS SCIENCE↗

A molecular design approach towards elastic and multifunctional polymer electronics

Next-generation wearable electronics require enhanced mechanical robustness and device complexity. Besides previously reported softness and stretchability, desired merits for practical use include elasticity, solvent resistance, facile patternability and high charge carrier mobility. Here, we show a molecular design concept that simultaneously achieves all these targeted properties in both polymeric semiconductors and dielectrics, without compromising electrical performance. This is enabled by covalently-embedded in-situ rubber matrix (iRUM) formation through good mixing of iRUM precursors with polymer electronic materials, and finely-controlled composite film morphology built on azide crosslinking chemistry which leverages different reactivities with C–H and C=C bonds. The high covalent crosslinking density results in both superior elasticity and solvent resistance. When applied in stretchable transistors, the iRUM-semiconductor film retained its mobility after stretching to 100% strain, and exhibited record-high mobility retention of 1 cm 2 V -1 s -1 after 1000 stretching-releasing cycles at 50% strain. The cycling life was stably extended to 5000 cycles, five times longer than all reported semiconductors. Furthermore, we fabricated elastic transistors via consecutively photo-patterning of the dielectric and semiconducting layers, demonstrating the potential of solution-processed multilayer device manufacturing. The iRUM represents a molecule-level design approach towards robust skin-inspired electronics.

42 ENGINEERING↗

Multifunctional textured graphene-based coatings on elastomeric gloves for chemical protection

Nanotechnology offers a variety of new tools for the design of next-generation personal protective equipment (PPE). One example is the use of two-dimensional materials as coatings that enhance the performance and ergonomics of elastomeric gloves designed to protect users from hazardous chemicals. Desirable features in such coatings may include molecular barrier function, liquid droplet repellency, stretchability for compatibility with the elastomer, breathability, and an ultrathin profile that preserves the user's manual dexterity and tactile sensation. The present work explores the potential of engineered graphene-based films with out-of-plane texturing as a novel platform to meet these multifold requirements. Graphene-based films in different formulations were fabricated from water-borne inks by vacuum filtration and solution casting methods on glove-derived nitrile rubber substrates. The various coatings were then subjected to tests of molecular permeation by model volatile organic compounds, droplet contact angle, breathability, and mechanical stability during stretching and solvent immersion. The films dramatically improve the barrier properties of glove-derived nitrile. The out-of-plane graphene texturing imparts stretchability through microscale folding/unfolding, while also enhancing droplet repellency in some cases through a lotus-like roughening effect. The combined results suggest that engineered textured graphene-based films are a promising platform for creating multifunctional coatings for a next generation of chemically protective gloves and other elastomer-based PPE.

36 MATERIALS SCIENCE↗