Search NASA⌕ Search

SEARCH · Search NASA

Results for “TIME RESOLUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Quadrant anode image sensor

A position-sensitive event-counting electronic readout system for microchannel plates (MCPs) is described that offers the advantages of high spatial resolution and fast time resolution. The technique relies upon a four-quadrant electron-collecting anode located behind the output face of the microchannel plate, so that the electron cloud from each detected event is partly intercepted by each of the four quadrants. The relative amounts of charge collected by each quadrant depend on event position, permitting each event to be localized with two ratio circuits. A prototype quadrant anode system for ion, electron, and extreme ultraviolet imaging is described. The spatial resolution achieved, about 10 microns, allows individual MCP channels to be distinguished.

Lampton, M.↗
NASA NTRS1976

Characteristics of cosmic X-ray bursts observed with the OGO-5 satellite

Observations of 11 cosmic X-ray bursts made with the solar X-ray spectrometer aboard OGO 5 are presented. Their identification as cosmic events is based on good time coincidence with observations of cosmic gamma-ray bursts reported in the literature. The OGO-5 experiment is most sensitive to cosmic X-ray sources located in the sunward hemisphere. When this condition was satisfied and the OGO-5 experiment was operating normally, almost every cosmic gamma-ray burst reported by other observers was detected at X-ray energies of at least 32 keV. In three events the spectrum was observed down to about 10 keV. Two intense events were observed with 0.288-s time resolution, and large time variations were observed to occur in times not exceeding 0.3 s. Evidence is found that most cosmic gamma-ray bursts have photon spectra extending down to about 10 keV. The origin of these cosmic events in processes similar to those believed to occur in solar flares is briefly examined.

Kane, S. R.↗
NASA NTRS1979

Inflight lightning characteristics measurement system

A research data-gathering system being developed for inflight measurement of direct and nearby lightning strike characteristics is described. Wideband analog recorders used to record the lightning scenario are supplemented with high-sample-rate digital transient recorders with augmented memory capacity for increased time resolution of specific times of interest. The endless-loop data storage technique employed by the transient recorders circumvents problems associated with oscilloscopic techniques and allows unattended operation. System integrity and immunity from induced effects is accomplished by fiber-optics signal-transmission links, shielded system enclosures, and the use of a dynamotor for power system isolation.

Pitts, F. L.↗
NASA NTRS1980

The recognition of extraterrestrial artificial signals

Considerations in the design of receivers for the detection and recognition of artificial microwave signals of extraterrestrial origin are discussed. Following a review of the objectives of SETI and the probable reception and detection characteristics of extraterrestrial signals, means for the improvement of the sensitivity, signal-to-noise ratios and on-line data processing capabilities of SETI receivers are indicated. The characteristics of the signals likely to be present at the output of an ultra-low-noise microwave receiver are then examined, including the system background noise, terrestrial radiations, astrophysical radiations, accidental artificial radiations of terrestrial origin, and intentional radiations produced by humans and by extraterrestrial intelligence. The classes of extraterrestrial signals likely to be detected, beacons and leakage signals, are considered, and options in the specification of gating and thresholding for a high-spectral resolution, high-time-resolution signal discriminator are indicated. Possible tests for the nonhuman origin of a received signal are also pointed out.

Seeger, C. L.↗
NASA NTRS1981

Direct strike lightning measurement system

A research data system developed for in-flight measurement of direct and nearby lightning-strike characteristics is described. The measurement system consists of a wide-band analog recorder which records the continuous lightning scenario and fast sample-rate digital transient recorders with augmented memory capacity for increased time resolution of specific times of interest. Electromagnetic sensors with bandwidths exceeding 100 MHz are used which respond to rates of change of the quantities being measured. Data system immunity from electromagnetic interference is accomplished by the use of a dynamotor for power isolation, shielded system enclosure and fiber-optic data links.

Thomas, M. E.↗
NASA NTRS1983

A portable telescope, photometer, and data-recording system

A description is presented of a portable telescope, two-channel photometer and high-speed data-recording system that meet the unique requirements of occultation astronomy. The instrumentation has been designed for portability, high time resolution, accurate absolute timing, and ease of use. The instrumentation includes a light-weight 35.5-cm (14-inch) objective portable telescope, a two-channel high-speed photometer and a data-recording system built into a suitcase. The equipment has been successfully used in field operations and at fixed observatories in India, Australia, and Hawaii.

Baron, R. L.↗
NASA NTRS1984

Overview of on-line data processing for MST radars (keynote paper), part 7

The most important aspects of the processing of MST radar data are discussed. The important points of on-line data processing for MST radar are reviewed. The goals of the on-line and now almost exclusively digital processing, procedures are to achieve good altitude resolution and coverage, good frequency (Doppler shift) resolution, and good time resolution, while avoiding, the problems of range and frequency ambiguity (aliasing), ground clutter, and interference. Achieving optimum results requires pulse compression and some coherent integration. The first allows full utilization of the average power capability of the transmitter and the second reduces the computing requirements.

Farley, D. T.↗
NASA NTRS1988

Striated spectral activity in Jovian and Saturnian radio emission

Examination of high time resolution frequency-time spectrograms of radio emission measured near the Voyager 1 and 2 encounters with Jupiter reveals occasional striation patterns within the normally diffuse hectometric radiation. The patterns are characterized by distinctive banded structures of enhanced intensity meandering in frequency over time scales of minutes to tens of minutes. This banded form of striated spectral activity (SSA) has an occurrence probability of the order of 5 percent during the three weeks before and after Jupiter encounters. Plots of single 6-s frequency sweeps often exhibit a slow rise in intensity followed by a sharp drop-off in each band as frequency decreases. Banded SSA is often preceded or followed by chaotic SSA in which banding of the emission becomes discontinuous or unrecognizable, although the intensity modulation is still evident. Although SSA normally occurs in the frequency range of roughly 0.2-1.0 MHz, similar but longer-lasting patterns have been found occasionally in decametric emission above 10 MHz. Analogous modulation has also been observed in the Saturnian radio emission, suggesting that SSA may be a common feature intrinsic to the radio emission at both planets.

Thieman, James R.↗
NASA NTRS1988

Imaging solar flares in hard X-rays and gamma raysfrom balloon-borne platforms

Hard X-rays and gamma rays carry the most direct evidence available for the roles of accelerated particles in solar flares. An approach that employs a spatial Fourier-transform technique for imaging the sources of these emissions is described and plans for developing a balloon-borne gamma ray imaging device (GRID) based on this instrumental approach is presented. This instrument, GRID on a balloon, would enable observations with a 1.6 arcsecond angular resolution, 10 millisecond time resolution, and whole-Sun field of view on long-duration balloon flights during MAX 1991.

Crannell, Carol JO↗
NASA NTRS1991

A balloon-borne payload for imaging hard X-rays and gamma rays from solar flares

Hard X-rays and gamma rays provide direct evidence of the roles of accelerated particles in solar flares. An approach that employs a spatial Fourier-transform technique for imaging the sources of these emissions is described, and the development of a balloon-borne imaging device based on this instrumental technique is presented. The detectors, together with the imaging optics, are sensitive to hard X-ray and gamma-ray emission in the energy-range from 20 to 700 keV. This payload, scheduled for its first flight in June 1992, will provide 11-arc second angular resolution and millisecond time resolution with a whole-sun field of view. For subsequent flights, the effective detector area can be increased by as much as a factor of four, and imaging optics with angular resolution as fine as 2 arcsec can be added to the existing gondola and metering structures.

Crannell, Carol J.↗
NASA NTRS2000

Corongraphic Observations and Analyses of The Ultraviolet Solar Corona

The activities supported under NASA Grant NAG5-613 included the following: 1) reduction and scientific analysis of data from three sounding rocket flights of the Rocket Ultraviolet Coronagraph Spectrometer, 2) development of ultraviolet spectroscopic diagnostic techniques to provide a detailed empirical description of the extended solar corona, 3) extensive upgrade of the rocket instrument to become the Ultraviolet Coronal Spectrometer (UVCS) for Spartan 201,4) instrument scientific calibration and characterization, 5) observation planning and mission support for a series of five Spartan 201 missions (fully successful except for STS 87 where the Spartan spacecraft was not successfully deployed and the instruments were not activated), and 6) reduction and scientific analysis of the UVCS/Spartan 201 observational data. The Ultraviolet Coronal Spectrometer for Spartan 201 was one unit of a joint payload and the other unit was a White Light Coronagraph (WLC) provided by the High Altitude Observatory and the Goddard Space Flight Center. The two instruments were used in concert to determine plasma parameters describing structures in the extended solar corona. They provided data that could be used individually or jointly in scientific analyses. The WLC provided electron column densities in high spatial resolution and high time resolution. UVCS/Spartan provided hydrogen velocity distributions, and line of sight hydrogen velocities. The hydrogen intensities from UVCS together with the electron densities from WLC were used to determine hydrogen outflow velocities. The UVCS also provided O VI intensities which were used to develop diagnostics for velocity distributions and outflow velocities of minor ions.

Kohl, John L.↗
NASA NTRS2011

High-Performance Wireless Telemetry

Prior technology for machinery data acquisition used slip rings, FM radio communication, or non-real-time digital communication. Slip rings are often noisy, require much space that may not be available, and require access to the shaft, which may not be possible. FM radio is not accurate or stable, and is limited in the number of channels, often with channel crosstalk, and intermittent as the shaft rotates. Non-real-time digital communication is very popular, but complex, with long development time, and objections from users who need continuous waveforms from many channels. This innovation extends the amount of information conveyed from a rotating machine to a data acquisition system while keeping the development time short and keeping the rotating electronics simple, compact, stable, and rugged. The data are all real time. The product of the number of channels, times the bit resolution, times the update rate, gives a data rate higher than available by older methods. The telemetry system consists of a data-receiving rack that supplies magnetically coupled power to a rotating instrument amplifier ring in the machine being monitored. The ring digitizes the data and magnetically couples the data back to the rack, where it is made available. The transformer is generally a ring positioned around the axis of rotation with one side of the transformer free to rotate and the other side held stationary. The windings are laid in the ring; this gives the data immunity to any rotation that may occur. A medium-frequency sine-wave power source in a rack supplies power through a cable to a rotating ring transformer that passes the power on to a rotating set of electronics. The electronics power a set of up to 40 sensors and provides instrument amplifiers for the sensors. The outputs from the amplifiers are filtered and multiplexed into a serial ADC. The output from the ADC is connected to another rotating ring transformer that conveys the serial data from the rotating section to the stationary section. From there, a cable conveys the serial data to the remote rack, where it is reconditioned to logic level specifications, de-serialized, and converted back to analog. In the rotating electronics are code generators to indicate the beginning of files for data synchronization.

Griebeler, Elmer↗
NASA NTRS2025

Evolving the SpaceFOM: Lessons Learned and Future Development

For over fifty years, simulation has been a cornerstone technology for space missions. In many cases, one single simulator, developed by one team, is not enough to meet the simulation objectives. Astronaut crew training, docking, vehicle testing and complex mission planning all require several simulations to be connected and to interoperate, in order to achieve the goal of the simulation. To facilitate the development of interoperable simulations, an open standard, the SISO SpaceFOM was developed in collaboration between government, industry and academia. The standard was released in 2020. The initial release of SpaceFOM focuses on the core interoperability topics for space simulation: (i) specifying spatial data using several, well defined reference frames, (ii) managing time (including real-time, hard real-time, and as-fast-as-possible execution), (iii) composition of systems with subsystems such as space vehicles, and (iv) execution control, such as initializing, running, pausing, and terminating simulations. The initial release of SpaceFOM focuses on the core interoperability topics for space simulation: (i) specifying spatial data using several, well defined reference frames, (ii) managing time (including real-time, hard real-time, and as-fast-as-possible execution), (iii) composition of systems with subsystems such as space vehicles, and (iv) execution control, such as initializing, running, pausing, and terminating simulations. A number of requirements for the next version of SpaceFOM have been identified and proposed solutions are already under development. One key area is the object classes used for data exchange, where a richer set of classes have been proposed, based on practical use cases. For time management, the use of variable time resolutions and variable time steps is also proposed. For execution control, save and restore of simulations is considered as well as improved robustness, to handle failing components. A number of clarifications are also under consideration. This paper provides both a forward-looking view of the technical developments underway and a retrospective on the standard's evolution. The authors emphasize that prioritizing core challenges and delivering a practical first version were crucial steps. While not every idea was implemented in the initial release, the timely delivery of a functional standard enabled real-world applications, the growth of a user community, and the collection of valuable insights to shape future versions. The authors look forward to working with the next version of SpaceFOM together with the growing user community.

Simulation Interoperability↗
NASA NTRSDate not supplied

Evolving the SpaceFOM: Lessons Learned and Future Development

For over fifty years, simulation has been a cornerstone technology for space missions. In many cases, one single simulator, developed by one team, is not enough to meet the simulation objectives. Astronaut crew training, docking, vehicle testing and complex mission planning all require several simulations to be connected and to interoperate, in order to achieve the goal of the simulation. To facilitate the development of interoperable simulations, an open standard, the SISO SpaceFOM was developed in collaboration between government, industry and academia. The standard was released in 2020. The initial release of SpaceFOM focuses on the core interoperability topics for space simulation: (i) specifying spatial data using several, well defined reference frames, (ii) managing time (including real-time, hard real-time, and as-fast-as-possible execution), (iii) composition of systems with subsystems such as space vehicles, and (iv) execution control, such as initializing, running, pausing, and terminating simulations. A number of requirements for the next version of SpaceFOM have been identified and proposed solutions are already under development. One key area is the object classes used for data exchange, where a richer set of classes have been proposed, based on practical use cases. For time management, the use of variable time resolutions and variable time steps is also proposed. For execution control, save and restore of simulations is considered as well as improved robustness, to handle failing components. A number of clarifications are also under consideration. This paper provides both a forward-looking view of the technical developments underway and a retrospective on the standard's evolution. The authors emphasize that prioritizing core challenges and delivering a practical first version were crucial steps. While not every idea was implemented in the initial release, the timely delivery of a functional standard enabled real-world applications, the growth of a user community, and the collection of valuable insights to shape future versions. The authors look forward to working with the next version of SpaceFOM together with the growing user community.

FOMs↗
DOE OSTI2020

Recent Development of Frequency Estimation Methods for Future Smart Grid

The frequency estimated by the Phasor Measurement Unit (PMU) is a critical index of power system status and supports many smart grid applications. The future smart grid features high penetration of renewables and more fast-moving power electronics inverters but raises challenges to the reliable frequency estimation. This article presents three methods to address these challenges. First, an enhanced zero-crossing algorithm was developed to track the fast-changing frequency in system dynamics. Second, we propose a technology that can tolerate the system transient and suppress the outliers. Third, an algorithm was developed to export high time-resolution frequency estimations with minimum computational effort. All of the proposed methods are realized in hardware and compared with classical frequency estimation methods. The testing results indicate that the proposed methods have excellent performance. They can be used in future PMUs and provide reliable and high time resolution data for smart grid applications.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Design and calibration of an optically segmented single volume scatter camera for neutron imaging

The Optically Segmented Single Volume Scatter Camera (OS-SVSC) aims to image neutron sources for non-proliferation applications using the kinematic reconstruction of elastic double-scatter events. Our prototype system consists of 64 EJ-204 organic plastic scintillator bars, each measuring 5mm × 5mm × 200mm and individually wrapped in Teflon tape. The scintillator array is optically coupled to two silicon photomultiplier ArrayJ-60035 64P-PCB arrays, each comprised of 64 individual 6x6mm J-Series sensors arranged in an 8 × 8 array. We report on the design details, including component selections, mechanical design and assembly, and the electronics system. The described design leveraged existing off-the-shelf solutions to support the rapid development of a phase 1 prototype. Several valuable lessons were learned from component and system testing, including those related to the detector's mechanical structure and electrical crosstalk that we conclude originates in the commercial photodetector arrays and the associated custom breakout cards. We detail our calibration efforts, beginning with calibrations for the electronics, based on the IRS3D application-specific integrated circuits, and their associated timing resolutions, ranging from 3090ps. With electronics calibrations applied, energy and position calibrations were performed for a set of edge bars using 22 Na and 90 Sr, respectively, reporting an average resolution of 12.07±0.03mm for energy depositions between 900keVee and 1000keVee. We further demonstrate a position calibration method for the internal bars of the matrix using cosmic-ray muons as an alternative to emission sources that cannot easily access these bars, with an average measured resolution of 14.86+-0.29mm for depositions between 900keVee and 1000keVee. The coincident time resolution reported between pairs of bars measured up to 400ps from muon acquisitions. Energy and position calibration values measured with muons are consistent with those obtained using particle emission sources.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Fast timing with µRWELL-PICOSEC detector technology

The µWELL-PICOSEC detector, which is based on Resistive Micro-Well (µRWELL) technology, is a novel concept for fast timing gaseous detectors that can provide timing resolution in the tens of picosecond range, making it ideal candidate for time-of-flight (TOF) technology for particle identification (PID) in particle physics experiments as well as for future medical instrumentation. The µRWELL-PICOSEC concept is based on a Cerenkov radiator that produces Cerenkov photons from high energetic charged particles, a photocathode layer that converts the Cerenkov photons into primary electrons, a µRWELL amplification layer that multiply the electrons through amplification in a CF4-based gas mixture and a pad-segmentation anode readout coupled with fast timing electronics to provide fast signal. Beam tests were carried out at the CERN SPS H4 beamline in summer 2023 and 2024. Preliminary results show timing performance of the order of 23 ps achievable with µRWELL-PICOSEC prototype. and position scan of the 100-pads of a multi-channel prototype was also performed to study time response uniformity of large area detector. In this talk, after a brief overview of the PICOSEC technology, we will present recent results with different single channel µRWELL-PICOSEC prototype designs and also the position scan results of the 100-pads large prototype to study timing response uniformity for large area µRWELL-PICOSEC detector. Finally, we will discuss the ongoing R&D effort to further improve the timing resolution and allow good position capabilities through charge sharing for large area.

Gnanvo, Kondo↗
NASA NTRS1997

Analysis of STIS time-tag data

Very high time resolution data can be obtained from the Space Telescope Imaging Spectrograph (STIS) Multi-Anode Microchannel Array (MAMA) detectors using the time-tag observing mode. In this mode, the photon events are not accumulated onboard the spacecraft. Instead, each event is recorded internally and transmitted to the ground as an X and Y location with an event time. Event times are recorded in units of 125 microseconds. Analysis of STIS Crab Pulsar data demonstrates that a time resolution of approaching 125 microseconds can be achieved. Furthermore, the time-tag observing mode has been demonstrated to be a very powerful diagnostic tool and can be used to increase the resolution of both imaging and spectral data.

Lindler, Don J.↗