Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tapes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Mono‐Materials Created by Engineering a Continuum of P3HB Stereomicrostructures in a One‐Step Catalytic Process

Multi-material products that combine multiple complementary polymers can create products with desired performance but present challenges to end-of-life (EoL) management. The emerging mono-material product design based on a single polymer type addresses the fundamental EoL issue, but challenges of delivering vastly tunable material properties by the single polymer still remain. Here, we introduce a simple strategy to produce biodegradable poly(3-hydroxybutyrate) (P3HB) materials with a wide range of material properties by engineering a stereomicrostructure continuum, achieved through polymerizing diastereomeric mixtures of racemic and meso-dimethyl diolides at various feed ratios with a single catalyst. This one-step, one-pot process produces biodegradable P3HB mono-materials ranging from rigid to flexible thermoplastics, to tough thermoplastic elastomers, to a pressure-sensitive adhesive (PSA), which have been then combined to fabricate prototype all-P3HB PSA tapes, demonstrating the feasibility of designing mono-material products through engineering polymer stereomicrostructures.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Two-layer cathode architecture for high-energy density and high-power density solid state batteries

Solid state batteries with high-energy density and high-power density require the development of thick and energy dense cathodes. Structured cathode electrodes with a double-layer configuration were enabled using a freeze tape casting technique. A bottom dense layer was utilized to enhance the energy density whereas a top porous layer with vertically aligned walls was utilized to enhance the power density. The porous structure of the power layer was achieved by ice templating this layer on top of the densified energy layer of the cathode. This configuration was found to better utilize the active material of the cathodes and was optimized using numerical simulation and computer modeling. Cells with Li metal anode and LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) at approximately 5 and 20 mg/cm 2 were cycled at 70 °C at different C-rates. Poly(ethylene oxide) (PEO) with lithium bis-trifluoromethanesulfonimide (LiTFSI) was used for the catholyte and the solid-state electrolyte. The structured cathodes exhibited more than double capacity values as well as better Coulombic efficiency compared to non-structured (single-layer) thick cathodes. In conclusion, synchrotron X-ray tomography and scanning electron microscopy were used to characterize the microstructure of the cathodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Review of heat transfer enhancement techniques for single phase flows

The thermal energy exchange between a flowing fluid and its confining channel is a ubiquitous process in modern society. To enhance the fluid-to-wall or wall-to-fluid heat transfer, several techniques have been developed to maximize the contact area between the fluid and the inner wall and/or disrupt the flow to enhance circulation or induce turbulence. Deployment of channels having features capable of enhancing heat transfer enables the reduction of heat exchanger size while maintaining performance. Reduction in equipment size is critical due to the ability to minimize the required volume of costly working fluids and to mitigate potential safety concerns associated with total system fluid volume. Here, a comprehensive review of single-phase heat transfer enhancement techniques is presented. The article provides a thorough comparison by analyzing the heat transfer rate, pressure drop, and other operational aspects. Single-phase heat transfer enhancement methods are divided into active and passive techniques. Active methods such as electrohydrodynamic (EHD), magnetohydrodynamics (MHD), or mechanical motion require external power to create enhancement. Passive methods such as dimples, fins, or tape inserts do not require external input and rely only on surface modification. Although active methods are more expensive and difficult to implement compared to passive techniques, it enables active control of heat transfer augmentation. Finally, this review develops and summarizes key learning data for design optimization enabled by additive manufacturing and machine learning algorithms, helping to inform these next-generation heat exchanger design methodologies for a plethora of modern applications such as electrification of vehicles, computing, and classical industries.

42 ENGINEERING↗
DOE OSTI2022

Atmospheric plasma spraying to fabricate metal‐supported solid oxide fuel cells with open‐channel porous metal support

Abstract Metal‐supported solid oxide fuel cells (MS‐SOFCs) have been fabricated by applying phase‐inversion tape‐casting and atmospheric plasma spraying (APS). The effect of the binder amount of the phase‐inversion slurries on the microstructure development of the 430L stainless steel metal support was investigated. The pore structures, the viscosity of the slurry, porosity and permeability of the as‐prepared metal supports are significantly influenced by the amount of the binder. NiO–scandia‐stabilized zirconia (ScSZ) anode, ScSZ electrolyte and La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3−δ (LSCF) cathode layers were consecutively deposited on the metal support with an ideal microstructure by APS process. The effect of plasma power of the APS on the microstructure of the electrolyte and cathode was investigated. A dense electrolyte layer and a porous cathode layer were successfully obtained at 40 and 6 kW of the APS plasma power, respectively. MS‐SOFCs, with a cell configuration of 430L/Ni‐ScSZ/ScSZ/LSCF, achieved a maximum cell power density of 1079 mW cm −2 at 700°C using humidified H 2 as fuel and ambient air as oxidant. The corresponding ohmic resistance and total resistance of MS‐SOFCs was 0.14 and 0.32 Ω cm 2 , respectively. This work demonstrates the feasibility of fabricating high‐performance MS‐SOFCs with economical and scalable techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Improving the damage tolerance of Si 3 N 4 by forming laminate composites with refractory metals

The objective of this research was to demonstrate that the damage tolerance of Si 3 N 4 could be significantly improved by forming laminate composites with refractory metals, providing materials that undergo graceful failure, rather than the fast-fracture mechanism exhibited by monolithic Si 3 N 4 . A damage tolerant Si 3 N 4 could be used as a ring material in an all-ceramic bearing, decreasing the chance for catastrophic failure if the ring is stressed in tension during operation. The technical approach formed a laminate composite material using alternating Si 3 N 4 -metallic layers, with both outer layers being Si 3 N 4 to take advantage of its greater wear resistance, chemical stability, and thermal stability. The metallic layers are designed to arrest any cracks in the outer layers, thus producing a toughened Si 3 N 4 and avoiding the catastrophic failure behavior exhibited by monolithic ceramics. The laminate composites were fabricated using a combination of tape-casting Si 3 N 4 and metals from slurries, as well as metal foils, followed by hot pressing at 1500°C. The metallic materials employed were chromium, titanium, and tantalum. Analysis confirmed that the interfaces were well formed, and the laminates with chromium and titanium formed intermetallic compounds more readily than the composites with tantalum. The Si 3 N 4 -Ta laminates demonstrated crack deflection and bridging behavior during failure and flexural strength of 800–900 MPa. The hardness and elastic modulus of Si 3 N 4 -Ta laminates measured by nanoindentation were similar to those reported in literature. The hardness across the interface of the Si 3 N 4 -Ta composite varied according to the composition of the interface, which displayed a profile indicative of a diffusion bond.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of iron and silica nanoparticles’ size on in vitro human skin binding and penetration

This in vitro skin study determined absorption, diffusion, and binding rates of four [14C]-labeled nanoparticles (NPs): 12 nm Fe 3 O 4 , 32 nm Fe 3 O 4 @SiO 2 , 33 nm SiO 2 , and 78 nm SiO 2 in each layer of human cadaver skin. In vitro microdialysis device and flow-through skin diffusion system were used to measure the binding affinity to the stratum corneum (SC) and permeability into/through skin layer of the four NPs with different physical–chemical properties, respectively, in short (30 min) and/or long (24 hours) exposures. Results show that NP size is an important factor affecting NP percutaneous absorption. The 12 nm Fe 3 O 4 NPs reached the SC and viable epidermis; 32 nm Fe 3 O 4 @SiO 2 core/shell NPs only reached SC. However, 33 nm and 78 nm silica NPs did not permeate SC. Similar patterns were observed for NP binding affinity to SC and dermatopharmacokinetic analysis using the tape stripping method. The binding affinity determination may be a useful method to efficiently screen skin penetration of NPs.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Design, Fabrication, and Screening of Environmental‐Thermal Barrier Coatings Prepared by Ultrafast High‐Temperature Sintering

Abstract The demand for more efficient gas turbines relies heavily on the development of new environmental‐thermal barrier coatings (ETBCs). However, there is still uncertainty about which alloys and composites will be used for the next generation of turbine blades, as well as the most promising coating materials. Herein, an ETBCs development strategy is presented by integrating the coating design, synthesis, and screening using an ultrafast high temperature sintering (UHS) technique to accelerate coating improvements. The initial basis for composition selection is their thermal expansion mismatch with the substrate alloys; for which a temperature‐dependent coefficient of thermal expansion database is created. By combining tape casting method with the UHS technique a high‐throughput synthesis of single and multi‐layer coatings are realized with different compositions, layer stacking sequences, and layer thicknesses. To evaluate the coatings, thermal cycling tests from room temperature to 1300 °C are conducted. The approach enabled coatings on objects with complex geometries, multi‐layer ETBCs, and porosity tailoring by using staged UHS that runs with different temperatures and durations. The fast iteration strategy is more cost‐effective for the screening of ETBCs compared to conventional methods and greater throughput which can be further extended for rapid optimization of other materials systems.

Xie, Hua↗
DOE OSTI2021

Multifunctional Separator Allows Stable Cycling of Potassium Metal Anodes and of Potassium Metal Batteries

Here, this is the first report of a multifunctional separator for potassium-metal batteries (KMBs). Here, double-coated tape-cast microscale AlF 3 on polypropylene (AlF 3 @PP) yields state-of-the-art electrochemical performance: symmetric cells are stable after 1000 cycles (2000 h) at 0.5 mA cm –2 and 0.5 mAh cm –2 , with 0.042 V overpotential. Stability is maintained at 5.0 mA cm –2 for 600 cycles (240 h), with 0.138 V overpotential. Postcycled plated surface is dendrite-free, while stripped surface contains smooth solid electrolyte interphase (SEI). Conventional PP cells fail rapidly, with dendrites at plating, and “dead metal” and SEI clumps at stripping. Potassium hexacyanoferrate(III) cathode KMBs with AlF 3 @PP display enhanced capacity retention (91% at 100 cycles vs 58%). AlF 3 partially reacts with K to form an artificial SEI containing KF, AlF 3 , and Al 2 O 3 phases. The AlF 3 @PP promotes complete electrolyte wetting and enhances uptake, improves ion conductivity, and increases ion transference number. The higher of K + transference number is ascribed to the strong interaction between AlF 3 and FSI – anions, as revealed through 19 F NMR. The enhancement in wetting and performance is general, being demonstrated with ester- and ether-based solvents, with K-, Na-, or Li- salts, and with different commercial separators. In full batteries, AlF 3 prevents Fe crossover and cycling-induced cathode pulverization.

NMB↗
DOE OSTI2025

Recent Advances in Scalable, High‐Mass Loaded Electrodes for Grid‐Scale Energy Storage

Abstract The increasing electrification of daily life as well as the intermittent characteristic of renewable energy sources require viable solutions for grid‐scale energy storage. Critical considerations for grid storage applications are electrode mass loading and electrode thickness as these features govern battery pack energy density, an important factor in determining manufacturing costs. For this reason, there is increased interest in finding new ways of creating electrodes with high mass loading. In this review, various high‐mass loading fabrication approaches are considered for positive electrode materials used in batteries. The benchmark used for high mass loading is above 20 mg cm −2 , which is higher than the practical limit of conventional tape‐cast electrodes. Several different electrode approaches are described including templating, laser patterning, direct ink writing, and electrodeposition. A variety of materials are covered with the most prominent being LiFe(PO 4 ) (LFP), LiCoO 2 (LCO), and MnO 2 . In research to date, scalable electrochemical performance has been achieved with mass loadings over 100 mg cm −2 . Areal capacities as high as 14.7 mAh cm −2 at 1.82 mA cm −2 have been achieved in non‐aqueous electrolytes and 9.8 mAh cm −2 at 10 mA cm −2 in aqueous electrolytes. These results establish that the mass loading of electrodes can be scaled up without compromising their electrochemical properties.

White, Makena [Department of Materials Science and↗
DOE OSTI2024

Direct Exfoliation of Nanoribbons from Bulk van der Waals Crystals

Confinement of monolayers into quasi-1D atomically thin nanoribbons could lead to novel quantum phenomena beyond those achieved in their bulk and monolayer counterparts. However, current experimental availability of nanoribbon species beyond graphene is limited to bottom-up synthesis or lithographic patterning. Here, in this study, a versatile and direct approach is introduced to exfoliate bulk van der Waals crystals as nanoribbons. Akin to the Scotch tape exfoliation method for producing monolayers, this technique provides convenient access to a wide range of nanoribbons derived from their corresponding bulk crystals, including MoS 2 , WS 2 , MoSe 2 , WSe 2 , MoTe 2 , WTe 2 , ReS 2 , and hBN. The nanoribbons are predominantly monolayer, single-crystalline, parallel-aligned, flat, and exhibit high aspect ratios. The role of confinement, strain, and edge configuration of these nanoribbons is observed in their electrical, magnetic, and optical properties. This versatile exfoliation technique provides a universal route for producing a variety of nanoribbon materials and supports the study of their fundamental properties and potential applications.

2D materials↗
DOE OSTI2023

Ultrasound and X-ray Cross-Characterization of a Graded Impedance Impactor used for Shock-Ramp Compression Experiments

Abstract In this work we perform ultrasound measurements on an impedance graded impactor made by tape casting magnesium, copper, and tungsten. We also destructively extract small representative samples from the part for complementary characterization with x-ray computed tomography. Combining the two data sets enables direct assignment of some of the measured ultrasound features to specific material characteristics identified by x-ray tomography. Our results demonstrate how ultrasound inspection, informed by x-ray computed tomography, can be used to identify sub-millimeter material amalgamations and spatial heterogeneities in this graded material.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The Addition of Boron to Melt-Spun Fe-6.5%Si Ribbons

Fe-6.5%Si has higher electrical resistivity, lower magnetocrystalline anisotropy, and lower magnetostriction than traditional Fe-3.2%Si silicon steel. The reduced iron losses of Fe-6.5%Si render it a highly favorable candidate for high-speed motors and transformers. However, large-scale production of wide Fe-6.5%Si tape by rapid solidification can be challenging mainly because of its high melting point. In this work, boron is alloyed to Fe-6.5%Si to reduce its melting temperature and interfacial energy to improve the alloy’s processability. Boron additions from 0.01 wt.% to 2.24 wt.% into Fe-6.5%Si and its effect on ribbon thickness, grain size, magnetic, and mechanical properties were studied. Further, minor boron alloying significantly changed the melt pool stability and wetting on the quench wheel and in turn increased the quench rate with minimum impact on the magnetic saturation and ductility. Boron addition of < 0.06 wt.% was also found beneficial to the magnetic property of the alloy by lowering both its hysteresis and eddy current losses.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Transforming nanoscale VO 2 (B) into a scalable sodium-ion electrode

The intermittent nature of renewable energies requires highly reliable grid-level energy storage approaches. A critical consideration in developing this technology is the areal capacity which determines battery performance and influences the cost of battery technology. Of related importance is finding new ways of developing scalable electrodes. In recent years, three-dimensional (3D) printing of conductive scaffolds has emerged as an alternative to overcome the scalability limitations of commercial tape cast electrodes. The research carried out in the current study demonstrates a successful scalability pathway for nanoscale VO 2 (B), a desirable cathode for sodium-ion batteries which has a nano-flower morphology with a crystallite size < 20 nm. By electrodepositing VO 2 (B) onto a graphene aerogel scaffold, we were able to achieve mass loading of over 100 mg·cm −2 and still possess an areal capacity of 10 mAh·cm −2 at a current density of 5 mA·cm −2 . Moreover, after 1000 cycles, these electrodes retained 75% to 80% of their initial capacity. Even at high loading levels, the electrodeposited VO 2 (B) exhibits pseudocapacitive material signatures such as a box-like voltammetry response, linear galvanostatic response, and no phase change upon lithiation. The scalability of the VO 2 (B) electrode is demonstrated in a series of experiments which show the areal capacity to scale upon increase in both mass loading and electrode thickness, with only small changes in specific capacity. Furthermore, this study establishes that nanoscale materials can be scaled up to achieve thick electrodes without compromising their electrochemical properties.

additive manufacturing↗
DOE OSTI2025

dCache: The Storage System of Choice for Data-Intensive Applications

The ever-increasing volumes of data produced by modern scientific facilities like EuXFEL and LHC put significant stress on data management infrastructure operated by laboratories and research centers. The challenges to be addressed span the entire data life cycle, from ingest and efficient data analysis to long-term preservation, typically involving large tape libraries. dCache, a storage system developed in collaboration between the Deutsches Elektronen-Synchrotron (DESY), Fermi National Accelerator Laboratory, and Nordic e-Infrastructure Collaboration (NeIC), is designed to manage a large number of disk servers and to facilitate transparent data migration to and from archival storage. Its multifaceted approach offers a unified method to support a variety of scientific use cases with the same storage infrastructure, including high-throughput data ingest, data sharing over wide area networks, efficient access from HPC clusters, and long-term data preservation on tertiary storage. Initially developed for high energy physics (HEP) experiments, dCache is now used by various scientific communities, including astrophysics, biomedical research, and life sciences, each having specific requirements. This paper presents architecture, deployment strategies, performance and scalability enhancements, and recent advancements in dCache addressing the needs of scientific communities. Finally, we touch on the development and release process, ensuring the software’s high quality.

DCache↗
DOE OSTI2022

Spray coating for washout tooling by binder jet additive manufacturing

We report washout tooling is a process in which a removable mold or fixture is disintegrated using a solvent. Binder Jet (BJ) additive manufacturing holds promise for creating customized washout molds from common materials. BJ-based washout tooling provides an advanced strategy in manufacturing fiber-reinforced composites (FRCs), especially for customized hollow FRCs. However, washout tools formed by BJ require an impermeable barrier between the porous tooling surface and the parts laid up on the surface to prevent the resin from infiltrating the tooling surface and bonding the tool to the FRC. The conventional method for preventing resin migration into the washout mold from the FRC is winding Teflon® tape over the entire surface, which is labor-intensive and very difficult to deploy for specific geometries. Here, we report the development of a polymer spray coating method to seal the tooling surface and prevent resin infiltration without affecting the washout properties needed for sacrificial tooling. Two water-soluble polymers, poly(sodium 4-styrenesulfonate) (PSS–Na) and poly(vinylsulfonic acid, sodium salt) (PVS–Na), were investigated for spray coating. PVS-Na maintained tighter geometric tolerances and provided excellent thermal stability with the onset of decomposition at 320 °C and glass transition temperature of 280 °C. Spray coating with PVS-Na streamlines the process of forming a protective layer for the washout molds by BJ, reduces migration of the resins from the FRC, and significantly improves the production efficiency of complex washout tools.

42 ENGINEERING↗
DOE OSTI2026

Dynamic modeling of heat pipe integrated thermal battery latent heat storage system experiment validation

A heat pipe integrated thermal battery system has been constructed to investigate a high-temperature latent heat thermal energy storage technology that takes advantage of near isothermal operation of latent heat storage and heat pipes to potentially enable high-energy isothermal heat storage. A dynamic model constructed in Modelica has been validated, showing errors between 2.5 °C–39.7 °C across 10-h to 47-h simulations against experiment results, showing good prediction capability of experiment output, especially against phase change time. Model calibrations showing vessel heat-up capability of 3 kW and heat pipes combining to provide 600 W each during experiment operation validate experiment circumstances including reduced material loading and reduced power capability. The experiment configuration uses an Al-Mg-Zn eutectic metal as the storage material, heated via heat tape wrapped around the vessel and guide tubes to bring the system to operation range (>400 °C) and to simulate charging heat exchange, respectively, with heat rejection occurring through the surfaces of the material and facilitated via guide tubes with less insulation wrapping. The model is available in the open-source repository HYBRID on Github.

25 - ENERGY STORAGE↗
DOE OSTI2021

Conceptual design of HTS magnets for fusion nuclear science facility

Second-generation high temperature superconductors (HTS) are available for producing >20 T at the magnet bore compared to 13–16 T for lower temperature superconducting (LTS) toroidal field magnets proposed in recent fusion energy systems studies (FESS) of Fusion Nuclear Science Facility (FNSF). HTS may enable higher fusion power density and smaller device size. High current density cables of multi-layered REBCO tapes have achieved >10 kA at 4–20 K operation in short sample tests for fusion. High current density cables are required for engineering design of FNSF to allow space for interior plasma components. High current density HTS magnets are particularly attractive in reducing the size of a fusion device, beneficial for compact tokamaks, due to their space constraints. Successful HTS magnet development may enable the design of smaller and cheaper fusion pilot plants with a mission of demonstrating net electricity. It may also offer significant cost and performance advantages in non-fusion applicants such as nuclear magnetic resonance (NMR) and magnetic resonance imaging (MRI). Furthermore, we developed HTS magnet design concepts for a compact FNSF radial build in order to define the coil size, winding pack mechanical loading and engineering requirements. Partnering with vendors in the US, PPPL is also testing high current cable prototypes aiming at enabling low cost cable technology toward 100 A/mm 2 engineering current density over the winding pack desired in high field model coil development for compact fusion pilot plants.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗