SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Physical and thermal properties of structural reinforced plastic materials at cryogenic temperatures
Three different types of maneuvers were designed to separately quantify pitch rate and angle of attack rate contributions to the nondimensional aerodynamic pitching moment coefficient. These maneuvers combined pilot inputs and automatic multisine excitations, and were own with the subscale T-2 and Bat-4 airplanes using the NASA AirSTAR flight test facility. Stability and control derivatives, in particular C(sub mq) and C(sub m alpha(.)) were accurately estimated from the flight test data. These maneuvers can be performed with many types of aircraft, and the results can be used to increase simulation prediction fidelity and facilitate more accurate comparisons with wind tunnel experiments or numerical investigations.
An investigation has been conducted to determine the influence of aspect ratio, boundary-layer control by means of slots and porous surfaces, Reynolds number, and tunnel end-wall condition upon the performance of airfoils in cascades. A representative compressor-blade section (the NACA 65-(12)(10) of aspect ratios of 1, 2, and 4 has been tested at low speeds in cascades with solid and with porous side walls. Two-dimensional flow was established in porous-wall cascades of each of the three aspect ratios tested; the flow was not two-dimensional in any of the solid-wall cascades. Turbine-blade sections of aspect ratio 0.83 were tested in cascades with solid and porous side walls and blade sections of aspect ratio 3.33 were tested in cascades with solid wall. No particular advantage was observed in the use of porous walls for the turbine cascades tested.
Ames Research Center is developing the technology for turbine-powered jet engine simulators so that airframe/propulsion system interactions on V/STOL fighter aircraft and other highly integrated configurations can be studied. This paper describes the status of the compact multimission aircraft propulsion simulator (CMAPS) technology. Three CMAPS units have accumulated a total of 340 hr during approximately 1-1/2 yr of static and wind-tunnel testing. A wind-tunnel test of a twin-engine CMAPS-equipped close-coupled canard-wing V/STOL model configuration with nonaxisymmetric nozzles was recently completed. During this test approximately 140 total hours were logged on two CMAPS units, indicating that the rotating machinery is reliable and that the CMAPS and associated control system provide a usable test tool. However, additional development is required to correct a drive manifold O-ring problem that limits the engine-pressure-ratio (EPR) to approximately 3.5.
A method is described for measuring the dynamic stability derivatives of a model airplane in a wind tunnel. The characteristic features of this system are that single-degree-of-freedom oscillations were used to obtain combinations of rolling, yawing and pitching motions; that the oscillations were excited and controlled by velocity feedback which permitted operation under conditions unfavorable for more conventional types of oscillatory testing; and that data processing was greatly simplified by using analog computer elements in the strain-gage circuitry. A small number of experimental data are included to illustrate the general scope of results obtainable with this system.
Techniques for the measurement of subsonic dynamic stability derivatives of blunt-body re-entry capsules are being developed using a Magnetic Suspension and Balance System at NASA Langley Research Center. The measured aerodynamics of a 45-degree sphere-cone similar to configurations being considered for Mars Sample Return Earth Entry Vehicle are reported. A novel test method has been developed where forced oscillatory translation of a test article is used to excite yaw attitude oscillations. The forced motion is then halted to observe free-to-oscillate behavior of the test article. Parameter identification methods are used to extract drag as well as static and dynamic yawing moment stability characteristics from the measured forces and observed attitude histories. This combination of forced excitation followed by free-to-oscillate dynamics is a repeatable method to produce test article attitude histories that can be used to measure aerodynamic characteristics.
Techniques for the measurement of subsonic dynamic stability derivatives of blunt-body re-entry capsules are being developed using a Magnetic Suspension and Balance System at NASA Langley Research Center. The measured aerodynamics of a 45-degree sphere-cone similar to configurations being considered for Mars Sample Return Earth Entry Vehicle are reported. A novel test method has been developed where forced oscillatory translation of a test article is used to excite yaw attitude oscillations. The forced motion is then halted to observe free-to-oscillate behavior of the test article. Parameter identification methods are used to extract drag as well as static and dynamic yawing moment stability characteristics from the measured forces and observed attitude histories. This combination of forced excitation followed by free-to-oscillate dynamics is a repeatable method to produce test article attitude histories that can be used to measure aerodynamic characteristics.
A multichannel on-line RMS data acquisition and reduction system has been developed using commercial RMS computing modules and a programmable calculator. Details of this system, which has the capability of acquiring 96 channels of RMS data and computing and printing desired parameters in near real-time, are presented. In addition, raw data can be recorded at a much higher rate for computation and printing later. Results are presented showing the benefits of this system in 'sweep' tests where one parameter such as Mach number or angle of attack is slowly varied with time.
Variation in constraint through the thickness of a specimen effects the cyclic crack-tip-opening displacement (DELTA CTOD). DELTA CTOD is a valuable measure of crack growth behavior, indicating closure development, constraint variations and load history effects. Fatigue loading with a continual load reduction was used to simulate the load history associated with fatigue crack growth threshold measurements. The constraint effect on the estimated DELTA CTOD is studied by carrying out three-dimensional elastic-plastic finite element simulations. The analysis involves numerical simulation of different standard fatigue threshold test schemes to determine how each test scheme affects DELTA CTOD. The American Society for Testing and Materials (ASTM) prescribes standard load reduction procedures for threshold testing using either the constant stress ratio (R) or constant maximum stress intensity (K(sub max)) methods. Different specimen types defined in the standard, namely the compact tension, C(T), and middle cracked tension, M(T), specimens were used in this simulation. The threshold simulations were conducted with different initial K(sub max) values to study its effect on estimated DELTA CTOD. During each simulation, the DELTA CTOD was estimated at every load increment during the load reduction procedure. Previous numerical simulation results indicate that the constant R load reduction method generates a plastic wake resulting in remote crack closure during unloading. Upon reloading, this remote contact location was observed to remain in contact well after the crack tip was fully open. The final region to open is located at the point at which the load reduction was initiated and at the free surface of the specimen. However, simulations carried out using the constant Kmax load reduction procedure did not indicate remote crack closure. Previous analysis results using various starting K(sub max) values and different load reduction rates have indicated DELTA CTOD is independent of specimen size. A study of the effect of specimen thickness and geometry on the measured DELTA CTOD for various load reduction procedures and its implication in the estimation of fatigue crack growth threshold values is discussed.
Spacecraft photovoltaic arrays (PVA's) must be carefully handled during ground integration processing and transportation to the launch site. Care is exercised to avoid damage that could degrade on-orbit electrical performance. Because of this damage risk, however, PVA's are typically deployed and illuminated with a light source so performance characteristics can be measured prior to launch. For large-area arrays, such as the Mir Cooperative Solar Array (2.7- by 18-m) and the International Space Station PVA blankets (4.6- by 31.7-m), this integrity check becomes resource intensive. Large test support structures are needed to offload the array during deployment in 1g, and large-aperture illumination equipment is required to uniformly illuminate array panels. Significant program time, funds, and manpower must be allocated for this kind of test program. Alternatively, launch site electrical performance tests can be bypassed with an attendant increase in risk.
Experimental studies to determine the 140-deg spherically-blunted cone configuration single degree-of-freedom damping derivative included model sting interference effects at M = 1.76 to 3.0. Minimal sting influences are noted with sting/model diameter ratios of 0.183 and effective sting lengths of 3.55 of the reference length. Increasing the ratio of sting diameter to reference length to 0.53 influences damping considerably at angles of attack from 0 to 3 deg at all Reynolds numbers but shows little or no effect at higher angles. Free-flight model wake geometries (wake neck position and size) correlate well with those from captive model tests with the small diameter sting; this adds confidence to obtaining damping derivatives through captive model testing. The damping characteristics of an early Viking configuration obtained on 11.23 and 4.35% scale models using forced and free oscillation test methods, respectively, in two different test facilities are compared. The agreement is quite good under test conditions.
In mid 2003, NASA will launch identical spacecraft to deliver two large rovers to the Martian surface. As with the successful Mars Pathfinder (MPF) mission, the MER spacecraft will use an airbag landing system to safely deliver its payload.
A novel, efficient air data calibration method is proposed for aircraft with limited envelopes. This method uses output-error optimization on three-dimensional inertial velocities to estimate calibration and wind parameters. Calibration parameters are based on assumed calibration models for static pressure, angle of attack, and flank angle. Estimated wind parameters are the north, east, and down components. The only assumptions needed for this method are that the inertial velocities and Euler angles are accurate, the calibration models are correct, and that the steady-state component of wind is constant throughout the maneuver. A two-minute maneuver was designed to excite the aircraft over the range of air data calibration parameters and de-correlate the angle-of-attack bias from the vertical component of wind. Simulation of the X-48B (The Boeing Company, Chicago, Illinois) aircraft was used to validate the method, ultimately using data derived from wind-tunnel testing to simulate the un-calibrated air data measurements. Results from the simulation were accurate and robust to turbulence levels comparable to those observed in flight. Future experiments are planned to evaluate the proposed air data calibration in a flight environment.
Techniques used in the prediction of spacecraft contamination for the Galileo Jupiter Orbiter and in the determination of the effects of such contamination are presented. Following a quick-look assessment of the contributions of ground-based initial contaminant loading, launch vehicle interface effects, vacuum-exposed outgassing deposition and attitude control thruster impingement and venting to the spacecraft contamination burden, the evaluations centered on the effects of the attitude control thruster on the scan platform optics, including calculations of thruster flowfields and a high-fidelity computer simulation of contaminant distribution. The evaluations revealed a considerable problem with thruster contamination, which could be solved by the use of a thrust shield and the avoidance of thruster operation at certain scan platform orientations. The effects of the various possible contaminants on spacecraft thermal and optical system performances were also investigated in studies of the optical transmittance of deposited monomethyl hydrazine nitrate, vacuum optical degradation due to contaminant outgassing and re-emission outgassing, and an operational satellite contaminant monitor on the NOAA-C satellite. It is concluded that with a good evaluation and testing program, contamination control may become a necessary portion of system design procedures, and recommendations for the implementation of various practices and tests to minimize contamination effects are presented.
Explore the source record for details and available documents.
DOT /Driver-Displacement Oriented Transducer/, applicable to both lap shear type application and honeycomb sandwich structures, measures the displacement of the honeycomb composite face sheet. It incorporates an electromagnetic driver and a displacement measuring system into a single unit to provide noncontact bond strength measurements.
High temperature magnetic analysis of metallurgical structure of high strength steels and composites, including phase transformation and matrix grain structure
Explore the source record for details and available documents.