Search NASA⌕ Search

SEARCH · Search NASA

Results for “Test Techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Dynamic Stability Test Technique for Blunt Bodies in a Magnetic Suspension and Balance System

Techniques for the measurement of subsonic dynamic stability derivatives of blunt-body re-entry capsules are being developed using a Magnetic Suspension and Balance System at NASA Langley Research Center. The measured aerodynamics of a 45-degree sphere-cone similar to configurations being considered for Mars Sample Return Earth Entry Vehicle are reported. A novel test method has been developed where forced oscillatory translation of a test article is used to excite yaw attitude oscillations. The forced motion is then halted to observe free-to-oscillate behavior of the test article. Parameter identification methods are used to extract drag as well as static and dynamic yawing moment stability characteristics from the measured forces and observed attitude histories. This combination of forced excitation followed by free-to-oscillate dynamics is a repeatable method to produce test article attitude histories that can be used to measure aerodynamic characteristics.

Entry Systems Modeling↗
NASA NTRS1974

A fluctuating surface pressure test technique utilizing Mach number sweeps at transonic speeds

A multichannel on-line RMS data acquisition and reduction system has been developed using commercial RMS computing modules and a programmable calculator. Details of this system, which has the capability of acquiring 96 channels of RMS data and computing and printing desired parameters in near real-time, are presented. In addition, raw data can be recorded at a much higher rate for computation and printing later. Results are presented showing the benefits of this system in 'sweep' tests where one parameter such as Mach number or angle of attack is slowly varied with time.

Hanly, R. D.↗
NASA NTRS2007

Three Dimensional Constraint Effects on the Estimated (Delta)CTOD during the Numerical Simulation of Different Fatigue Threshold Testing Techniques

Variation in constraint through the thickness of a specimen effects the cyclic crack-tip-opening displacement (DELTA CTOD). DELTA CTOD is a valuable measure of crack growth behavior, indicating closure development, constraint variations and load history effects. Fatigue loading with a continual load reduction was used to simulate the load history associated with fatigue crack growth threshold measurements. The constraint effect on the estimated DELTA CTOD is studied by carrying out three-dimensional elastic-plastic finite element simulations. The analysis involves numerical simulation of different standard fatigue threshold test schemes to determine how each test scheme affects DELTA CTOD. The American Society for Testing and Materials (ASTM) prescribes standard load reduction procedures for threshold testing using either the constant stress ratio (R) or constant maximum stress intensity (K(sub max)) methods. Different specimen types defined in the standard, namely the compact tension, C(T), and middle cracked tension, M(T), specimens were used in this simulation. The threshold simulations were conducted with different initial K(sub max) values to study its effect on estimated DELTA CTOD. During each simulation, the DELTA CTOD was estimated at every load increment during the load reduction procedure. Previous numerical simulation results indicate that the constant R load reduction method generates a plastic wake resulting in remote crack closure during unloading. Upon reloading, this remote contact location was observed to remain in contact well after the crack tip was fully open. The final region to open is located at the point at which the load reduction was initiated and at the free surface of the specimen. However, simulations carried out using the constant Kmax load reduction procedure did not indicate remote crack closure. Previous analysis results using various starting K(sub max) values and different load reduction rates have indicated DELTA CTOD is independent of specimen size. A study of the effect of specimen thickness and geometry on the measured DELTA CTOD for various load reduction procedures and its implication in the estimation of fatigue crack growth threshold values is discussed.

Seshadri, Banavara R.↗
NASA NTRS1998

Dark Forward Electrical Test Techniques Developed for Large-Area Photovoltaic Arrays

Spacecraft photovoltaic arrays (PVA's) must be carefully handled during ground integration processing and transportation to the launch site. Care is exercised to avoid damage that could degrade on-orbit electrical performance. Because of this damage risk, however, PVA's are typically deployed and illuminated with a light source so performance characteristics can be measured prior to launch. For large-area arrays, such as the Mir Cooperative Solar Array (2.7- by 18-m) and the International Space Station PVA blankets (4.6- by 31.7-m), this integrity check becomes resource intensive. Large test support structures are needed to offload the array during deployment in 1g, and large-aperture illumination equipment is required to uniformly illuminate array panels. Significant program time, funds, and manpower must be allocated for this kind of test program. Alternatively, launch site electrical performance tests can be bypassed with an attendant increase in risk.

Kerslake, Thomas W.↗
NASA NTRS1972

Viking configuration pitch damping derivatives as influenced by support interference and test technique at transonic and supersonic speeds.

Experimental studies to determine the 140-deg spherically-blunted cone configuration single degree-of-freedom damping derivative included model sting interference effects at M = 1.76 to 3.0. Minimal sting influences are noted with sting/model diameter ratios of 0.183 and effective sting lengths of 3.55 of the reference length. Increasing the ratio of sting diameter to reference length to 0.53 influences damping considerably at angles of attack from 0 to 3 deg at all Reynolds numbers but shows little or no effect at higher angles. Free-flight model wake geometries (wake neck position and size) correlate well with those from captive model tests with the small diameter sting; this adds confidence to obtaining damping derivatives through captive model testing. The damping characteristics of an early Viking configuration obtained on 11.23 and 4.35% scale models using forced and free oscillation test methods, respectively, in two different test facilities are compared. The agreement is quite good under test conditions.

Steinberg, S.↗
NASA NTRS2012

A Full-Envelope Air Data Calibration and Three-Dimensional Wind Estimation Method Using Global Output-Error Optimization and Flight-Test Techniques

A novel, efficient air data calibration method is proposed for aircraft with limited envelopes. This method uses output-error optimization on three-dimensional inertial velocities to estimate calibration and wind parameters. Calibration parameters are based on assumed calibration models for static pressure, angle of attack, and flank angle. Estimated wind parameters are the north, east, and down components. The only assumptions needed for this method are that the inertial velocities and Euler angles are accurate, the calibration models are correct, and that the steady-state component of wind is constant throughout the maneuver. A two-minute maneuver was designed to excite the aircraft over the range of air data calibration parameters and de-correlate the angle-of-attack bias from the vertical component of wind. Simulation of the X-48B (The Boeing Company, Chicago, Illinois) aircraft was used to validate the method, ultimately using data derived from wind-tunnel testing to simulate the un-calibrated air data measurements. Results from the simulation were accurate and robust to turbulence levels comparable to those observed in flight. Future experiments are planned to evaluate the proposed air data calibration in a flight environment.

Taylor, Brian R.↗
NASA NTRS1981

Spacecraft contamination prediction and testing techniques

Techniques used in the prediction of spacecraft contamination for the Galileo Jupiter Orbiter and in the determination of the effects of such contamination are presented. Following a quick-look assessment of the contributions of ground-based initial contaminant loading, launch vehicle interface effects, vacuum-exposed outgassing deposition and attitude control thruster impingement and venting to the spacecraft contamination burden, the evaluations centered on the effects of the attitude control thruster on the scan platform optics, including calculations of thruster flowfields and a high-fidelity computer simulation of contaminant distribution. The evaluations revealed a considerable problem with thruster contamination, which could be solved by the use of a thrust shield and the avoidance of thruster operation at certain scan platform orientations. The effects of the various possible contaminants on spacecraft thermal and optical system performances were also investigated in studies of the optical transmittance of deposited monomethyl hydrazine nitrate, vacuum optical degradation due to contaminant outgassing and re-emission outgassing, and an operational satellite contaminant monitor on the NOAA-C satellite. It is concluded that with a good evaluation and testing program, contamination control may become a necessary portion of system design procedures, and recommendations for the implementation of various practices and tests to minimize contamination effects are presented.

Jeffery, J. A.↗
NASA NTRS1967

Nondestructive testing techniques used in analysis of honeycomb structure bond strength

DOT /Driver-Displacement Oriented Transducer/, applicable to both lap shear type application and honeycomb sandwich structures, measures the displacement of the honeycomb composite face sheet. It incorporates an electromagnetic driver and a displacement measuring system into a single unit to provide noncontact bond strength measurements.

Erdman, D. C.↗
NASA NTRS1972

Evaluation of nondestructive testing techniques for the space shuttle nonmetallic thermal protection system

A program was conducted to evaluate nondestructive analysis techniques for the detection of defects in rigidized surface insulation (a candidate material for the Space Shuttle thermal protection system). Uncoated, coated, and coated and bonded samples with internal defects (voids, cracks, delaminations, density variations, and moisture content), coating defects (holes, cracks, thickness variations, and loss of adhesion), and bondline defects (voids and unbonds) were inspected by X-ray radiography, acoustic, microwave, high-frequency ultrasonic, beta backscatter, thermal, holographic, and visual techniques. The detectability of each type of defect was determined for each technique (when applicable). A possible relationship between microwave reflection measurements (or X-ray-radiography density measurements) and the tensile strength was established. A possible approach for in-process inspection using a combination of X-ray radiography, acoustic, microwave, and holographic techniques was recommended.

Tiede, D. A.↗
NASA NTRS1979

An impulse test technique with application to acoustic measurements

A method has been presented for measuring the acoustic properties of an absorbent material and a duct/nozzle system (with or without airflow) using a high voltage spark discharge as an impulse source of sound. The cross-spectra of the incident, reflected and transmitted acoustic pressure transients are analyzed by way of a FFT digital processor in the form of complex transfer functions. These transfer functions have a direct relationship to the termination impedance and radiation directivity. The impulse method has been justified by comparisons, with data obtained from existing methods (both experimental and theoretical), that show excellent agreement. Reflection coefficients and radiation impedances of various duct-nozzle systems and their associated far-field directivities are also presented as some of the applications of the impulse technique.

Salikuddin, M.↗
NASA NTRS1981

Irrigated lands assessment for water management: Technique test

A procedure for estimating irrigated land using full frame LANDSAT imagery was demonstrated. Relatively inexpensive interpretation of multidate LANDSAT photographic enlargements was used to produce a map of irrigated land in California. The LANDSAT and ground maps were then linked by regression equations to enable precise estimation of irrigated land area by county, basin, and statewide. Land irrigated at least once in California in 1979 was estimated to be 9.86 million acres, with an expected error of less than 1.75% at the 99% level of confidence. To achieve the same level of error with a ground-only sample would have required 3 to 5 times as many ground sample units statewide. A procedure for relatively inexpensive computer classification of LANDSAT digital data to irrigated land categories was also developed. This procedure is based on ratios of MSS band 7 and 5, and gave good results for several counties in the Central Valley.

Wall, S. L.↗