Search NASA⌕ Search

SEARCH · Search NASA

Results for “Thermodynamic systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Using X-ray radiography to study oxygen flow in a proton exchange membrane electrolyzer operating under balanced pressure conditions

Of the various water electrolyzer technologies, the proton exchange membrane electrolyzer (PEMWE) is one of the best solutions for producing clean hydrogen without releasing CO 2 . In order to allow for widespread use of clean hydrogen, it is necessary to decrease its cost, which is intrinsically related to system operation. Current PEMWE plants operate in differential mode, directly pressurizing hydrogen and benefiting from thermodynamic compression, which increases overall system efficiency. However, high differential pressure above 30 bar can cause membrane stress, resulting in membrane creeping and failure. Pressurizing the water and operating at balanced pressure allows hydrogen to be produced at higher pressures while preserving the integrity of the membrane and porous layers. Nevertheless, the impact of pressurizing water on PEMWE performance must be better understood to maximize performance under balanced pressure conditions. Here, this study examined the impact of water pressure on two-phase flow. A high-pressure electrolyzer setup was developed to perform operando X-ray radiography and examine oxygen transport with high temporal resolution. The imaging segmentation process, developed to capture bubble properties in the channel, was applied to a specific experiment. The results clearly showed that as pressure increased up to 30 bars, the initial bubbly flow transitioned to slug flow, which led to channel saturation with oxygen. This work demonstrates that two-phase flow in an electrolyzer can be studied using X-ray radiography, which has the advantages of fast measurements and the ability to probe dense materials, such as those required for pressurized electrolyzers.

Balanced high pressure operation↗
DOE OSTI2024

A Machine Learning Bias Correction on Large–Scale Environment of High–Impact Weather Systems in E3SM Atmosphere Model

Large–scale dynamical and thermodynamical processes are common environmental drivers of high–impact weather systems causing extreme weather events. However, such large–scale environmental conditions often display systematic biases in climate simulations, posing challenges to evaluating high–impact weather systems and extreme weather events. In this paper, a machine learning (ML) approach was employed to bias correct the large–scale wind, temperature, and humidity simulated by the atmospheric component of the Energy Exascale Earth System Model (E3SM) at ~1° resolution. The usefulness of the ML approach for extreme weather analysis was demonstrated with a focus on three high–impact weather systems, including tropical cyclones (TCs), extratropical cyclones (ETCs), and atmospheric rivers (ARs). We show that the ML model can effectively reduce climate bias in large–scale wind, temperature, and humidity while preserving their responses to imposed climate change perturbations. The bias correction is found to directly improve water vapor transport associated with ARs, and representations of thermodynamical flows associated with ETCs. When the bias–corrected large–scale winds are used to drive a synthetic TC track forecast model over the Atlantic basin, the resulting TC track density agrees better with that of the TC track model driven by observed winds. In addition, the ML model insignificantly interferes with the mean climate change signals of large–scale storm environments as well as the occurrence and intensity of three weather systems. This study suggests that the proposed ML approach can be used to improve the downscaling of extreme weather events by providing more realistic large–scale storm environments simulated by low–resolution climate models.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Quantum Foundations of Classical Reversible Computing

The reversible computation paradigm aims to provide a new foundation for general classical digital computing that is capable of circumventing the thermodynamic limits to the energy efficiency of the conventional, non-reversible digital paradigm. However, to date, the essential rationale for, and analysis of, classical reversible computing (RC) has not yet been expressed in terms that leverage the modern formal methods of non-equilibrium quantum thermodynamics (NEQT). In this paper, we begin developing an NEQT-based foundation for the physics of reversible computing. We use the framework of Gorini-Kossakowski-Sudarshan-Lindblad dynamics (a.k.a. Lindbladians) with multiple asymptotic states, incorporating recent results from resource theory, full counting statistics and stochastic thermodynamics. Important conclusions include that, as expected: (1) Landauer’s Principle indeed sets a strict lower bound on entropy generation in traditional non-reversible architectures for deterministic computing machines when we account for the loss of correlations; and (2) implementations of the alternative reversible computation paradigm can potentially avoid such losses, and thereby circumvent the Landauer limit, potentially allowing the efficiency of future digital computing technologies to continue improving indefinitely. We also outline a research plan for identifying the fundamental minimum energy dissipation of reversible computing machines as a function of speed.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Temperature screening and cross-field impurity accumulation from a thermodynamic perspective

In a variety of different systems, high-Z ion species show a marked tendency to accumulate in regions of high plasma density. It has previously been suggested that the apparent universality of this behavior could be explained thermodynamically, in terms of the maximum-entropy state attainable when the system must obey an ambipolarity condition. Furthermore, the previous treatment did not allow for the possibility of temperature gradients. Here, tools from non-equilibrium (Onsager) thermodynamics are used to show that ambipolarity continues to play a key role in producing this behavior in the presence of temperature gradients, and to recover well-known temperature screening effects that appear in these cases.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Light-Induced Reorientation Transition in an Antiferromagnetic Semiconductor

Because of the lack of a net magnetic moment, antiferromagnets possess a unique robustness to external magnetic fields and are thus predicted to play an important role in future magnetic technologies. However, this robustness also makes them quite difficult to control, and the development of novel methods to manipulate these systems with external stimuli is a fundamental goal of antiferromagnetic spintronics. In this work, we report evidence for a metastable reorientation of the order parameter in an antiferromagnetic semiconductor triggered by an ultrafast quench of the equilibrium order via photoexcitation above the band gap. The metastable state forms less than 10 ps after the excitation pulse, and persists for longer than 150 ps before decaying to the ground state via thermal fluctuations. Importantly, this transition cannot be induced thermodynamically, and requires the system to be driven out of equilibrium. Broadly speaking, this phenomenology is ultimately the result of large magnetoelastic coupling in combination with a relatively low symmetry of the magnetic ground state. Since neither of these properties are particularly uncommon in magnetic materials, the observations presented here imply a generic path toward novel device technology enabled by ultrafast dynamics in antiferromagnets.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Thermal-Mechanical Analysis of an Additive Manufacturing Ceramic Heat Exchanger for High-Temperature Recuperator in a sCO2 Power System

Supercritical CO2 (sCO2) Brayton power cycle can be configured in a closed-loop power system and has a potentially high cycle efficiency. Compactness and high efficiency of a sCO2 power block make the sCO2 Brayton cycle a versatile power cycle in broad applications. While many heat sources are of sufficient intensity to produce high temperature working fluids to achieve high cycle efficiency, the thermal-mechanical stability of traditional materials (e.g., steels and nickel-based superalloys) used in construction of heat exchangers and turbine components limits the operating conditions and thus thermodynamic efficiency of the system. This effort seeks to establish the viability of ceramic heat exchanger technologies for the most extreme operating conditions envisioned for power generation and other high temperature processes. Heat exchangers constructed from ultra-high temperature ceramics, a class of extreme environment materials featuring melting points (Tmp.) above 3000 degrees C, is particularly appealing for sCO2 Brayton cycles given their ultra-low creep rates and very high retained strength at low homologous temperatures (i.e., T < 0.5 Tmp., or at least 1500 degrees C). To translate these materials properties to ultra-high temperature heat exchangers, innovations are required in ceramic manufacturing techniques to realize the complex architectures featured in compact heat exchangers with high power density. With appropriate processing, ZrB2-SiC based compositions can be sintered to near full density and shaped into complex topologies via ceramic additive manufacturing methods. This paper analyzes heat exchanger designs and explores thermal-mechanical implications of the operating environment. Thermal flow, heat transfer, and conjugate mechanical analyses provide insights into benefits and risks associated with the design approach.

additive manufacturing↗
DOE OSTI2023

Thermodynamic modeling of KCl-PrCl 3 and KCl-LiCl-PrCl 3 systems

Molten salt electrolysis can recover the actinides from spent nuclear fuels, and it involves a eutectic LiCl-KCl in molten form as an electrolyte. During reprocessing, the concentration of fission products such as La, Nd, Pr, etc., increases and affects the recovery efficiency of the electrolyte. In this work, thermodynamic modeling of KCl-PrCl 3 and KCl-LiCl-PrCl 3 systems was carried out using the CALPHAD (Calculation of Phase Diagrams) approach for the first time. The thermodynamic functions for the pure salts were taken from the SGTE (Scientific Group Thermodata Europe) Substances (SSUB) database. The experimental thermochemical and phase equilibria data available in the literature were used as input for the assessment of KCl-PrCl 3 and KCl-LiCl-PrCl 3 systems. The model parameters for the KCl-LiCl system were adjusted to include the new Gibbs energy descriptions for the pure salts. In addition, the sublattice model for the liquid phase in the LiCl-PrCl 3 system was modified and reassessed to ensure the model compatibility for higher-order extrapolation. There is a good agreement between the experimental and calculated thermochemical and phase diagram data for all the optimized constituent binaries and the ternary system. Furthermore, this work will be beneficial for determining the solubility limit of PrCl 3 in molten LiCl-KCl electrolytes and their thermodynamic properties for improving the efficiency of the pyrochemical process.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Dynamics of disordered mechanical systems with large connectivity, free probability theory, and quasi-Hermitian random matrices

Disordered mechanical systems with high connectivity represent a limit opposite to the more familiar case of disordered crystals. Individual ions in a crystal are subjected essentially to nearest-neighbor interactions. In contrast, the systems studied in this paper have all their degrees of freedom coupled to each other. Thus, the problem of linearized small oscillations of such systems involves two full positive-definite and non-commuting matrices, as opposed to the sparse matrices associated with disordered crystals. Consequently, the familiar methods for determining the averaged vibrational spectra of disordered crystals, introduced many years ago by Dyson and Schmidt, are inapplicable for highly connected disordered systems. In this paper we apply random matrix theory (RMT) to calculate the averaged vibrational spectra of such systems, in the limit of infinitely large system size. At the heart of our analysis lies a calculation of the average spectrum of the product of two positive definite random matrices by means of free probability theory techniques. We also show that this problem is intimately related with quasi-hermitian random matrix theory (QHRMT), which means that the ‘hamiltonian’ matrix is hermitian with respect to a non-trivial metric. This extends ordinary hermitian matrices, for which the metric is simply the unit matrix. The analytical results we obtain for the spectrum agree well with our numerical results. The latter also exhibit oscillations at the high-frequency band edge, which fit well the Airy kernel pattern. We also compute inverse participation ratios of the corresponding amplitude eigenvectors and demonstrate that they are all extended, in contrast with conventional disordered crystals. Finally, we compute the thermodynamic properties of the system from its spectrum of vibrations. In addition to matrix model analysis, we also study the vibrational spectra of various multi-segmented disordered pendula, as concrete realizations of highly connected mechanical systems. A universal feature of the density of vibration modes, common to both pendula and the matrix model, is that it tends to a non-zero constant at vanishing frequency.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

FY21 Status Report on the Molten Salt Thermal Properties Database (MSTDB) Development

This report describes the thermodynamic assessments for the ZrF 4 -BeF 2 , AlCl 3 -NaCl, AlCl3-KCl and the PuCl 3 -CsCl pseudo-binary subsystems. Calculation results are compared to the inputs used to optimize the adjustable model parameters. The data came from experimental studies reported in the open literature, from the MSR research community, and/or computational results generated within the NEAMS program and from collaborators. The models from the thermodynamic assessment of these salt systems are integrated into the MSTDB-TC (Molten Salt Thermal Properties Database-Thermochemical). A brief description of the companion MSTDB-TP (Molten Salt Thermal Properties Database-Thermophysical) is given along with an overview of the approach for predicting both thermodynamic and thermophysical property behavior of multicomponent systems.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Size Dependence of the Tetragonal to Orthorhombic Phase Transition of Ammonia Borane in Nanoconfinement

We have investigated the thermodynamic property modification of ammonia borane via nanoconfinement. Two different mesoporous silica scaffolds, SBA-15 and MCM-41, were used to confine ammonia borane. Using in situ Raman spectroscopy, we examined how pore size influences the phase transition temperature from tetragonal (I4mm) to orthorhombic (Pmn21) for ammonia borane. In bulk ammonia borane, the phase transition occurs at around 217 K; however, confinement in SBA-15 (with ~8 nm pore sizes) reduces this temperature to approximately 195 K, while confinement in MCM-41 (with pore sizes of 2.1–2.7 nm) further lowers it to below 90 K. This suppression of the phase transition as a function of pore size has not been previously studied using Raman spectroscopy. The stability of the I4mm phase at a much lower temperature can be interpreted by incorporating the surface energy terms to the overall free energy of the system in a simple thermodynamic model, which leads to a significant increase in the surface energy when transitioning from the tetragonal phase to the orthorhombic phase.

Najiba, Shah↗
DOE OSTI2024

Effect of Anoxic Iron Corrosion on WIPP Brine Geochemistry FY23 Final Report (U)

A 280-day study was completed to evaluate the effect of zero-valent iron (Fe 0 ) on the Waste Isolation Pilot Plant (WIPP) brine geochemistry under anticipated reducing conditions. Hydrogen (H 2 ) gas is expected to be present in the repository after closure due to the anoxic corrosion of a vast quantity of iron contained in the waste forms disposed at WIPP; therefore, a background argon atmosphere containing H 2 was chosen for this study. WIPP groundwater brine pH and E h will impact the mobility and fate of plutonium within the repository. Modeling and laboratory results for Castile WIPP brine indicate that equilibrium fa values relative to the standard hydrogen electrode (SHE) are 40 mV more reducing (i.e., more negative) than those for Salado WIPP brine (-480 mV vs. -440 mV, respectively) because of the higher pH of the Castile brine (pH 9 .3 for Castile vs. pH 8.8 for Salado). The E h and pH data were corrected for the effects of high ionic strength. The experimental results for both brines are consistent with thermodynamic predictions using OLI Systems' Mixed Solvent Electrolyte chemical equilibrium model. The measured and corrected pH and E h data from this study are provided in Table ES-I and Table ES-2, respectively. The experimental study, with four test conditions in triplicate, was performed in a dual glovebox with a nominally 3 vol.% H 2 in argon atmosphere (target H 2 range: 3 ± I vol.%). Simulants containing MgO only ( experimental control) and MgO+Fe 0 (WIPP base case) were prepared for both the Salado and Castile brines. MgO was included in all simulants to account for the use of bulk magnesium oxide in the WIPP repository. Fe 0 was included in some simulants to incorporate the effects of the anoxic corrosion of iron and in-situ hydrogen generation in the study. The brine compositions were developed by Sandia National Laboratory (SNL; Xiong, 2008) and have been used in previous WIPP evaluations. The test method (agitation, etc.) is partially based on ASTM D3987-12. Twelve rounds of periodic measurements of pH and E h were performed over the course of the study. Chemical analysis results for liquids and solids (ICP-MS, ICP-ES, IC Anion, TIC, SEM-EDX) are consistent with the pH, E h , and thermodynamic modeling results. This study included the following conditions that deviate from anticipated post-closure conditions following brine intrusion, but were selected to facilitate bench-scale testing to validate modeling of pH and E h for the post-closure WIP P repository: an anoxic glove box atmosphere containing ≤ 4 vol. % H 2 vs. substantially higher H 2 gas concentrations assumed in the WIPP Performance Assessment (PA); a significantly higher liquid-to-solid test ratio compared to the much lower phase ratio anticipated in the WIP P repository; agitation of the simulant bottles to maximize mass transfer; and finally the use of Fe 0 reagents having a much greater surface area than expected in the WIP P repository. Non-representative conditions were chosen for various reasons such as: to provide bounding conservative results, to provide a margin of safety for testing, or to facilitate simulant sub-sampling and analysis. In a parallel effort, aqueous electrolyte thermodynamic models were developed for the synthetic Salado and Castile brines to inform the experimental design, facilitate laboratory data interpretation, and allow extension of evaluations beyond the parameters tested. Thermodynamic modeling simulations including the MgO and Fe 0 additives that are directly relevant to the experimental measurements (e.g., pH calibration curve, ORP corrections) are included in this report. The measured fa of the simulants was close to the OLI model predictions for both brines and was largely controlled by the background H 2 partial pressure in the vapor phase as well as H 2 generated in situ in the aqueous phase by the Fe 0 corrosion. The H 2 gas-phase concentration tested and thermodynamically evaluated was much lower than is assumed in the WIPP PA; however, H 2 (g) concentrations significantly below this level are still predicted to result in very reducing conditions. In conclusion: • The experimental results are consistent with thermodynamic model predictions for fa, pH, and the effects of high ionic strength. • Evidence to date suggests that the H2 concentration in the glovebox atmosphere ultimately determined the final E h values of the simulants and resulted in highly reducing conditions. As a result, little difference was observed between the control simulants containing only MgO and the WIPP base-case simulants that contained MgO and Fe 0 . • This test methodology is recommended for future studies evaluating WIPP repository conditions. The methodology includes: (1) background H 2 in argon with agitation ( or could alternatively include in-situ-generated H 2 in sealed bottles); (2) carefully measured and corrected ORP data ( with much effort focused on allowing the probes to fully stabilize); and (3) ionic-strength-corrected pH data. Other best practices, such as simulant sparging/handling, ORP probe replacement, etc., should also be considered. • The coupling of experimental studies and thermodynamic modeling is also highly recommended because these methods inform and direct one another leading to greater confidence in and understanding of the results.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Investigation of aluminum nitrate as a set retarder of magnesium potassium phosphate cement: Mechanisms involved in diluted suspension

In this study, the influence of aluminum nitrate on the hydration process of magnesium potassium phosphate (MKP) cement was investigated experimentally and through thermodynamic modelling using diluted systems with Mg/PO{sub 4} molar ratio and water-to-cement ratio of 1 and 100 respectively. Three processes contributed to retard cement hydration: the acidic nature of aluminum nitrate which reduced the initial pH of the solution by two units, the early precipitation of a taranakite-like amorphous potassium aluminophosphate, which reduced the aqueous phosphate and potassium concentrations, and a salt effect due to the presence of soluble nitrate. Precipitation of potassium-containing magnesium phosphate hydrates, like Mg{sub 2}KH(PO{sub 4}){sub 2}⋅15H{sub 2}O and K-struvite, was prohibited, whereas precipitation of newberyite and cattiite was delayed. Furthermore, the modelled phase development with ongoing cement hydration agreed rather well with the experimental findings.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structure of a chaotic tangle of quantum vortices in turbulent superfluid liquids and in a Bose – Einstein condensate

Based on the theory of the thermodynamic equilibrium in a system of quantum vortices in superfluid liquids and in a Bose – Einstein condensate in the presence of a counterflow of normal and superfluid components, we investigate the structure of a chaotic tangle of quantum vortices in turbulent superfluid liquids. Using the characteristic functional method, the properties of hydrodynamic vortex filaments are examined. It is shown that the average curvature of the vortex lines is on the order of the intervortex distance, with the proportionality coefficient being independent of the counterflow velocity. It is found that the degree of anisotropy of the vortex loops does not depend on the applied counterflow velocity. The obtained results explain the origin of the anisotropy as well as the relationship between the curvature of the lines and the intervortex space and their dependence on the parameters of the problem. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Thermodynamic properties of ZrCl 4 with LiCl, NaCl, KCl, CsCl, MgCl 2 , and UCl 3 for molten salt reactor applications

Here, a set of self-consistent Gibbs energy functions has been developed to describe the thermochemical behavior of the major reactive fission product ZrCl 4 with key components in chloride molten salt reactors (MSRs): LiCl–ZrCl 4 , NaCl–ZrCl 4 , KCl–ZrCl 4 , CsCl–ZrCl 4 , MgCl 2 –ZrCl 4 and UCl 3 –ZrCl 4 . Low ZrCl 4 concentration phase equilibria most relevant to MSR applications have been confirmed via differential scanning calorimetry for NaCl–ZrCl 4 , and X-ray diffraction analysis performed on equilibrated samples of NaCl–ZrCl 4 , KCl–ZrCl 4 , MgCl 2 –ZrCl 4 , and UCl 3 –ZrCl 4 . Within the framework of the modified quasi-chemical model in the quadruplet approximation, extrapolations of pseudo-binary models were generated to represent KCl–MgCl 2 –ZrCl 4 , KCl–NaCl–ZrCl 4 , and MgCl 2 –NaCl–ZrCl 4 , which show agreement with phase equilibria data where available without the use of ternary interaction parameters. The optimized thermodynamic descriptions for these systems and others are available in the open-source compendium Molten Salt Thermal Properties Database – Thermochemical (MSTDB–TC).

CALPHAD↗
DOE OSTI2022

How Cooperatively Folding Are Homopolymer Molecular Knots?

Detailed thermodynamic analysis of complex systems with multiple stable configurational states allows for insight into the cooperativity of each individual transition. In this work, we derive a heat capacity decomposition comprising contributions from each individual configurational state, which together sum to a baseline heat capacity, and contributions from each state-to-state transition. We apply this analysis framework to a series of replica exchange molecular dynamics simulations of linear and 1-1 coarse-grained homo-oligomer models, which fold into stable, configurationally well-defined molecular knots, in order to better understand the parameters leading to stable and cooperative folding of these knots. We find that a stiff harmonic backbone bending angle potential is key to achieving knots with specific 3D structures. Tuning the backbone equilibrium angle in small increments yields a variety of knot topologies. Populations of different knotted states as a function of temperature can also be manipulated by tuning the backbone torsion stiffness or by adding side-chain beads. We find that sharp total heat capacity peaks for the homo-oligomer knots are largely due to a coil-to-globule transition rather than a cooperative knotting step. Furthermore, in some cases, the cooperativity of globule-to-knot and coil-to-globule transitions is comparable, suggesting that highly cooperative folding to knotted structures can be achieved by refining the model parameters or adding sequence specificity.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Integrated protonic ceramic electrochemical cell for sustainable energy economy using water-energy nexus framework

Reliance on fossil fuels will continue for the next decades even though there are global pushes away from it to mitigate the overarching climate challenge, most especially by its highest consumers and availability. While there is a hastening global shift away from fossil fuel, integrating its assets into this technology helps limit the risk and future losses of stranded assets and reduce the cost of investment in the new technologies. Moreover, the generation of electricity from intermittent renewable sources like solar and wind has witnessed a significant surge in recent years, leading to a pressing demand for practical energy storage systems. Electrical energy storage is anticipated to play a pivotal role in the future global energy system, facilitating load-leveling operations to support the greater integration of renewable and distributed generation. Reversible electrochemical cells (RECs) offer a promising option for addressing the fossil fuel assets integration and energy storage challenges through the interconversion between electrical and chemical energy and concurrent utilizing carbon emission. In their electrolysis mode, the RECs convert electricity into durable, storable, and portable valuable chemical fuels such as syngas and methane. Conversely, the produced chemical fuels can be used as reactants in the fuel cell mode to generate electricity on demand with minimal (hydrocarbons) or zero when H2 or NH3 is used emissions. However, a challenging goal for this type of technology remains to achieve optimal operation and high roundtrip efficiencies, which has hindered the deployment of previous electrochemical cells. This dissertation demonstrates how reversible protonic ceramic electrochemical cells (RePCECs) can be integrated with fossil fuel power plants and renewable energy sources as a potential energy storage system. In this work, integrated RePCEC systems are designed and examined using computational modeling at scales to determine appropriate system configurations and operating conditions that achieve high roundtrip efficiencies. Cell level design of the PCEC is the first approach, several cells are assembled for the stack level model that is integrated into combined cycle powerplant and solar photovoltaic for the system level model. After critical literature review, this answered the operational and integration research questions proposed to address these challenges. The designed systems perform two functions, utilizing captured CO2 and storing renewable energy through co-electrolysis of steam and CO2. The co-electrolysis reaction involves endothermic water electrolysis and exothermic methanation reaction. To enhance high roundtrip efficiency, there is a need for thermal balance and management in the electrolysis mode. This involves operating the RePCEC stack under conditions that favor methane production to balance out heat needed by water electrolysis, it crucial for the RePCEC system operation. Methanation is enhanced by low temperatures. Leveraging on fabricated BCZYYb-electrolyte RePCEC, the cell model designed revealed that the optimum temperature for methane production is 450℃ at atmospheric pressure. Thus, to achieve optimum system performance, operating in the temperature range 450-525℃ is recommended at the given configuration, combining between the optimum temperature for methane production and temperature for the optimum stack roundtrip efficiency. Configuration with carbon capture system and purge stream is the optimum configuration from the seven conceptualized and evaluated. The modeling outcomes include a thermodynamic examination of integrated RePCEC systems, calibration of cell and stack level models, and steady-state simulation and integration into a 600MW combined cycle power plant retrofitted with two two-stage membrane-based carbon capture system and a wastewater treatment and recovery unit. At 100% powerplant loading, the stack and system roundtrip efficiencies are 72% and 51.37% respectively. Adding a purge stream for produced hydrogen at the system downstream improves the efficiencies to 74 and 55.48% respectively. At atmospheric pressure and 525℃, the system model suggests that a stack roundtrip of 82% is achievable, and overall system efficiency increases by reducing the energy consumption by the balance of plant components for steam generation and storage. Economic analysis of the process gives levelized cost of methane as $2.24/MMBtu lower than the conventional production route that range between $3.46/MMBtu and $9.85/MMBtu. The lifecycle analysis shows that the global warming potential for the production of methane and hydrogen from the RePCEC system is 3.83 kg CO2 eq which is lower than 9.35 kg CO2 eq emission during steam methane reforming for hydrogen production. This answered both the environmental and economic concerns in the raised research question. The proposed RePCEC configuration and analysis carried out in this dissertation to address the surge in renewable energy and challenges with PCEC technology hold significant potential in achieving large-scale energy storage while simultaneously reducing carbon emissions. These advancements, coupled with suitable governmental policies and incentive programs, have the potential to economically disrupt the natural gas industries by using RePCEC systems for methane production, thereby making them more favorable for eventual implementation and commercialization.

25 ENERGY STORAGE↗
DOE OSTI2020

Computational thermodynamics and its applications

Thermodynamics is a science concerning the state of a system, whether it is stable, metastable or un- stable, when interacting with the surroundings. In this overview, fundamentals of thermodynamics are briefly reviewed through the combination of first and second laws of thermodynamics for open and nonequilibrium systems to demonstrate that the reversible equilibrium and irreversible nonequilibrium thermodynamics can be integrated to enhance the power and utilities of thermodynamics. The recent progresses in computational thermodynamics, the remaining challenges, and potential impacts in broad scientific fields are discussed here. It is shown that computational thermodynamics enables the modeling of thermodynamics of a state as a function of both external and internal variables and quantitative calculations of a broad range of properties of a multicomponent system in terms of first and second derivatives of energy, including not only equilibrium states when there are no driving forces for any internal processes and but also non-equilibrium states with driving forces for internal processes. Consequently, external constraints such as fixed strain and internal degree of freedoms such as ordering and defects can be described in a coherent framework and applied to materials design. Furthermore, two important but largely overlooked aspects in thermodynamics will be discussed, i.e. the rigorous application of statistical thermodynamics with the probability of configurations and their contributions to system properties, and the applications of second derivatives of energy with respect to either two extensive variables or two potentials or a mixture of them in terms of understanding and predicting emergent behaviors, critical phenomena, kinetic coefficients, and mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Conjugated Polyelectrolyte-Based Complex Fluids as Aqueous Exciton Transport Networks

The ability to assemble artificial systems that mimic aspects of natural light-harvesting functions is fascinating and attractive for materials design. Given the complexity of such a system, a simple design pathway is desirable. Here, we argue that associative phase separation of oppositely charged conjugated polyelectrolytes (CPEs) can provide such a path in an environmentally benign medium: water. We find that complexation between an exciton–donor and acceptor CPE leads to formation of a complex fluid. We interrogate exciton transfer from the donor to the acceptor CPE within the complex fluid and find that transfer is highly efficient. We also find that excess molecular ions can tune the modulus of the inter-CPE complex fluid. Even at high ion concentrations, CPEs remain complexed with significantly delocalized electronic wavefunctions. In conclusion, our work lays the rational foundation for complex, tunable aqueous light-harvesting systems via the intrinsic thermodynamics of associative phase separation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗