Search NASA⌕ Search

SEARCH · Search NASA

Results for “VIBRATIONAL FREQUENCY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Vibrational Spectrum of (CO)2 on Cu(100): Quantum Calculations with 18 Coupled Mode

We report calculations of the vibrational frequencies of CO dimer on Cu(100) using recently developed vibrational self-consistent field code. Eighteen modes are treated explicitly within three modes coupling representation. Nine symmetry distinct doublets are observed and the corresponding frequencies are computed. The thermally broadened spectrum of the CO-stretch fundamental is calculated at various temperatures. Both the temperature and coverage dependence of both the average CO-stretch frequency and the corresponding line-width are consistent with experimentally observed trends. The document contains no classified information International clearance is needed.

Dzegilenko, Fedor↗
NASA NTRS1992

Microgravity vibration isolation: Optimal preview and feedback control

In order to achieve adequate low-frequency vibration isolation for certain space experiments an active control is needed, due to inherent passive-isolator limitations. Proposed here are five possible state-space models for a one-dimensional vibration isolation system with a quadratic performance index. The five models are subsets of a general set of nonhomogeneous state space equations which includes disturbance terms. An optimal control is determined, using a differential equations approach, for this class of problems. This control is expressed in terms of constant, Linear Quadratic Regulator (LQR) feedback gains and constant feedforward (preview) gains. The gains can be easily determined numerically. They result in a robust controller and offers substantial improvements over a control that uses standard LQR feedback alone.

Hampton, R. D.↗
NASA NTRS2003

Experiments on Suppression of Thermocapillary Oscillations in Float-Zones by High-Frequency End-Wall Vibrations

Experiments to suppress thermocapillary oscillations using high-frequency vibrations were performed on float-zones. Such a float-zone is formed by melting one end of a vertically held sodium nitrate-barium nitrate crystal rod in contact with a hot surface at the top. In the experiments, when thermocapillary oscillation occurred, the bottom end of the rod was vibrated at a high frequency to generate fine ripples on the melt surface, driving a streaming flow in the opposite direction to that of the thermocapillary convection. It was observed that by generating a sufficiently strong streaming flow the thermocapillary flow can be offset enough such that the associated thermocapillarity oscillations can be quenched.

Anilkumar, A. V.↗
NASA NTRS2004

Experiments on Suppression of Thermocapillary Oscillations in Sodium Nitrate Floating Half-Zones by High-frequency End-wall Vibrations

Experiments to suppress thermocapillary oscillations using high-frequency vibrations were carried out in sodium nitrate floating half-zones. Such a half-zone is formed by melting one end of a vertically held sodium nitrate crystal rod in contact with a hot surface at the top. Thermocapillary convection occurs in the melt because of the temperature gradient at the free surface of the melt. In the experiments, when thermocapillary oscillations occurred, the bottom end of the crystal rod was vibrated at a high frequency to generate a streaming flow in a direction opposite to that of the thermocapillary convection. It is observed that, by generating a sufficiently strong streaming flow, the thermocapillary flow can be offset enough such that the associated thermocapillary oscillations can be quenched.

Anilkumar, A.↗
NASA NTRS2013

On the Use of Quartic Force Fields in Variational Calculations

The use of quartic force fields (QFFs) has been shown to be one of the most effective ways to efficiently compute vibrational frequencies for small molecules. In this paper we outline and discuss how the simple-internal or bond-length bond-angle (BLBA) coordinates can be transformed into Morse-cosine(-sine) coordinates which produce potential energy surfaces from QFFs that possess proper limiting behavior and can effectively describe the vibrational (or rovibrational) energy levels of an arbitrary molecular system. We investigate parameter scaling in the Morse coordinate, symmetry considerations, and examples of transformed QFFs making use of the MULTIMODE, TROVE, and VTET variational vibrational methods. Cases are referenced where variational computations coupled with transformed QFFs produce accuracies compared to experiment for fundamental frequencies on the order of 5 cm(exp −1) and often as good as 1 cm(exp −1).

quartic force field↗
NASA NTRS1976

Optimization of continuous one-dimensional structures under steady harmonic excitation

The paper examines some questions relating to the optimal design of continuous one-dimensional structures driven by harmonically oscillating loads. Optimal-control methods are applied to a cantilever bar driven sinusoidally by an axial force at its tip to illustrate the minimum-weight design of one-dimensional structures under dynamic excitation. Realistic constraints are imposed during the optimizations, including a maximum allowable stress amplitude at any point along the bar and a minimum cross-sectional area. It is shown that in the absence of damping, the design space may contain many disjoint feasible regions, and multiple optima can exist. Detailed solutions are obtained for continuous bars with an excitation frequency less than, and then greater than, the fundamental free-vibration frequency. It is found that above a certain excitation frequency, two or more arcs with different constraints characterize the optimal designs. It is concluded that when more than two different constrained arcs characterize the optimal solution, the continuum approach may be impractical, and finite-element approximations may offer the only alternative.

Johnson, E. H.↗
NASA NTRS1990

Limitations on vibration isolation for microgravity space experiments

The vibration-isolation limitations of spaceborne microgravity experiments are largely due to isolation-system volume restrictions. In the present one-degree-of-freedom representation of an experimental aircraft, assuming an ideal vibration actuator, wall motion is characterized as sinusoidal at a single frequency. The result is a kinematic representation which poses the problem of the minimum acceleration trajectory within a pair of moving walls; analysis then yields a simple condition under which a closed-form solution is available. The results obtained demonstrate that isolation from low-frequency vibration requires more interior space than is available for vibration isolation on manned orbiters.

Knospe, C.↗
NASA NTRS1985

Dynamic characteristics of statically determinate space-truss platforms

The geometry of a class of statically determinate platforms is developed and vibration frequencies determined. Such configurations would allow shape control by changing member lengths to be accomplished with small forces. An additional advantage of a statically determinate structure is being free of thermal stress under any temperature distribution. Frequency comparisons between statically determinate and more conventional redundant platforms are presented. Vibration of curved platforms that could be used as antenna concepts is also investigated. Alternate concepts incorporating the statically determinate design but having improved dynamic characteristics are suggested.

Anderson, M. S.↗
NASA NTRS1947

Vibration Survey of Blades in 19XB Axial-Flow Compressor: Dynamic Investigation - 2

Strain-gage measurements were taken under operating conditions from blades of various stages of the 19XB axial-flow compressor in an effort to determine the reason for failures in the seventh and tenth stages. First bending-mode vibrations were detected in the first five stages of the compressor caused by each integral multiple of rotor speed from three through ten. Lead-wire failures in the last five stages resulted in incomplete data. The dynamic-vibration frequencies at various rotor speeds were compared with statically measured frequencies analytically corrected for the influence of centrifugal force. Large increases in vibration ani~litude with increased pressure ratio were observed. During surging operation, blade vibrations were not present. The effects of pressure ratio and surge indicate the existence of aerodynamic excitation as the cause of the blade vibrations.

Meyer, Andre J., Jr.↗
NASA NTRS1973

Diagnostics of the technical condition of antifriction bearings

Shock pulse measurements that express the characteristic curves of rotational bearing resistance are used to diagnose possible deficiencies. Spectral analysis of frequency vibration tracings establishes probable causes for various anomalies in the geometric shape, surface frequency, contamination, etc.

Vitkute, A. E. Y.↗
NASA NTRS1991

Limitations and improvements of one-dimensional beam dynamics

The static and dynamic behavior limitations of 1D beam modeling are discussed, with a view to the prediction of high frequency vibrations. A methodology is suggested whereby the construction of 3D dispersion curves is followed by the incorporation of asymptotical considerations to calculate the lowest high-frequency branches of the long-wave vibrations, as well as some short-wave vibrations. A comparison of the two will then yield the constraints for the one-dimensional composite beam modeling of both dynamic and static applications.

Atilgan, Ali R.↗
NASA NTRS1993

The (FHCl)- molecular anion - Structural aspects, global surface, and vibrational eigenspectrum

State of the art ab initio electronic structure methods have been used to investigate the (FHCl)- molecular anion. It is proposed that the geometric structure and binding energies of the complex are r(e)(H-F) = 0.963 +/- 0.003 A, R(e)(H-Cl) = 1.925 +/- 0.015 A, and D0(HF + Cl(-)) = 21.8 +/- 0.4 kcal/mol. A Morokuma decomposition of the ion-molecular bonding give the following electrostatic, polarization, exchange repulsion, dispersion, and charge-transfer plus higher-order mixing components of the vibrationless complexation energy: -27.3, -5.2, +18.3, -4.5, and -5.0 kcal/mol, respectively. A couples cluster single and doubles global surface is constructed from 208 and 228 energy points for linear and bent configurations, respectively, these being fit to rms errors of only 3.9 and 9.3/cm, respectively, below 8000/cm. Converged J = 0 and J = 1 variational eigenstates of the (FHCl)- surface to near the HF + Cl(-) dissociation threshold are determined. The fundamental vibrational frequencies are found to be nu1 = 247/cm, nu2 = 876/cm, and nu3 = 2884/cm. The complete vibrational eigenspectrum is analyzed.

Klepeis, Neil E.↗
NASA NTRS1978

Effect of crack size on the natural frequencies of a cracked plate

Results are presented for a finite element modal analysis of a centrally cracked rectangular plate made of linearly elastic material. The objective is to assess the effect of crack size on the natural vibration frequencies of the cracked plate. Only the in-plane vibration modes are studied. The results presented are finite-element mesh-size dependent. Namely, shrinking the mesh size, especially in the crack tip region, would change the magnitudes of the natural frequencies, and the trends would be the same as shown in the present note.

Ko, W. L.↗
NASA NTRS1985

Deriving Strain Modes From Vibrational Tests

Measurements and theoretical analysis complement each other. Experimental acceleration and strain data used to calculate coefficients of low-frequency vibrational modes of object under test. An iterative comparison of experimental and calculated strains give modal model of improved accuracy that predicts strains under operating conditions. Method useful in fatigue life and reliability analyses of buildings, pumps, engines, vehicles, and other systems subject to vibrations and loud noises during operation.

Young, J. W.↗
NASA NTRS1975

Effects of control-stick parameters on tracking performance in a vibration environment

A set of manual control experiments was conducted to determine the effects of control stick parameters on tracking performance in a vibration environment. Primary experimental variables were stick design parameters, stick location, and presence or absence of vibration. Considerable effect on control activity suggests that stick design parameters will significantly influence overall performance in systems that respond at vibration frequencies. Stick location had no significant effect on either tracking or biodynamic performance measures. The vibration correlated component of tracking error was relatively small. A model based guide for the design of control sticks in a vibration environment is described. This model is based on the state variable model for pilot/vehicle systems. Effects of vibration are represented as additional model elements and by changes in pilot related parameters of the tracking model.

Levison, W. H.↗
NASA NTRS1976

Vibration characteristics of composite fan blades and comparison with measured data

The vibration characteristics of a composite fan blade for high-tip-speed applications were determined theoretically and the results compared with measured data. The theoretical results were obtained using a computerized capability consisting of NASTRAN coupled with composite mechanics by way of pre- and postprocessors. The predicted vibration frequencies and mode shapes were in reasonable agreement with the measured data. Theoretical results showed that different laminate configurations from the same composite system had only small effects on the blade frequency. However, the use of adhesively bonded titanium/beryllium laminar composites may improve considerably the blade vibration characteristics.

Chamis, C. C.↗