Search NASA⌕ Search

SEARCH · Search NASA

Results for “VTOL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Empirical expressions for estimating length and weight of axial-flow components of VTOL powerplants

Simplified equations are presented for estimating the length and weight of major powerplant components of VTOL aircraft. The equations were developed from correlations of lift and cruise engine data. Components involved include fan, fan duct, compressor, combustor, turbine, structure, and accessories. Comparisons of actual and calculated total engine weights are included for several representative engines.

Sagerser, D. A.↗
NASA NTRS1972

Design studies of lift fan engines suitable for use in civilian VTOL aircraft

Low pressure ratio fan engines are receiving increasing attention as a means to provide low speed lift for civilian VTOL transports. Two general types of fan lift engines that are being studied are integral fans and remote power fans. Preliminary engine design studies of both types of lift fan systems have been made. The paper summarizes a portion of the results of the engine design studies, including the crucial engine requirements, and some of the characteristics of the emerging engine designs of each type.

Roelke, R. J.↗
NASA NTRS1972

Fan and wing force data from wind tunnel investigation of a 0.38 meter (15 inch) diameter VTOL model lift fan installed in a two dimensional wing

Test data are presented for a 38-cm (15-in.) diameter, 1.28 pressure ratio model VTOL lift fan installed in a two-dimensional wing and tested in a 2.74-by 4.58-meter (9-by 15-ft)V/STOL wind tunnel. Tests were run with and without exit louvers over a wide range of crossflow velocities and wing angle of attack. Tests were also performed with annular-inlet vanes, inlet bell-mouth surface disconuities, and fences to induce fan windmilling. Data are presented on the axial force of the fan assembly and overall wing forces and moments as measured on force balances for various static and crossflow test conditions. Midspan wing surface pressure coefficient data are also given.

Yuska, J. A.↗
NASA NTRS1972

Static performance of a 13.97 cm (5.5 inch) diameter model VTOL lift fan

A tip-turbine-driven fan of the type currently being used in wind tunnel tests of VTOL lift fan models was tested. Values of thrust, weight flow, exit total and static pressure, exit swirl angle, and turbine temperature drop were measured as a function of fan speed for several inlet and exit configurations. A standard fan performance map was also obtained.

Lowe, W. H.↗
NASA NTRS1972

Effect of stabilization on VTOL aircraft in hovering flight

A motion simulator study was conducted to determine the effects of roll and pitch stabilization on the handling qualities and control power requirements of VTOL aircraft during hover and short-distance maneuvering flight. Three levels of stabilization complexity were compared: (1) no stabilization, (2) rate stabilization, and (3) attitude stabilization. Control sensitivities and stabilization gains were optimized prior to comparison. Results are presented to show how the optimum systems were determined and how they compared with each other at different levels of control power. Comparisons were made both in calm air and in the presence of roll disturbances. Results indicate the attitude-stabilized system provides the best handling qualities for the least amount of control power.

Greif, R. K.↗
NASA NTRS1972

Simulation study of the lift roll coupling problem for hovering VTOL aircraft

The effects of lift-roll coupling on the handling qualities of hovering VTOL aircraft using differential thrust for roll control were assessed in a piloted simulation study in the Ames six-degrees-of-freedom motion simulator. The configuration tested has three vertical thrust sources, one on the roll axis and two laterally displaced from the roll axis, with a thrust distribution of 25%/50%/25%. The outboard thrust sources were modulated to provide roll control whereas all three provided height control. Maximum thrust-to-weight ratio was varied together with a coupling parameter that combined roll-inertia, weight, and engine location. Results showed that handling qualities are affected not only by the occurrence of lift-roll coupling (dependent on both variables) but also by the severity of the coupling (dependent on the coupling parameter alone). However, the advantages of differential thrust for control can be retained with careful design.

Jacobsen, R. A.↗
NASA NTRS1972

Design studies of lift fan engines suitable for use in civilian VTOL aircraft.

Preliminary engine design studies have been made of two general types of low-pressure-ratio lift fan engines that are receiving increasing attention as a means to provide low-speed lift for large civilian VTOL transports. The two engine types are integral fans and remote powered fans. A portion of the results of these design studies is summarized, including the crucial engine requirements, and some of the characteristics of the emerging engine designs of each type.

Roelke, R. J.↗
NASA NTRS1972

A pilot's opinion - VTOL control design requirements for the instrument approach task.

This paper presents pilot opinion supported by test data concerning flight control and display concepts and control system design requirements for VTOL aircraft in the instrument approach task. Material presented is drawn from research flights in the following aircraft: Dornier DO-31, Short SC-1, LTV XC-142A, and Boeing-Vertol CH-46. The control system concepts and mechanizations employed in the above aircraft are discussed, and the effect of control system augmentation is shown on performance. Operational procedures required in the instrument approach task are described, with comments on need for automation and combining of control functions.

Patton, J. M., Jr.↗
NASA NTRS1973

Effect of rotor design tip seed on aerodynamic performance of a model VTOL lift fan under static and crossflow conditions

Results are presented for a wind tunnel investigation of three single VTOL lift fan stages designed for the same overall total pressure ratio at different rotor tip speeds. The stages were tested in a model lift fan installed in a wing pod. The three stages had essentially the same aerodynamic performance along the operating line. However, differences in stage thrust characteristics were obtained when a variation in back pressure was imposed on the stages by cross-flow effects and thrust-vectoring louvers.

Stockman, N. O.↗
NASA NTRS1973

A piloted simulation study of the effects of controller force gradient in VTOL hovering flight

A study of the effect of control force gradient on the VTOL visual hovering task was conducted on the NASA-Ames Research Center Six-Degree-of-Freedom Motion Simulator. Lateral control force-gradient characteristics were evaluated in combination with three different types of stabilization systems: An unstabilized (acceleration) system, a rate-stabilized system, and two attitude-stabilized systems. The effects of gust disturbances were included in the control force evaluation for the attitude systems. A force gradient of 1.0 lb/in was within the optimum range for all control systems and conditions evaluated in this study.

Fry, E. B.↗
NASA NTRS1973

Preliminary study of an integral fan lift/cruise engine for a 100 passenger VTOL transport

A simplified mission analysis was performed to determine an optimum engine cycle for a 100-passenger VTOL transport with a range of 500 statute miles. The aircraft had a total of eight integral fan lift engines, three of which serve as cruise engines. Fan pressure ratio was varied from 1.2 to 1.3, overall pressure ratio from 7 to 13, and turbine inlet temperature from 2460 to 2860 R. Bypass ratio was selected to meet a 500-foot altitude flyover noise goal of 95 PNdB. Airplane gross weight and direct operating cost (DOC) were calculated. The lowest DOC of 1.82 cents per seat-mile was achieved with a fan pressure ratio of 1.3, overall pressure ratio of 12, and turbine inlet temperature of 2860 R.

Civinskas, K. C.↗
NASA NTRS1973

Studies in tilt-rotor VTOL aircraft aeroelasticity, volume 1

Aeroelastic and dynamic studies which complement and extend various aspects of technology applicable to tilt-rotor VTOL aircraft are discussed. Particular attention is given to proprotor/pylon whirl instability, a precession-type instability akin to propeller/nacelle whirl flutter. The blade flapping and pitch-change freedoms of a proprotor are shown to lead to a fundamentally different situation as regards the manner in which the precession-generated aerodynamic forces and moments act on the pylon and induce whirl flutter relative to that of a propeller. The implication of these forces and moments with regard to their capacity for instigating a whirl instability is examined, demonstrating why a proprotor can exhibit whirl flutter in either the backward or forward directions in contrast to a propeller which is found to always whirl in the backward direction. Analytical trend studies delineating the effect of several system design parameters on proprotor/pylon stability and response are shown.

Kvaternik, R. G.↗
NASA NTRS1973

Evaluation of glide paths for landing a VTOL airplane using linear regulator theory.

A method of evaluating certain characteristics of approach paths for VTOL airplanes is presented which is based on the solution of the matrix Riccati equation to obtain an optimal state variable feedback controller. The longitudinal equations of motion of the airplane are linearized about a preselected path and the resulting system of equations is treated as a linear, time-varying regulator. The controller which minimizes a quadratic cost function is applied to the linearized system to determine the airplane's ability to return to the prescribed path given a specified initial error in altitude. The procedure is applied to the XC-142A, tilt-wing, V/STOL airplane, under decelerating approach conditions with a glide path consisting of two segments, the first having a smaller angle of descent than the second.

Reid, G. F.↗
NASA NTRS1973

A manual-control approach to development of VTOL automatic landing technology.

The operation of VTOL aircraft in the city-center environment will require complex landing-approach trajectories that insure adequate clearance from other traffic and obstructions and provide the most direct routing for efficient operations. As part of a larger program to develop the necessary technology base, a flight investigation was undertaken to study the problems associated with manual and automatic control of steep, decelerating instrument approaches and landings. The study employed a three-cue flight director driven by control laws developed and refined during manual-control studies and subsequently applied to the automatic approach problem. The validity of this approach was demonstrated by performing the first automatic approach and landings to a predetermined spot ever accomplished with a helicopter. The manual-control studies resulted in the development of a constant-attitude deceleration profile and a low-noise navigation system.

Kelly, J. R.↗
NASA NTRS1974

The effect of wind tunnel wall interference on the performance of a fan-in-wing VTOL model

A fan-in-wing model with a 1.07-meter span was tested in seven different test sections with cross-sectional areas ranging from 2.2 sq meters to 265 sq meters. The data from the different test sections are compared both with and without correction for wall interference. The results demonstrate that extreme care must be used in interpreting uncorrected VTOL data since the wall interference may be so large as to invalidate even trends in the data. The wall interference is particularly large at the tail, a result which is in agreement with recently published comparisons of flight and large scale wind tunnel data for a propeller-driven deflected-slipstream configuration. The data verify the wall-interference theory even under conditions of extreme interference. A method yields reasonable estimates for the onset of Rae's minimum-speed limit. The rules for choosing model sizes to produce negligible wall effects are considerably in error and permit the use of excessively large models.

Heyson, H. H.↗
NASA NTRS1974

The use of an aircraft test stand for VTOL handling qualities studies

The VTOL flight tests stand for testing control concepts on the X-14B VSS aircraft in hover, is described. This stand permits realistic and safe piloted evaluation and checkout of various control systems and of parameter variations within each system to determine acceptability to the pilot. Pilots can use it as a practical training tool to practice procedures and flying techniques and become familiar with the aircraft characteristics. Some examples of test experience are given. The test stand allows the X14B to maneuver in hover from centered position + or - 9.7 deg in roll and + or - 9.3 deg in pitch, about + or - 6 deg in yaw, and + or - 15 cm in vertical translation. The unique vertical free flight freedom enables study of liftoffs and landings with power conditions duplicated. The response on the stand agrees well with that measured in free hovering flight, and pilot comments confirm this.

Pauli, F. A.↗
NASA NTRS1975

Potential and viscous flow in VTOL, STOL or CTOL propulsion system inlets

A method was developed for analyzing the flow in subsonic axisymmetric inlets at arbitrary conditions of freestream velocity, incidence angle, and inlet mass flow. An improved version of the method is discussed and comparisons of results obtained with the original and improved methods are given. Comparisons with experiments are also presented for several inlet configurations and for various conditions of the boundary layer from insignificant to separated. Applications of the method are discussed, with several examples given for specific cases involving inlets for VTOL lift fans and for STOL engine nacelles.

Stockman, N. O.↗
NASA NTRS1975

Simulator evaluation of a perspective clipped-pole display and a thrust-vector controller for VTOL zero-zero landings

Five pilots participated in a simulator study to evaluate design features of a perspective clipped pole display and a side arm thrust vector controller for potential applications to VTOL zero visibility landings. Analyses of objective measures by a t test for related means showed significant learning effects, but did not show significant performance differences among display conditions. A mean longitudinal touchdown velocity of less than 4 knots, a mean vertical touchdown velocity of less than 1.22m/sec, and a mean longitudinal position error of approximately 15.24 m were attained during the final 10 trials of the experiment. The conclusion that adequate airspeed and altitude cues could be obtained from the glideslope and runway poles is supported by the absence of significant performance differences among display conditions.

Murphy, M. R.↗