Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS, COMPLETE - SWEEP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1934

Wing-Nacelle-Propeller Tests - Comparative Tests of Liquid-Cooled and Air-Cooled Engine Nacelles

This report gives the results of measurements of the lift, drag, and propeller characteristics of several wing and nacelle combinations with a tractor propeller. The nacelles were so located that the propeller was about 31% of the wing chord directly ahead of the leading edge of the wing, a position which earlier tests (NASA Report No. 415) had shown to be efficient. The nacelles were scale models of an NACA cowled nacelle for a radial air-cooled engine, a circular nacelle with the V-type engine located inside and the radiator for the cooling liquid located inside and the radiator for the type, and a nacelle shape simulating the housing which would be used for an extension shaft if the engine were located entirely within the wing. The propeller used in all cases was a 4-foot model of Navy No. 4412 adjustable metal propeller. The results of the tests indicate that, at the angles of attack corresponding to high speeds of flight, there is no marked advantage of one type of nacelle over the others as far as low drag is concerned, since the drag added by any of the nacelles in the particular location ahead of the wing is very small. The completely cowled nacelle for a radial air-cooled engine appears to have the highest drag, the liquid-cooled engine appears to have the highest drag, the liquid-cooled engine nacelle with external radiator slightly less drag. The liquid-cooled engine nacelle with radiator in the cowling hood has about half the drag of the cowled radial air-cooled engine nacelle. The extension-shaft housing shows practically no increase in drag over that of the wing alone. A large part of the drag of the liquid-cooled engine nacelle appears to be due to the external radiator. The maximum propulsive efficiency for a given propeller pitch setting is about 2% higher for the liquid-cooled engine nacelle with the radiator in the cowling hood than that for the other cowling arrangements.

Wood, Donald H.↗
NASA NTRS1939

The Effects of Some Surface Irregularities on Wing Drag

The N.A.C.A. has conducted tests to provide more complete data than were previously available for estimating the effects of common surface irregularities on wing drag. The irregularities investigated included: brazier-head and countersunk rivets, spot welds, several types of sheet-metal joints, and surface roughness. Tests were also conducted to determine the over-all effect of manufacturing irregularities incidental to riveted aluminum alloy and to spot-welded stainless-steel construction. The tests were made in the 8-foot high speed wind tunnel at Reynolds Numbers up to 18,000,000. The results show that any of the surface irregularities investigated may increase wing drag enough to have important adverse effects on high-speed performance and economy. A method of estimating increases in wing drag caused by brazier-head rivets and lapped joints under conditions outside the range of the tests is suggested. Estimated drag increases due to rivets and lapped joints under conditions outside the range of the tests is suggested. Estimated drag increases due to rivets and lapped joints on a wing of 20-foot chord flying at 250 miles per hour are shown.

Drag, Manley↗
NASA NTRS1984

Application of a full potential method for computation of three-dimensional supersonic flows

A nonlinear aerodynamic analysis technique based on the full potential equation in conservative form has been modified to permit treatment of supersonic flows with embedded subsonic regions (typically near the fuselage-canopy juncture and the wing leading edge). Solution procedures for the equations do not require any specific form of geometry or physical grid system. This results in the capability to analyze easily very complex geometries provided the posed problem lies within the isentropic restrictions of the full potential theory. Characteristic signal propagation theory is used to monitor the type dependent flow and a conservative switching scheme is employed to transition from the supersonic marching algorithm to a subsonic relaxation procedure and vice versa. An implicit approximate factorization scheme is used to solve the finite-difference equations. These modifications now permit analysis of fully three-dimensional flowfields including the interference effects due to lifting surface wakes. Improved grid generation capability allows analysis of complete complex aircraft geometries (fuselage, wing, tail, wing wake, and tail wake). Results are presented showing very good correlations with experimental surface pressure data and aerodynamic force data at both design and off-design operating points. Configurations examined include several waverider concepts, an arrow wing-body with wake, an advanced tactical fighter concept, and a fighter forebody-canard configuration.

Jones, K. M.↗
NASA NTRS1972

Space shuttle: Longitudinal aerodynamic characteristics of low aspect ratio wing configurations in ground effect for a moving and stationary ground surface

A 0.05-scale model of the NASA-MSC Orbiter 040A Configuration was tested. Test duration was approximately 80 hours during which the model was tested in and out of ground effect with a stationary and moving ground belt. Model height from ground plane surface was varied from one and one-half wing span to landing touchdown while angle of attack varied from -4 to 20 degrees. Eleven effectiveness and alternate configuration geometries were tested to insure complete analysis of low aspect ratio wing aircraft in the presence of ground effect. Test Mach number was approximately 0.067 with a corresponding dynamic pressure value of 6.5 psf.

Romere, P. O.↗
NASA NTRS1960

Experimental Determination of the Effects of Frequency and Amplitude of Oscillation on the Roll-Stability Derivatives for a 60 Degree Delta-Wing Airplane Model

A 60' delta-wing airplane model was oscillated in roll for several frequencies and amplitudes of oscillation to determine the effects of the oscillatory motion on the roll-stability derivatives for the model. The derivatives were measured at a Reynolds number of 1,600,000 for the wing alone, the wing-fuselage combination, and the complete model which included a triangular-plan-form vertical tail. Both rolling and yawing moments due to rolling velocity exhibited large frequency effects for angles of attack higher than 16 degrees. Variations in these derivatives were measured for the lowest frequencies of oscillation; as the frequency increased, the derivatives because more nearly linear with angle of attack. Both velocity derivatives were considerably different at high angles of attack from the corresponding derivatives measured by the steady-state rolling-flow technique. Rolling and yawing moments due to rolling acceleration were measured and similarly found to be highly dependent on frequency at high angles of attack. Some period and time-to-damp computations, which were made to reveal the significance of the acceleration derivatives, indicated that inclusion of the measured derivatives in the equations of motion lengthened the period of the lateral oscillation by 10 percent for a typical delta-wing airplane and increased the time to damp to one-half amplitude by 50 percent.

Fisher, Lewis R.↗
NASA NTRS1975

Stellar model chromospheres. III - Arcturus /K2 III/

Models are constructed for the upper photosphere and chromosphere of Arcturus based on the H, K, and IR triplet lines of Ca II and the h and k lines of Mg II. The chromosphere model is derived from complete redistribution solutions for a five-level Ca II ion and a two-level Mg II ion. A photospheric model is derived from the Ca II wings using first the 'traditional' complete-redistribution limit and then the more realistic partial-redistribution approximation. The temperature and mass column densities for the temperature-minimum region and the chromosphere-transition region boundary are computed, and the pressure in the transition region and corona are estimated. It is found that the ratio of minimum temperature to effective temperature is approximately 0.77 for Arcturus, Procyon, and the sun, and that mass tends to increase at the temperature minimum with decreasing gravity. The pressure is found to be about 1 percent of the solar value, and the surface brightness of the Arcturus transition region and coronal spectrum is estimated to be much less than for the sun. The partial-redistribution calculation for the Ca II K line indicates that the emission width is at least partially determined by damping rather than Doppler broadening, suggesting a reexamination of previous explanations for the Wilson-Bappu effect.

Ayres, T. R.↗
NASA NTRS1989

The oblique-wing research aircraft: A test bed for unsteady aerodynamic and aeroelastic research

The advantages of oblique wings have been the subject of numerous theoretical studies, wind tunnel tests, low speed flight models, and finally a low speed manned demonstrator, the AD-1. The specific objectives of the OWRA program are: (1) to establish the necessary technology base required to translate theoretical and experimental results into practical mission oriented designs; (2) to design, fabricate and flight test an oblique wing aircraft throughout a realistic flight envelope, and (3) to develop and validate design and analysis tools for asymmetric aircraft configurations. The preliminary design phase of the project is complete and has resulted in a wing configuration for which construction is ready to be initiated.

Gilyard, Glenn B.↗
NASA NTRS1978

Experimental Results of Winglets on First, Second, and Third Generation Jet Transports

Results of wind tunnel investigations of four jet transport configurations representing both narrow and wide-body configurations and also a future advanced aerodynamic configuration are presented including performance and wing root bending moment data. The effects of winglets on the aerodynamic characteristics throughout the flight envelope were studied. The results indicate that winglets improved the cruise lift to drag ratio between 4 and 8 percent, depending on the transport configuration. The data also indicate that ratios of relative aerodynamic gain to relative structural weight penalty for winglets are 1.5 to 2.5 times those for wing-tip extensions. Over the complete range of flight conditions, winglets produce no adverse effects on buffet onset, lateral-directional stability, and aileron control effectiveness.

Flechner, S. G.↗
NASA NTRS1980

Attaching of strain gages to substrates

A method and apparatus for attaching strain gages to substrates is described. A strain gage having a backing plate is attached to a substrate by using a foil of brazing material between the backing plate and substrate. A pair of electrodes that are connected to a current source, are applied to opposite sides of the backing plate, so that heating of the structure occurs primarily along the relatively highly conductive foil of brazing material. Field installations are facilitated by utilizing a backing plate with wings extending at an upward incline from either side of the backing plate, by attaching the electrodes to the wings to perform the brazing operation, and by breaking off the wings after the brazing is completed.

Lemcoe, M. M.↗
NASA NTRS1980

Rolling flow wind tunnel tests of F-18 aircraft

The lateral directional characteristics of an F-18 aircraft was investigated. Aerodynamic derivatives associated with pure roll rate, or the 'p' derivatives were obtained. The model is described and the procedures used to obtain and correct the data, and a graphical presentation of the results are presented. These results include graphs of the lateral directional static stability derivatives versus angle of attack, and the lateral directional force and moment coefficients versus nondimensional roll rate. Results are presented for several configurations including complete, complete without vertical tails, complete without horizontal tails, fuselage wing and fuselage alone. Each of these configuations was tested with and without wing leading edge extensions. The basic control surfaces were deflected and the results were investigated.

Lutze, F. H.↗
NASA NTRS1980

Curved flow wind tunnnel test of F-18 aircraft

The curved flow capability of a stability wind tunnel was used to investigate the lateral directional characteristics of an F-18 aircraft. The model is described and the procedures used to obtain and correct the data and a graphical presentation of the results are presented. The results include graphs of lateral directional derivatives versus sideslip or static plots, the lateral directional static stability derivatives versus angle of attack, and finally the lateral directional derivatives versus nondimensional yaw rate for different angles of attack and sideslip. Results are presented for several configurations including complete, complete without vertical tails, complete without horizontal tails, fuselage wing and fuselage alone. Each of these were tested with and without wing leading edge extensions.

Lutze, F. H.↗
NASA NTRS1986

Paneling methods with vorticity effects and corrections for nonlinear compressibility

The prediction of missile aerodynamic characteristics is presently undertaken through the application of supersonic paneling methods and nonlinear corrections to the prediction of missile aerodynamic characteristics. Attention is given to supersonic panel methods and line-singularity methods for the modeling of axisymmetric bodies, in combination with corrections for nonlinear flow phenomena, which are applied to complete missile, inlets, and wing-body combinations. The LRCDM2 computer program is used as an example of the methods presented.

Dillenius, Marnix F. E.↗
NASA NTRS1987

Advanced planar array development for space station

The results of the Advanced Planar Array Development for the Space Station contract are presented. The original objectives of the contract were: (1) to develop a process for manufacturing superstrate assemblies, (2) to demonstrate superstrate technology through fabrication and test, (3) to develop and analyze a preliminary solar array wing design, and (4) to fabricate a wing segment based on wing design. The primary tasks completed were designing test modules, fabricating, and testing them. LMSC performed three tasks which included thermal cycle testing for 2000 thermal cycles, thermal balance testing at the Boeing Environmental Test Lab in Kent, Washington, and acceptance testing a 15 ft x 50 in panel segment for 100 thermal cycles. The surperstrate modules performed well during both thermal cycle testing and thermal balance testing. The successful completion of these tests demonstrate the technical feasibility of a solar array power system utilizing superstrate technology. This final report describes the major elements of this contract including the manufacturing process used to fabricate modules, the tests performed, and the results and conclusions of the tests.

Source record↗
NASA NTRS1989

Transonic CFD applications at Boeing

The use of computational methods for three dimensional transonic flow design and analysis at the Boeing Company is presented. A range of computational tools consisting of production tools for every day use by project engineers, expert user tools for special applications by computational researchers, and an emerging tool which may see considerable use in the near future are described. These methods include full potential and Euler solvers, some coupled to three dimensional boundary layer analysis methods, for transonic flow analysis about nacelle, wing-body, wing-body-strut-nacelle, and complete aircraft configurations. As the examples presented show, such a toolbox of codes is necessary for the variety of applications typical of an industrial environment. Such a toolbox of codes makes possible aerodynamic advances not previously achievable in a timely manner, if at all.

Tinoco, E. N.↗
NASA NTRS1989

Test techniques for cryogenic wind tunnels

Some of the testing techniques developed for transonic cryogenic tunnels are presented. Techniques are emphasized which required special development or were unique because of the opportunities offered by cryogenic operation. Measuring the static aerodynamic coefficients normally used to determine component efficiency is discussed. The first topic is testing of two dimensional airfoils at transonic Mach numbers and flight values of Reynolds number. Three dimensional tests of complete configurations and sidewall mounted wings are also described. Since flight Reynolds numbers are of interest, free transition must be allowed. A discussion is given of wind tunnel and model construction effects on transition location. Time dependent phenomena, fluid mechanics, and measurement techniques are examined. The time dependent, or unsteady, aerodynamic test techniques described include testing for flutter, buffet, and oscillating airfoil characteristics. In describing non-intrusive laser techniques, discussions are given regarding optical access, seeding, forward scatter lasers, two-spot lasers, and laser holography. Methods of detecting transition and separation are reported and a new type of skin friction balance is described.

Lawing, Pierce L.↗
NASA NTRS1989

Aerodynamic testing in cryogenic nitrogen gas - A precursor to testing in superfluid helium

Testing techniques for transonic cryogenic tunnels using nitrogen as the test fluid are presented. The measurement of static aerodynamic coefficients used to determine component efficiency is discussed, focusing on tests of two-dimensional airfoils at transonic Mach numbers. Also, three-dimensional tests of complete configurations and sidewall mounted wings are examined. Consideration is given to time-dependent phenomena, fluid mechanics, nonintrusive laser techniques, the detection of transition and separation, and testing for flutter, buffet, and oscillating airfoil characteristics.

Lawing, Pierce L.↗
NASA NTRS1991

Recent manufacturing advances for spiral bevel gears

The U.S. Army Aviation Systems Command (AVSCOM), through the Propulsion Directorate at NASA LRC, has recently sponsored projects to advance the manufacturing process for spiral bevel gears. This type of gear is a critical component in rotary-wing propulsion systems. Two successfully completed contracted projects are described. The first project addresses the automated inspection of spiral bevel gears through the use of coordinate measuring machines. The second project entails the computer-numerical-control (CNC) conversion of a spiral bevel gear grinding machine that is used for all aerospace spiral bevel gears. The results of these projects are described with regard to the savings effected in manufacturing time.

Handschuh, Robert F.↗
NASA NTRS1991

Recent manufacturing advances for spiral bevel gears

The U.S. Army Aviation Systems Command (AVSCOM), through the Propulsion Directorate at NASA Lewis Research Center, has recently sponsored projects to advance the manufacturing process for spiral bevel gears. This type of gear is a critical component in rotary-wing propulsion systems. Two successfully completed contracted projects are described. The first project addresses the automated inspection of spiral bevel gears through the use of coordinate measuring machines. The second project entails the computer-numerical-control (CNC) conversion of a spiral bevel gear grinding machine that is used for all aerospace spiral bevel gears. The results of these projects are described with regard to the savings effected in manufacturing time.

Handschuh, Robert F.↗