Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - DESIGN WING, TAPERED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1939

The effects of partial-span slotted flaps on the aerodynamic characteristics of a rectangular and a tapered N.A.C.A. 23012 wing

An investigation was made in the N.A.C.A. 7- by 10-foot wind tunnel to determine the aerodynamic characteristics of tapered and rectangular wings with partial-span slotted flaps. Two N.A.C.A. 23012 airfoils equipped with center-section and tip-section flaps were tested. The results showed that the changes in lift and drag due to changes in flap span for both rectangular and tapered wings having partial-span slotted flaps were similar to those for corresponding wings having partial-span split or plain flaps. For the two wings tested, higher values of maximum lift were obtained with center-section slotted flaps than with tip-section slotted flaps of the same size. The highest values of lift-drag ratio at maximum lift for the rectangular wing were obtained with center-section flaps and, for the tapered wing, with tip-section flaps. Center-section flaps on the tapered wing gave higher values of drag at maximum lift than tip-section flaps; no great difference in drag at maximum lift was apparent for either center-section or tip-section slotted flaps on the rectangular wing.

House, Rufus O↗
NASA NTRS1938

The effects of partial-span plain flaps on the aerodynamic characteristics of a rectangular and a tapered Clark Y wing

An investigation was made to determine the aerodynamic characteristics of tapered and rectangular wings with partial-span plain flaps. Two Clark Y airfoils equipped with center section and with tip-section flaps were tested. The results showed that the aerodynamic characteristics of partial-span plain flaps were, in general, similar to those of split flaps of the same span, but that the lift and the drag were less for the wing with plain flaps than for the wing with split flaps of comparable size. For the rectangular wing with center-section plain flaps, the maximum lift and the lift-drag ratio at maximum lift were greater and the drag at maximum lift was less than for the wing with tip-section plain flaps of the same size. The maximum lift of the tapered wing varied in the same manner as that of the rectangular wing but the drag and the lift-drag-ratio relationship were opposite.

House, R O↗
NASA NTRS1973

Wind-tunnel roll-damping measurements of a winged space shuttle configuration in launch attitude

Ground-wind load studies were conducted on three model configurations to assess the importance of aeroelastic instabilities of erected space shuttle vehicles. Roll damping was measured on a fuselage-alone model, which had a D cross section, and a fuselage and tail surfaces in combination with either a clipped-delta wing or a low-sweep tapered wing as the primary lifting surface. The largest negative roll-damping coefficients were measured with the fuselage-alone configuration and were a function of wind azimuth. At the wind azimuths at which the wing-fuselage configuration was unstable, the negative roll-damping coefficients were a function of reduced frequency.

Hess, R. W.↗
NASA NTRS1941

Observations of the Effect of Wing Appendages and Flaps on the Spread of Separation of Flow over the Wing

The spread of the separation of flow on three tapered wings insymmetrical and unsymmetrical flow was observed with silk tufts. By equal thickness and chord distribution the wings manifested a different form of lifting line. The principal result of the study was that the wings alone first disclosed complete breakdown of the flow at the tips, even the one with twist, but that after adding fuselage and engine nacelles, the twisted wing broke down completely first in the wing center. The observed boundary layer motions transverse to the main flow direction were briefly explored as to their possible influence on the spread of the separation. On top of that certain disclosures were afforded in which the transverse motions observed in the boundary layer became perceptible even above the boundary layer.

Hartwig, G↗
NASA NTRS1976

Sample wings for study

Two simple wings were selected for study using the various implementations (old and new) of the vortex lattice method. These are: (1) a rectangular wing with an aspect ratio of 2, and (2) a tapered wing with an aspect ratio of 5, a taper ratio of 0.5, a leading sweep of 3.317 deg., and a trailing edge sweep of 1-11.308 deg. This was done in order to gain an appreciation for the accuracy of the various implementations. References were given where force, moment, and pressure data could be found for these wings.

Lamar, J. E.↗
NASA NTRS1924

The Effect of Airfoil Thickness and Plan Form on Lateral Control

This investigation was carried out for the purpose of determining the effectiveness of ailerons and tests were made on six model airfoils in the no. 1 wind tunnel of the National Advisory Committee for Aeronautics. The method consisted in measuring the rolling moments and aileron moments in the ordinary way. In addition to this the wing was allowed to spin freely about an axis in the direction of the air flow and the angular velocity measured. The results show that the thickness of the airfoil has very little effect on either the rolling moment or the hinge moment, although the resulting efficiency is somewhat higher for the tapered wings. The airfoil tapered in plan form, however, shows practically no falling off in the rolling moment at the critical angle of attack, whereas the wings of rectangular plan form show a marked dropping off in the rolling moment at this point. This indicates that it is possible to obtain good lateral control with small ailerons at low speed if the plan form is tapered. The rotational speed of the different airfoils is practically the same for all of the sections tested.

Hoot, H I↗
NASA NTRS1939

Wind-tunnel Investigation of Ground Effect on Wings with Flaps

An investigation was conducted in the N.A.C.A. 7- by 10-foot wind tunnel to determine the effect of ground proximity on the aerodynamic characteristics of wings equipped with high-lift devices. A rectangular and a tapered wing were tested without flaps, with a split flap, and with a slotted flap. The ground was represented by a flat plate, completely spanning the tunnel and extending a considerable distance ahead and back of the model. The position of the plate was varied from one-half to three chord lengths below the wing. The results are presented in the form of curves of absolute coefficients, showing the effect of the ground on each wing arrangement. The effect of the ground on lift, drag, and pitching moment is discussed. An appendix gives equations for calculating tunnel-wall corrections to be applied to ground-effect tests conducted in rectangular tunnels when a plate is used to represent the ground. The tests indicated that the ground effect on wings with flaps is a marked decrease in drag, a decrease in diving moment, and a substantial reduction in maximum lift.

Recant, Isidore G↗
NASA NTRS1951

Theoretical antisymmetric span loading for wings of arbitrary plan form at subsonic speeds

A simplified lifting-surface theory that includes effects of compressibility and spanwise variation of section lift-curve slope is used to provide charts with which antisymmetric loading due to arbitrary antisymmetric angle of attack can be found for wings having symmetric plan forms with a constant spanwise sweep angle of the quarter-chord line. Consideration is given to the flexible wing in roll. Aerodynamic characteristics due to rolling, deflected ailerons, and sideslip of wings with dihedral are considered. Solutions are presented for straight-tapered wings for a range of swept plan forms.

Deyoung, John↗
NASA NTRS1974

An analytical study of the effects of jets located more than one jet diameter above a wing at subsonic speeds

A procedure has been developed to calculate the effects of blowing two jets over a swept tapered wing at low subsonic speeds. The algorithm used is based on a vortex lattice representation of the wing lifting surface and a line sink-source distribution to simulate the effects of the jet exhaust on the wing lift and drag. The method is limited to those cases where the jet exhaust does not intersect or wash the wing. The predictions of this relatively simple procedure are in remarkably good agreement with experimentally measured interference lift and interference induced drag.

Putnam, L. E.↗
NASA NTRS1974

An analytical study of the effects of jets located more than one jet diameter above a wing at subsonic speeds

A procedure has been developed for calculating the effects of blowing two jets over a swept tapered wing at low subsonic speeds. The algorithm used is based on a vortex-lattice representation of the wing lifting surface and a line sink-source distribution to simulate the effects of the jet exhaust on the wing lift and drag. The method is limited to those cases in which the jet exhaust does not intersect or wash the wing. The predictions of this relatively simple procedure are in remarkably good agreement with experimentally measured interference lift and interference induced drag.

Putnam, L. E.↗
NASA NTRS1997

Steady-State Solution of a Flexible Wing

A fluid-structure interaction code, ENSAERO, has been used to compute the aerodynamic loads on a swept-tapered wing. The code has the capability of using Euler or Navier-Stokes equations. Both options have been used and compared in the present paper. In the calculation of the steady-state solution, we are interested in knowing how the flexibility of the wing influences the lift coefficients. If the results of a flexible wing are not affected by the flexibility of the wing significantly, one could consider the wing to be rigid and reduce the problem from fluid-structure interaction to a fluid problem.

Karkehabadi, Reza↗
NASA NTRS2019

Shape Sensing for Wings with Spars and Ribs Using Simulated Strain

Active trim shape control can be used to minimize error between target and actual aircraft trim shape during flight. Trim shape sensing for aircraft during flight is not only important for highly flexible aircraft, such as the National Aeronautics and Space Administration (NASA) Helios Prototype remotely piloted flying wing aircraft, but also for a delta-wing type aircraft, such as a supersonic commercial transport aircraft. A two-step theory utilizing distributed strain for a real-time shape sensing of a full three-dimensional structure has been introduced previously. This study focuses on the application of the two-step theory to finite element models of a wing with spars and ribs such as the X-59 QueSST aircraft (Lockheed Martin Corporation, Bethesda, Maryland), a tapered wing, a dihedral/anhedral wing, and a stiffened dihedral/anhedral wing. A finely meshed finite element structural model is desired to capture accurate curvature distributions along the neutral axes of the wing cross sections during pre-test analysis for shape sensing of a wing with ribs and spars. The two-step theory used in this study gives excellent deformation correlation with the MSC/NASTRAN (MSC Software, Newport Beach, California) results along the neutral axis for all test cases used in this study except the X-59 QueSST aircraft.

strain↗
NASA NTRS1976

The calculation of steady non-linear transonic flow over finite wings with linear theory aerodynamics

The feasibility of calculating steady mean flow solutions for nonlinear transonic flow over finite wings with a linear theory aerodynamic computer program is studied. The methodology is based on independent solutions for upper and lower surface pressures that are coupled through the external flow fields. Two approaches for coupling the solutions are investigated which include the diaphragm and the edge singularity method. The final method is a combination of both where a line source along the wing leading edge is used to account for blunt nose airfoil effects; and the upper and lower surface flow fields are coupled through a diaphragm in the plane of the wing. An iterative solution is used to arrive at the nonuniform flow solution for both nonlifting and lifting cases. Final results for a swept tapered wing in subcritical flow show that the method converges in three iterations and gives excellent agreement with experiment at alpha = 0 deg and 2 deg. Recommendations are made for development of a procedure for routine application.

Cunningham, A. M., Jr.↗
NASA NTRS1989

Application of the CAP-TSD unsteady transonic small disturbance program to wing flutter

The application and assessment of a computer program called CAP-TSD (Computational Aeroelasticity Program - Transonic Small Disturbance) for flutter predictions are described. Flutter calculations are presented for two thin swept-and-tapered wing planforms with well-defined modal properties. One planform is a series of 45-degree swept wings and the other planform is a clipped delta wing. Comparisons are made between the results of CAP-TSD using the linear equation and no airfoil thickness and the results obtained from a subsonic kernel function analysis. The calculations cover a Mach number range from low subsonic to low supersonic values, including the transonic range, and are compared with subsonic linear theory and experimental data. It is noted that since both wings have very thin airfoil sections, the effects of thickness are minimal.

Bennett, Robert M.↗
NASA NTRS1958

Experimental Wind-Tunnel Investigation of the Transonic Damping-in-Pitch Characteristics of Two Wing-Body Combinations

The results of an experimental wind-tunnel investigation of the damping in pitch of two wing-body combinations are presented. The tests were conducted in the Ames 14-foot transonic wind tunnel over a Mach number range from 0.60 to 1.18. Reynolds numbers varied from 2.3 million to 5.5 million. One model with a triangular wing of aspect ratio 2 having NACA 0003-63 sections was oscillated at an amplitude of 1.5 and a frequency of 17 cycles per second. The second model with a straight, tapered wing of aspect ratio 3 having 3-percent biconvex circular-arc sections was oscillated at an amplitude of 1.0 deg and a frequency of 21 cycles per second. The tests were made with the models at a mean angle of attack of 0 deg. The models were oscillated with a dynamic balance that was actuated by an electrohydraulic servo valve. The results of this investigation indicate the usefulness of this new apparatus. The experimental results of a previous damping-in-pitch investigation conducted in the Ames 6- by 6-foot supersonic wind tunnel at Mach numbers from 1.2 to 1.7 are included along with the theoretical results for this Mach number range. In the region of Mach numbers available for comparison, good agreement is shown to exist between the data obtained in the two facilities, except for some inconsistency in the slopes of the curves at M = 1.2 for the triangular wing. The results of this investigation clearly show that for the models tested the maximum values of the damping in pitch occur at Mach numbers very close to 1.0, and that abrupt changes in the pitch damping are encountered near sonic velocity.

Emerson, Horace F.↗