Search NASA⌕ Search

SEARCH · Search NASA

Results for “XPS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Thermal stability of oxidized ultrathin Li films on TZM for plasma facing components

For improved understanding of the behavior of Li plasma facing components (PFCs) in the presence of oxygen impurities, we report on the thermal stability of ultrathin (up to 1.0 nm) LiO x films on a titanium-zirconium-molybdenum (TZM) alloy substrate over the temperature range of 310–1400 K. LiO x films were prepared by either post-oxidation of Li films or Li films deposited on an oxygen-precovered TZM surface. Thermal stability of these films was studied using a combination of temperature programmed desorption (TPD), X-ray photoelectron spectroscopy (XPS), and low-energy ion scattering (LEIS). For post-oxidized Li films, TPD showed that no Li desorption occurred until temperatures above 620 K, and then Li desorbed from the surface via at least three desorption peaks. The O 1s XPS spectra on the post-oxidized films at 310 K indicate the formation of lithium oxide (Li2O) and peroxide/hydroxide (Li 2 O 2 /LiOH). The peroxide/hydroxide converts to oxide after heating to 680 K with no desorption of Li or O 2 , and then this film decomposes to liberate Li into the gas phase while leaving oxygen at the TZM surface. Heating the LiO x films to 1070 K led to a solid-state reaction with surface Mo atoms of the substrate to form a condensed binary lithium molybdenum oxide (LixMoOy) phase, which upon further heating decomposed to liberate gas phase binary lithium molybdenum oxide species. Li deposition on an oxygen-precovered TZM surface formed a complex, highly stable, oxygen rich, Li-O-Mo interfacial oxide. Li desorption from multilayer Li films on oxygen-precovered TZM surfaces occurred in a metallic Li multilayer peak and three other oxide-derived peaks. These results support the improved thermal stability of oxidized lithium as compared to metallic Li and have implications for Mo impurity transport into the plasma at high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Multi-technique characterization of spray coated and roll-to-roll coated gas diffusion fuel cell electrodes

Here this work reports the characterization of catalyst layer (CL) structure and composition for a set of gas-diffusion electrodes (GDEs) fabricated by different coating methods with the goal of developing a better understanding of CL processing-structure-property-performance relationships. The CL coating techniques used in this study were ultrasonic spray coating, and two roll-to-roll (R2R) methods - gravure and slot die. Scanning transmission electron microscopy (STEM) coupled with X-ray energy dispersive spectroscopy (EDS) analysis of GDE cross-sections provided bulk information, while scanning electron microscopy (SEM) with EDS and X-ray photoelectron spectroscopy (XPS) were used to investigate the near surface and surface composition of the CLs that will be in direct contact with the membrane once the membrane electrode assembly (MEA) is constructed. This study demonstrates that common quantification parameters, namely the F:Pt ratio extracted from cross-sectional STEM-EDS maps and top-down CL measurements with SEM and XPS, along with roughness parameters quantified from SEM micrographs are useful parameters in explaining and potentially predicting performance trends. Additionally, it highlights the importance of understanding key CL surface properties for advancing the manufacturability of high-performance components for polymer electrolyte membrane (PEM) technologies.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Microscopic analysis of copper current collectors and mechanisms of fragmentation under compressive forces

Extensive fragmentation of copper current collectors was observed after spherical indentation on prismatic and large-format pouch Li-ion cells by 3D X-ray computed tomography (XCT). Microscopic analysis including scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM) and x-ray photoelectron microscopy (XPS) was carried out on copper current collectors from used commercial cells and pristine anodes. The copper-graphite cross-section images showed rough interface areas affected by reactions and diffusion in the used cell. Electron probe micro-analyzer (EPMA) element mapping showed the interface area was rich in oxygen and phosphorus. A detectable amount of phosphorus was also uniformly distributed inside the current collector. The same oxygen and phosphorus distributions were confirmed by STEM/EDS analysis. XPS depth profiles on multiple elements revealed the interface area of the aged anode was rich in Li, F, P, O and C and diffused at least 50 nm into the copper. In comparison, the pristine anode showed a very smooth C/Cu interface. No other elements were detected. For commercial cells, the reactions in the interface area and diffusion of multiple elements into the lattice and grain boundaries were responsible for the embrittlement of the copper current collectors. Finally, permanent cell capacity loss was observed in electrochemical performance of the indented cells.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Pool boiling critical heat flux studies of accident tolerant fuel cladding materials

Pool boiling experiments have been performed at atmospheric pressure on potential accident tolerant fuel (ATF) cladding materials (Zirlo®, Cr coated Zirlo®, FeCrAl coated Zirlo®, and monolithic SiC) to evaluate the Critical Heat Flux (CHF) points. Corrosion resistant coatings of Cr and FeCrAl alloy were deposited on flat Zirlo® samples using cold spray technology. The as-prepared samples after uniform surface polishing were subjected to autoclave tests at 360 °C water and 18.6 MPa for 360 h to simulate prototypic corrosion of the ATF cladding materials in LWR normal operation. Surface characteristics potentially influencing CHF such as surface morphology, roughness, static contact angle, and surface chemistry were characterized using a suite of characterization methods including scanning electron microscopy, 3D optical profilometry, optical contact angle measurements, and x-ray photoelectron spectroscopy (XPS). Thermo-physical properties of the samples such as density, thermal conductivity, and heat capacity were measured by differential scanning calorimetry and laser flash thermal diffusivity measurement. FeCrAl coatings showed CHF values comparable to bare Zirlo® samples, while slightly lower CHF values were observed for Cr coated samples and bulk SiC flats (produced by chemical vapor deposition, CVD). As-deposited Cr coatings showed 67% higher CHF than the as-polished Cr coatings due to its higher surface roughness level. The autoclave testing for the prepared samples generally increased the CHF except for the surface polished Cr coatings. Similar CHF values of bare Zirlo®, FeCrAl coating, and CVD SiC samples were observed after autoclave test but there were negligible change CHF of Cr coatings. XPS studies indicated that the formation or deposition of a few monolayers of hydrophobic carbonaceous species on surface can affect CHF values. The trends in CHF data are discussed in terms of evolution of the surface characteristics of the ATF materials.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Laser-interference pulse number dependence of surface chemistry and sub-surface microstructure of AA2024-T3 alloy

The laser-based treatment of a metal surface is an intrinsically non-chemical technique that can alter both the topology and chemistry of surfaces. A laser-based treatment for coating and joining applications can offer alternative surface preparations to the chemically-based surface preparation techniques, which are subject to severe environmental protection and hazardous-waste management considerations. In this study, the surface chemistry and sub-surface microstructural changes are investigated for a novel surface processing method using laser interferometry produced by two beams of a pulsed Nd:YAG laser. The two-beam laser-interference allowed the structuring of the surface at length scales much less than that of the laser beam spot. Surface chemistry changes in the oxide layer of AA 2024-T3 aluminum alloy rolled sheet due to laser processing were investigated using x-ray photoelectron spectroscopy (XPS). Near surface microstructural changes have been investigated with scanning electron microscopy and energy dispersive x-ray spectroscopy (SEM/EDS), and scanning transmission electron microscopy (STEM) as a function of number of interfering laser shots. SEM microstructure pictures of the top surface shows the minimization of surface defects, as all of the sharp features from a rolled sheet surface were smoothed by laser-structuring. STEM images indicate that the laser-interference processing reduced the formation of CuMn-rich precipitates over a 500–800 nm depth from the top surface. XPS data indicated that the Al oxide layer is modified compared to that of the baseline specimen and that the oxide thickness increases with the number of shots per spot. Finally, the additional thicker oxide on Al alloys is expected to increase the corrosion resistance of the coated Al 2024.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Innovative recycling of high purity silver from silicon solar cells by acid leaching and ultrasonication

Precious and scarce silver (Ag) is used as a front electrical contact in silicon solar panels. With massive amounts of solar panel waste coming to end-of-life, it is imperative to recover all the Ag from these modules. In this paper, we propose a novel method to easily reclaim Ag from end-of-life silicon solar cells using low concentration sulfuric acid (H 2 SO 4 ) leaching followed by ultrasonication. Our process simplifies the Ag recycling procedure by directly recovering the Ag contacts from solar cells, eliminating the need for secondary precipitation/electrodeposition. First, scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDX) and X-ray photoelectron spectroscopy (XPS) was used to study the leaching and ultrasonication process on rejected solar wafers. Next, a solar panel from landfill was heated in a furnace to burn off the polymer encapsulant. The silicon wafers were then collected from the burning process and leached in 2 M H 2 SO 4 at two different shaking speeds for 48 hours at room temperature. Finally, the end-of-life silicon wafer pieces were collected, sonicated in water, and then the sonication water was centrifuged to show a proof-of-concept to recover the Ag contacts. Inductively coupled plasma optical emission spectroscopy (ICPOES) is used to monitor dissolved elements in the leachate as a function of time and shaking speed. XPS is used to evaluate the composition of the silicon cell wafer surface before and after H 2 SO 4 leaching. SEM is used to image the recovered Ag contacts morphology and EDX confirms the recovered particles contain high amounts of Ag. Furthermore, a proposed schematic illustrates the authors’ hypothesis for the peeling mechanism.

14 SOLAR ENERGY↗
DOE OSTI2021

Synthesis of a planar, multicomponent catalytic surface of Na 2 CO 3 /MnO

Here, O 2 adsorption on MnO(100) precovered with sodium (Na) multilayers was investigated by X-ray photoelectron spectroscopy (XPS) and temperature programmed desorption (TPD). Deposition of Na multilayers leads to a first monolayer of oxidic Na followed by metallic Na island growth. XPS results for the oxidation of the metallic Na islands indicate an incomplete oxidation of Na at 125 K. Oxidation at 350 K completely oxidizes the metallic islands producing a mixture of Na 2 O and Na 2 O 2 . Thermal evolution of the oxidation products was examined. After oxidation at 350 K and flashing to 750 K, Na 2 O and Na 2 O 2 are the primary oxides on MnO(100). After flashing to 850 K, a solid state reaction of Na 2 O 2 /Na 2 O and the MnO(100) substrate forms a NaMnO 2 -like surface compound which decomposes above 850 K. Oxygen exchange between CO 2 and Na oxides is observed. The strong interaction between CO 2 and Na oxide islands forms Na 2 CO 3 on MnO(100). Heating the Na 2 CO 3 covered MnO(100) surface to 600 K for 10 min drives oxidic Na in the first monolayer into the MnO subsurface, and produces a surface exposing islands of Na 2 CO 3 on MnO(100).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Understanding the morphology and chemical activity of model ZrO x /Au (111) catalysts for CO 2 hydrogenation

In this study, the growth of ZrO x on Au (111) was investigated using scanning tunneling microscopy (STM) and synchrotron-based ambient pressure X-ray photoelectron spectroscopy (AP-XPS). Nanostructures of ZrO x (x= 1,2) at the sub-monolayer (≤ 0.3 ML) level were prepared by vapor depositing Zr metal onto Au (111) followed by oxidation with O 2 or CO 2 . At low coverages of the admetal (< 0.05 ML), the formed ZrO x nanostructures were dispersed randomly on the terraces and steps of the Au(111) substrate. Strong oxide-metal interactions prevented the formation of islands of zirconia. The ZrO x nanostructures displayed a reactivity towards CO 2 and H 2 not seen for bulk zirconia. C 1 s AP-XPS results indicated that CO 2 molecules adsorbed on Zr/ZrO x /Au(111) surfaces could undergo partial decomposition on Zr (CO 2 , gas → CO gas + O ads ), or react with oxygen sites from ZrO x to yield carbonates (Zr-CO 3, ads ). Further, after exposing ZrO 2 /Au (111) surfaces to 1:3 mixtures of CO 2 :H 2 , the formation of HCOO, CO 3 , and CH 3 O was detected in AP-XP spectra. These chemical species decomposed at temperatures in the range of 400-600 K, making them possible reaction intermediates for methanol synthesis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Surface structure of Sn doped β-Ga 2 O 3 (010) p(1×1) studied by quantitative low energy electron diffraction

Here, we have studied the surface structure of a single crystal β-Ga 2 O 3 (010) using quantitative Low Energy Electron Diffraction (LEED) and X-ray photoelectron spectroscopy (XPS). The XPS measurements show spectra typical of stoichiometric Ga 2 O 3 with a clean surface. LEED consistently shows a p(1x1) pattern, free of surface reconstruction. Quantitative LEED I(V) curves are acquired for 41 distinct diffraction spots. The experimental I(V) curves are compared to simulations over the first five layers. The best fits to the experimental LEED I(V) curves acquired at all diffraction spots are then used to calculate the interplanar relaxation and atomic rumpling. Significant atomic rumpling and interplanar relaxation are found over the first 5 atomic layers. As a result of rumpling a polarization of ~ 2 μC/cm 2 develops in the topmost surface layer. The structural results are in good agreement with previous density functional theory calculations and experimental X-ray photoelectron diffraction.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electrochemical-driven green recovery of lithium, graphite and cathode from lithium-ion batteries using water

The expected exponential increase in consumption of lithium-ion batteries (LIBs) would pose a unique challenge to the availability of near-critical resources like lithium and graphite in the upcoming decade. In this work, we present a lithium recovery process that utilizes a degradation mechanism, i.e., lithium plating, as a tool to concentrate metallic lithium at the anode/separator interface for convenient extraction at room temperature – using only water. Electrochemical characterization of fast charged (1–6 C) LIBs yielded a maximum capacity fade of 50% over ten cycles. The lithium plating was confirmed via voltage plateau analysis, coulombic efficiency, and DC resistance measurements. A maximum lithium plating condition was observed to exist between 4C and 5C, thereby limiting the energy consumption in the extraction process. Post-mortem film thickness measurement showed an incrementing film deposition with a maximum of 35 µm thickness. SEM and XPS analysis confirmed increasing concentration of a dense dendritic metallic lithium deposition on the anode/separator interface with C-rate. A green recovery process was adopted to extract the concentrated metallic lithium using distilled water. The lithium from the plated film, solid/electrolyte interface (SEI), electrolyte, anode, and cathode, was extracted as salts. A 37% improvement in lithium recoverability was achieved with fast charging under ambient conditions. XPS analysis showed ~92% of lithium yield with no residual lithium in the graphite. In addition, the battery-grade graphite was recovered with 97% purity after heat treatment of the washed anode film, and concentrated transition metals oxides in the cathode to 93% purity for convenient extraction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Functionalized Polymer Thin Films for Plutonium Capture and Isotopic Screening from Aqueous Sources

The rapid screening of plutonium from aqueous sources remains a critical challenge for nuclear nonproliferation efforts. The determination of trace-level Pu isotopes in water requires offsite sample preparation and analysis; therefore, new methods that combine plutonium purification, concentration, and isotopic screening in a fieldable detection system will provide an invaluable tool for nuclear safeguards. This contribution describes the development and characterization of thin polymer-ligand films for the isolation and concentration of waterborne Pu for direct spectroscopic analyses. Submicron thin films were prepared through spin coating onto Si wafers and consisted of combinations of polystyrene (PS) with dibenzoylmethane, thenoyltrifluoroacetone, and di(2-ethylhexyl)phosphoric acid (HDEHP). Pu uptake studies from solutions at pH from 2.3 to 6.3 indicated that only films containing HDEHP exhibited significant recovery of Pu. High alpha spectroscopy peak energy resolutions were achieved for PS-HDEHP films over a range of film thicknesses from 30 to 250 nm. Furthermore, a separate study was performed to evaluate uptake from a primarily Pu(V) solution where it was observed that doubling the HDEHP loading in the film increased uptake of Pu by an order of magnitude. X-ray photoelectron spectroscopy (XPS) analysis revealed that HDEHP was highly concentrated within the first few nanometers of the film at the higher loading. XPS analysis also revealed that, in the presence of water, HDEHP was stripped from the surface layer of the film at circumneutral pH. While significant losses of ligand were seen in all samples, higher loadings of HDEHP resulted in measurable amounts of ligand retained after a 12-h soak in water. Findings of this study are being used to guide the development of thin-film composite membrane-based detection methods for the rapid, fieldable analysis of Pu in water.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Synthesis and Electrical Properties of a New Compound (BiSe) 0.97 (Bi 2 Se 3 ) 1.26 (BiSe) 0.97 (MoSe 2 ) Containing Metallic 1T-MoSe 2

The synthesis and electrical properties of a new misfit compound containing BiSe, Bi 2 Se 3 , and MoSe 2 constituent layers are reported. The reaction pathway involves competition between the formation of (BiSe) 1+x (Bi 2 Se 3 ) 1+y (BiSe) 1+x (MoSe 2 ) and [(Bi 2 Se 3 ) 1+y ] 2 (MoSe 2 ). Excess Bi and Se are required in the precursor to synthesize (BiSe) 1+x (Bi 2 Se 3 ) 1+y (BiSe) 1+x (MoSe 2 ). High-angle annular dark field-scanning transmission electron microscopy (HAADF-STEM) confirm the stacking sequence of the heterostructure. Small grains of both 2H- and 1T-MoSe 2 are observed in the MoSe 2 layers. X-ray photoelectron spectroscopy (XPS) indicates that there is a significantly higher percentage of 1T-MoSe 2 in (BiSe) 1+x (Bi 2 Se 3 ) 1+y (BiSe) 1+x (MoSe 2 ) than in (BiSe) 0.97 (MoSe 2 ), suggesting that more charge transfer to MoSe 2 occurs due to the additional BiSe layer. The additional charge transfer results in (BiSe) 1+x (Bi 2 Se 3 ) 1+y (BiSe) 1+x (MoSe 2 ) having a low resistivity (14–19 μΩ m) with metallic temperature dependence. Furthermore, the heterogeneous mix of MoSe 2 polytypes observed in the XPS complicates the interpretation of the Hall data as two bands contribute to the electrical continuity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Elucidating the Redox Behavior during Atomic Layer Deposition on Lithium-Ion Battery Cathode Materials

Atomic layer deposition (ALD) has emerged as a promising technology for applying ultrathin protective coatings on lithium-ion battery (LIB) cathode surfaces to improve their cycling stability. While there have been numerous reports evaluating the electrochemical performance of these surface-modified cathode materials, the chemical changes induced on the surface of the cathode materials upon ALD coating are not fully studied. This paper describes a systematic investigation to understand the interfacial changes of 12 different cathode materials upon coating with aluminum oxide (Al 2 O 3 ) using trimethyl aluminum (TMA) and H 2 O, and aluminum fluoride (AlF 3 ) using TMA and hydrogen fluoride pyridine (HFPy). Here, the surface composition of these cathode materials, which range from simple transition metal oxides (e.g. NiO and MnO) to complex multi-element cathode materials (e.g. LiNi x Mn 1-x-y Co y O 2 , NMC), was studied via X-ray photoelectron spectroscopy (XPS). The XPS measurements reveal that the transition metals in the cathode materials undergo selective oxidation/reduction depending upon the nature of the precursor, the coating, and the cathode material. The ability to chemically modify the surface of cathode materials via vapor-phase precursor adsorption will open new avenues to systematically control the interface of the cathode materials in LIBs that are not possible by conventional coating methods.

25 ENERGY STORAGE↗
DOE OSTI2023

Adapting an Electron Microscopy Microheater for Correlated and Time-Resolved Ambient Pressure X-ray Photoelectron Spectroscopy

Environmental transmission electron microscopy (ETEM) can follow structural and chemical changes in nanomaterials under reaction conditions, including at temperatures up to 1300 °C and pressures up to ~20 mbar. However, ETEM studies are limited to localized areas of a sample and can benefit from correlative studies of a similar sample on larger length scales. Here, in this work, we describe the customization of a commercial microheater holder used in ETEM to anode-based ambient pressure X-ray photoelectron spectroscopy (APXPS), where chemical and electronic structure information is averaged over several hundred square micrometers. To benchmark heating capabilities in the APXPS instrument, core level binding energies were followed during surface chemical reactions of a Pd film, including CO adsorption–desorption, Pd oxidation, and PdO reduction. The fast heating feature of the microheaters advanced XPS experimental capabilities, including the collection of subsecond time-resolved spectra of the Pd 3d 5/2 peak during the reduction of an oxidized Pd film. The potential to use these heaters in a closed gas cell was also demonstrated by oxidizing Pd in a partial pressure of air locally dosed to the sample surface. General tips and considerations for the application of commercial ETEM heaters to any XPS system with a focused X-ray beam are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Descriptor-Based Analysis of Atomic Layer Deposition Mechanisms on Spinel LiMn 2 O 4 Lithium-Ion Battery Cathodes

Protective coatings have been shown to effectively suppress Mn ion dissolution from the spinel LiMn 2 O 4 lithium-ion battery cathode by stabilizing the surface against undesired side reactions with the electrolyte. In spite of extensive study, however, there remains a lack of atomic-scale understanding of how such coatings are deposited, and no molecular-level descriptor to predict trends in deposition mechanisms has been identified. We have recently shown that Al 2 O 3 coatings grown by atomic layer deposition (ALD) with alternating trimethylaluminum (TMA) and water exposures exhibit submonolayer growth because of precursor decomposition on the lithium manganate spinel (LMO) surface during early ALD pulses. In the present work, we elucidate the underlying mechanisms of this Al 2 O 3 ALD process using density functional theory (DFT) calculations and X-ray photoelectron spectroscopy (XPS) experiments, and we introduce a generalized descriptor-based framework to understand the resulting trends across a spectrum of surface structures and functionalities. We demonstrate that all decomposition products, including CH 3 -aluminum adducts and dissociated CH 3 groups, are Lewis bases and are coordinated to oxygen atoms on the LMO surface, leading to charge transfer to Lewis acidic Mn 3d states. Inert-transfer XPS supports these theoretical predictions, showing an increase in near-surface Mn 3+ content following TMA exposure and shifts in C is spectra consistent with C-O bond formation. We extend the DFT studies to various low- and high-index LMO surface facets, as a proxy for tuning the Lewis acid-base interactions between surface-bound CH 3 * and near-surface Mn ions. The thermochemistry for TMA reactions on these chemically distinct LMO surfaces demonstrates that ALD is structure-sensitive and that there is higher reactivity for TMA decomposition and Al 2 O 3 nucleation near LMO steps and defects. Motivated by the Lewis basic character of the decomposition products, we introduce the oxygen vacancy formation energy as a descriptor for decomposition energetics, and we demonstrate that all energetics are correlated to this quantity through the number of electrons that are transferred along the reaction coordinate. Finally, based on these findings, we hypothesize that improved electrochemical cycling with only 1-2 ALD cycles may be due to selective passivation of defect sites on the LMO surface that are more susceptible to Mn dissolution, and we suggest that similar descriptor-based analyses could be useful for the study of other ALD coatings on oxide substrates.

25 ENERGY STORAGE↗
DOE OSTI2025

Direct Prelithiation of Silicon-Based Composite Electrodes via Island-like Thermal Evaporation

Irreversible losses of Li during solid electrolyte interface (SEI) conditioning is a key contributor to the lower specific capacities observed in silicon-containing Li-ion batteries. Herein, thermal evaporation of between 1 and 20 µm of Li onto Si-based composite anodes has been investigated as a prelithiation method to account for such losses. To account for mechanical strain caused by Li-Si alloying during the deposition, a stainless-steel mesh is applied to the electrodes before prelithiation to form “island-like” deposition on the electrode surface. The open circuit potential was also found to decrease as a function of increased Li evaporation, consistent with the potentials of electrochemically prepared LixSi alloys. Prelithiating to account for irreversible Li losses to SEI formation resulted in full cells with a 15.8% increase in initial coulombic efficiency and a 47.8% reduction in irreversible capacity loss after SEI formation cycling. Subsequent C/3 cycling showed up to a 62.9% increase in specific capacity in prelithiated cells. X-ray photoelectron spectroscopy (XPS) revealed differences in the SEI composition that was formed by electrochemical cycling and reactively formed in prelithiated cells upon exposure to Gen2 + 3% FEC electrolyte. The reactively formed SEI from the spontaneous reaction with lithiated silicon was carbonate-rich while the electrochemical SEI formation showed significantly more LiPFx species, which could play a role in overall cycling performance.

Musgrove, Amanda↗
DOE OSTI2025

Deactivation of Mo/H-ZSM-5 in Microwave-Assisted and Thermal-Driven Methane Dehydroaromatization

A better understanding of catalyst deactivation is needed to improve catalyst design and performance in microwave-enhanced methane dehydroaromatization (MDA). Here, this study investigates the deactivation of a molybdenum supported H-ZSM-5 zeolite (Mo/H-ZSM-5) catalyst in MDA under microwave-heated conditions, comparing its performance to that of the same catalyst under conventional heating. While the microwave-assisted (MW) process achieved higher benzene yields, the catalyst experienced faster deactivation due to the selective and rapid deposition of coke within the pores of the zeolite, as confirmed through Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD), ammonia-temperature programmed desorption (NH 3 -TPD), thermal gravimetric analysis (TGA), temperature programmed oxidation (TPO), and X-ray photoelectron spectroscopy (XPS) analyses. The quantification of total coke content via TGA/TPO and surface carbon (XPS) revealed that nearly twice as much coke was deposited on the catalyst under MW conditions compared to that on the conventionally heated material, and the coke exhibited a more conductive and graphitic nature. The accelerated deactivation rates were attributed to the formation of hot spots in the MW system, leading to enhanced coupling with coke formed in situ during the reaction and resulting in increased Mo reduction. Observations indicated that the CO activation used to carburize the catalyst prior to the reaction is not advantageous in the MW heating environment. The presence of large amounts of Mo oxides at elevated temperatures (through hot spots) exposed to methane leads to instability under the reaction conditions. Optimizing the activation environment and improvement of the Mo dispersion within the pores are potential strategies to improve catalyst stability.

Mo/H-ZSM-5 zeolite↗
DOE OSTI2025

Facile Solvent-Free Synthesis of Manganese Nickel-Layered Double Hydroxide for Sustainable Water-Splitting Applications

The quest for efficient and sustainable water-splitting electrocatalysts has led to the development of a novel bifunctional material, manganese nickel-layered double hydroxide (MnNi-LDH), which demonstrates promising performance for both the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER). Although manganese-based materials are less explored than other transition metals, they offer significant potential owing to their widespread availability, affordability, and customizable electronic characteristics. MnNi-LDH exhibits a nanosheet morphology and a layered structure, which collectively provide numerous accessible active sites and facilitate efficient charge transfer and mass transport. Characterization using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy, and transmission electron microscopy reveals the structural and compositional properties of MnNi-LDH. The oxidation states of Mn and Ni, as determined by XPS, play a crucial role in improving the catalytic activity. Notably, MnNi-LDH demonstrates low overpotentials of 187 mV for OER and 225 mV for HER at 10 mA/cm 2 current density comparable to conventional catalysts. Long-term stability tests show minimal degradation in cell performance over 50 h, with a current density drop of only 0.6153% per hour for the OER and 0.37% per hour for the HER. Further, these findings highlight the potential of MnNi-LDH as a promising and environmentally friendly bifunctional electrocatalyst for water splitting, contributing to the advancement of renewable energy sources.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗