SEARCH · Search NASA

Results for “advanced accelerator test facilities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS2004

High-Temperature Hybrid Rotor Support System Developed

The Army Research Laboratory Vehicle Technology Directorate and the NASA Glenn Research Center demonstrated a unique high-speed, high-temperature rotor support system in September 2003. Advanced turbomachinery is on its way to surpassing the capabilities of rolling-element bearings and conventional dampers. To meet these demands, gas turbine engines of the future will demand increased efficiency and thrust-to-weight ratio, and reduced specific fuel consumption and noise. The more-electric engine replaces oil-lubricated bearings, dampers, gears, and seals with electrical devices. One such device is the magnetic bearing. The Vehicle Technology Directorate and Glenn have demonstrated the operation of a radial magnetic bearing in combination with a hydrostatic bearing at 1000 F at 31,000 rpm (2.3 MDN1). This unique combination takes advantage of a high-temperature rub surface in the event of electrical power loss or sudden overloads. The hydrostatic bearings allow load sharing with the magnetic bearing. The magnetic-hydrostatic bearing combination eliminates wear and high contact stress from sudden acceleration of the rolling-element bearings and overheating. The magnetic bearing enables high damping, adaptive vibration control, and precise rotor positioning, diagnostics, and health monitoring. A model of the test facility used at Glenn for this technology demonstration is shown. A high-temperature heteropolar radial magnetic bearing is located at the center of gravity of the test rotor. There is a 0.022-in. radial air gap between the rotor and stator. Two rub surface hydrostatic bearings were placed on either side of the magnetic bearing. The rotor is supported by a 0.002-in. hydrostatic air film and the magnetic field. The prototype active magnetic bearing cost $24,000 to design and fabricate and a set of four high temperature, rub-surface, hydrostatic bearings cost $28,000. This work was funded by the Turbine-Based Combined Cycle program.

Montague, Gerald T.↗

DOE OSTI2023

νBDX: a Coherent Elastic Neutrino Nucleus Scattering (CEνNS) experiment at Jefferson Lab

Particle physics is an ever-changing field seeking to explain phenomena that lie at the limits of our current knowledge. Among discovered and hypothesized interactions, Coherent Elastic Neutrino-Nucleus Scattering (CE?NS) stands out as a fascinating and elusive phenomenon, offering a unique window into the nature of neutrinos and their interactions with matter. CE?NS, a process predicted by the Standard Model, represents one of the subtle ways in which neutrinos can interact with atomic nuclei. Unlike other neutrinonucleus interactions, CE?NS occurs coherently, meaning that the entire nucleus collectively responds to the neutrino-mediated weak force, resulting in small energy transfers to the nucleus as a whole. The extremely rare nature of CE?NS events presents a formidable challenge to experimenters seeking to detect and study these interactions. Recent advances in detector technologies and the implementation of large-scale experiments, such as coherent neutrino scattering experiments at research facilities around the world, have opened up new avenues for exploring this elusive phenomenon. These experiments aim not only to observe CE?NS directly but also to extract valuable information on neutrino properties, nuclear structure, and potential deviations from the Standard Model. This thesis aims to study the feasibility of an experiment to study CE?NS at The Thomas Jefferson National Accelerator Facility, Newport News, VA, USA. This would be an experiment that exploits the production of neutrinos by an electron beam dumped on a thick target (the beam dump). The large quantity of neutrinos produced and their energy profile are well suited to the purpose of studying the CE?NS. In my thesis, I will start from previous studies on CE?NS and from theoretical considerations regarding the process, then quantify the expected events for a hypothetical experiment and possible backgrounds through simulations aimed at optimizing the geometry of the future detector. I will also show some tests on selected detector components that will be part of a first prototype.

Grazzi, Stefano↗

DOE OSTI2023

MRT 7365: Power flow physics and key physics phenomena

The Z accelerator at Sandia National Laboratories conducts z-pinch experiments at 26 MA in support of DOE missions in stockpile stewardship, dynamic materials, fusion, and other basic sciences. Increasing the current delivered to the z-pinch would extend our reach in each of these disciplines. To achieve increases in current and accelerator efficiency, a fraction of Z’s shots are set aside for research into transmission-line power flow. These shots, with supporting simulations and theory, are incorporated into this Advanced Diagnostics milestone report. The efficiency of Z is reduced as some portion of the total current is shunted across the transmission-line gaps prior to the load. This is referred to as “current loss”. Electrode plasmas have long been implicated in this process, so the bulk of dedicated power-flow experiments are designed to measure the plasma environment. The experimental analyses are enhanced by simulations conducted using realistic hardware and Z voltage pulses. In the same way that diagnostics are continually being improved for sensitivity and resolution, the modeling capability is continually being improved to provide faster and more realistic simulations. The specifics of the experimental hardware, diagnostics, simulations, and algorithm developments are provided in this report. The combined analysis of simulation and data confirms that electrode plasmas have the most detrimental impact on current delivery. Experiments over the last three years have tested the theoretical current-loss mechanisms of enhanced ion current, plasma gap closure, and Hall-related current. These mechanisms are not mutually exclusive and may be coincident in the final feed as well as in upstream transmission lines. The final-feed geometries tested here, however, observe lower-density plasmas without dominant ion currents which is consistent with a Hall-related current. The picture of plasma formation and transport formed from experiment and simulation is informing hardware designs being fielded on Z now and being proposed for the Next-Generation Pulsed Power (NGPP) facility. In this picture, the strong magnetic fields that heat the electrodes above particle emission thresholds also confine the charged particles near the surface. Some portion of the plasmas thus formed is transported into the transmission-line gap under the force of the electric field, with aid from plasma instabilities. The gap plasmas are then transported towards the load by a cross-field drift, where they accumulate and contribute to a likely Hall-related cross-gap current. The achievements in experimental execution, model validation, and physical analysis presented in this report set the stage for continued progress in power flow and load diagnostics on Z. The planned shot schedule for Z and Mykonos will provide data for extrapolation to higher current to ensure the predicted performance and efficiency of a NGPP facility.

43 PARTICLE ACCELERATORS↗

DOE OSTI2023

Determining the Effects of Neutron Irradiation on the Structural Integrity of Additively Manufactured Heat Exchangers for Very Small Modular Reactor Applications, DOE Final Report (Project # 19-16980)

Auburn University (AU) teamed with the University of Missouri Research Reactor (MURR) and Kansas State University (KSU) to determine how to best use laser-powder bed fusion (L-PBF) additive manufacturing (AM) methods for generating radiation resistant nickel-based superalloys, Inconel alloy 625 and 718, for special purpose reactor (SPR) or very small modular reactor (vSMR) heat-exchangers (HeXs). Compact, conformal, and durable HeXs that are tolerant of extreme environments are needed for supporting the technical maturity of next-generation, portable compact reactors. AM is an enabler for realizing this new wave of HeXs – providing a means to make customizable hot and cold stream architectures with novel flow path geometries (e.g., tortuous channels with non-uniform, asymmetric cross-sections) and reduced layer-to-layer contact resistance (i.e., no separate bonding procedure required). AM further enables a more time/cost efficient means for fabricating SPRs by reducing the number of suppliers required for HeX assembly and allowing for on-site HeX fabrication. The project aim has been to better understand how neutron irradiation affects the microstructure and properties of additively manufactured nickel-based superalloys, to accelerate their safe, reliable use in the modular reactor industry. The major objective was to qualify/quantify the microstructure and microhardness of nickel-based superalloys (including Inconel 718 and 625) additively manufactured via the L-PBF process in the neutron-dosed (irradiated) and non-irradiated states over a course of 3 years. Effects of build orientation during L-PBF and post-AM heat treatments on neutron resistance, microstructure and mechanical properties were also investigated. Neutron damage mechanisms via hardening were characterized. This project combined subject-matter experts in AM, mechanical/microstructure metallic part characterization, and neutron irradiation, as well as unique assets and capabilities at AU and MURR at MU, to ensure project results translated to effectively addressing known gaps in nuclear science and engineering. Parts were fabricated using L-PBF systems readily available at AU. Specimens were then irradiated using MURR facilities; a manipulator equipped hot cell was also used to measure material hardness after dosing. MURR, a 10 MW, light-water nuclear reactor, is the largest, highest powered, highest-flux university owned research reactor in the U.S. The major findings in this project provide evidence that AM can serve as an alternative way to build structural components for future advanced small modular reactors using advanced materials like Inconel 625 (IN625) or Inconel 718 (IN718). After full spectrum neutron irradiation, vertically as-built AM IN625 samples were observed to display better resistance towards radiation-induced-hardening defects relative to traditionally machined metals. A Vickers microhardness tester, using settings of 1 kgf and dwell time of 15 seconds per indentation, was used to measure hardness in this study. The as-built, vertically printed samples experienced 1.2% of radiation hardening vs. 5.25% radiation hardening observed in wrought IN625. Another set of IN625 and IN718 samples were exposed to fast neutron irradiation. It was observed that IN718 showed more resistance towards radiation hardening compared to IN625 samples indicating IN718 had a better performance. Results showed that the IN718 samples experienced less change (-2.5 to 3.24 %) in microhardness. On the other hand, IN625 samples underwent more (0.9 to 7.21%) change in microhardness after fast neutron irradiation. AM IN625 samples were irradiated using an ion (proton) beam in cyclotron. The mechanical properties of AM samples post irradiation were compared with wrought samples. The irradiated region on the samples were tested using nano-hardness indention. It was observed that the beam current and time used in this study generated an annealing effect and thus reduced the hardness of the samples. The sum of the project results provide precious insight into how one may minimize radiation hardening in AM materials while maintaining material property constraints. Results should assist engineers in selecting an appropriate heat treatment for AM nickel-based superalloys for increased radiation resistance. Results should increase confidence levels for adopting AM for building nuclear reactor components which perform the same or better than conventionally manufactured components. Fast neutron irradiation testing provided an accelerated means of obtaining radiation effects without making materials radioactive and difficult to handle.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2026

Development Status of the KIPM Detector Consortium

A kinetic inductance phonon-mediated detector is a calorimeter that uses kinetic inductance detectors (KIDs) to read out phonon signals from the device substrate. We have established a consortium comprising university and national lab groups dedicated to advancing the state of the art in these detectors, with the ultimate goal of designing a detector with sub-eV threshold on energy deposited in the substrate, enabling searches for both light dark matter and low-energy neutrino interactions. This consortium brings together experts in KID design, phonon and quasi-particle dynamics, and noise modeling, along with specialized fabrication facilities, test platforms, and unique calibration capabilities. Recently, our consortium has demonstrated a resolution on energy absorbed by the sensor of 2.1 eV, the current record for phonon-sensitive KIDs. However, due to ∼ 1% phonon collection efficiency, the overall detector resolution was limited to 320 eV. Finally, the current focus of the consortium is modeling and improving the phonon collection efficiency and implementing low-T c superconductors, both of which serve to improve the overall energy resolution and threshold of the detectors.

Temples, Dylan J. [Fermi National Accelerator Labo↗

DOE OSTI2024

Design improvements to the SNS ion source and diagnostics

The U.S. Spallation Neutron Source (SNS) is a state-of-the-art neutron scattering facility delivering the world's most intense pulsed-neutron beams to a wide array of instruments which are used to conduct investigations in many fields of science and engineering. The accelerator system is fed by an RF-driven, multicusp, H - ion source which nominally provides pulsed beam currents of 50-60 mA (1ms, 60Hz). This report provides a discussion of ongoing design improvements to the SNS ion source and Low Energy Beam Transport (LEBT) as well as diagnostic upgrades undertaken since the previous ICIS conference. These improvements include (i) simple mechanical modifications to the source outlet aperture which resulted in dramatically increased extracted beam current and comparable or lower emittance at similar beam currents, (ii) design improvements to the LEBT chopper target which will enable full power beam-dumping during physics studies, (iii) refinement of the SNS Allison emittance scanner that has enabled the first reliable LEBT beam measurements at full beam power (65kV, 50-100mA, 1ms, 60Hz) on the SNS ion source test stand and (iv) the implementation of a thermal imaging camera for the monitoring the LEBT electrode temperatures. (v) The design of an advanced Cs system, capable of more efficient Cs utilization with significantly lower Cs losses from the source is also presented. Mechanical details, computational simulations and experimental results are discussed within the context of these improvements.

47 OTHER INSTRUMENTATION↗

DOE OSTI2023

Advanced Algal Biofoundries for the Production of Polyurethane Precursors

The primary goal of the BEEPs project was to develop a process that could accelerate the development of algae as bioproduction platforms, from initial chemical product concept to an economically viable market supply. Under this program we elected to develop strains of algae that could generate polyurethane precursors, while simultaneously developing basic genetic tools to enable improved algal production systems. This program was specifically designed to incorporate National Laboratories as a means to utilize the expertise and facilities for new bio-production platforms. To that end, we designed a program to collaborate with the Agile BioFoundry at Lawrence Berkeley National Laboratory (LBNL) and computational platforms at Pacific Northwest National Laboratory (PNNL). In addition to these National Laboratory partners, we also had academic partners from UC Davis and Georgia Tech, as well as commercial partners Algenesis Materials and BASF. To achieve these goals, we initially focused on developing the genetic tools and high throughput screening technologies necessary to generate and assess production of polymer precursors (succinic acid) in algae and cyanobacteria, including advanced promoters and biosensors. In parallel, we computationally identified potential production bottlenecks and then used the developed genetic tools to increase production rates and yields. Constant feedback of data was used in conjunction with machine learning, high-throughput cell sorting, and synthetic biology, for additional targeted metabolic engineering. Multiple rounds of tool design, building, testing, and learning were supplied to partners at PNNL and LBNL to develop new models and tools that could expedite bioproduction platform development and increase yield performance. We targeted, and achieved, the FOA requirement yield metric of 20 g/L, as a milestone and deliverable from at least one of our engineered strains for the production of succinic acid.

09 BIOMASS FUELS↗

DOE OSTI2023

Investigation of the Role of the Role of Nuclear Physics in Heavy Element Nucleosynthesis, through the Study of Key Reactions, and the Improvement of Theoretical Reaction Rates (Final Report)

Neutrino-driven winds in core-collapse supernovae have been identified as a possible site for the production of elements heavier than iron. Traditionally, these neutrino-driven winds have been proposed as the site of the main r-process. Recent simulations fail to reproduce the conditions required for the main r-process. while they remain a promising site for producing the lightest elements beyond iron, e.g., Sr, Y, and Zr through the νp process. The efficiency of the νp process depends on the hydrodynamical conditions, the electron fraction (which is related to the neutrino properties), and the nuclear reactions on many short-lived nuclei with limited (if at all) experimental information. The reaction rates on these nuclei are based on theoretical predictions using the Hauser-Feshbach model. Recent sensitivity studies have highlighted the importance of neutron-induced reactions on these nuclei along the νp process path. This work aimed to experimentally constrain reaction rates that are known to play a key role in the neutrino-p process nucleosynthesis. A secondary subsequently-added objective was to start the implementation of techniques that improve the description of nuclear properties in the Hauser-Feshbach model by extending the microscopic nuclear level density description offered via the shell model to high excitation energies without using experiment-based renormalizations. The main objective of this work was the experimental constraint of the 56 Ni(n,p) 56 Co reaction rate via a measurement of the inverse reaction 56 Co(p,n) 56 Ni at the National Superconducting Cyclotron Laboratory (NSCL) and later the Facility for Rare Isotope Beams (FRIB). This reaction is considered the key one for determining the yields possible by the neutrino-p process. A technique for this type of measurement in inverse kinematics at low energies did not exist before this work. The work also had two secondary objectives. First, to contribute to efforts to measure the same reaction in direct kinematics using a radioactive target at Los Alamos National Laboratory (LANL), and second, to advance work to implement shell-model-deduced microscopic level densities in Hauser-Feshbach calculations. The project has resulted in the development of the first technique to perform (p,n) cross-section measurements in relevant-for-astrophysics low energies in inverse kinematics using a magnetic spectrometer or separator, and neutron detectors for neutron tagging. It has also resulted in the precise measurement of the cross-section of the 40 Ar(p,n) 40 K reaction in a proof-of-principle experiment realized by using a beam-line quadrupole of the ReA3 accelerator of NSCL/FRIB. As part of this project the technique was successfully adapted to make use of the superior acceptance of the Separator for Capture Reactions (SECAR) at FRIB. In this project, the required experimental setup simulations and beam optics were developed and tested with the measurement of the 58 Fe(p,n) 58 Cu reaction cross-section. Additionally, this project contributed with simulation work to the development of a technique to measure (n,p) reactions with radioactive targets at LANL, and which resulted in the measurement of the key 56 Ni(n,p) 56 Co reaction cross-section at neutron energies above ≈1 MeV. Last, the project initiated work in the development of shell model based level densities using the moments method.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

NASA NTRS2000

Mechanically Induced g-Jitter from Space Station Rotary Joints

The mission of the International Space Station is to provide a working laboratory in orbit for research in engineering, life sciences, and microgravity. Among the microgravity disciplines that are preparing to utilize this international resource are materials processing, combustion, fluid dynamics, biotechnology, and fundamental physics. The Station promises to enable significant advances in each of these areas by making available a research facility in which gravitational and other accelerations, and their corresponding buoyancy and diffusion effects on various physical processes, are orders of magnitude lower than they are on Earth. In order to fulfill this promise, it is not enough for the Space Station to simply replicate a typical terrestrial scientific laboratory in orbit. Although an orbiting laboratory is free of most of the effects of gravitational acceleration by virtue of its free fall condition, it also produces structural vibration or jitter that can interfere with the processes under study. To ensure the quality of the acceleration environment and enable a successful mission, the Space Station Program has limited potential disturbances in two ways: first, by isolating the most sensitive payloads from the vehicle structure, and second, by quieting major disturbances at their sources. The first area, payload isolation, is implemented inside the pressurized modules at the rack level. Sub-rack level isolators have also been developed. This paper addresses the second area, disturbance source limits, for one of the major sources of mechanical noise on the Space Station: the Solar Alpha Rotary Joints. Due to the potential for large disturbances to the microgravity environment, an initial analytical prediction of rotary joint vibration output was made. Key components were identified and tested to validate the analytical predictions. Based on the component test results, the final vibration output of the joints was verified by a test on each fully assembled flight unit. This paper describes the Space Station microgravity requirements, the rotary joint hardware, and the disturbance producing aspects of joint operation. The test setup, instrumentation, test conditions, and results for the component level and system level measurements are described. An overall forcing function that describes the maximum torque imparted to the Station is created based on the test results, and these disturbances are shown to meet the applicable Space Station microgravity requirements.

Boucher, Robert L.↗

DOE OSTI2025

Closing the Accuracy Gap in Tandem Photovoltaic Testing: An Accessible and Efficient Spectral Tuning Method Using LED-Based Simulators for Research Laboratories and Industry

Accurate performance calibration of multijunction (MJ) solar cells is critical for advancing this technology toward large-scale terrestrial application, yet existing testing methods developed by photovoltaics calibration laboratories remain prohibitively complex and resource intensive for most research laboratories. Current approaches rely on expensive multisource simulators and/or intricate spectral tuning algorithms, limiting accessibility and hindering standardized comparisons of emerging MJ technologies such as perovskite-based tandems. This paper introduces a streamlined spectral irradiance adjustment method for light-emitting diode (LED)-based solar simulators, which are increasingly adopted in the photovoltaics community due to their versatility and cost-effectiveness. The method we present bins LED channels into groups based on the number of junctions of the MJ photovoltaic device under test (DUT) and their corresponding band gaps and incorporates an automated tuning algorithm that eliminates the need to adjust each channel’s irradiance individually. This tuning algorithm requires the relative spectral responsivities of both the DUT and a broadband reference cell, as well as a calibrated spectroradiometer. Measurement validation across various MJ devices, including III-V and perovskite/silicon tandems, demonstrates excellent agreement within 1% with well-established xenon-tungsten multisource simulators and associated tuning algorithms. By enabling precise spectral tuning with readily available equipment and a simple tuning algorithm, our approach bridges the measurement accuracy gap between research laboratories and accredited testing facilities, fostering more reliable device comparisons and accelerating the translation of MJ technologies into real-world energy systems.

14 SOLAR ENERGY↗

DOE OSTI2026

Final Technical Report for U.S.-Japan Hadronic Physics Exchange Program for Studies of Hadron Structure and QCD

Nuclear physics explores the fundamental properties of matter -- how protons and neutrons emerge as quantum systems of elementary particles, how they form the atomic nuclei, and how they give rise to the wide variety of phenomena and applications at biological, technical, and astronomical scales. It is a global scientific effort centered around large-scale experimental user facilities (particle accelerators and detectors), advanced theoretical methods and concepts, and computational techniques and resources. Exchange of knowledge and ideas, scientific collaboration, and workforce development on a global scale are essential for the future of the field. The nuclear physics program envisaged in the 2023 DOE/NSF NSAC Long-Range Plan and pursued at the U.S. National Labs has strong synergies with programs at other facilities worldwide and will realize significant benefits from international collaboration. Nuclear physics is also recognized for promoting international cooperation in the broadest sense through joint construction and operation of experimental equipment, personal contacts between scientists, and education and training. The U.S.-Japan Hadronic Physics Exchange Program (USJPHE) supported collaborative scientific research in hadronic physics and quantum chromodynamics. USJHPE focused on subject areas related to the programs at current and future experimental facilities in the U.S.\ and Japan and supported both experimental and theoretical studies. USJHPE particularly aimed to realize synergies between the hadronic physics programs at Jefferson Lab 12 GeV and J-PARC resulting from the complementarity of electromagnetic and hadronic probes in the multi-GeV energy range. Subject areas of common interest included the quark-gluon structure of hadrons and nuclei, meson and baryon spectroscopy, strangeness and hypernuclear physics, and other related topics. USJHPE also supported research in hadronic physics and nuclear-physics-enabled tests of fundamental symmetries related to the programs at Brookhaven National Lab, Fermilab, KEK, Spring-8, and university-based facilities in the U.S. and Japan. USJHPE especially promoted collaboration between the U.S. and Japanese nuclear physics communities in developing the physics program and instrumentation for the future Electron-Ion Collider. USJHPE was intended to provide travel grants to U.S.-based scientists (primary institutional affiliation with a U.S.\ university, national laboratory, or other research center) to visit Japanese institutions and conduct collaborative research there. The program supported senior researchers, postdoctoral fellows, and students. Continuing the setup of the preceding grant period, J-PARC served as the Japanese “hub” for U.S. physicists for short- and long-term visits, and JLab served as the corresponding U.S. “hub”. The program was officially managed through the U. of Connecticut in Storrs, CT. Support for Japanese physicists visiting the U.S. was provided through funds from Japanese funding agencies. The USJHPE program promoted the scientific exchange and the collaborative spirit in hadronic physics between the two countries.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2025

60 years of science in ICF: from conception to scientific breakeven on the National Ignition Facility

The recent achievements of a burning plasma, fusion ignition, and scientific energy gain with deuterium-tritium (DT) fuel at Lawrence Livermore National Laboratory’s National Ignition Facility (NIF) represents a major milestone in the development of inertial confinement fusion (ICF) and all of fusion research. In these experiments, fuel pressures well in excess of hundreds of GBars were achieved in the compressed fuel, and robust alpha heating of the fuel, far in excess of the energy provided by the implosion, were demonstrated for the first time. These achievements occurred 60 years after the inception of ICF and the first laser demonstration, and were made possible by more than five decades of research at laser facilities around the world. Advances in laser technology both in wavelength and precision, motivated by improved understanding of laser-plasma interaction physics and the demands of targets; improvements in target fabrication inspired by the need to control and minimize hydrodynamic instabilities in the implosion; and multi-dimensional simulations and diagnostics have been critical to this achievement. This paper will summarize the scientific and technical advances, the surprises, and the challenges that had to be overcome to achieve these goals.

fusion↗

DOE OSTI2024

Integration of a new Cryogenic Liquefier into the IB-1 Cryogenic Test Facility

The increase over the last years of the testing activities related to quantum systems, SRF cavities for the PIP-II and the LCLS-II projects, as well as superconducting magnets for the HL-LHC project and Fusion research activities, has required the addition of a new Helium cryogenic plant into the existing IB-1 Industrial Cryogenic Test Facility. The new cryogenic plant is composed of a cryogenic liquefier (Cold Box) able to provide up to 340 L/h, a 4 kL Dewar and two Mycom ® compressors providing up to 120 g/s. AL-AT (Air Liquide Advanced Technologies) has taken part of this project by designing and manufacturing the cryogenic liquefier. This new cryogenic plant is connected through a cryogenic distribution system to a 10 kL Dewar, which is part of the existing cryogenic test facility, itself composed of another Cold Box and a Sullair ® compressor. The new cryogenic plant has two main operating modes: one allows to transfer liquid helium at 1.7 bar between the two Dewars, the other allows to transfer supercritical Helium at 2 bar or more between the new Cold Box and the 10 kL Dewar. The entire industrial cryogenic facility is handled by a common Inventory Control System, composed of three control valves, and 9 tanks giving a total buffer volume of more than 1000 m3. This paper presents the technical features of the new Helium cryogenic plant, as well as the main results of the liquefier commissioning phase and details of the helium transfer between the two Dewars, making the connection between the cryogenic plants at the IB-1 Industrial Cryogenic Test Facility.

43 PARTICLE ACCELERATORS↗

NASA NTRS2020

Apollo Next Generation Sample Analysis (ANGSA): A Segue to the Next Era of Lunar Exploration and Sample Return Activities

In the fifty years since the first lunar samples were collected on Apollo 11, significant advancements have taken place in laboratory analysis, planetary science, and astromaterials curation. These advances are now being leveraged for the Apollo Next Generation Sample Analysis (ANGSA) Program, which aims to study specially curated Apollo samples that have never been studied before. Since Apollo 17 in 1972, a great deal has been learned about the Moon, including the unique environments of the poles. Building upon Apollo and remote sensing studies since then, the Artemis Program aims to explore the cold environments near the lunar south pole while achieving the concurrent goals of landing the first woman and the next man on the Moon by 2024. Recent developments for ANGSA have significantly accelerated our readiness for Artemis sample return, particularly in the area of cold sample studies. Four science teams were selected to study cold and/or volatile-bearing samples collected during the Apollo program. These samples have special storage and handling requirements that necessitate their processing in a -20°C environment that meets the Apollo materials and cleanliness requirements. NASA has recently undertaken the development and implementation of a cold sample processing facility to support ANGSA. A similar facility will be needed to process the cold, volatile-bearing samples planned to be returned by Artemis missions; therefore, ANGSA provides excellent preparation for Artemis’ future cold sample processing efforts. We will outline the goals of the ANGSA and Artemis programs, illustrating the complementary nature of the work for both. We will describe the efforts to date in designing, testing, and implementing a cold curation facility that meets the requirements of ANGSA and Apollo curation. We will then outline future work for that facility to reach operational readiness. Finally, we will present the sample collection and curation strategies for Artemis, showing how they overlap and build on ANGSA efforts. The development of cold curation at NASA represents a significant leap in the knowledge, experience, and technologies used in astromaterials curation, opening the door for new investigations of lunar volatiles, impacts, formation processes, prebiotic chemistry, and resource utilization, among many others.

Julie Mitchell↗

DOE OSTI2025

Heat load measurements for the PIP-II pHB650 cryomodule

This study presents a brief overview of the 1st and 2nd phases and an in-depth analysis of the 3rd phase heat load testing performed on the pHB650 (prototype High Beta 650 MHz) cryomodule at PIP2IT (PIP-II Injector Test Facility), with a focus on both the results and the methodological advancements that have improved testing efficiency and accuracy. A key challenge identified in the testing campaign is the higher-than-expected heat loads observed in the first PIP-II (Proton Improvement Plan II) prototype cryomodules (pSSR1 and pHB650) tested at PIP2IT. Elevated heat loads are concerning given the fixed capacity of the PIP-II cryoplant that is currently being installed at Fermilab. However, understanding the sources of these elevated heat loads offers a critical opportunity to implement effective heat load mitigations on upcoming PIP-II cryomodules to stay within the available capacity of the PIP-II cryoplant. The study includes a summary of test results, descriptions of measurement procedures, and key observations on parameters directly and indirectly related to heat load measurements. Direct observations include measured heat loads and the effectiveness of JT heat exchanger under varying conditions, while indirect observation analyze factors such as the temperature distribution on the two-phase pipe and relief piping under varying conditions. Thermal acoustic oscillations (TAO) were identified during testing, which was mitigated by replacing the original G10 stem with a stainless steel stem equipped with wipers for the cryomodule cooldown valve. A major innovation during pHB650 Phase 3 testing was the development of an automated Python script to streamline data acquisition, analysis, and reporting of heat load results. This script automatically retrieved data from ACNET (Accelerator Control Network), performed heat load calculations, and generated detailed reports featuring plots and tables. This advancement significantly reduced manual labor and enhanced the thoroughness of data analysis compared to earlier campaigns. The heat load test reports were promptly uploaded to the electronic logbook shortly after each test, enabling rapid feedback and collaboration between the SRF and cryogenic teams. The heat load measurements included various components: HTTS (high-temperature thermal shield), LTTS (low-temperature thermal shield), 2K isothermal and non-isothermal heat loads. Results were recorded both within the cryomodule and between the bayonet can supply and return. Measurements were conducted under different operating conditions such as "standard", "linac", and "simulated dynamic". Additionally, HTTS and LTTS heat loads were calculated in real time, allowing for the tracking of thermal stability and identification of changes during testing, both in steady-state and transient conditions. The results of this testing campaign not only provide valuable insights into the performance of the pHB650 cryomodule but also highlight best practices and lessons learned that will inform future cryomodule testing at PIP2IT. These include adopting automated tools for data analysis, refining real-time measurement capabilities, and emphasizing detailed pre-test planning. The framework established in this campaign aims to set an improved standard for cryomodule testing and heat load reporting in future cryomodule test campaigns.

Porwisiak, D. [Fermilab; Wroclaw Tech. U.]↗

DOE OSTI2023

NETL Direct Air Capture Center

In 2022 Congress authorized the $25M National Energy Technology Laboratory Direct Air Capture Center. The facility will be specifically targeted at accelerating the commercialization of technologies beyond the conceptual stage which have not yet reached full pilot-scale (TRL 3 to 6). The ability to operate over a wide range of conditions will help the developers to understand how their technologies respond in different climates, from summer to winter and arid to tropical. NETL recognizes that DAC technology is still early in its evolution, and a wide variety of highly varied technologies are being explored. The Center will be designed with substantial flexibility to accommodate the rapidly evolving technological landscape. Testing systems at three scales will be included: lab-scale systems designed to examine the long-term stability of DAC materials, bench-scale module testing systems capable of probing flow dynamics, and small pilot-scale skid rooms able to test prototype DAC units under a wide variety of climate conditions. The NETL DAC Center will feature dedicated engineering, technician, scientific and logistical support for experimental system design, installation, operation of experiments, and interpretation of results for projects including but not limited to kinetics of absorption/desorption, thermal duty, and post-mortem elemental characterization to understand degradation. The NETL DAC Center projects will also have access to dedicated process modeling and analysis to evaluate the technoeconomic aspects of new technologies. NETL’s Systems Engineering and Analysis (SEA) team, the Carbon Capture Simulation Initiative (CCSI), and the Institute for the Design of Advanced Energy Systems (IDAES) are all potential collaborators with NETL’s testing partners from industry, academia, and other research institutions. NETL also has world class capabilities in device scale modeling (i.e., MFIX) that will be available to help design more efficient contactors and optimize unique internal configurations that can be realized by advanced manufacturing. The talk will cover the design and capabilities of the center, the planned availability, and feedback will be solicited from the audience on DAC testing needs.

Luebke, David↗

DOE OSTI2023

Accelerating commercialization of direct air capture technology

Luebke, David↗

NASA NTRSDate not supplied

Investigating Material Behavior in Atmospheric Entry Conditions: Arc-Jet Testing Insights from Meteorite Ablation to High-Temperature Coatings.

Arc-jet testing is an indispensable tool in elucidating the complex interactions materials undergo when subjected to the extreme thermal and mechanical stresses of atmospheric entry. By replicating these harsh conditions, arc-jets enable researchers to explore critical phenomena such as ablation, melting, and spallation, generating invaluable data that informs the development of sophisticated, physics-based models. These models are pivotal not only in predicting material performance for spacecraft re-entry systems but also in assessing the threat posed by celestial bodies as they encounter Earth’s atmosphere. One of the leading facilities for such investigations is the Hypersonic Materials Environmental Test System (HyMETS) at NASA’s Langley Research Center. A pioneering test campaign conducted at HyMETS focused on unraveling the ablation mechanisms of an ordinary chondrite meteorite (Tamdakht H5) and a terrestrial analog (basalt). These studies unveiled distinct material behaviors: Tamdakht demonstrated a remarkably stable melt flow, with mass loss primarily driven by the volatilization of elements such as iron and sodium, whereas basalt exhibited more aggressive surface degradation due to the rapid decomposition of hydrated minerals, culminating in significant spallation and surface material ejection. Beyond meteorite analysis, HyMETS has also been integral in the exploration of advanced Thermal Protection Systems (TPS) such as Phenolic Impregnated Carbon Ablator (PICA), a material with extensive flight heritage in missions like Stardust, Mars Science Laboratory, Mars 2020, and Osiris-REx. PICA, when coated with NuSil CV-1144-0—a polysiloxane resin designed to prevent particle shedding—undergoes a remarkable transformation upon heating. The resin pyrolyzes to form a thin, oxidation-resistant silicon oxycarbide layer that profoundly influences the material’s thermal response through a sophisticated four-stage process. Initially, the silicon oxycarbide acts as a formidable barrier, impeding reactive interactions with the PICA char and effectively suppressing surface temperature rise and material recession. However, as the heating persists, the protective layer decomposes via carbothermal reduction, exposing the underlying char, which in turn leads to a dramatic spike in surface temperature and accelerated material erosion. In the final stage, equilibrium is reached, with recession rates aligning with those of the virgin material. This intricate understanding of PICA-NuSil behavior under extreme conditions offers valuable insights, enhancing material response models and advancing the development of next-generation TPS for space exploration.

Chemistry↗