Search NASA⌕ Search

SEARCH · Search NASA

Results for “array data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Output data formatter for the Electronically Scanned Thinned Array Radiometer (ESTAR) instrument

A prototype Output Data Formatter (ODF) for the ESTAR (Electronically Scanned Thinned Array Radiometer) instrument has been designed and tested. It employs programmable logic devices to format and tag correlator data for transmission to Earth. After accepting 170 bits or correlator and error data in parallel, it appends an identification word and then serially passes the data to the Small Explorer Data System (SEDS) for transmission at a maximum rate of greater than 15 Mb/sec. Implemented with two reprogrammable field programmable gate arrays (FPGA's), each contained in a 132-pin plastic pin grid array (PGA) package, the design is cascadeable, fully testable, and low-power.

Chren, William A., Jr.↗

The Impact of Local Meteorological Conditions on Airframe Noise Flight Test Data

Phased microphone array measurements obtained during flight tests conducted in 2016 and 2017 are used to assess the importance of local meteorological measurements on the data. In particular, the effectiveness of atmospheric absorption corrections is evaluated under vastly different temperature and humidity conditions. The results indicate that, even under conditions with high absorption, sources can be visualized up to a frequency that is dependent on background noise levels, wind, and atmospheric turbulence. However, absolute levels were found to be problematic on days with high absorption rates, with the discrepancies most prevalent for aircraft positions further from the center of the array. Restricting the data to those days with favorable meteorological conditions generally resulted in a good collapse of the spectra, with differences less than a couple of decibels.

Lockard, David P.↗

Multispectral imaging and analysis system

Arrays of charge coupled devices or linear detector arrays simultaneously obtain spectral reflectance data of different wavelengths for a target area. Several accommodating a particular bandwidth, are individually associated with each array. Data from the arrays are read out in parallel and applied to a computer or microprocessor for processing. The microprocessor serves to analyze the data in real time and if possible, in accordance with hard-wired algorithms. The data are then displayed as an image on an appropriate display unit and also recorded for further use. The display system may be operationally connected to receive a terrain image such that the target area and the analyzed spectral reflectance data are superimposed and simultaneously displayed.

Goetz, A. F. H.↗

One GigaSample Per Second Data Acquisition using Available Gate Array Technology

A new National Aeronautics and Space Administration instrument forced demanding requirements upon its altimeter digitizer system. Eight-bit data would be generated at a rate of one billion samples per second. NASA had never before attempted to capture such high-speed data in the radiation, low-power, no-convective-cooling, limited-board-area environment of space. This presentation describes how the gate array technology available at the time of the design was used to implement this one gigasample per second data acquisition system

Wagner, K.W.↗

Glasses for Solar-Cell Arrays

Report presents data on glass for encapsulation of solar-cell arrays, with special emphasis on materials and processes for automated high-volume production of low-cost arrays. Commercial suppliers of glass are listed. Factors that affect the cost of glass are examined: type (sheet, float, or plate), formulation, and energy consumed in manufacturing.

Bouquet, F. L.↗

ISS Solar Array Management

The International Space Station (ISS) Solar Array Management (SAM) software toolset provides the capabilities necessary to operate a spacecraft with complex solar array constraints. It monitors spacecraft telemetry and provides interpretations of solar array constraint data in an intuitive manner. The toolset provides extensive situational awareness to ensure mission success by analyzing power generation needs, array motion constraints, and structural loading situations. The software suite consists of several components including samCS (constraint set selector), samShadyTimers (array shadowing timers), samWin (visualization GUI), samLock (array motion constraint computation), and samJet (attitude control system configuration selector). It provides high availability and uptime for extended and continuous mission support. It is able to support two-degrees-of-freedom (DOF) array positioning and supports up to ten simultaneous constraints with intuitive 1D and 2D decision support visualizations of constraint data. Display synchronization is enabled across a networked control center and multiple methods for constraint data interpolation are supported. Use of this software toolset increases flight safety, reduces mission support effort, optimizes solar array operation for achieving mission goals, and has run for weeks at a time without issues. The SAM toolset is currently used in ISS real-time mission operations.

Williams, James P.↗

Hydrostar Thermal and Structural Deformation Analyses of Antenna Array Concept

The proposed Hydrostar mission used a large orbiting antenna array to demonstrate synthetic aperture technology in space while obtaining global soil moisture data. In order to produce accurate data, the array was required to remain as close as possible to its perfectly aligned placement while undergoing the mechanical and thermal stresses induced by orbital changes. Thermal and structural analyses for a design concept of this antenna array were performed. The thermal analysis included orbital radiation calculations, as well as parametric studies of orbit altitude, material properties and coating types. The thermal results included predicted thermal distributions over the array for several cases. The structural analysis provided thermally-driven deflections based on these cases, as well as based on a 1-g inertial load. In order to minimize the deflections of the array in orbit, the use of XN70, a carbon-reinforced polycyanate composite, was recommended.

Amundsen, Ruth M.↗

Translating Phased Array Measurements of a Low-Noise Top-Mounted Propulsion Installation for a Supersonic Airliner

A novel translating-phased-array technique was applied during a model-scale validation test of low-noise propulsion concepts for supersonic transport aircraft. The test involved particle image velocimetry, far field and translating phased array acoustic measurements. This paper covers the translating phased array portion. Data were acquired for a series of nozzles with different chevron designs, both uninstalled and installed on a representative aircraft planform. The far field data confirmed the noise reduction potential of top-mounted installation, while the phased array results gave insights into how the reduction occurred and highlighted areas for improvement. This was the inaugural test for the new translating phased array, which measures source maps as seen by observers at different polar angles. Propagation effects through the free jet were documented for the different viewing angles. The source maps obtained were used to understand important aspects of the far field noise measurements.

Beamforming↗

Thermal Cycling of Mir Cooperative Solar Array (MCSA) Test Panels

The Mir Cooperative Solar Array (MCSA) project was a joint US/Russian effort to build a photovoltaic (PV) solar array and deliver it to the Russian space station Mir. The MCSA is currently being used to increase the electrical power on Mir and provide PV array performance data in support of Phase 1 of the International Space Station (ISS), which will use arrays based on the same solar cells used in the MCSA. The US supplied the photovoltaic power modules (PPMs) and provided technical and programmatic oversight while Russia provided the array support structures and deployment mechanism and built and tested the array. In order to ensure that there would be no problems with the interface between US and Russian hardware, an accelerated thermal life cycle test was performed at NASA Lewis Research Center on two representative samples of the MCSA. Over an eight-month period (August 1994 - March 1995), two 15-cell MCSA solar array 'mini' panel test articles were simultaneously put through 24,000 thermal cycles (+80 C to -100 C), equivalent to four years on-orbit. The test objectives, facility, procedure and results are described in this paper. Post-test inspection and evaluation revealed no significant degradation in the structural integrity of the test articles and no electrical degradation, not including one cell damaged early as an artifact of the test and removed from consideration. The interesting nature of the performance degradation caused by this one cell, which only occurred at elevated temperatures, is discussed. As a result of this test, changes were made to improve some aspects of the solar cell coupon-to-support frame interface on the flight unit. It was concluded from the results that the integration of the US solar cell modules with the Russian support structure would be able to withstand at least 24,000 thermal cycles (4 years on-orbit).

Hoffman, David J.↗

A Spatially Coherent Global Soil Moisture Product with Improved Temporal Resolution

Global soil moisture products that are completely independent of any type of ancillary data and solely rely on satellite observations are presented. Additionally, we further develop an existing downscaling technique that enhances the spatial resolution of such products to approximately 11 km. These products are based on internal modules of the Land Parameter Retrieval Model (LPRM), an algorithm that uses the radiative transfer equation to link soil moisture, vegetation optical depth and land surface temperature to observed brightness temperatures. The soil moisture product that is independent of any type of ancillary data uses the internally calculated dielectric constant as a soil moisture proxy. This data product is not influenced by errors associated with coarse-scale global soil property maps or by any other type of forcing (e.g. re-analysis) data and is therefore solely based on satellite microwave observations. The second step builds upon recent developments to increase the spatial resolution of the LPRM retrievals using a smoothing filter downscaling method. With this method we can attain a spatial resolution that can be more useful at the scale of local and regional hydrological studies as well. The steps presented in this paper were applied to observations from the Advanced Microwave Scanning Radiometer-Earth Observing System (AMSR-E). The newly derived data sets were validated using ground-based observations from the International Soil Moisture Network (ISMN). The internally calculated dielectric constant product results in significantly more days with valid retrievals than the original soil moisture data products, in particular over arid regions. The dielectric constant product resulted in similar correlations with in situ data as the original soil moisture data product. Together, these findings demonstrate the usefulness of this new dielectric constant product for the hydrological modeling community and climate studies. A case study on the Australian Fitzroy catchment demonstrated that the downscaled data product has a more detailed spatial description of soil moisture, especially during wet and dry conditions with more pronounced dry and wet regions within the catchment. The increased resolution data products could therefore improve runoff predictions and this study demonstrated the potential added value of a transitioning from a spatial resolution of 56 km toward a higher resolution of 11 km. The hydrological implications of these newly developed data records are not only linked to AMSR-E satellite data, but also to the next generation Soil Moisture Active and Passive (SMAP) mission where a 9 km spatial resolution is the target resolution for satellite soil moisture products. The new data products will not replace the current LPRM products, but will be added to the existing array of data products and will become publicly available through our data portals.

spatial↗

Performance of the QWIP Focal Plane Arrays for NASA's Landsat Data Continuity Mission

The focal plane assembly for the Thermal Infrared Sensor (TIRS) instrument on NASA's Landsat Data Continuity Mission (LDCM) consists of three 512 x 640 GaAs Quantum Well Infrared Photodetector (QWIP) arrays. The three arrays are precisely mounted and aligned on a silicon carrier substrate to provide a continuous viewing swath of 1850 pixels in two spectral bands defined by filters placed in close proximity to the detector surfaces. The QWIP arrays are hybridized to Indigo ISC9803 readout integrated circuits (ROICs). QWIP arrays were evaluated from four laboratories; QmagiQ, (Nashua, NH), Army Research Laboratory, (Adelphi, MD}, NASA/ Goddard Space Flight Center, (Greenbelt, MD) and Thales, (Palaiseau, France). All were found to be suitable. The final discriminating parameter was the spectral uniformity of individual pixels relative to each other. The performance of the QWIP arrays and the fully assembled, NASA flight-qualified, focal plane assembly will be reviewed. An overview of the focal plane assembly including the construction and test requirements of the focal plane will also be described.

Jhabvala, M.↗

Analysis of upper mantle structure using wave field continuation of P waves

Wave field continuation theory, which allows transformation of the seismic record section data directly into velocity-depth space, is tested for upper mantle analysis using a large array-recorded data set obtained at the 200-station Caltech-USGS Southern California Seismic Network that is representative of the structure beneath the gulf of California. The method's resolution capability is illustrated by the comparison of the slant stacks and downward continuation of both synthetic and data record sections. It is stressed that when high-quality, densely sampled digital data are available, the technique is easy to implement, provides an inversion which contains all the data in the global format, and produces an objective estimate of depth resolution as a function of ray parameter.

Walck, M. C.↗

GADB: A database facility for modelling naturally occurring geophysical fields

In certain kinds of geophysical surveys, the fields are continua, but measured at discrete points referenced by their position or time of measurement. Systems of this kind are better modelled by databases built from basic data structures attuned to representing traverses across continua that are not of pre-defined fixed length. The general Array DataBase is built on arrays (ordered sequencies of data) with each array holding data elements of one type. The arrays each occupy their own physical data set, in turn inter-related by a hierarchy to other arrays over the same space/time reference points. The GADB illustrates the principle that a data facility should reflect the fundamental properties of its data, and support retrieval based on the application's view. The GADB is being tested by its use in NASA's project MAGSAT.

Dampney, C. N. G.↗

DUMAND Summer Workshop, University of California, La Jolla, Calif., July 24-September 2, 1978, Proceedings. Volume 1 - Array studies

Papers are presented concerning the design and implementation of the optical and acoustic sensors that will comprise the DUMAND (Deep Underwater Muon and Neutrino Detector) array. Specific topics include the results of experiments on atmospheric muon and neutrino spectra obtained with various muon and neutrino spectrometers, optical sensors and arrays, optical data handling systems, the simulation of the sound generated by high-energy particles in water, constraints on acoustic arrays, standard ocean parameters for DUMAND calculations, and Monte Carlo investigations of hadronic and electromagnetic cascades in sea water.

Roberts, A.↗

BIOME: A browser-aware search and order system

The Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC), which is associated with NASA's Earth Observing System Data and Information System (EOSDIS), provides access to a large number of tabular and imagery datasets used in ecological and environmental research. Because of its large and diverse data holdings, the challenge for the ORNL DAAC is to help users find data of interest from the hundreds of thousands of files available at the DAAC without overwhelming them. Therefore, the ORNL DAAC developed the Biogeochemical Information Ordering Management Environment (BIOME), a search and order system for the World Wide Web (WWW). The WWW provides a new vehicle that allows a wide range of users access to the data. This paper describes the specialized attributes incorporated into BIOME that allow researchers easy access to an otherwise bewildering array of data products.

Grubb, Jon W.↗

Recent Excitation, Charge Exchange, and Lifetime Results in Highly Charged Ions Relevant to Stellar, Interstellar, Solar and Comet Phenomena

Recent JPL absolute excitation and charge exchange cross sections, and measurements of lifetimes of metastable levels in highly-charged ions (HCIs) are reported. These data provide benchmark comparisons to results of theoretical calculations. Theoretical approaches can then be used to calculate the vast array of data which cannot be measured due to experimental constraints. Applications to the X-ray emission from comets are given.

Chutjian, A.↗

NH3, H2S, and the Radio Brightness Temperature Spectra of the Giant Planets

Recent radio interferometer observations of Neptune enable comparisons of the radio brightness temperature (T(sub B)) spectra of all four giant planets. This comparison reveals evidence for fundamental differences in the compositions of Uranus' and Neptune's upper tropospheres, particularly in their ammonia (NH3) and hydrogen sulfide (H2S) mixing ratios, despite those planets' outward similarities. The tropospheric abundances of these constituents yield information about their deep abundances, and ultimately about the formation of the planets from the presolar nebula (Atreya et al.). Figures 1, 2, 3, and 4 show the T(sub B) spectra of Jupiter, Saturn, Uranus, and Neptune, respectively, from 0.1 to tens of cm wavelength. The data shown are collected from many observers. Data for Jupiter, Saturn, and Uranus are those cataloged by de Pater and Massie (1985), plus the Saturn Very Large Array (VLA) data by Grossman et al. Figure 3, Uranus, shows only data acquired since 1973. Before 1973 Uranus' T(sub B) increased steadily as its pole moved into view, causing significant scatter in those data. Neptune data at greater than 1 cm, all taken at the VLA, are collected from de Pater and Richmond, de Pater et al., and Hofstadter. For a variety of reasons, such as susceptibility to source confusion, single-dish data at those wavelengths are much noisier than the more reliable VLA data and have been ignored. Single-dish data by Griffin and Orton shortward of 0.4 cm are shown, along with the Owens Valley Radio Observatory (interferometer) datum at 0.266 cm by Muhleman and Berge. Spectra of Jupiter, Saturn, and Neptune share certain gross characteristics. In each spectrum, T(sub B) at 1.3 cm is approximately 120-140 K, less than approximately 30 K different from that at 0.1 cm. All three spectra show a break in slope at or near 1.3 cm, with T(sub B) increasing fairly rapidly with wavelength longward of 1.3 cm. Visible and IR spectroscopy show that NH3, whose strong inversion spectrum peaks at appropximately 1.3 cm, is an important tropospheric species at Jupiter and Saturn. Its signature on the Jovian radio spectrum is obvious, causing the prominent "hole" at 1.3 cm. At Saturn it is more subdued but is the source of that spectrum's change in slope at 1.3 cm. Radiative transfer models of Jupiter and Saturn with near-solar deep NH3 abundances agree well with the data (e.g., de Pater).

Spilker, Thomas R.↗

An Update on Phased Array Results Obtained on the GE Counter-Rotating Open Rotor Model

Beamform maps have been generated from 1) simulated data generated by the LINPROP code and 2) actual experimental phased array data obtained on the GE Counter-rotating open rotor model. The beamform maps show that many of the tones in the experimental data come from their corresponding Mach radius. If the phased array points to the Mach radius associated with a tone then it is likely that the tone is a result of the loading and thickness noise on the blades. In this case, the phased array correctly points to where the noise is coming from and indicates the axial location of the loudest source in the image but not necessarily the correct vertical location. If the phased array does not point to the Mach radius associated with a tone then some mechanism other than loading and thickness noise may control the amplitude of the tone. In this case, the phased array may or may not point to the actual source. If the source is not rotating it is likely that the phased array points to the source. If the source is rotating it is likely that the phased array indicates the axial location of the loudest source but not necessarily the correct vertical location. These results indicate that you have to be careful in how you interpret phased array data obtained on an open rotor since they may show the tones coming from a location other than the source location. With a subsonic tip speed open rotor the tones can come form locations outboard of the blade tips. This has implications regarding noise shielding.

Podboy, Gary↗