SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
By adding potential energy of charged capacitor to kinetic energy of impacting particle, new technique causes major fraction of atoms in microscopic particle impacting on particle-receiving surface to be ionized. Chemical constituents of impacting particle are represented by generated ion mass spectrum in approximately correct proportions.
Thermospheric energetics is examined from the point of view of atomic and molecular processes which convert solar EUV radiative energy into kinetic energy of the ambient electron, ion, and neutral gases. The energy flow from photon to photoelectron-ion pair through energy loss and ion-molecule transfer to eventual electron-ion recombination is traced in detail. Upper and lower bounds are placed on the efficiency of conversion of radiative to thermal energy. Implications for the question of consistency of measured solar EUV fluxes and ionospheric models are discussed.
Species dependent kinetic, transport and thermodynamic coefficients were employed in a one dimensional model of the premixed, laminar, steady state ozone flame. Convenient expressions for these coefficients are reported. They are based on independent measurements, no arbitrary parameters are used. The governing equations are solved using a relaxation technique and the partial differential equation package, PDECOL. Species and temperature profiles and the burning velocities are found over the range of initial ozone mole fraction of 0.25 to 1.00. The computed burning velocities are no more than 30% greater than the measurements of Streng and Grosses. Comparison with the computed results of Warnatz shows agreement within + or - 12%, even though quite different expressions for some of the kinetic coefficients were used. These differences are most obvious in the atomic oxygen and temperature profiles at an initial ozone mole fraction of unity.
Reactor loading has an effect on the etch rate (rate of decrease of film thickness) of films of polyvinylfluoride (Tedlar) and polyethylene exposed in the afterglow of an RF discharge in oxygen. The etch rate is found to increase with the total surface area of the polymer exposed in the reactor. The etch rates of polypyromellitimide (Kapton H) and polystyrene under these conditions are very low. However, the etch rate of these polymers is greatly enhanced by adding either Tedlar or polyethylene to the reactor. A kinetic model is proposed based on the premise that the oxygen atoms produced by the RF discharge react with Tedlar or polyethylene to produce a much more reactive species, which dominates the etching of the polymers studied.
Time-resolved resonance fluorescence detection of Br((sup 2)P(sub 3/2)) atom disappearance or appearance 266 nm laser flash photolysis of CF2Br2/CH3SCH3/H2/N2 and Cl2CO/CH2SCH3/HBr/H2/N2 mixtures has been employed to study the kinetics of the reactions Br((sup 2)P(sub 3/2)) + CH3SCH3 reversible reaction HBr + CH3SCH2 (1,-1) as a function of temperature over the range 386-604 K. Arrhenius expressions in units of cu cm/molecule which describe the results are k3= (9.0 +/- 2.9) x 10 (exp -11) exp[(-2386 +/- 151)/T]; errors are 2 sigma and represent precision only. To our knowledge, these are the first kinetic data reported for each of the two reactions studied. Second and third law analyses of the equilibrium data for reactions 1 and -1 have been employed to obtain the following enthalpies of reaction in units of kcal/mol: Delta-H(298) = 6.11 +/- 1.37 and Delta-H(0) = 5.37 +/- 1.38. Combining the above enthalpies of reaction with the well-known heats of formation of Br, HBr, CH3SCH3 gives the following heats of formation of the CH3SCH2 radical in units of kcal/mol: Delta-H(sub(f,298)) = 32.7 +/- 1.4 and Delta-H(sub (f,0)) = 35.3 +/- 1.4; errors are 2 sigma and represent estimates of absolute accuracy. The C-H bond dissociation energy in CH3SCH3 obtained from our data, 93.7 +/- 1.4 kcal/mol at 298 K and 92.0 +/- 1.4 kcal at 0 k, agrees well with a recent molecular beam photofragmentaion study but is 3 kcal/mol lower than the value obtained from an iodination kinetics study.
Horse spleen ferritin (HoSF) containing 800-1500 cobalt or 250-1200 manganese atoms as Co(O)OH and Mn(O)OH mineral cores within the HoSF interior (Co-HoSF and Mn-HoSF) was synthesized, and the chemical reactivity, kinetics of reduction, and the reduction potentials were measured. Microcoulometric and chemical reduction of HoSF containing the M(O)OH mineral core (M = Co or Mn) was rapid and quantitative with a reduction stoichiometry of 1.05+/-0.10 e/M forming a stable M(OH)2 mineral core. At pH 9.0, ascorbic acid (AH2), a two-electron reductant, effectively reduced the mineral cores; however, the reaction was incomplete and rapidly reached equilibrium. The addition of excess AH2 shifted the reaction to completion with a M(3+)/AH2 stoichiometry of 1.9-2.1, consistent with a single electron per metal atom reduction. The rate of reaction between M(0)OH and excess AH2 was measured by monitoring the decrease in mineral core absorbance with time. The reaction was first order in each reactant with second-order rate constants of 0.53 and 4.74/M/min, respectively, for Co- and Mn-HoSF at pH 9.0. From the variation of absorbance with increasing AH2 concentration, equilibrium constants at pH 9.0 of 5.0+/-1.9 for Co-HoSF and 2.9+/-0.9 for Mn-HoSF were calculated for 2M(O)OH + AH2 = 2M(OH)2 f D, where AH2 and D are ascorbic acid and dehydroascorbic acid, respectively. Consistent with these equilibrium constants, the standard potential for the reduction of Co(III)-HoSF is 42 mV more positive than that of the ascorbic acid reaction, while the standard potential of Mn(III)-HoSF is 27 mV positive relative to AH2. Fe(2+) in solution with Co- and Mn-HoSF under anaerobic conditions was oxidized to form Fe(O)OH within the HoSF interior, resulting in partial displacement of the Co or Mn by iron.
A major challenge in understanding differences in electric propulsion performance in ground tests and in space operations concerns the pressure distribution within the test vacuum chamber. The chamber backpressure is much higher than experienced in space, modifying thruster performance and plume dynamics. Numerical simulation is a key element to determining the background conditions in non-ideal vacuum chamber environments. An important parameter for the accurate simulation of chamber backpressure is the probability that an atom will stick to a cryogenic panel used to pump away the plume gases. This quantity can be used to model vacuum pumps in particle-based kinetic numerical methods. In this work, a three-dimensional direct simulation Monte Carlo code is used to model neutral xenon atoms flowing from the anode of the H9 Hall Effect Thruster within the University of Michigan’s Large Vacuum Test Facility. Simulated pressures are compared with ion gauge pressure measurements to infer the effective sticking coefficient of the chamber’s vacuum pumps. A pressure predicting surrogate model is developed for inference of pump sticking coefficients and for uncertainty quantification. This information enables accurate and useful kinetic simulations of electric propulsion thruster plasma plumes in vacuum chambers.
The 6300 A O(1D-3P) emission has been used for many years to remotely monitor the thermospheric temperature from the Doppler width of its line profile. The O(1D) atoms in the nighttime thermosphere are initially produced by the dissociative recombination of O2(+) ions with kinetic energy much greater than the thermal energy of the ambient neutrals. The validity of the technique to monitor neutral ambient temperature by measuring O(1D) 6300 A emission depends on the degree of thermalization of the O(1D) atoms. The object of this study is to calculate the velocity distribution of the O(1D) atoms and to examine the effect of nonthermal distribution on the nighttime thermospheric neutral temperature determined.
Rate constants for excitation of water molecules by collisions with He atoms have been obtained from extensive theoretical calculations. For ortho-H2O, rates are presented for all spectroscopic levels below 1000/cm and for kinetic temperatures to 500 K; for para-H2O, levels below 300/cm and kinetic temperatures to 250 K are included. It is suggested that rates of excitation by collisions with hydrogen molecules are similar to those for He atoms.
A highly polarized (P = 0.48 + or - 0.02) intense (500,000/sec) beam of 'slow' (Delta E = about 2 eV) positrons (e+) is generated, and it is shown that it is possible to achieve polarization as high as P = 0.69 + or - 0.04 with reduced intensity. The measured polarization of the slow e+ emitted by five different positron moderators showed no dependence on the moderator atomic number (Z). It is concluded that only source positrons with final kinetic energy below 17 keV contribute to the slow-e+ beam, in disagreement with recent yield functions derived from low-energy measurements. Measurements of polarization and yield with absorbers of different Z between the source and moderator show the effects of the energy and angular distributions of the source positrons on P. The depolarization of fast e+ transmitted through high-Z absorbers has been measured. Applications of polarized slow-e+ beams are discussed.
Several techniques are discussed which can be used to explore laboratory photochemical processes and kinetics relevant to planetary atmospheres; these include time-resolved laser gain-versus-absorption spectroscopy and time-resolved Fourier transform infrared (FTIR) emission studies. The laser gain-versus-absorption method employed tunable diode and F-center lasers to determine the yields of excited photofragments and their kinetics. The time-resolved FTIR technique synchronizes the sweep of a commercial FTIR with a pulsed source of light to obtain emission spectra of novel transient species in the infrared. These methods are presently being employed to investigate molecular photodissociation, the yields of excited states of fragments, their subsequent reaction kinetics, Doppler velocity distributions, and velocity-changing collisions of translationally fast atoms. Such techniques may be employed in future investigations of planetary atmospheres, for example to study polycyclic aromatic hydrocarbons related to cometary emissions, to analyze acetylene decomposition products and reactions, and to determine spectral features in the near infrared and infrared wavelength regions for planetary molecules and clusters.
Since electrons travel over 100 times faster in Silicon-Germanium (SiGe) than in pure Si due to the low effective masses associated with Ge and SiGe-based devices continue to replace Si-based solid-state electronic devices. SiGe thin film on sapphire was successfully grown at 890°C, using a magnetron sputtering system within heteroepitaxial framework. However, SiGe growth at 890oC is a costly and difficult process to produce as a uniform wafer for semiconductor device manufacturing due to thermal soak times, and geometric thermal shadowing from the wafer holder. To leverage the semiconducting capabilities of SiGe, novel processing techniques for SiGe film growth with decreased thermal loading are required. This paper introduces the Molten Target Sputtering (MTS) method that produces high mobility SiGe on sapphire below 500°C. This non-conventional method has the advantage of high kinetic energy, high-energy latency, and high flux density of sputtered atoms by combining benefits of both magnetron sputtering and thermal evaporation. For the MTS method, a 1~2 mm (depth and width) ring-shaped groove was cut between the center magnet and surrounded by electromagnets creating a circular cavity between the copper plate and source target materials that melt the target material. The SiGe grown from the MTS shows continuous morphology and 99.7% single crystal Si0.15Ge0.85 films. The Hall electron mobilities of the Si0.15Ge0.85 are 456 sq. cmV(exp -1)s(exp -1) and 123.9 sq. cmV(exp -1)s(exp -1) at 5.59 x 10(exp 18) cubic cm and 3.5 x 10(exp 20) cubic cm carrier concentration at 22.38°C, respectively. This is approximately 5.5 times higher than that of Si and similar to the Ge value at equivalent carrier concentrations and temperatures.
The stoichiometric combustion of propane behind incident shock waves was studied experimentally and analytically over a temperature range from 1700 K to 2600 K and a pressure range from 1.2 to 1.9 atm. Measurements of the concentrations of carbon monoxide (CO) and carbon dioxide (CO2) and the product of the oxygen atom and carbon dioxide concentrations (O)(CO) were made after passage of the incident shock wave. A kinetic mechanism was developed which, when used in a computer program for a flowing, reacting gas behind an incident shock wave predicted experimentally measured results quite well. Ignition delay times from the literature were also predicted quite well. The kinetic mechanism consisted of 59 individual kinetic steps.
It is pointed out that the investigated reaction of oxygen with dimethyl sulfide may play an important role in photochemical smog formation and in the chemical evolution of dense interstellar clouds. Kinetic data were obtained with the aid of the flash photolysis-resonance fluorescence method. The photodecomposition of molecular oxygen provided the oxygen atoms for the experiments. The decay of atomic oxygen was studied on the basis of resonance fluorescence observations. Both reactions investigated were found to be fast processes. A negative temperature dependence of the rate constants for reactions with dimethyl sulfide was observed.
Photolysis experiments were performed on the H2-CD4-NH3 and He-CD4-NH3 systems. The photolysis (1849 A) involved only NH3. Mixtures of H2:CD4:NH3 included all combinations of the ratios (200,400,800):(10,20,40):4. Two He:CD4:NH3 mixtures were examined where the ratios equalled the combinations 100:(10,20):4. Abstraction of a D from CD4 by the photolytically produced hot hydrogen from ammonia was monitored by mass spectrometric determination of HD. Both experiment and semiempirical hot-atom theory show that H2 is a very poor thermalizer of hot hydrogens with excess kinetic energy of about 2 eV. Applications of the hard-sphere collision model to the H2-CD4-NH3 system resulted in predicted ratios of net HD production to NH3 decomposition that were two orders of magnitude smaller than the experimental ratios. On the other hand, helium is found to be a very efficient thermalizer; here, the classical model yields reasonable agreement with experiments. Application of a semiempirical hot-atom program gave quantitative agreement with experiment for either system.
The temperature dependence of two chlorine atom reactions of considerable fundamental importance to stratospheric chemistry was studied using the technique of flash photolysis-resonance fluorescence. The reactions of interest were: (1) Cl + O3 yields ClO + O2 studied at 220-350 K, and (2) Cl + CH4 yields CH3 + HCl studied at 218-401 K. In addition, the reaction Cl + H2O2 yields HCl + HO2 was studied at 300 K. The corresponding rate constants are provided for the three reactions. The new rate data implies the need to revise downward by a factor of 2.4-3 the magnitude of the ozone perturbation due to the presence of ClO/x/ species in the stratosphere, predicted by earlier model calculations.
Time resolved resonance fluorescence detection of Br(sup 2)P3/2) atom disappearance or appearance following 266-nm laser flash photolysis of CF2Br2/H2S/H2/N2, CF2Br2/CH3SH/H2/N2, Cl2CO/H2S/HBr/N2, and CH3SSCH3/HBr/H2/N2 mixtures has been employed to study the kinetics of the reactions Br((sup 2)P3/2) + H2S = SH + HBr (1,-1) and Br((sup2)P3/2) + CH3SH = CH3S + HBr (2, -2) as a function of temperature over the range 273-431K. Arrhenius expressions in units of 10(exp -12) cu cm/molecule/s which describe the results are k1 = (14.2 +/- 3.4) exp[(-2752 +/- 90)/T],(k-1) = (4.40 +/- 0.92) exp[(-971 +/- 73)/T],k(2) = (9.24 +/- 1.15) exp[(-386 +/- 41)/T], and k(-2) = (1.46 +/-0.21) exp[(-399 +/-41)/T; errors are 2 sigma and represent precision only. By examining Br((sup 2)P3/2) equilibrium kinetics following 355nm laser flash photolysis of Br2/CH3SH/H2/N2 mixtures, a 298 K rate coefficient of (1.7 +/- 0.5) x 10(exp -10) cu cm/molecule/s has been obtained for the reaction CH3S + Br2 yields CH3SBr + Br. To our knowledge, these are the first kinetic data reported for each of the reactions studied. Measured rate coefficients, along with known rate coefficients for similar radical + H2S, CH3SH, HBr,Br2 reactions are considered in terms of possible correlations of reactivity with reaction thermochemistry and with IP - EA, the difference between the ionization potential of the electron donor and the electron affinity of the electron acceptor. Both thermochemical and charge-transfer effects appear to be important in controlling observed reactivities. Second and third law analyses of the equilibrium data for reactions 1 and 2 have been employed to obtain the following enthalpies of reaction in units of kcal/mol: for reaction 1, Delta-H(298) = 3.64 +/- 0.43 and Delta-H(0) = 3.26 +/-0.45; for reaction 2, Delta-H(298) = -0.14 +/- 0.28 and Delta-H(0) = -0.65 +/- 0.36. Combining the above enthalpies of reaction with the well-known heats of formation of Br, HBr, H2S, and CH3SH gives the following heats of formation for the RS radicals in units of kcal/mol: Delta-H(sub f)(sub 0)(SH) = 34.07 +/- 0.72, Delta-H(sub f)(sub 298)(SH) = 34.18 +/- 0.68, Delta-H(sub f)(sub 0)(CH3S) = 31.44 +/- 0.54, Delta-H(sub f)(sub 298)(CH3S) = 29.78 +/- 0.44; errors are 2 sigma and represent estimates of absolute accuracy. The SH heat of formation determined from our data agrees well with literature values but has reduced error limits compared to other available values. The CH3S heat of formation determined from our date is near the low end of the range of previous estimates and is 3-4 kcal/mol lower than values derived from recent molecular beam photofragmentation studies.
The search for a new high-modulus, high-temperature glass fiber involved the preparation of 500 glass compositions lying in 12 glass fields. These systems consisted primarily of low atomic number oxides and rare-earth oxides. Direct optical measurements of the kinetics of crystallization of the cordierite-rare earth system, for example, showed that the addition of rare-earth oxides decreased the rate of formation of cordierite crystals. Glass samples prepared from these systems proved that the rare-earth oxides made large specific contributions to the Young's modulus of the glasses. The best glasses have moduli greater than 21 million psi, the best glass fibers have moduli greater than 18 million psi, and the best glass fiber-epoxy resin composites have tensile strengths of 298,000 psi, compressive strengths of at least 220,000 psi, flexural strengths of 290,000 psi, and short-beam shear strengths of almost 17,000 psi.