The charge-storage diode as a subharmonic generator.
Optimum tuning of charge-storage diode as subharmonic generator occurs on verge of instability, consistent with Manley-Rowe theory
SUBHARMONIC OSCILLATOR↗
SEARCH · Search NASA
Results for “charge generation”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Photoinjector Generation of High-Charge Magnetized Beams for Electron-Cooling Applications
Electron-cooling offers a relatively simple scheme to enable high-luminosity collisions in future electron-ion and hadron colliders. Contemplated TeV-energy hadron colliders require relativistic (sub 100 MeV) high-charge [${\cal O}(\mbox{nC})$] electron beams with a specific transverse eigenemittance partition. This paper discusses the generation of high-charge ($Q\le 3.2$~nC) 40 MeV electron bunches with eigenemittance partition consistent with requirements associated with electron-cooling option for future electron-ion colliders. The supporting experiment was performed at the FAST facility at FermiLab. The data are compared with numerical simulations and the results discussed in the context of beam requirement for future electron-ion colliders.
43 PARTICLE ACCELERATORS↗
Chemo-Mechanical Instabilities in Lithium Cobalt Oxide at Higher State-Of-Charge in Li-Ion Batteries
Transition metal oxide cathodes are widely used in commercial Li-ion batteries. However, their practical charge capacity is limited due to severe chemo-mechanical instabilities at higher charge voltage, and state-of-charge condition. Here, in situ stress and strain measurements were synchronized to probe mechanical deformations in the lithium cobalt oxide (LCO) cathode via a multi-beam stress sensor and digital image correlation, respectively. In situ mechanical measurements revealed how Li removal from the electrode structure induces deformations on the LCO composite cathodes during cycling. The structure and morphology of the LCO cathodes were further investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM) studies. Two distinct electrochemical and mechanical behaviors were identified when the LCO was charged up to 4.65 V. The LCO undergoes a compressive stress generation when charged up to 4.2 V and surface fractures on the LCO particles were detected by SEM. LCO cathode experienced significantly large contractions (negative strains) when charged up to 4.65 V, where intergranular crack formation and phase transformation were detected on the LCO particles via SEM and XRD, respectively. Overall, the study bridges complicated structural deformations with in situ analysis of mechanical degradations in LCO cathodes charged at higher voltages. The correlation is vital to understanding instability mechanisms in transition metal oxides at high voltages for alkali metal ion batteries.
higher state-of-charge↗
Total Dose Testing of a CMOS Charged Particle Spectrometer
A first-generation CMOS Charged Particle Spectrometer chip [1] was designed at JPL for flight on the STRV-2 spacecraft. These devices will collect electron and proton spectra in low Earth orbit as part of an experiment to demonstrate Active Pixel Sensor (APS) technology in space. This paper presents the results of total dose testing on these chips and, where possible, attempts to extend the results to other Active Pixel Sensors.
CMOS↗
Avalanche photodiode and an optical receiver having the same
Examples described herein relate to an avalanche photodiode (APD) and an optical receiver including the APD. The APD may include a substrate and a photon absorption region disposed on the substrate. The substrate may include a charge carrier acceleration region under the photon absorption region; a charge region adjacent to the charge carrier acceleration region; and a charge carrier multiplication region adjacent to the charge region. The charge carrier acceleration region, the charge region, and the charge carrier multiplication region are laterally formed in the substrate. When a biasing voltage is applied to the optoelectronic device, photon-generated free charge carriers may be generated in the photon absorption region and are diffused into the charge carrier acceleration region. The charge carrier acceleration region is configured to accelerate the photon-generated free charge carriers prior to the photon-generated free charge carriers entering into the charge region and undergoing impact ionization in the charge carrier multiplication region.
Yuan, Yuan↗
Development of 3-Phase CCD Timing Generator
Charge-Coupled Devices (CCDs) are used in a wide range of commercial, scientific, and defense applications. They are primarily utilized for imaging and spectroscopic functions. Compact, cost-effective technology to miniaturize the auxiliary electronics required to operate the CCD is highly desirable. Because of the importance of reducing size and weight in defense and space applications, emphasis must be placed on the reduction in size. The purpose of this project is to minimize the CCD timing generator electronics for 3-phase CCDs by replacing conventional ICs with a single programmable IC. This timing generator will give the user the ability to vary the number of horizontal and vertical pixels and to choose between integration and readout modes. This, in turn, will reduce the size and weight of CCD focal plane assemblies as a whole.
Bennett, Kory L.↗
Metal–Carbodithioate-Based 3D Semiconducting Metal–Organic Framework: Porous Optoelectronic Material for Energy Conversion
Solar energy conversion requires the working compositions to generate photoinduced charges with high potential and the ability to deliver charges to the catalytic sites and/or external electrode. These two properties are typically at odds with each other and call for new molecular materials with sufficient conjugation to improve charge conductivity but not as much conjugation as to overly compromise the optical band gap. In this work, we developed a semiconducting metal-organic framework (MOF) prepared explicitly through metal-carbodithioate"(-CS 2 ) n M" linkage chemistry, entailing augmented metal-linker electronic communication. The stronger ligand field and higher covalent character of metal-carbodithioate linkages-when combined with spirofluorene-derived organic struts and nickel-(II) ion-based nodes-provided a stable, semiconducting 3D-porous MOF, Spiro-CS 2 Ni. This MOF lacks long-range ordering and is defined by a flexible structure with non-aggregated building units, as suggested by reverse Monte Carlo simulations of the pair distribution function obtained from total scattering experiments. The solvent-removed "closed pore"material recorded a Brunauer-Emmett-Teller area of similar to 400m 2 /g, where the "open pore" form possesses90 wt % solvent-accessible porosity. Electrochemical measurements suggest that Spiro-CS 2 Ni possesses a band gap of 1.57 eV(sigma = 10 -7 S/cm at -1.3 V bias potential),which can be further improved by manipulating the d-electron configuration through an axial coordination (ligand/substrate), the latter of which indicates usefulness as an electrocatalyst and/or a photoelectrocatalyst(upon substrate binding). Transient-absorption spectroscopy reveals a long-lived photo-generated charge-transfer state (τ CR = 6.5 mu s) capable of chemical transformation under a biased voltage. Spiro-CS 2 Ni can endure a compelling range of pH(1-12 for weeks) and hours of electrochemical and photoelectrochemical conditions in the presence of water and organic acids. We believe this work provides crucial design principles for low-density, porous,light-energy-conversion materials.
36 MATERIALS SCIENCE↗
Interaction of a solar array with an ion thruster due to the charge-exchange plasma
The generation of a charge exchange plasma by a thruster, the transport of this plasma to the solar array, and the interaction of the solar array with the plasma after it arrives are all described. The generation of this plasma is described accurately from thruster geometry and operating conditions. The transport of the charge exchange plasma was studied experimentally with a 15 cm thruster. A model was developed for simple thruster array configurations. A variety of experiments were surveyed for the interaction of the plasma at the solar array.
Kaufman, H. R.↗
Methods and algorithms of cyclic coulometry
Systems, devices, and methods of diagnosing an electrochemical cell using cyclic coulometry are discussed. An exemplary battery diagnostic system comprises a current generator to generate symmetric charge current and discharge current to excite an electrochemical cell, and a cyclic coulometer to evaluate performance of the electrochemical cell. The cyclic coulometer can adjust at least one of a charge time for applying the charge current, or a discharge time for applying the discharge current, to keep a monitored cell voltage toward a specific setpoint. The adjustment of charge or discharge time can be achieved by changing a current switch timing for reversing current from a first to a second current direction. The cyclic coulometer measures one or more electrical parameters during the charge or discharge cycle, and generates a performance metric using the measured electrical parameters.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Effect of Palladium‐Tetrakis(Triphenylphosphine) Catalyst Traces on Charge Recombination and Extraction in Non‐Fullerene‐based Organic Solar Cells
Abstract The effect of the cross‐coupling catalyst tetrakis(triphenylphosphine)palladium(0) (Pd(PPh 3 ) 4 ) on the performance of a model organic bulk‐heterojunction solar cell composed of a blend of poly([2,6′‐4,8‐di(5‐ethylhexylthienyl)benzo[1,2‐b;3,3‐b]dithiophene]{3‐fluoro‐2[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl}) (PTB7‐Th) donor and 3,9‐bis(2‐methylene‐((3‐(1,1‐dicyanomethylene)‐6,7‐difluoro)‐indanone))‐5,5,11,11‐tetrakis(4‐hexylphenyl)‐dithieno[2,3‐d:2′,3′‐d′]‐s‐indaceno[1,2‐b:5,6‐b′]dithiophene (IOTIC‐4F) non‐fullerene acceptor is investigated. The effect of intentional addition of different amounts of Pd(PPh 3 ) 4 on morphology, free charge carrier generation, non‐geminate bulk trap‐ and surface trap‐assisted recombination as well as bimolecular recombination and charge extraction is quantified. This work shows that free charge carrier generation is affected significantly, while the impact of Pd(PPh 3 ) 4 on non‐geminate recombination processes is limited because the catalyst does not facilitate efficient trap‐assisted recombination. The studied system shows substantial robustness towards the addition of Pd(PPh 3 ) 4 in small amounts.
Schopp, Nora↗
Photoinjector Generation of High-Charge Magnetized Beams for Electron-Cooling Applications
The recently announced Electron-Ion Collider (EIC), to be built at Brookhaven National Laboratory, will collide high-energy ion-beams and electron beams to pursue nuclear physics research on quark-gluon plasma's. The facility performances (luminosity) would be improved if the ion-beam emittance degradation is mitigated via a phase-space-cooling technique. One potential cooling method uses a bright electron beam to cool the ion beams. The cooling rate for this electron-cooling method depends on the transverse emittance of the cooling electron beam and could benefit from using a beam with significant canonical angular momentum dubbed as a magnetized beam. This research focuses on simulation and experimental generation and characterization of high charge magnetized electron beams with parameters comparable to those required for electron cooling at an electron-ion collider. The experiment uses the 50-MeV photo-injector available at the Fermilab Accelerator Science and Technology (FAST) Facility. The measurements are benchmarked against simulations.
43 PARTICLE ACCELERATORS↗
Combination of searches for pair-produced leptoquarks at s = 13 TeV with the ATLAS detector
A statistical combination of various searches for pair-produced leptoquarks is presented, using the full LHC Run 2 (2015–2018) data set of 139 fb -1 collected with the ATLAS detector from proton–proton collisions at a centre-of-mass energy of $\sqrt{s}$ = 13 TeV. All possible decays of the leptoquarks into quarks of the third generation and charged or neutral leptons of any generation are investigated. Since no significant deviations from the Standard Model expectation are observed in any of the individual analyses, combined exclusion limits are set on the production cross-sections for scalar and vector leptoquarks. The resulting lower bounds on leptoquark masses exceed those from the individual analyses by up to 100 GeV, depending on the signal hypothesis.
72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
Operational optimization for multi-functional charging station with electric and hydrogen-powered vehicles
The rapid adoption of electric vehicles (EVs) and hydrogen fuel cell vehicles (HFCVs), combined with global efforts to reduce carbon emissions, has accelerated the development of EV charging and hydrogen refueling stations. In response to this demand, this paper introduces the concept of Multi-Functional Charging Station (MFCS) that integrates power generation, EV charging, battery swapping, and hydrogen refueling. A comprehensive operational model is developed for the MFCS that couples electricity and hydrogen conversion and storage technologies to enhance infrastructure utilization and improve overall system efficiency. The model also considers multiple revenue streams, including participation in energy and ancillary markets. To validate the effectiveness of the proposed model and evaluate its performance, a series of numerical experiments are conducted with different charger numbers, different electricity purchase limits, and different charger allocations. Numerical results demonstrate that shared charger configurations can lead to 8.11 % improvement in operational profit by improving resource utilization and reducing the number of depleted batteries at the end of operations compared to allocated charger setups. By varying the number of chargers, sensitivity analysis identifies diminishing marginal returns beyond about 45 chargers, suggesting it as an optimal sizing point under current settings. The integration of electricity and hydrogen conversion is also explored under scenarios with limited external electricity purchases. In conclusion, these findings indicate that optimizing charger allocation and energy management can significantly enhance station productivity and profitability, ultimately supporting the broader adoption of electrified and hydrogen-based transportation solutions.
Charging station↗
Caldera_Grid
Caldera Grid is part of Caldera software platform, a suite of collective, open-source tools that was developed to improve the state of the art in modeling the impacts of Electric Vehicle (EV) charging on the grid. Caldera Grid is a co-simulation framework implemented using Hierarchical Engine for Large scale Infrastructure Co-Simulation (HELICS). The framework facilitates the co-simulation of EV charging and Smart Charge Management (SCM) strategies in Caldera Infrastructure Charge Model (ICM) with distribution level grid models in OpenDSS. Vehicle energy needs and charge session requirements generated using Caldera Charge Decision Module (CDM) are fed in as input to Caldera Grid. The EV charging models in Caldera ICM simulates both the uncontrolled charging loads as well as loads modified by the SCM strategies to develop distributed load profiles for each grid node hosting an Electric Vehicle Supply Equipment (EVSE) – also known as chargers. These loads were simulated in OpenDSS alongside existing distribution feeder loads. Each of these models are co-simulated in a HELICS federate. The HELICS co-simulation framework facilitates communication and synchronization between the federates. By co-simulating EV loads and distribution feeder loads, Caldera Grid can assess the potential grid impacts of EV charging on distribution feeders under various grid conditions. A control strategy federate is implemented with an interface where control strategies based on feedback from EV charging status and grid conditions can be developed and implemented. The platform can also support multiple control strategies in a single co-simulation.
Sundarrajan, ManojKumar Cebol↗
Response of NiMH Cells to Burp Charging
Performance cycling and calorimetric analysis of nickel metal hydride (NNH) calls have revealed that reverse pulse ("burp") charging improves performance over other charging techniques. Burp charging periodically applies a short-duration, high-rate discharge pulse followed by short rest during an otherwise galvanostatic charge as shown in Fig. 1. Results show improved charge input and output, lower heat generation during charge, lower charge overvoltage, and no loss of cycle life [I]. The burp charge method has been improved over the years purely by trial and error. Several hypotheses have been put forward (see articles cited in (1) to explain why burp charging improves performance For example, it has been suggested that the discharge pulses dislodge gas bubbles that would otherwise mask the active elect-ode surfaces. However, no evidence was found in the literature to support this or other hypotheses. Overall, a better understanding of the phenomenon is needed to help guide further improvements in the burp-charging method, and this is the objective of our investigation.
Darcy, Eric C.↗
Materials Characterization at Utah State University: Facilities and Knowledge-base of Electronic Properties of Materials Applicable to Spacecraft Charging
In an effort to improve the reliability and versatility of spacecraft charging models designed to assist spacecraft designers in accommodating and mitigating the harmful effects of charging on spacecraft, the NASA Space Environments and Effects (SEE) Program has funded development of facilities at Utah State University for the measurement of the electronic properties of both conducting and insulating spacecraft materials. We present here an overview of our instrumentation and capabilities, which are particularly well suited to study electron emission as related to spacecraft charging. These measurements include electron-induced secondary and backscattered yields, spectra, and angular resolved measurements as a function of incident energy, species and angle, plus investigations of ion-induced electron yields, photoelectron yields, sample charging and dielectric breakdown. Extensive surface science characterization capabilities are also available to fully characterize the samples in situ. Our measurements for a wide array of conducting and insulating spacecraft materials have been incorporated into the SEE Charge Collector Knowledge-base as a Database of Electronic Properties of Materials Applicable to Spacecraft Charging. This Database provides an extensive compilation of electronic properties, together with parameterization of these properties in a format that can be easily used with existing spacecraft charging engineering tools and with next generation plasma, charging, and radiation models. Tabulated properties in the Database include: electron-induced secondary electron yield, backscattered yield and emitted electron spectra; He, Ar and Xe ion-induced electron yields and emitted electron spectra; photoyield and solar emittance spectra; and materials characterization including reflectivity, dielectric constant, resistivity, arcing, optical microscopy images, scanning electron micrographs, scanning tunneling microscopy images, and Auger electron spectra. Further details of the instrumentation used for insulator measurements and representative measurements of insulating spacecraft materials are provided in other Spacecraft Charging Conference presentations. The NASA Space Environments and Effects Program, the Air Force Office of Scientific Research, the Boeing Corporation, NASA Graduate Research Fellowships, and the NASA Rocky Mountain Space Grant Consortium have provided support.
Dennison, J. R.↗
Study of Velocity and Materials on Tribocharging of Polymer Powders for Powder Coating Applications
Electrostatic powder deposition is widely used in a plethora of industrial-applications ranging from the pharmaceutical and food.industries, to farm equipment and automotive applications. The disadvantages of this technique are possible back corona (pin-like formations) onset and the Faraday penetration limitation (when the powder does not penetrate in some recessed areas). A possible solution to overcome these problems is to use tribochargers to electrostatically charge the powder. Tribocharging, or contact charging while two materials are in contact, is related to the work function difference between the contacting materials and generates bipolarly charged particles. The generation of an ion-free powder cloud by tribocharging with high bipolar charge and an overall charge density of almost zero, provides a better coverage of the recessed areas. In this study, acrylic and epoxy powders were fluidized and charged by passing through stainless steel, copper, aluminum, and polycarbonate static mixers, respectively. The particle velocity was varied to determine its effect on the net charge-to-mass ratio (QIM) acquired by the powders. In general, the Q/M increases rapidly when the velocity was increased from 1.5 to 2.5 m/s, remaining almost constant for higher velocities. Charge separation experiments showed bipolar charging for all chargers.
Biris, Alex S.↗
Atomic-Scale Structure and Catalysis on Positively Charged Bimetallic Sites for Generation of H 2
In this paper, we report that a cationic bimetallic site consisting of one Pd and three Zn atoms (Pd 1 Zn 3 ) supported on ZnO (Pd 1 Zn 3 /ZnO) exhibits an extraordinarily high catalytic activity for the generation of H 2 through methanol partial oxidation (MPO) that is 2–3 orders of magnitude higher than that of a metallic Pd–Zn site on Pd–Zn nanoalloy (Pd–Zn/ZnO). Computational studies uncovered that the positively charged Pd atom of the subnanometer Pd 1 Zn 3 bimetallic site largely decreases the activation barrier for dehydrogenation of methanol as compared to a metallic Pd atom of Pd–Zn alloy, thus switching the rate-determining step of MPO from methanol dehydrogenation over a Pd–Zn alloy with high barrier to the O 2 dissociation step on a cationic Pd 1 Zn 3 site with a low barrier, which is supported by our kinetics studies. The significantly higher catalytic activity and selectivity for H 2 production over a cationic bimetallic site suggest a new approach to design bimetallic catalysts.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗