Search NASA⌕ Search

SEARCH · Search NASA

Results for “clean water”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Development of a Testbed for Pipeline Flushing - 20425

Pipelines which carry high-level waste within the DOE complex should be properly flushed in the cases where stationary or moving beds of solid sediment occur, or lines are prone to hydrogen gas buildup. Present guidelines establish a minimum for the amount of water (flush volume) and flush velocity values used for post-transfer flushing operations to achieve satisfactory cleaning of pipelines. However, further studies are needed to find optimal operating velocity modes/values in order to minimizing the flush volume and consequent downstream waste. These efforts are significantly helpful to DOE waste remediation sites by preserving tank storage, preventing additional waste processing, and minimizing dilution and changes in waste chemistry. An experimental test loop was recently developed for study of non-Newtonian slurry flushing at the Florida International University (FIU). This loop was designed to create sediment beds of various materials and bed heights and investigate parameters that effect the efficiency of flushing operations. The objective is to find flush velocity values/modes which lead to satisfactory cleaning of transport lines with a minimum amount of water usage. A 165 ft experimental test loop made of 3-inch carbon steel pipes was constructed and used in initial testing campaigns. This pipe loop was equipped with real-time monitoring instruments to record variation of pressure, density, mass flow rate, and temperature during testing. Post-flush in-situ no-flow evaluations were performed using ultrasonic, endoscopy, and visual inspection. Additional post-flush evaluations were conducted using filtration and density monitoring of residuals within a designated circulations loop. These provisions enable comparison of pipeline cleanness before the start and after termination of flushing operations for efficiency evaluation. This paper presents efforts associated with flushing of kaolin-water mixtures at different concentrations and with various flush volume and flush velocity values/modes. In initial testing, efforts focused on creating repeatable sediment beds inside the pipeline in both fully-flooded (no pre-flush drainage) and gravity-drained (pre-flush drained) systems. Bed characterization (i.e., measurement of sediment height and solids concentration) was conducted to ensure about consistency of initial conditions between tests. Preliminary results for flushing study of 10% vol. kaolin-water mixtures starting from a fully-flooded initial condition showed that flushing with 1-line volume (65 gallons) could remove up to 72 percent of solids from the pipeline. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

E-Area Low-Level Waste Facility Inadvertent Human Intruder Limits and Doses in Support of the PA2022

This report documents the inadvertent human intruder (IHI) analysis for the E-Area Low-Level Waste Facility (ELLWF) at the Savannah River Site (SRS), near Aiken, South Carolina. This analysis supports the revised ELLWF Performance Assessment (PA), complying with the Department of Energy standard for operation of low-level waste disposal facilities (USDOE, 2017). The ELLWF is an operating waste disposal facility and is scheduled to continue accepting waste to 2065. One task of the revised PA is to establish waste inventory limits for the various disposal units at ELLWF. This is done by modeling future contaminant release and transport through applicable pathways to human receptors, comparing predicted doses per disposed curie with applicable performance measures, to obtain inventory limits which will assure that doses to receptors do not exceed performance measures. This report documents results of modeling future doses to one class of receptor, the inadvertent human intruder. It is assumed that after site closure, public knowledge of the site is lost, and IHIs will engage in activities on the ELLWF that will disrupt the closure cap, causing dose to the IHI. Following USDOE (2017), six different stylized exposure scenarios are considered, simulating activities by an IHI which could result in a radiological dose. The six scenarios are: • Acute – Basement Construction: IHI constructs a basement and encounters waste during excavation which is inadvertently mixed with clean soil and diluted. • Acute – Well Drilling: IHI drills a water well through waste and is exposed to drill cuttings mixed with clean soil that are brought to the surface. • Acute – Discovery: IHI begins constructing a basement but stops when encountering the riprap in the final closure cap and is exposed to photon radiation from unexcavated material residing in the undisturbed waste zone. • Chronic – Agriculture: Resident IHI is exposed to waste that was excavated for basement construction and mixed with native soil in the intruder’s vegetable garden. • Chronic – Post-Drilling: Resident IHI is exposed to waste from drill cuttings mixed with native soil and scattered in the garden area. • Chronic – Residential: Resident IHI is exposed to external radiation while in home located above waste with shielding provided by the concrete basement floor and any soil or engineered material remaining between the basement and waste. Dose calculations are performed using the SRNL Dose Toolkit (Aleman, 2023), following the approach of Smith et al (2019). Calculations are performed separately for 27 of the 33 disposal units (DUs) at ELLWF and are radionuclide specific. The results of the IHI analysis include: • Dose Factors: mrem per disposed curie (acute) and mrem/yr per disposed curie (chronic) for each parent radionuclide, for each DU. • Inventory Limits: in curies, for each parent radionuclide, for each DU. • Estimated Dose to IHI: mrem (acute) and mrem/yr (chronic), for each DU, given its projected closure inventory without inventory biases applied. Most DU-specific IHI inventory limits are in the range of 10 3 to 10 7 curies per nuclide. The lowest inventory limits are associated with gamma-emitters such as Sn-126, Ra-226, Th-232, and Cm-248. Radionuclides with short half-lives such as Pu-241, and nuclides which are pure beta emitters or which decay by electron capture, such as Ni-59 and Ni-63, have the highest limits. For the 27 evaluated DUs, predicted IHI doses are shown in Table ES-1. The maximum acute dose is 1.18 mrem, at ST23, much less than the DOE performance measure of 500 mrem (USDOE, 2017). The highest chronic dose is 37.2 mrem/yr at ST02, below the DOE performance measure of 100 mrem/yr. Also shown are estimated inventory sums of fractions (SOFs) at closure in 2065, for groundwater (GW) and IHI pathways. For each DU, the inventory is constrained by the GW pathway. For most DUs, the IHI SOFs are approximately 1000 times lower than the GW SOF values, and the IHI pathway does not drive risk for any disposal unit.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Cutting-edge methods for amplifying the oxygen evolution reaction during seawater electrolysis: a brief synopsis

Electrochemical water splitting has been considered a clean and continual way for hydrogen (H 2 ) production. Direct seawater electrolysis is a potentially attractive technology due to the ample access to seawater and scarce freshwater resources in some regions. However, the presence of impurities (e.g., Cl - , Mg 2+ ) and the resulting corrosion and side reactions, such as the chloride oxidation reaction (ClOR), makes seawater electrocatalysis more challenging than that of fresh or alkaline water due to competition with the oxygen evolution reaction (OER) at the anode. Consequently, much effort has been devoted to developing approaches to enhance OER performance and suppress the ClOR. In this minireview, we summarize three general strategies for enhancing OER activity and selectivity in seawater electrolysis based on three different concepts: (1) the sole development of robust and high-performance OER catalysts in pure seawater electrolytes, (2) the introduction of additives to seawater electrolytes (e.g., alkalis and/or salts without chloride) to enhance the potential equilibrium gap between the ClOR and OER in combination with regular highly active OER catalysts, and (3) a combination of approaches (1) and (2). Finally, the current challenges and potential opportunities for green H 2 production from seawater electrolysis are briefly presented.

08 HYDROGEN↗
DOE OSTI2024

Self-Cleaning Highly Porous TiO 2 Coating Designed by Swelling-Assisted Sequential Infiltration Synthesis (SIS) of a Block Copolymer Template

Photocatalytic self-cleaning coatings with a high surface area are important for a wide range of applications, including optical coatings, solar panels, mirrors, etc. Here, we designed a highly porous TiO 2 coating with photoinduced self-cleaning characteristics and very high hydrophilicity. This was achieved using the swelling-assisted sequential infiltration synthesis (SIS) of a block copolymer (BCP) template, which was followed by polymer removal via oxidative thermal annealing. The quartz crystal microbalance (QCM) was employed to optimize the infiltration process by estimating the mass of material infiltrated into the polymer template as a function of the number of SIS cycles. This adopted swelling-assisted SIS approach resulted in a smooth uniform TiO 2 film with an interconnected network of pores. The synthesized film exhibited good crystallinity in the anatase phase. The resulting nanoporous TiO 2 coatings were tested for their functional characteristics. Exposure to UV irradiation for 1 h induced an improvement in the hydrophilicity of coatings with wetting angle reducing to unmeasurable values upon contact with water droplets. Furthermore, their self-cleaning characteristics were tested by measuring the photocatalytic degradation of methylene blue (MB). The synthesized porous TiO 2 nanostructures displayed promising photocatalytic activity, demonstrating the degradation of approximately 92% of MB after 180 min under ultraviolet (UV) light irradiation. Thus, the level of performance was comparable to the photoactivity of commercial anatase TiO 2 nanoparticles of the same quantity. Our results highlight a new robust approach for designing hydrophilic self-cleaning coatings with controlled porosity and composition.

36 MATERIALS SCIENCE↗
DOE OSTI2024

"Soiling, Cleaning, and Abrasion: The Results of the Five-Year Photovoltaic Glass Coating Field Study" [Slides]

External contamination ("soiling") of the incident surface is a major limiting factor for solar technologies. A 5-year field glass coupon study was conducted to better understand external contamination and its effects; compare cleaning methods and the use of preventative coatings; and explore the abrasion resulting from cleaning to advise on accelerated abrasion testing. Test sites included the cities of Dubai (UAE), Kuwait City (Kuwait), Mesa (AZ), Mumbai (India), and Sacramento (CA). Through the 5-year cumulative study, dry brush, water spray, and wet sponge and squeegee cleaning methods were compared to no cleaning. Optical microscopy was used to obtain images, including representative color images, grayscale images for object analysis, and oblique images for coating integrity assessment. A thresholding protocol was developed to analyze and distinguish specimens using the ImageJ software. Optical performance was quantified using a spectrophotometer, including comprehensive optical characterization (transmittance, reflectance, and absorptance in addition to forward- and back-scattering). Atomic force microscopy was used to verify the abrasion damage morphology, including the width and depth of surface scratches. Analysis of the results included correlation of optical performance and particle area coverage, rank order (by coating or location), and the acceleration factor for abrasion damage. The efficacy of external cleaning was more readily distinguished from the effectiveness of antisoiling coatings. The acceleration factor for dry brush cleaning of a porous silica coating was found to be on the order of unity.

14 SOLAR ENERGY↗
DOE OSTI2020

Ultra-clean and smoky marine boundary layers frequently occur in the same season over the southeast Atlantic

We study 41 d with daily median surface accumulation mode aerosol particle concentrations below 50 cm -3 (ultra-clean conditions) observed at Ascension Island (ASI; 7.9° S, 14.4° W) between June 2016 and October 2017 as part of the Layered Atlantic Smoke Interactions with Clouds (LASIC) campaign. Interestingly, these days occur during a period of great relevance for aerosol–cloud–radiation interactions, the southeast Atlantic (SEATL)biomass-burning season (approximately June–October). That means that these critical months can feature both the highest surface aerosol numbers, from smoke intrusion into the marine boundary layer, as well as the lowest. While carbon monoxide and refractory black carbon concentrations on ultra-clean days do not approach those on days with heavy smoke, they also frequently exceed background concentrations calculated in the non-burning season from December 2016 to April 2017. This is evidence that even what become ultra-clean boundary layers can make contact with and entrain from an overlying SEATL smoke layer before undergoing a process of rapid aerosol removal. Because many ultra-clean and polluted boundary layers observed at Ascension Island during the biomass burning season follow similar isobaric back trajectories, the variability in this entrainment is likely more closely tied to the variability in the overlying smoke rather than large-scale horizontal circulation through the boundary layer. Since exceptionally low accumulation mode aerosol numbers at ASI do not necessarily indicate the relative lack of other trace pollutants, this suggests the importance of regional variations in what constitutes an “ultra-clean” marine boundary layer. Finally, surface drizzle rates, frequencies and accumulation – as well as retrievals of liquid water path– all consistently tend toward higher values on ultra-clean days. This implicates enhanced coalescence scavenging in low clouds as the key driver of ultra-clean events in the southeast Atlantic marine boundary layer. These enhancements occur against and are likely mediated by the backdrop of a seasonal increase in daily mean cloud fraction and daily median liquid water path over ASI, peaking in September and October in both LASIC years. Therefore the seasonality in ultra-clean day occurrence seems directly linked to the seasonality in SEATL cloud properties. These results highlight the importance of two-way aerosol–cloud interactions in the region.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Heterostructured Au–Ir Catalysts for Enhanced Oxygen Evolution Reaction

Electrochemical water splitting operated under acidic conditions provides a clean approach to generate hydrogen fuels. Currently, the sluggish kinetics of oxygen evolution reaction (OER) at the anode is a bottleneck limiting the acidic water splitting. Here, we report that the OER activity of Ir, one of the most commonly used OER catalysts, can be boosted by forming phase boundaries with Au. Mixed Au and Ir catalysts were synthesized on carbon paper electrodes, which underwent structural evolution under the OER environment to form an Au-Ir interface-rich structure. Compared with Ir catalyst, which requires an overpotential of ~393 mV to achieve a current density of 10 mA/cm 2 in 0.1 M HClO 4 electrolyte, the evolved Au-Ir catalyst shows a lower overpotential at ~351 mV. X-ray photoelectronic spectrum (XPS) study, in conjunction with electrochemical analysis on the surface-site-normalized activity, reveals that the improved OER performance is due to the presence of Au/Ir interfaces in the catalysts. In addition to Ir, the strategy of accelerating OER via Au/Ir interfaces has been further applied to IrCo, IrNi, and IrCu alloy catalysts. Here, with the broad applicability of the strategy demonstrated, this study opens a new route to design OER catalysts for efficient acidic water splitting.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Modeling the aqueous interface of amorphous TiO 2 using deep potential molecular dynamics

Amorphous titanium dioxide (a-TiO 2 ) is widely used as a coating material in applications such as electrochemistry and self-cleaning surfaces where its interface with water has a central role. However, little is known about the structures of the a-TiO 2 surface and aqueous interface, particularly at the microscopic level. In this work, we construct a model of the a-TiO 2 surface via a cut-melt-and-quench procedure based on molecular dynamics simulations with deep neural network potentials (DPs) trained on density functional theory data. After interfacing the a-TiO 2 surface with water, we investigate the structure and dynamics of the resulting system using a combination of DP-based molecular dynamics (DPMD) and ab initio molecular dynamics (AIMD) simulations. Both AIMD and DPMD simulations reveal that the distribution of water on the a-TiO 2 surface lacks distinct layers normally found at the aqueous interface of crystalline TiO 2 , leading to an ~10 times faster diffusion of water at the interface. Bridging hydroxyls (Ti 2 –O b H) resulting from water dissociation decay several times more slowly than terminal hydroxyls (Ti–O w H) due to fast Ti–O w H 2 → Ti–O w H proton exchange events. These results provide a basis for a detailed understanding of the properties of a-TiO 2 in electrochemical environments. Moreover, the procedure of generating the a-TiO 2 -interface employed here is generally applicable to studying the aqueous interfaces of amorphous metal oxides.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Reflection Optical Imaging to Study Oxygen Evolution Reactions

Discovery of high-efficiency water-splitting catalysts is critical for clean hydrogen fuel generation. Quantitative and reliable chemical imaging methods can play a crucial role in providing critical catalyst efficiency information for materials development and screening. Here, we developed a reflection optical imaging method to map the performance of transition metal oxide catalysts for oxygen evolution reaction (OER). The generated high concentration of oxygen in the electrolyte will decrease the refractive index of the solutions near the electrode and change the reflectivity of optical images. We successfully imaged and measured the OER on cobalt oxide, and the localized current density and overpotential distribution maps have been extracted. The oxidation and reduction of cobalt oxide can be imaged with our reflection optical imaging method as well. These maps showed that the catalytic activities are quite different at different locations, and some regions showed much higher activities. This is due to the non-uniformity created by the catalyst synthesis process and demonstrates the importance of using the optical imaging method to map the localized catalytic efficiency. In addition, the NiFe alloy’s OER catalytic activities have been studied as well. The proposed reflection optical imaging method could find many applications in catalyst activity measurement and screening.

Electrochemistry↗
DOE OSTI2023

Dataset Repository for Investigating Suicide Risk Using Social and Environmental Determinants of Health

Suicide is frequently modeled as a function of genetics and environment, where the latter refers to factors other than direct biological consequences, such as air quality, financial level, social connectivity, transportation and food access, and homelessness status. According to the World Health Organization, clean air, a stable climate, adequate water, sanitation and hygiene, safe chemical use, radiation protection, healthy and safe workplaces, sound agricultural practices, health-supportive cities and built environments, and a preserved natural environment are all prerequisites for good health. Understanding the relationships between these determinants and mental health outcomes requires standardized data that can be included in healthcare programs and health outcome models. There is a wealth of publicly available data on social and environmental factors provided by various US organizations that can benefit the design of health care systems and public health interventions, as well as improve our comprehension of factors that impact health. Such information would not only help improve the understanding of individual and community risk but also identify new risk factors that have not previously been therapeutically targeted, especially in terms of their impact on mental health. However, curating and standardizing such datasets is challenging because they are often recorded at numerous geographical and temporal resolutions and with varying spatial and temporal granularities. To address this challenge, we launched an endeavor in conjunction with the Veterans Health Administration to collect publicly available socioeconomic and environmental determinants of health statistics in the US. In this manuscript, we describe a social and environmental determinants of health (SEDH) datasets repository, data curation documentation, and a pipeline framework for data generation; This effort started in 2020, when we began constructing a scalable pipeline to automate the download, extraction, preparation, analysis, and production of datasets. These datasets have been made available to the VHA and may be shared upon agreement with collaborating organizations.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

FY 2021 Site Sustainability Plan

The U.S. Department of Energy's (DOE's) National Renewable Energy Laboratory (NREL) Fiscal Year 2021 Site Sustainability Plan details the laboratory's current performance status relative federal mandates and goals pertaining to water, waste, fleet, and energy management; clean and renewable energy; green buildings; acquisition and procurement; measures, funding, and training; electronic stewardship; and organizational resilience. It also provides a road map for future site planning and development that support NREL's commitment to business operations that 1) demonstrate the incorporation of clean energy practices and 2) promote the development of a sustainable and resilient campus while growing greater technological capabilities to advance the national renewable energy marketplace.

ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Los Angeles 100% Clean Energy Equity Strategies

The National Renewable Energy Laboratory and Los Angeles Department of Water and Power set out to identify strategies to improve equity in LA's transition to 100% clean energy. Through social science research, NREL summarized underserved community member challenges and solutions from listening sessions and community-based organizations. NREL modeled future scenarios for solar, transportation electrification, rates, building technologies, and the distribution grid to identify strategies that improved community-prioritized equity metrics. Findings provide specific strategies relevant for LA and elsewhere to improve equity and affordability in achieving 100% clean energy.

100% clean energy↗
DOE OSTI2020

Opportunities for Using the Industrial Assessment Center Database for Industrial Water Use Analysis

The manufacturing sector accounted for approximately 5–6% of total U.S. water use in 2015. Of that amount, 75–80% is self supplied withdrawal from surface-water and groundwater sources and the remainder is from public water supplies. Although manufacturing facilities commonly locate in water-scarce areas, water scarcity still poses a great risk to the manufacturing sector. Reliable water is necessary for any facility that relies on it for process and comfort cooling, cleaning, employee use, and steam generation. One of these barriers to water efficiency is the lack of reliable data on overall U.S. industrial water use—how it is used and the quantities required for each sector. If a facility cannot be easily compared with a facility of similar size and sector, knowing if it is effectively using water conservation best practices is difficult. One potential source of industrial water use data is the U.S. Department of Energy (DOE)–sponsored Industrial Assessment Centers (IACs). IACs are university-based organizations that provide free audits to small- and medium-sized manufacturing facilities to identify productivity improvement and waste and energy reduction opportunities. The IACs also maintain a database of all the audits conducted, which currently holds more than 19,267 assessments and 145,000 recommendations (as of July 24, 2020). This database also contains energy utility (electricity, natural gas, and other fuels) and water utility data, making it a potential data source for industrial water use. This report attempts to create regression models to predict a small- or medium-sized industrial facility’s annual water use or cost based on its industrial subsector and several possible relevant variables. Using data collected by IAC assessments, models for several industrial subsectors were generated via stepwise regression techniques to determine which variables (annual sales, number of employees, facility/plant area, annual production hours, and a water stress metric) are relevant.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Synthetic dioxygenase reactivity by pairing electrochemical oxygen reduction and water oxidation

The reactivity of molecular oxygen is crucial to clean energy technologies and green chemical synthesis, but kinetic barriers complicate both applications. In synthesis, dioxygen should be able to undergo oxygen atom transfer to two organic molecules with perfect atom economy, but such reactivity is rare. Monooxygenase enzymes commonly reductively activate dioxygen by sacrificing one of the oxygen atoms to generate a more reactive oxidant. Here, we used a manganese-tetraphenylporphyrin catalyst to pair electrochemical oxygen reduction and water oxidation, generating a reactive manganese-oxo at both electrodes. This process supports dioxygen atom transfer to two thioether substrate molecules, generating two equivalents of sulfoxide with a single equivalent of dioxygen. This net dioxygenase reactivity consumes no electrons but uses electrochemical energy to overcome kinetic barriers.

Science & Technology - Other Topics↗
DOE OSTI2023

First Experience with Liquid Nitrogen Cleaning

Field emission caused by microscopic particulate contamination is a limiting factor for the performance of superconducting RF (SRF) cavities. In an SRF based accelerator, particulates may be transported over the surface of an operational SRF cavity, becoming field emitters and consequentially degrading the performance of the SRF cavity. The most commonly used method for removing particulates from cavity surfaces is high-pressure ultra-pure water rinsing. We are developing a novel high-pressure liquid nitrogen cleaning technique that may possibly enable superior cleaning power and particulate removal from cavities in a cryomodule without taking apart the cryomodule components. This technique provides cleaning mechanisms beyond what are accessible by its high-pressure water rinsing counterpart and leaves no residues on the cleaned surface.

Ruber, R.J.M.Y.↗