Search NASA⌕ Search

SEARCH · Search NASA

Results for “climbing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Rapid near-optimal aerospace plane trajectory generation and guidance

Problems associated with onboard trajectory optimization, propulsion system cycle selection, and the synthesis of guidance laws are addressed for ascent to low earth orbit of an airbreathing, single-stage-to-orbit vehicle. A multicycle propulsion system is assumed that incorporates turbojet, ramjet, scramjet, and rocket engines. An energy state approximation is applied to a singularly perturbed, four-state dynamic model for flight of a point mass over a spherical nonrotating earth. An algorithm is then derived for generating both the fuel-optimal climb profile and the guidance commands required to follow that profile. In particular, analytic switching conditions are derived that, under appropriate assumptions, efficiently govern optimal transition from one propulsion cycle to another. The algorithm proves to be computationally efficient and suitable for real-time implementation. The paper concludes with the presentation of representative numerical results that illustrate the nature of the fuel-optimal climb paths and the tracking performance of the guidance algorithm.

Corban, J. E.↗
NASA NTRS1992

Stress versus temperature dependence of activation energies for creep

The activation energy for creep at low stresses and elevated temperatures is associated with lattice diffusion, where the rate controlling mechanism for deformation is dislocation climb. At higher stresses and intermediate temperatures, the rate controlling mechanism changes from dislocation climb to obstacle-controlled dislocation glide. Along with this change in deformation mechanism occurs a change in the activation energy. When the rate controlling mechanism for deformation is obstacle-controlled dislocation glide, it is shown that a temperature-dependent Gibbs free energy does better than a stress-dependent Gibbs free energy in correlating steady-state creep data for both copper and LiF-22mol percent CaF2 hypereutectic salt.

Freed, A. D.↗
NASA NTRS1991

Flow and fracture behavior of NiAl in relation to the brittle-to-ductile transition temperature

NiAl has only three independent slip systems operating at low and intermediate temperatures whereas five independent deformation mechanisms are required to satisfy the von Mises criterion for general plasticity in polycrystalline materials. Yet, it is generally recognized that polycrystalline NiAl can be deformed extensively in compression at room temperature and that limited tensile ductility can be obtained in extruded materials. In order to determine whether these results are in conflict with the von Mises criterion, tension and compression tests were conducted on powder-extruded, binary NiAl between 300 and 1300 K. The results indicate that below the brittle-to-ductile transition temperature (BDTT) the failure mechanism in NiAl involves the initiation and propagation of cracks at the grain boundaries which is consistent with the von Mises analysis. Furthermore, evaluation of the flow behavior of NiAl indicates that the transition from brittle to ductile behavior with increasing temperature coincides with the onset of recovery mechanisms such as dislocation climb. The increase in ductility above the BDTT is therefore attributed to the climb of the 001 line type dislocations which in combination with dislocation glide enable grain boundary compatibility to be maintained at the higher temperatures.

Noebe, R. D.↗
NASA NTRS1992

Optimal recovery from microburst wind shear

The flight path of a twin-jet transport aircraft is optimized in a microburst encounter during approach to landing. The objective is to execute an escape maneuver that maintains safe ground clearance and an adequate stall margin during the climb-out portion of the trajectory. A cost function penalizing rate of climb deviations from a nominal value and rate of elevator deflection produces qualitatively good results in a variety of microburst encounters. The optimal maneuver is a gradual pitch-up that ceases near the core of the microburst, followed by a slight reduction in pitch attitude in the tailwind area of the microburst. A minimum airspeed constraint in the optimization prevents excessive airspeed loss in very severe microbursts. The aircraft equations of motion include short-period dynamics, so that the optimization solves directly for the control surface deflections required to achieve the optimal flight paths.

Mulgund, Sandeep S.↗
NASA NTRS1992

Mechanical Design Engineering Enabler Project wheel and wheel drives

Our group was assigned the responsibility of designing the wheel and wheel drive system for a proof-of-concept model of the lunar-based ENABLER. ENABLER is a multi-purpose, six wheeled vehicle designed to lift and transport heavy objects associated with the construction of a lunar base. The resulting design was based on the performance criteria of the ENABLER. The drive system was designed to enable the vehicle to achieve a speed of 7 mph on a level surface, climb a 30 percent grade, and surpass a one meter high object and one meter wide crevice. The wheel assemblies were designed to support the entire weight of the vehicle on two wheels. The wheels were designed to serve as the main component of the vehicle's suspension and will provide suitable traction for lunar-type surfaces. The expected performance of the drive system for the ENABLER was influenced by many mechanical factors. The expected top speed on a level sandy surface is 4 mph instead of the desired 7 mph. This is due to a lack of necessary power at the wheels. The lack of power resulted from dimension considerations that allowed only an eight horsepower engine and also from mechanical inefficiencies of the hydraulic system. However, the vehicle will be able to climb a 30 percent grade, surpass a one meter high object and one meter wide crevice. The wheel assemblies will be able to support the entire weight of the vehicle on two wheels. The wheels will also provide adequate suspension for the vehicle and sufficient traction for lunar-type surfaces.

Nutt, Richard E.↗
NASA NTRS1992

Near-optimal energy transitions for energy-state trajectories of hypersonic aircraft

A problem of the instantaneous energy transition that occurs in energy-state approximation is considered. The transitions are modeled as a sequence of two load-factor bounded paths (either climb-dive or dive-climb). The boundary-layer equations associated with the energy-state dynamic model are analyzed to determine the precise location of the transition.

Ardema, M. D.↗
NASA NTRS1920

Airplane Performance as Influenced by the Use of a Supercharged Engine

The question of the influence of a supercharged engine on airplane performance is treated here in a first approximation, but one that gives an exact idea of the advantage of supercharging. Considered here is an airplane that climbs first with an ordinary engine, not supercharged, and afterwards climbs with a supercharged engine. The aim is to find the difference of the ceilings reached in the two cases. In the case of our figure, the ceiling from 25,000 feet is increased to 37,000 feet, the supercharging maintaining the power only up to 20,000 feet. This makes, in comparison with an engine without supercharging, an increase of about 50 percent.

ENGINES, SUPERCHARGED - PERFORMANCE↗
NASA NTRS1920

Recent Efforts and Experiments in the Construction of Aviation Engines

It became evident during World War I that ever-increasing demands were being placed on the mean power of aircraft engines as a result of the increased on board equipment and the demands of aerial combat. The need was for increased climbing efficiency and climbing speed. The response to these demands has been in terms of lightweight construction and the adaptation of the aircraft engine to the requirements of its use. Discussed here are specific efforts to increase flying efficiency, such as reduction of the number of revolutions of the propeller from 1400 to about 900 r.p.m. through the use of a reduction gear, increasing piston velocity, locating two crankshafts in one gear box, and using the two-cycle stroke. Also discussed are improvements in the transformation of fuel energy into engine power, the raising of compression ratios, the use of super-compression with carburetors constructed for high altitudes, the use of turbo-compressors, rotary engines, and the use of variable pitch propellers.

SCHWAGER↗
NASA NTRS1927

A warning concerning the take-off with heavy load

A successful take-off can be made with an airplane so heavily loaded that it cannot climb to a height greater than the span of its wings. The explanation is that the power required to maintain level flight at an altitude of the order of the wing span may be as much as 50 per cent greater than that necessary when the airplane is just clear of the ground. The failure of heavily loaded airplanes to continue climbing at the rate attained immediately after the actual take-off is a grave hazard and has resulted in great risk or catastrophe in three notable cases which are cited.

Reid, Elliott G↗
NASA NTRS1928

The Effect on Performance of a Cutaway Center Section

The assumption is made that a skeleton or cutaway center section is desirable for forward vision and to determine the effect of such mutilation upon performance the following work was done. The airplane used was a Vought VE-7 and in addition to the cutaway center section a system of end plates or fins was installed. Various conditions and combinations were investigated in level flight and in climb. It is found that the greatest difference in the conditions investigated was a drop of 12.5 per cent in a 10-minute climb while the effect upon level speeds was negligible.

Carroll, Thomas↗
NASA NTRS1930

Comparative Performance Obtained with XF7C-1 Airplane Using Several Different Engine Cowlings

Discussed here are problems with the use of cowlings with radial air cooled engines. An XF7C-1 airplane, equipped with service cowling and with narrow ring, wide ring, and exhaust collector ring cowlings over the service cowling, was used. For these four cowling conditions, the rate of climb and high speed performance were determined, the cylinder conditions were measured, and pictures to show visibility were taken. The level flight performance obtained with an engine speed of 1900 r.p.m. for the service type, the narrow ring, the wide ring, and the exhaust collector ring was 144.4, 146.6, 152.8, and 155 mph, respectively. The rate of climb was practically the same for each type tested. The visibility was not materially impaired by the use of the wide or the narrow cowlings. With the narrow ring and exhaust collector ring cowlings there was an increase in cylinder temperature. However, this increase was not enough to affect the performance of the engine. The use of an exhaust collector ring incorporated into the cowling is practical where the problem of visibility does not enter.

Schey, Oscar W↗
NASA NTRS1939

Wind-tunnel investigation of an N.A.C.A. 23012 airfoil with two arrangements of a wide-chord slotted flap

An investigation has been made in the N.A.C.A. 7- by 10-foot wind tunnel of a large-chord N.A.C.A. 23012 airfoil with several arrangements of a 40-percent-chord slotted flap to determine the section aerodynamic characteristics of the airfoil as affected by slot shape, flap location, and flap deflection. The flap positions for maximum lift, the polar for arrangements considered favorable for take-off and climb, and the complete section aerodynamic characteristics for selected optimum arrangements were determined. A discussion is given of the relative merits of the various arrangements. A comparison is made of slotted flaps of different chords on the N.A.C.A. 23012 airfoil. The best 40-percent-chord slotted flap is only slightly superior to the 25-percent-chord slotted flap from considerations of maximum lift coefficient and low drag for take-off and initial climb.

Harris, Thomas A↗
NASA NTRS1947

Charts Showing Relations Among Primary Aerodynamic Variables for Helicopter-performance Estimation

In order to facilitate solutions of the general problem of helicopter selection, the aerodynamic performance of rotors is presented in the form of charts showing relations between primary design and performance variables. By the use of conventional helicopter theory, certain variables are plotted and other variables are considered fixed. Charts constructed in such a manner show typical results, trends, and limits of helicopter performance. Performance conditions considered include hovering, horizontal flight, climb, and ceiling. Special problems discussed include vertical climb and the use of rotor-speed-reduction gears for hovering.

THEORIES - HELICOPTERS↗
NASA NTRS1951

Tests of Two-Blade Propellers in the Langley 8-Foot High-Speed Tunnel to Determine the Effect on Propeller Performance of a Modification of Inboard Pitch Distribution

Tests of two propellers having two blades and differing only in the inboard pitch distribution were made in the Langley 8-foot highspeed tunnel to determine the effect of inboard pitch distribution on propeller performance. propeller was designed for operation in the reduced velocity region ahead of an NACA cowling; the inboard pitch distribution of the modified propeller was increased for operation at or near free-stream velocities, such as would be obtained in a pusher installation. conditions covering climb, cruise, and high-speed operation. Wake surveys were taken behind the propellers in order to determine the distribution of thrust along the blades and to aid in the analysis of the results. Test results showed that the modified propeller was about 2.5 percent less efficient for a typical climb condition at all altitudes, 2 percent more efficient for one cruise condition, and 5 percent more efficient for high-speed operation. speed condition, the modified propeller showed a 6-percent loss in efficiency due to compressibility; whereas the original propeller showed an 11-percent efficiency loss due to compressiblity. The lower compressibility loss for the modified propeller resulted from the fact that the inboard sections of this propeller could operate at increased thrust loading after compressibility losses had occurred at the outboard sections.

PROPELLERS - PERFORMANCE↗
NASA NTRS1928

Preliminary Flight Tests of the N.A.C.A. Roots Type Aircraft Engine Supercharger

An investigation of the suitability of the N.A.C.A. Roots type aircraft engine supercharger to flight-operating conditions, as determined the effects of the use of the supercharger upon engine operation and airplane performance, is described in this report. Attention was concentrated on the operation of the engine-supercharger unit and on the improvement of climbing ability; some information concerning high speeds at altitude was obtained. The supercharger was found to be satisfactory under flight-operating conditions. Although two failures occurred during the tests, the causes of both were minor and have been eliminated. Careful examination of the engines revealed no detrimental effects which could be attributed to supercharging. Marked improvements in climbing ability and high speeds at altitude were effected. It was also found that the load which could be carried to a given moderate or high altitude in a fixed time was considerably augmented. A slight sacrifice of low-altitude performance was necessitated, however, by the use of a fixed-pitch propeller. From a consideration of the very satisfactory flight performance of the Roots supercharger and of its inherent advantages, it is concluded that this type is particularly attractive for use in certain classes of commercial airplanes and in a number of military types.

Gardiner, Arthur W↗
NASA NTRS1929

A Preliminary Investigation of Supercharging an Air-Cooled Engine in Flight

This report presents the results of preliminary tests made on the effects of supercharging an air-cooled engine under airplane flight conditions. Service training airplanes were used in the investigation equipped with production types of Wright J engines. A N.A.C.A. Roots type supercharger was driven from the rear of the engine. In addition to measuring those quantities that would enable the determination of the climb performance, measurements were made of the cylinder-head temperatures and the carburetor pressures and temperatures. The supercharging equipment was not removed from the airplane when making flights without supercharging, but a by-pass valve, which controlled the amount of supercharging by returning to the atmosphere the surplus air delivered by the supercharger, was left full open. With the supercharger so geared that ground-level pressure could be maintained to 18,500 feet, it was found that the absolute ceiling was increased from 19,400 to 32,600 feet, that the time to climb to 16,00 feet was decreased from 32 to 16 minutes, and that this amount of supercharging apparently did not injure the engine. (author)

Ware, Marsden↗
NASA NTRS1931

Comparative Flight Performance with an NACA Roots Supercharger and a Turbocentrifugal Supercharger

This report presents the comparative flight results of a roots supercharger and a turbocentrifugal supercharger. The tests were conducted using a modified DH-4M2 airplane. The rate of climb and the high speed in level flight of the airplane were obtained for each supercharger from sea level to the ceiling. The unsupercharged performance with each supercharger mounted in place was also determined. The results of these tests show that the ceiling and rate of climb obtained were nearly the same for each supercharger, but that the high speed obtained with the turbocentrifugal was better than that obtained with the roots. The high-speed performance at 21,000 feet was 122 and 142 miles per hour for the roots and turbocentrifugal, respectively.

Schey, Oscar W↗