Search NASA⌕ Search

SEARCH · Search NASA

Results for “concept normalization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Supercritical airfoil drag reduction by passive shock wave/boundary layer control in the Mach number range .75 to .90

Airfoils operating in the transonic region are subject to large increases in drag due to shock wave/boundary layer interactions. The concept of passive shock wave/boundary layer control seeks drag reduction by placing a thin cavity with a porous top surface at the airfoil chordwise position where a shock wave would normally occur. The higher pressure behind the shock wave circulates flow through the cavity to the lower pressure ahead of the shock wave. The effects from this circulation prevent boundary layer separation and reduce entropy increases through the shock wave. In this investigation this concept is studied at a freestream Mach number range of .75 and .90. The Mach number distributions over the model, the wake impact pressure surveys used to determine profile drag and schlieren photographs for 2.8 percent porosity and solid airfoil cases are presented and compared. Results indicate that the profile drag coefficient can be reduced by as much as 40 percent through the use of this passive drag control system.

Nagamatsu, H. T.↗
NASA NTRS1990

A flight expert system for on-board fault monitoring and diagnosis

An architecture for a flight expert system (FLES) to assist pilots in monitoring, diagnosing, and recovering from inflight faults is described. A prototype was implemented and an attempt was made to automate the knowledge acquisition process by employing a learning by being told methodology. The scope of acquired knowledge ranges from domain knowledge, including the information about objects and their relationships, to the procedural knowledge associated with the functionality of the mechanisms. AKAS (automatic knowledge acquisition system) is the constructed prototype for demonstration proof of concept, in which the expert directly interfaces with the knowledge acquisition system to ultimately construct the knowledge base for the particular application. The expert talks directly to the system using a natural language restricted only by the extent of the definitions in an analyzer dictionary, i.e., the interface understands a subset of concepts related to a given domain. In this case, the domain is the electrical system of the Boeing 737. Efforts were made to define and employ heuristics as well as algorithmic rules to conceptualize data produced by normal and faulty jet engine behavior examples. These rules were employed in developing the machine learning system (MLS). The input to MLS is examples which contain data of normal and faulty engine behavior and which are obtained from an engine simulation program. MLS first transforms the data into discrete selectors. Partial descriptions formed by those selectors are then generalized or specialized to generate concept descriptions about faults. The concepts are represented in the form of characteristic and discriminant descriptions, which are stored in the knowledge base and are employed to diagnose faults. MLS was successfully tested on jet engine examples.

Ali, Moonis↗
NASA NTRS1979

Elementary analytic models of climate. 1: The mean global heat balance

Climate models based on global radiative equilibrium are normally so complicated that they require extensive computer codes to provide adequate accuracy. However, by simply modifying the concept of a gray atmosphere, a reasonably correct mean global temperature is obtained. This elementary model is then used to estimate the effects of changes in the abundances of minor infrared absorbers and changes in the solar constant or earth albedo. When applied to a Budyko-Sellers zonally averaged model, the quasi-gray model could give a physical basis for the latitude dependence of outgoing radiation and of opacity due to H2O vapor content. The latter effect constitutes an important positive feedback on surface temperature.

Chamberlain, J. W.↗
NASA NTRS1982

LANDSAT-D ground segment operations plan, revision A

The basic concept for the utilization of LANDSAT ground processing resources is described. Only the steady state activities that support normal ground processing are addressed. This ground segment operations plan covers all processing of the multispectral scanner and the processing of thematic mapper through data acquisition and payload correction data generation for the LANDSAT 4 mission. The capabilities embedded in the hardware and software elements are presented from an operations viewpoint. The personnel assignments associated with each functional process and the mechanisms available for controlling the overall data flow are identified.

Evans, B.↗
NASA NTRS1982

Comparison of three-dimensional turbulent boundary-layer calculations with experiment

A numerical simulation is carried out of the incompressible three-dimensional turbulent boundary-layer experiments of van den Berg and Elsenaar (1972), Dechow (1977), and Muller (1982). The simulation is effected by integrating the boundary-layer equations together with an algebraic eddy-viscosity turbulence model. With this computational method, the downstream portion of the flow treated by van den Berg and Elsenaar, where the crossflow is large, cannot be predicted. It is believed that this flow is significantly influenced by elliptic flow-field effects. Even though Dechow's experiment also indicated departures from the boundary-layer concept, the calculations made here agree reasonably well with the mean-flow development up to separation. The normal pressure gradients in Muller's experiment are found to be negligible in regions with large skewing, making it possible to test turbulence models using the boundary-layer equations. The simulation of this flow compares favorably with the experimental data throughout the flow field.

Muller, U. R.↗
NASA NTRS1990

Superfluid helium on-orbit resupply

The requirements for superfluid helium (SFHe) resupply were investigated, and the results were used to develop a conceptual design for a superfluid helium tanker (SFHT) which is designed to meet a 50-mission requirement. The SFHT design uses a conventional dewar approach with multiple vapor cooled shields, and a porous-plug phase separator for on-orbit temperature control. An open loop refrigeration approach is used for ground conversion of normal He to SFHe, allowing near-total fill of the supply tank. Design diagrams of the SFHT concept and of various SFHT subsystems are presented.

Eberhardt, Ralph N.↗
NASA NTRS1993

Imaging the magnetosphere in the extreme ultraviolet

A final report on research on magnetosphere imaging in the extreme ultraviolet is presented. The objectives of the research contract can be summarized in three related items: (1) investigate the feasibility of the EUV imaging concept by using Lockheed in-situ ion measurement data; (2) investigate the technical resources required to make scientific interpretations of such EUV images by end-to-end simulations of the imaging concept; and (3) construct and test the key element for EUV magnetosphere imaging, the multilayer mirror with normal-incidence reflectance designed for the selected solar resonance line.

Chiu, Y. T.↗
NASA NTRS2008

Testing the Efficacy of Synthetic Vision during Non-Normal Operations as an Enabling Technology for Equivalent Visual Operations

Synthetic Vision (SV) may serve as a revolutionary crew/vehicle interface enabling technology to meet the challenges of the Next Generation Air Transportation System Equivalent Visual Operations (EVO) concept that is, the ability to achieve or even improve on the safety of Visual Flight Rules (VFR) operations, maintain the operational tempos of VFR, and potentially retain VFR procedures independent of actual weather and visibility conditions. One significant challenge lies in the definition of required equipage on the aircraft and on the airport to enable the EVO concept objective. An experiment was conducted to evaluate the effects of the presence or absence of SV, the location (head-up or head-down) of this information during an instrument approach, and the type of airport lighting information on landing minima. Another key element of the testing entailed investigating the pilot s awareness and reaction to non-normal events (i.e., failure conditions) that were unexpectedly introduced into the experiment. These non-normals are critical determinants in the underlying safety of all-weather operations. This paper presents the experimental results specific to pilot response to non-normal events using head-up and head-down synthetic vision displays.

Kramer, Lynda J.↗
NASA NTRSDate not supplied

Linear Polarizer Design for Application in the Far-Ultraviolet Spectral Range

New mission concepts that are under consideration by NASA call for the design and implementation of Far Ultraviolet (FUV) polarizer technologies that have not been developed yet. A team that includes members from the NASA Goddard Space Flight Center (GSFC), Arizona State University (ASU), and Woodruff Consulting, worked on the design and development of a polarizer design that produce very high extinction ratios in the FUV spectral range (100-200 nm). This polarizer consists of reflecting light through a series of mirrors from a combination of two silicon carbide (SiC) and two lithium fluoride (LiF) crystals positioned at angles of incidence (relative to surface normal) close to the average LiF Brewster’s angle in the FUV. The output is a highly linearly polarized beam. This polarizer concept was fabricated and tested in the existing McPherson 225 Vacuum Ultraviolet (VUV) spectrometer located in the Optics Branch at NASA-GSFC. Initial testing using a MgF2 crystal at the Brewster’s angle as an analyzer has shown that this design can produce state-of-the-art extinction ratios at the Hydrogen Lyman-Alpha (Ly-α) wavelength of 121.6 nm, and that the measured extinction ratio of the two crossed polarizers, ≈114, is mostly limited by the MgF2 analyzer. A polarizer with such a performance at this wavelength has never been reported and it signifies a breakthrough in FUV polarization technology. The levels of effectiveness paired with the polarizer’s compact design allows for a new polarizer capability that would one day be implemented in a future FUV spectropolarimetry space mission.

Far Ultraviolet (FUV)↗
NASA NTRS1984

Capture of liquid hydrogen boiloff with metal hydride absorbers

A procedure which uses metal hydrides to capture some of this low pressure (,1 psig) hydrogen for subsequent reliquefaction is described. Of the five normally occurring sources of boil-off vapor the stream associated with the off-loading of liquid tankers during dewar refill was identified as the most cost effective and readily recoverable. The design, fabrication and testing of a proof-of-concept capture device, operating at a rate that is commensurate with the evolution of vapor by the target stream, is described. Liberation of the captured hydrogen gas at pressure .15 psig at normal temperatures (typical liquefier compressor suction pressure) are also demonstrated. A payback time of less than three years is projected.

Rosso, M. J.↗
NASA NTRS2003

Use of a Prototype Airborne Separation Assurance System for Resolving Near-Term Conflicts During Autonomous Aircraft Operations

NASA is currently investigating a new concept of operations for the National Airspace System, designed to improve capacity while maintaining or improving current levels of safety. This concept, known as Distributed Air/Ground Traffic Management (DAGTM), allows appropriately equipped autonomous aircraft to maneuver freely for flight optimization while resolving conflicts with other traffic and staying out of special use airspace and hazardous weather. In order to perform these tasks, pilots use prototype conflict detection, prevention, and resolution tools, collectively known as an Airborne Separation Assurance System (ASAS). While ASAS would normally allow pilots to resolve conflicts before they become hazardous, evaluation of system performance in sudden, near-term conflicts is needed in order to determine concept feasibility. An experiment was conducted in NASA Langley's Air Traffic Operations Lab to evaluate the prototype ASAS for enabling pilots to resolve near-term conflicts and examine possible operational effects associated with the use of lower separation minimums. Sixteen commercial airline pilots flew a total of 32 traffic scenarios that required them to use prototype ASAS tools to resolve close range pop-up conflicts. Required separation standards were set at either 3 or 5 NM lateral spacing, with 1000 ft vertical separation being used for both cases. Reducing the lateral separation from 5 to 3 NM did not appear to increase operational risk, as indicated by the proximity to the intruder aircraft. Pilots performed better when they followed tactical guidance cues provided by ASAS than when they didn't follow the guidance. In an effort to improve compliance rate, ASAS design changes are currently under consideration. Further studies will of evaluate these design changes and consider integration issues between ASAS and existing Airborne Collision Avoidance Systems (ACAS).

Barhydt, Richard↗
NASA NTRS1975

Fail-safe system for activity cooled supersonic and hypersonic aircraft

A fail-safe-system concept was studied as an alternative to a redundant active cooling system for supersonic and hypersonic aircraft which use the heat sink of liquid-hydrogen fuel for cooling the aircraft structure. This concept consists of an abort maneuver by the aircraft and a passive thermal protection system (TPS) for the aircraft skin. The abort manuever provides a low-heat-load descent from normal cruise speed to a lower speed at which cooling is unnecessary, and the passive TPS allows the aircraft skin to absorb the abort heat load without exceeding critical skin temperature. On the basis of results obtained, it appears that this fail-safe-system concept warrants further consideration, inasmuch as a fail-safe system could possibly replace a redundant active cooling system with no increase in weight and would offer other potential advantages.

Jones, R. A.↗
NASA NTRS2012

An Efficient Analysis Methodology for Fluted-Core Composite Structures

The primary loading condition in launch-vehicle barrel sections is axial compression, and it is therefore important to understand the compression behavior of any structures, structural concepts, and materials considered in launch-vehicle designs. This understanding will necessarily come from a combination of test and analysis. However, certain potentially beneficial structures and structural concepts do not lend themselves to commonly used simplified analysis methods, and therefore innovative analysis methodologies must be developed if these structures and structural concepts are to be considered. This paper discusses such an analysis technique for the fluted-core sandwich composite structural concept. The presented technique is based on commercially available finite-element codes, and uses shell elements to capture behavior that would normally require solid elements to capture the detailed mechanical response of the structure. The shell thicknesses and offsets using this analysis technique are parameterized, and the parameters are adjusted through a heuristic procedure until this model matches the mechanical behavior of a more detailed shell-and-solid model. Additionally, the detailed shell-and-solid model can be strategically placed in a larger, global shell-only model to capture important local behavior. Comparisons between shell-only models, experiments, and more detailed shell-and-solid models show excellent agreement. The discussed analysis methodology, though only discussed in the context of fluted-core composites, is widely applicable to other concepts.

Oremont, Leonard↗
NASA NTRS2001

Concept of Operations for Commercial and Business Aircraft Synthetic Vision Systems

A concept of operations (CONOPS) for the Commercial and Business (CaB) aircraft synthetic vision systems (SVS) is described. The CaB SVS is expected to provide increased safety and operational benefits in normal and low visibility conditions. Providing operational benefits will promote SVS implementation in the Net, improve aviation safety, and assist in meeting the national aviation safety goal. SVS will enhance safety and enable consistent gate-to-gate aircraft operations in normal and low visibility conditions. The goal for developing SVS is to support operational minima as low as Category 3b in a variety of environments. For departure and ground operations, the SVS goal is to enable operations with a runway visual range of 300 feet. The system is an integrated display concept that provides a virtual visual environment. The SVS virtual visual environment is composed of three components: an enhanced intuitive view of the flight environment, hazard and obstacle defection and display, and precision navigation guidance. The virtual visual environment will support enhanced operations procedures during all phases of flight - ground operations, departure, en route, and arrival. The applications selected for emphasis in this document include low visibility departures and arrivals including parallel runway operations, and low visibility airport surface operations. These particular applications were selected because of significant potential benefits afforded by SVS.

Williams Daniel M.↗
NASA NTRS1969

High-power microwave power divider concept

Variable power divider keeps microwave transmitter at full power. This preserves the bandwidth and modulation characteristics and proportions any amount of the full power from the normal antenna into a dissipative load.

Kolbly, R. B.↗
NASA NTRS1973

Atomic oxygen transport in the thermosphere.

The photodissociation of oxygen in the lower thermosphere is evaluated to obtain its global average value and the hemispheric imbalance. The observed concentrations of atomic oxygen do not reflect this imbalance in production due to the effect of seasonal wind patterns redistributing the atomic oxygen. The wind system necessary to compensate for the imbalance in solar thermal input into the lower thermosphere is found to transport an amount of atomic oxygen sufficient to compensate for the hemispheric imbalance in production. Ionospheric data indicate a winter enhancement in atomic oxygen concentration; to produce this, a higher degree of oxygen dissociation than that normally accepted (i.e., higher than an atomic to molecular oxygen ratio of unity at 120 km) is needed. The concept that the concentrations of atomic oxygen observed over the winter polar region are maintained by transport from lower latitudes requires that eddy diffusion coefficients derived from vertical transport at low latitudes (ignoring horizontal transport) be reduced by about 25%.

Johnson, F. S.↗
NASA NTRS1974

A dual frequency radar for ocean roughness sampling

A microwave technique for determining the roughness (rms wave height) of a randomly varying air-water interface has been developed theoretically, verified with laboratory wavetank studies and is currently being implemented for ocean surface measurements in a series of applications flight experiments. These aircraft observations will be near the Chesapeake Light Tower and will include a range of altitudes and sea conditions. The measurement concept involves cross-correlating the envelope fluctuations on two received carriers that are monochromatic when transmitted in a normal direction to the interface and are observed in a backscatter direction after reflection by the large number of randomly distributed specular points on the surface. The measured correlation coefficient (normalized covariance) as a function of carrier frequency separation will depend on the surface roughness, specifically the probability density function of the specular point height. Details of the flight system are discussed, and preliminary flight results are presented.

Weissman, D. E.↗
NASA NTRS1979

Further developments in simple total energy sensors

A simple total energy probe concept using principles of laminar flow around a cylinder and pressure distribution is reviewed and flow fields around cylinders normal to and inclined to the flow are described. A variety of bent-up probe configurations were tested to explore variations in geometry. Test results are presented on the effects of sensor length, hole location, and angle of sweep. Comparisons are made with other probe tests reported in the literature. Damping restrictors and their use in filtering gusts are summarized. Flow field effects, indicating the variables involved for different mounting locations on aircraft, are discussed.

Nicks, O. W.↗