Search NASA⌕ Search

SEARCH · Search NASA

Results for “conductive films”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Emissivity measurements in thin metallized membrane reflectors used for microwave radiometer sensors

This paper is concerned with electromagnetic losses in metallized films used for inflatable reflectors. An inflatable membrane is made of tough elastic material such as Kapton, and it is not electromagnetically reflective by design. A film of conducting metal is added to the membrane to enhance its reflective properties. Since the impetus for use of inflatables for spacecraft is the light weight and compact packaging, it is important that the metal film be as thin as possible. However, if the material is not conductive or thick enough, the radiation due to the emissivity of the reflector could be a significant part of the radiation gathered by the radiometer. The emissivity would be of little consequence to a radar or solar collector; but for a radiometer whose signal is composed of thermal radiation, this contribution could be severe. Bulk properties of the metal film cannot be used to predict its loss. For this reason, a program of analysis and measurement was undertaken to determine the emissivities of a number of candidate metallized film reflectors. This paper describes the three types of measurements which were performed on the metallized thin films: (1) a network analyzer system with an L-band waveguide; (2) an S-band radiometer; and (3) a network analyzer system with a C-band antenna free-space transmission system.

Schroeder, Lyle C.↗
NASA NTRS1980

Coating of plasma polymerized film

Plasma polymerized thin film coating and the use of other coatings is suggested for passivation film, thin film used for conducting light, and solid body lubrication film of dielectrics of ultra insulators for electrical conduction, electron accessories, etc. The special features of flow discharge development and the polymerized film growth mechanism are discussed.

Morita, S.↗
NASA NTRS1972

Comparison of MX-857 versus MX-641 chemistries for type 2485 film

Tests were conducted to evaluate Kodak MX-857 and MX-641 chemistry systems for use with film Type 2485 to be used in the dim light experiments on Apollo 16. The test program objectives were to: (1) retain a minimum ASA speed of at least 4000; (2) maintain a base-plus-fog level of 0.21 density units or less; and (3) minimize the granularity but do not exceed the granularity level of the Apollo 15 imagery. Test results on the Versamat processor indicate that the use of MX-857 chemistry is preferred over MX-641 chemistry in satisfying the stated test objectives.

Bourque, P. F.↗
NASA NTRS1985

Dielectric properties of 'diamondlike' carbon prepared by RF plasma deposition

Metal-carbon-metal structures were fabricated using either gold or aluminum evaporated electrodes and RF plasma (methane) deposited 'diamondlike' carbon films. Alternating-current conductance and capacitance versus voltage and frequency (10 Hz to 13 MHz) data were taken to determine the dielectric properties of these films. Conductance versus frequency data fit a generalized power law, consistent with both dc and hopping conduction components. The capacitance versus frequency data are well matched to the conductance versus frequency data, as predicted by a Kramers-Kronig analysis. The dielectric loss tangent is nearly constant at 0.5 to 1.0 percent over the frequency range from 1 to 100 kHz. The dc resistivity is above 10 to the 13th ohm cm, and the dc breakdown strength is above 8 x 10 to the 6th V/cm is properly prepared samples.

Lamb, J. D.↗
DOE OSTI2020

3D Ion-Conducting, Scalable, and Mechanically Reinforced Ceramic Film for High Voltage Solid-State Batteries

Concerning the safety aspects of Li+ ion batteries, an epoxy-reinforced thin ceramic film (ERTCF) is prepared by firing and sintering a slurry-casted composite powder film. The ERTCF is composed of Li + ion conduction channels and is made of high amounts of sintered ceramic Li 1+ x Ti 2-x Al x (PO 4 ) 3 (LATP) and epoxy polymer with enhanced mechanical properties for solid-state batteries. The two- and three-dimensional characterizations are conducted not only for showing continuous Li+ ion channels thorough LATP ceramic channels with over 10-4 S cm-1 of ionic conductivity but also to investigate small amounts of epoxy polymer with enhanced mechanical properties. Solid-state Li + ion cells are fabricated using the ERTCF and they show initial charge–discharge capacities of 139/133 mAh g -1 . Furthermore, the scope of the ERTCF is expanded to high-voltage (>8 V) solid-state Li + ion batteries through a bipolar stacked cell design. Hence, it is expected that the present investigation will significantly contribute in the preparation of the next generation reinforced thin ceramic film electrolytes for high-voltage solid-state batteries.

25 ENERGY STORAGE↗
NASA NTRS1985

Evaluation of capillary reinforced composites

Anti-icing of the inlet of jet engines is generally performed with high pressure heated air that is directed forward from the compressor through a series of pipes to various manifolds located near the structures to be anti-iced. From these manifolds, the air is directed to all flowpath surfaces that may be susceptible to ice formation. There the anti-icing function may be performed by either heat conduction or film heating. Unfortunately, the prospect of utilizing lighweight, high strength composites for inlet structures of jet engines has been frustrated by the low transverse thermal conductivity of such materials. It was the objective of this program to develop an advanced materials and design concept for anti-icing composite structures. The concept that was evaluated used capillary glass tubes embedded on the surface of a composite structure with heated air ducted through the tubes. An analytical computer program was developed to predict the anti-icing performance of such tubes and a test program was conducted to demonstrate actual performance of this system. Test data and analytical code results were in excellent agreement. Both indicate feasibility of using capillary tubes for surface heating as a means for composite engine structures to combat ice accumulation.

Cahill, J. E.↗
DOE OSTI2025

Understanding Fracture Aperture and Permeability Evolution due to Carbonate Mineralization Utilizing 3D Printing

Caprock formations are a crucial part of subsurface-engineered systems. Composed largely of shale, caprocks act as natural barriers that prevent the upward migration of fluids, thereby ensuring the containment of stored substances in subsurface formations. Fractures in these formations are potential leakage pathways for stored fluids. Mineral precipitation reactions in these fractures, particularly calcite, can significantly restrict the fluid permeability, reducing leakage potential. However, predictive capabilities of mineral precipitation in fractures and associated permeability evolution are limited due to a lack of fundamental understanding of such reactions in natural samples, complicated by mineral heterogeneity and the complexity of the fracture structure. In this study, 3D-printed fracture samples are used to understand the impact of carbonate mineralization on fracture aperture and permeability evolution. Samples were printed using a digital light processing (DLP) 3D printer and commercial liquid resin. Calcite precipitation was first tested on printed 2D films before conducting plug flow column experiments aimed to understand fracture permeability changes due to mineral precipitation. Contact angle measurement and Fourier transform infrared (FTIR) spectroscopy on printed 2D films show evidence of a substantial amount of surface energy for calcite nucleation and precipitation. Surface topography analysis of printed fractured surfaces reveals comparable values, highlighting the high replicability of the printed samples. During the column experiments, the permeability reduces exponentially due to a decrease in fracture aperture. Reductions in fracture aperture estimated from effluent concentration and 3D X-ray computed tomography (CT) show comparable results. Moreover, 3D X-ray CT images suggest the impact of local flow velocities on precipitation. The insights gained from this research contribute to a deeper understanding of the permeability evolution due to carbonate mineralization in caprock formations.

3D printing↗
DOE OSTI2022

Transition Metal Dissolution Mechanisms and Impacts on Electronic Conductivity in Composite LiNi 0.5 Mn 1.5 O 4 Cathode Films

The high-voltage LiNi 0.5 Mn 1.5 O 4 (LNMO) spinel cathode material offers high energy density storage capabilities without the use of costly Co that is prevalent in other Li-ion battery chemistries (e.g., LiNi x Mn y Co z O 2 (NMC)). Unfortunately, LNMO-containing batteries suffer from poor cycling performance because of the intrinsically coupled processes of electrolyte oxidation and transition metal dissolution that occurs at high voltage. In this work, we use operando electron paramagnetic resonance (EPR) and nuclear magnetic resonance (NMR) spectroscopies to demonstrate that transition metal dissolution in LNMO is tightly coupled to HF formation (and thus, electrolyte oxidation reactions as detected with operando and in situ solution NMR), indicative of an acid-driven disproportionation reaction that occurs during delithiation (i.e., battery charging). Leveraging the temporal resolution (s-min) of magnetic resonance, we find that the LNMO particles accelerate the rate of LiPF 6 decomposition and subsequent Mn 2+ dissolution, possibly due to the acidic nature of terminal Mn-OH groups. X-ray photoemission electron microscopy (XPEEM) provides surface-sensitive and localized X-ray absorption spectroscopy (XAS) measurements, in addition to X-ray photoelectron spectroscopy (XPS), that indicate disproportionation is enabled by surface reconstruction upon charging, which leads to surface Mn 3+ sites on the LNMO particle surface that can disproportionate into Mn 2+ (dissolved) and Mn 4+ (s) . During discharge of the battery, we observe high quantities of metal fluorides (in particular, MnF 2 ) in the cathode electrolyte interphase (CEI) on LNMO as well as the conductive carbon additives in the composite. Electronic conductivity measurements indicate that the MnF 2 decreases film conductivity by threefold compared to LiF, suggesting that this CEI component may impede both the ionic and electronic properties of the cathode. Ultimately, to prevent transition metal dissolution and the associated side reactions in spinel-type cathodes (particularly those that operate at high voltages like LNMO), the use of electrolytes that offer improved anodic stability and prevent acid byproducts will likely be necessary.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Combinatorial investigation of the Mn–Ge–N chemical system containing ternary nitrides Mn 3 GeN and MnGeN 2

By changing nitrogen chemical potential during synthesis of Mn–Ge–N ternary nitrides, both wurtzite MnGeN 2 and antiperovskite Mn 3 GeN ternary phases are prepared. Antiperovskite films are optically opaque and conductive, while wurtzite films with Mn/(Mn + Ge) ≤ 0.5 transmit light above ~ 2 eV. Alloys of Mn 3 GeN with Si and Al are also investigated. Mn 3 (Ge 1−x Al x )N alloys with 0.07 ≤ x ≤ 0.16 exhibit a cubic (rather than tetragonal) structure. Mn 3 (Ge 1−x Si x )N with x ≤ 0.05 maintains the tetragonal structure but becomes cubic when x > 0.05. This study shows that care must be taken in the synthesis of Mn–Ge–N and similar nitrides, especially when materials are integrated into devices not amenable to structural and chemical probing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Low temperature atomic layer deposition of PbO 2 for electrochemical applications

A low temperature atomic layer deposition (ALD) process for PbO 2 was developed using bis(1-dimethylamino-2-methyl-2-propanolate)lead(II), Pb(DMAMP) 2 , and O 3 as the reactants, with a high growth rate of 2.6 Å/cycle. PbO 2 readily reduces under low oxygen partial pressures at moderate temperatures making it challenging to deposit ALD PbO 2 from Pb 2+ precursors. However, thin films deposited with this process showed small crystalline grains of α-PbO 2 and β-PbO 2 , without signs of reduced PbO x phases. The ALD PbO 2 thin films show the high electrical conductivity characteristic of bulk PbO 2 . In situ measurements of ALD PbO 2 film conductivity during growth suggest a reaction mechanism by which sub-surface oxygen mobility contributes to the growth of resistive PbO or PbO x during the Pb(DMAMP) 2 surface reaction step, which is only fully oxidized from Pb 2+ to Pb 4+ during the O 3 reaction step. These films were electrochemically reduced to PbSO 4 in H 2 SO 4 and then reoxidized to PbO 2 , demonstrating their suitability for use as an electrode material for fundamental battery research and other electrochemical applications.

atomic layer deposition↗
NASA NTRS2003

Space Durable Polyimide/Carbon Nanotube Composite Films for Electrostatic Charge Mitigation

Low color, space environmentally durable polymeric films with sufficient electrical conductivity to mitigate electrostatic charge (ESC) build-up have been under investigation as part of a materials development activity. These materials have potential applications on advanced spacecraft, particularly on large, deployable, ultra-light weight Gossamer spacecraft. The approach taken to impart sufficient electrical conductivity into the polymer film is based on the use of single walled carbon nanotubes (SWNT) as conductive additives. Earlier approaches investigated in our lab involved both an in-situ polymerization approach and addition of SWNT to an oligomer containing reactive end-groups as methods to improve SWNT dispersion. The work described herein is based on the spray coating of a SWNT/solvent dispersion onto the film surface. Two types of polyimides were investigated, one with reactive end groups that can lead to bond formation between the oligomer chain and the SWNT surface and those without reactive end-groups. Surface conductivities (measured as surface resistance) in the range sufficient for ESC mitigation were achieved with minimal effects on the mechanical, optical, thermo-optical properties of the film as compared to the other methods. The chemistry and physical properties of these nanocomposites will be discussed.

Watson, Kent A.↗
DOE OSTI2021

A surface acoustic wave hydrogen sensor with tin doped indium oxide layers for intermediate temperatures

We report high temperature surface acoustic wave (SAW) gas sensors with conducting sensing layers require tuning of the sheet conductivity for optimal response. Conducting metal oxides are attractive sensing materials for their tunable electronic properties and high thermal stability, amongst others. Here, we have investigated the application of indium oxide (IO) and indium tin oxide (ITO) films on langasite (LGS)-based SAW reflective delay line sensor devices for monitoring hydrogen at 350 °C. Specifically, we modeled the effect of the IO and ITO sensing layer thickness on the wave velocity, attenuation, and effective electromechanical coefficient. This was followed by an experimental demonstration of tuning of the ITO film sheet conductivity by controlling the dopant concentration and yielding an improvement in the sensor sensitivity. The current study provides a pathway towards the development of conductivity-based sensing layers for high temperature SAW gas sensors with improved sensitivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Transforming an Ionic Conductor into an Electronic Conductor via Crystallization: In Situ Evolution of Transference Numbers and Structure in (La,Sr)(Ga,Fe)O 3–x Perovskite Thin Films

Mixed-conducting perovskites are workhorse electrochemically active materials, but typical high-temperature processing compromises their catalytic activity and chemo-mechanical integrity. Low-temperature pulsed laser deposition of amorphous films plus mild thermal annealing is an emerging route to form homogeneous mixed conductors with exceptional catalytic activity, but little is known about the evolution of the oxide-ion transport and transference numbers during crystallization. Here the coupled evolution of ionic and electronic transport behavior and structure in room-temperature-grown amorphous (La,Sr)(Ga,Fe)O 3-x films as they crystallize is explored. In situ ac-impedance spectroscopy with and without blocking electrodes, simultaneous capturing-synchrotron-grazing-incidence X-ray diffraction, dc polarization, transmission electron microscopy, and molecular dynamics simulations to evaluate isothermal and non-isothermal crystallization effects and the role of grain boundaries on transference numbers is combined. Ionic conductivity increases by ≈2 orders of magnitude during crystallization, with even larger increases in electronic conductivity. Consequently, as crystallinity increases, LSGF transitions from a predominantly ionic conductor to a predominantly electronic conductor. The roles of evolving lattice structural order, microstructure, and defect chemistry are examined. Grain boundaries appear relatively nonblocking electronically but significantly blocking ionically. The results demonstrate that ionic transference numbers can be tailored over a wide range by tuning crystallinity and microstructure without having to change the cation composition.

36 MATERIALS SCIENCE↗
NASA NTRS1978

Method for producing solar energy panels by automation

A solar cell panel was fabricated by photoetching a pattern of collector grid systems with appropriate interconnections and bus bar tabs into a glass or plastic sheet. These regions were then filled with a first, thin conductive metal film followed by a layer of a mixed metal oxide, such as InAsO or InSnO. The multiplicity of solar cells were bonded between the protective sheet at the sites of the collector grid systems and a back electrode substrate by conductive metal filled epoxy to complete the fabrication of an integrated solar panel.

Evans, J. C., Jr.↗
NASA NTRS2004

Chemical stability enhancement of lithium conducting solid electrolyte plates using sputtered LiPON thin film

Sputter deposition of LiPON films directly onto high Li+ conductivity solid electrolyte plates has been investigated as a means to minimize the reactivity of the plates to metallic Li. The LiPON films were shown to effectively passivate the plates in contact with metallic Li, in contrast to unpassivated plates that reacted immediately in contact with Li metal.

LiPON lithium metals electrolyte plates↗
DOE OSTI2024

In-situ TEM EELS analysis of memristive thin films for neuromorphic computing

Neuromorphic computing stands as a promising frontier for advancing AI algorithms and applications like ChatGBT, offering significant energy efficiency gains. This paper delves into the hardware design intricacies of memristive thin films and their elementary switching mechanisms, including anion migration, electron migration, and phase transitions. Through comprehensive analysis of electron energy loss spectroscopy (EELS) data via in-situ transmission electron microscopy (TEM), we will deduce the primary memristive switching mechanisms vital for optimizing thin film fabrication parameters and achieving desired film thickness, conductivity, and memory retention. A single crystal ptype Si substrate was used with TiN as the bottom metal electrode, TiO x as the insulating dielectric layer, and Pt as the top metal electrode. In-situ TEM was able to tell us the thin film didn’t behave like a filamentary or phase transition material. EELS data deduced that electron trapping/detrapping was one of the primary switching mechanisms. By shedding light on these elementary mechanisms, our study aims to catalyze the development of more 2 efficient and effective neuromorphic computing systems to be deployed into mainstream technologies.

97 MATHEMATICS AND COMPUTING↗