Search NASA⌕ Search

SEARCH · Search NASA

Results for “configuration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Effects of angle of attack and vertical fin on transonic flutter characteristics of an arrow-wing configuration

Experimental transonic flutter results are presented for a simplified 1/50 size, aspect ratio 1.77, wind tunnel model of an arrow wing design. Flutter results are presented for two configurations; namely, one with and one without a ventral fin mounted at the 0.694 semispan station. Results are presented for both configurations trimmed to zero lift and in a lifting condition at angles of attack up to 4 deg. The results show that the flutter characteristics of both configurations are similar to those usually observed. Increasing angle of attack reduces the flutter dynamic pressure by a small amount (about 13 percent maximum) for both configurations. The addition of the fin to the basic wing increases the flutter dynamic pressure. Calculated results for both configurations in the nonlifting condition obtained by using subsonic doublet lattice unsteady aerodynamic theory correlate reasonably well with the experimental results. Calculated results for the basic wing obtained by using subsonic kernal function unsteady aerodynamic theory did not agree as well with the experimental data.

Doggett, R. V., Jr.↗
NASA NTRS1980

Integrative application of active controls (IAAC) technology to an advanced subsonic transport project. Initial act configuration design study

The performance and economic benefits of a constrained application of Active Controls Technology (ACT) are identified, and the approach to airplane design is established for subsequent steps leading to the development of a less constrained final ACT configuration. The active controls configurations are measured against a conventional baseline configuration, a state-of-the-art transport, to determine whether the performance and economic changes resulting from ACT merit proceeding with the project. The technology established by the conventional baseline configuration was held constant except for the addition of ACT. The wing, with the same planform, was moved forward on the initial ACT configuration to move the loading range aft relative to the wing mean aerodynamic chord. Wing trailing-edge surfaces and surface controls also were reconfigured for load alleviation and structural stabilization.

Source record↗
NASA NTRS1984

Low-speed wind-tunnel study of the high-angle-of-attack stability and control characteristics of a cranked-arrow-wing fighter configuration

The low-speed, high-angle-of-attack stability and control characteristics of a fighter configuration incorporating a cranked arrow wing were investigated in the Langley 30- by 60-foot tunnel as part of a NASA/General Dynamics cooperative research program to investigate the application of advanced wing designs to combat aircraft. Tests were conducted on a baseline configuration and on several modified configurations. The results show that the baseline configuration exhibited a high level of maximum lift but displayed undesirable longitudinal and lateral-directional stability characteristics at high angles of attack. Various wing modifications were made which improved the longitudinal and lateral-directional stability characteristics of the configuration at high angles of attack. However, most of the modifications were detrimental to maximum lift.

Grafton, S. B.↗
NASA NTRS1984

Validation of a transonic analysis code for use in preliminary design of advanced transport configurations

The WBPPW code has the capability of analyzing flow-field effects about configurations which include wing pylons and engine nacelles or pods in addition to the basic wing/fuselage combination. Using the concept of grid embedding, the code solves the extended small disturbance transonic flow equation for complex flow interactions of the various configuration components. A general description of the code and solution algorithm is included. Results are presented and compared with experiment for various configurations which encompass the code capabilities. These include wing planform and wing contour modifications and variations in nacelle position beneath a high-aspect-ratio wing. Results are analyzed in the light of preliminary design, where the capability to accurately compute flow-field effects resulting from various configuration perturbations is important. The comparisons show that the computational results are sensitive to subtle design modifications and that the code could be used as an effective guide during the design process for transport configurations.

Waggoner, E. G.↗
NASA NTRS1986

Application of a linearized unsteady aerodynamic analysis to standard cascade configurations

A linearized potential flow analysis, which accounts for the effects of nonuniform steady flow phenomena on the linearized unsteady aerodynamic response to prescribed blade motions, has been applied to five cascade configurations. These include the first, fifth, eighth and ninth standard configurations proposed as a result of the Second International Symposium on Aeroelasticity in Turbomachines and a NASA Lewis flutter cascade. Selected results from this study, including comparisons between analytical predictions and the experimental measurements submitted for three of the foregoing configurations, are described. The correlation between theory and experiment for the first standard configuration (a compressor cascade operating at low Mach number and frequency) is quite good. Moreover, the predictions and measurements for the NASA Lewis cascade of symmetric biconvex airfoils show good qualitative agreement. However, wide discrepancies exist between the theoretical predictions and the experimental measurements for the fifth standard configuration (a subsonic transonic fan tip cascade). These can be partially attributed to conditions being imposed in the experiment which differ from those commonly used in unsteady aerodynamic analyses.

Verdon, J. M.↗
NASA NTRS1986

An experimental study of the lift, drag and static longitudinal stability for a three lifting surface configuration

The experimental procedure and aerodynamic force and moment measurements for wind tunnel testing of the three lifting surface configuration (TLC) are described. The influence of nonelliptical lift distributions on lift, drag, and static longitudinal stability are examined; graphs of the lift coefficient versus angle of attack, the pitching moment coefficient, drag coefficient, and lift to drag ratio versus lift coefficient are provided. The TLC data are compared with the conventional tail-aft configuration and the canard-wing configuration; it is concluded that the TLC has better lift and high-lift drag characteristics, lift to drag ratio, and zero-lift moments than the other two configurations. The effects of variations in forward and tail wind incidence angles, gap, stagger, and forward wind span on the drag, lift, longitudinal stability, and zero-lift moments of the configuration are studied.

Ostowari, C.↗
NASA NTRS1987

Subsonic longitudinal and lateral-directional characteristics of a forward-swept-wing fighter configuration at angles of attack up to 47 deg

Subsonic lateral-direction and longitudinal characteristics of a forward-swept-wing fighter configuration were examined in wind-tunnel tests at Mach numbers of 0.2 and 0.5 for angles of attack from -7 to 47 deg. and over a sidelslip range of +/- 15 deg. The effects of a canard, strakes, vertical tail, and leading- and trailing-edge flaps are examined. The canard and strakes both reduce asymmetric moments and side forces at zero sideslip for angles of attack up to about 30 deg. The canard has a small influence on lateral-directional stability; however, strakes produce a substantial reduction in lateral stability for angles of attack greater than about 20 deg. The vertical tail improves directional stability for angles of attack up to 30 deg. Deflection of the leading-edge flap to 20 deg. at high angles of attack on the strake and canard configurations degrades lateral and directional stability. Deflection of the trailing-edge flap to 20 deg. on the canard configuration generally increases lateral and directional stability at high angles of attack. Leading- and trailing-edge flaps on the wing-body and canard configurations are effective for increased lift only for angles of attack up to about 40 deg. The leading-edge flap remains effective on the strake configuration over the entire angle-of-attack range tested.

Mann, Michael J.↗
NASA NTRS1987

Low-speed aerodynamic characteristics of a twin-engine general aviation configuration with aft-fuselage-mounted pusher propellers

An investigation was conducted to determine the aerodynamic characteristics of an advanced turboprop aircraft model with aft-pylon-mounted pusher propellers. Tests were conducted through an angle-of-attack range of -8 to 28 degrees, and an angle-of-sideslip range of -20 to 20 degrees at free-stream conditions corresponding to Reynolds numbers of 0.55 to 2.14 x 10 to the 6th power based on mean aerodynamic chord. Test results show that for the unpowered configurations the maximum lift coefficients for the cruise, takeoff, and landing configurations are 1.45, 1.90, and 2.10, respectively. Nacelle installation results in a drag coefficient increase of 0.01. Increasing propeller thrust results in a significant increase in lift for angles of attack above stall and improves the longitudinal stability. The cruise configuration remains longitudinally stable to an angle of attack 5 degrees beyond the stall angle, the takeoff configuration is stable 4 degrees beyond stall angle, and the landing configuration is stable 3 degrees beyond stall angle. The predominant effect of symmetric thrust on the lateral-directional aerodynamic characteristics is in the post-stall region, where additional rudder control is available with power on.

Dunham, Dana Morris↗
NASA NTRS1986

Exploratory wind-tunnel investigation of the stability and control characteristics of advanced general aviation configurations

Results of low-speed wind-tunnel investigations are presented for two general aviation configurations: the AVTEK canard configuration and the DeVore conventional configuration. Cooperative research programs were undertaken by industry and NASA to jointly conduct tests in the NASA Langley 12-Foot Low-Speed Wind Tunnel to explore stability and control characteristics of each configuration. A 1/5-scale AVTEK model and a 1/6-scale DeVore model were tested over an angle-of-attack range of up to 45 deg and an angle-of-sideslip range of up to 20 deg. Results from the AVTEK test are presented with an emphasis on the effects of configuration on the stall and poststall characteristics. Results from the DeVore test are presented with emphasis on the effects of wing leading-edge droop design on spin resistance characteristics.

Yip, L. P.↗
NASA NTRS1987

Optimization of V-groove radiator configuration

In the design of spacecraft radiators intended to provide cryogenic cooling, it is important to minimize the space occupied by radiator shielding while satisfying the performance requirements. This study develops and tests the first step toward optimizing radiator shield configurations and examines the design of the highly effective V-groove radiator concept. This investigation, which makes use of a special purpose Monte Carlo/ray tracing computer program, directly identifies the two shield configuration which minimizes radiator footprint for a given temperature drop. Furthermore, multiple shield configurations may be analyzed through a combination of analysis and program statistics. The results presented demonstrate the sensitivity of intershield temperature drop to shield angle and/or offset and provide a comparison of angled and parallel shield configurations. Good agreement with experimental data is shown for a multiple shield configuration.

Schember, Helene R.↗
NASA NTRS1988

Space shuttle phase B wind tunnel model and test information. Volume 2: Orbiter configuration

Archived wind tunnel test data are available for flyback booster or other alternate recoverable configurations as well as reusable orbiters studied during initial development (Phase B) of the Space Shuttle. Considerable wind tunnel data was acquired by the competing contractors and the NASA centers for an extensive variety of configurations with an array of wing and body planforms. All contractor and NASA wind tunnel test data acquiredin the Phase B development have been compiled into a database and are available for applying to current winged flyback or recoverable booster aerodynamic studies. The Space Shuttle Phase B Wind Tunnel Database is structured by vehicle component and configuration type. Basic components include the booster, the orbiter, and the launch vehicle. Booster configuration types include straight and delta wings, canard, cylindrical, retroglide, and twin body. Orbiter configuration types include straight and delta wings, lifting body, drop tanks, and double delta wings. Launch configration types include booster and orbiter components in various stacked and tandom combinations. The digital database consists of 220 files of data containing basic tunnel recorded data.

Glynn, J. L.↗
NASA NTRS1987

Kinematic study of flight telerobotic servicer configuration issues

Several factors, such as body size and shape, and the number of arms and their placement, will influence how well the Flight Telerobotic Servicer (FTS) is suited to its potential duties for the Space Station Program. In order to examine the implications of these configuration options, eight specific 2, 3, and 4 armed FTS configuration were simulated and used to perform a Space Station Orbital Replacement Unit (ORU) exchange. The strengths and weaknesses of each configuration were evaluated. Although most of the configurations examined were able to perform the exchange, several of the 3 and 4 arm configurations had operational advantages. The results obtained form these simulations are specific to the assumptions associated with the ORU exchange scenario examined. However, they do illustrate the general interrelationships and sensitivities which need to be understood.

Lewis, R. H.↗
NASA NTRS1989

AGARD standard aeroelastic configurations for dynamic response

Since emphasis is on the transonic speed range, special importance is placed on configurations for which available data are sufficient to define accurately a transonic flutter boundary. Only configurations with clean, smooth surfaces are considered suitable. Segmented models or models with surface-slope discontinuities are inappropriate. Excluded also, in general, are configurations and data sets that involve behavior that is uncertain or not well understood, uncertain model properties, or know sensitivities to small variations in model properties. In order to assess the suitability of configurations already tested and the associated data for designation as standard, a survey of AGARD member countries was conducted to seek candidates for the prospective set. The results of that survey are given and summarized along with the initial selection of a standard configuration.

Yates, E. Carson, Jr.↗
NASA NTRS1989

Low-speed static and dynamic force tests of a generic supersonic cruise fighter configuration

Static and dynamic force tests of a generic fighter configuration designed for sustained supersonic flight were conducted in the Langley 30- by 60-foot tunnel. The baseline configuration had a 65 deg arrow wing, twin wing mounted vertical tails and a canard. Results showed that control was available up to C sub L,max (maximum lift coefficient) from aerodynamic controls about all axes but control in the pitch and yaw axes decreased rapidly in the post-stall angle-of-attack region. The baseline configuration showed stable lateral-directional characteristics at low angles of attack but directional stability occurred near alpha = 25 deg as the wing shielded the vertical tails. The configuration showed positive effective dihedral throughout the test angle-of-attack range. Forced oscillation tests indicated that the baseline configuration had stable damping characteristics about the lateral-directional axes.

Hahne, David E.↗
NASA NTRS1989

An Approximate Model for the Performance and Acoustic Predictions of Counterrotating Propeller Configurations

An approximate method was developed to analyze and predict the acoustics of a counterrotating propeller configuration. The method employs the analytical techniques of Lock and Theodorsen as described by Davidson to predict the steady performance of a counterrotating configuration. Then, a modification of the method of Lesieutre is used to predict the unsteady forces on the blades. Finally, the steady and unsteady loads are used in the numerical method of Succi to predict the unsteady acoustics of the propeller. The numerical results are compared with experimental acoustic measurements of a counterrotating propeller configuration by Gazzaniga operating under several combinations of advance ratio, blade pitch, and number of blades. In addition, a constant-speed commuter-class propeller configuration was designed with the Davidson method and the acoustics analyzed at three advance ratios. Noise levels and frequency spectra were calculated at a number of locations around the configuration. The directivity patterns of the harmonics in both the horizontal and vertical planes were examined, with the conclusion that the noise levels of the even harmonics are relatively independent of direction whereas the noise levels of the odd harmonics are extremely dependent on azimuthal direction in the horizontal plane. The equations of Succi are examined to explain this behavior.

Denner, Brett William↗
NASA NTRS1989

Case studies in configuration control for redundant robots

A simple approach to configuration control of redundant robots is presented. The redundancy is utilized to control the robot configuration directly in task space, where the task will be performed. A number of task-related kinematic functions are defined and combined with the end-effector coordinates to form a set of configuration variables. An adaptive control scheme is then utilized to ensure that the configuration variables track the desired reference trajectories as closely as possible. Simulation results are presented to illustrate the control scheme. The scheme has also been implemented for direct online control of a PUMA industrial robot, and experimental results are presented. The simulation and experimental results validate the configuration control scheme for performing various realistic tasks.

Seraji, H.↗
NASA NTRS1989

Some aerodynamic characteristics of the scissor wing configuration

A scissor wing configuration, consisting of four adjustable wing surfaces, is compared with a comparable fixed wing baseline configuration. Wave drag, induced drag, viscous drag, thrust required, and gust loading are calculated for both configurations. The scissor wing is shown to have lower zero lift wave drag and higher total lift to drag ratios than the baseline. It is demonstrated that the scissor configurations' sweep can be programmed to keep the static margin fixed. Thrust required for both the fixed static margin case and a constant sweep angle case are presented with the scissor configuration requiring lower thrust levels. The gust loading ratio of the scissor wing to the baseline is also shown to be significantly less than 1.0 for sweep angles greater than 20 degrees.

Selberg, Bruce P.↗
NASA NTRS1990

Dynamics and configurations of galaxy triplets

The purpose is to infer the probable dynamical states of galaxy triplets by the observed data on their configurations. Two methods are proposed for describing the distributions of the triplet configuration parameters characterizing a tendency to alignment and hierarchy: (1) obtaining a representative sample of configurations and determining its statistical parameters (moments and percentages); and (2) dividing the region of possible configurations of triple systems (Agekian and Anosova, 1967) into a set of segments and finding the probabilities for the configurations to find themselves in each of them. Both these methods allow representation of the data by numerical simulations as well as observations. The effect of projection was studied. It rather overestimates the alignment and hierarchy of the triple systems. Among the parameters of interest there are found some parameters that are least sensitive to projection effects. The samples consist of simulated galaxy triplets (with hidden mass) as well as of 46 probably physical triple galaxies (Karachentseva et al., 1979). The observed triples as well as numerical models show a tendency to alignment. The triple galaxies do not show any tendency to hierarchy (formation of the temporary binaries), but this tendency may be present for simulated triplets without significant dark matter. The significant hidden mass (of order ten times the total mass of a triplet) decreases the probability of forming a binary and so weakens the hierarchy. Small galaxy groups consisting of 3 to 7 members are probably the most prevalent types of galaxy aggregate (Gorbatsky, 1987). Galaxy triplets are the simplest groups, but dynamically nontrivial ones.

Anosova, Joanna P.↗