Search NASA⌕ Search

SEARCH · Search NASA

Results for “continuum”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Day 640 infrared line and continuum measurements: Dust formation in SN 1987A

We have measured day 640-645 line and continuum spectra of (Ni II) 6.6 micrometer (Ne II) 12.8 micrometer (line emission was not detected), and (Fe II) 17.9 and 26.0 micrometer from SN 1987A. The high velocity feature at v(sub HVF) approximately 3900 km/sec found in both of our day 410 (Fe II) spectra is again detected in the day 640 (Ni II) spectrum, although the signal-to-noise of the day 640 (Fe II) spectra is insufficient to show this feature. The continuum fluxes provide clear evidence for the formation of dust between day 410 and day 640 and are best fitted by a graybody spectrum with a temperature of 342 +/- 17 K at day 640 and a surface area corresponding to a minimum dust velocity v(sub dust) = 1910 +/- 170 km/sec. Optically thin dust emissivity laws proportional to lambda(exp -1) or lambda(exp -2) are inconsistent with the data. Either the dust grains are large (radius a much greater than 4 micrometer and radiate like individual blackbodies, or else they are located in clumps optically thick in the 6-26 micrometer range. The (Ni II) 6.6 micrometer line flux yields a minimum Ni(+) mass of 5.8 +/- 1.6 x 10(exp -4) solar mass and a Ni/Fe abundance ratio of 0.06 +/- 0.02, equal to the solar value. The ratio of the two (Fe II) line profiles implies a gas temperature 2600 +/- 700 K, a drop of 1800 +/- 800 K from our day 410 measurement. The (Fe II) 26.0 micrometer line flux has decreased by a factor of 2 and the day 640 (Ni II) profile is blueshifted by -440 +/- 270 km/sec, relative to observations before day 500. We show that the decrease in the (Fe II) flux and the blueshift are not produced by a decrease in electron scattering optical depth, electron density, or temperature, but rather are probably due to obscuration by the same dust which produces the infrared continuum. This supports the interpretation that the dust spectrum is produced by optically thick clumps. We discuss possible explanations for the discrepancy between the mass of Fe(+) detected and the total iron mass required to power the light curve. The decrease in the (Fe II) fluxes relative to the decrease required to account for the blueshifts of optical lines from non-iron-group elements and the similarity between v(sub dust) and the Ni(+) expansion velocity imply a spatial association between the dust clumps and the iron-group elements. In addition, the larger blueshift observed for the near and far-infrared, heavy metal transitions relative to non-iron-group lines suggests that the iron-group elements are somewhat segregated from lighter elements such as the Mg(sup 0) and O(sup 0) responsible for shorter wavelength lines. We speculate that FeS may be an important constituent of the dust. A comparison of our line profiles with radiative transfer models shows that while power law and exponential density distributions yield reasonable fits to the data, polytrope distributions provided significantly worse agreement. The best fits require a substantial fraction of the iron to be undetectable, and are consistent with maximum expansion velocities of v(sub max) approximately 3000 km/sec.

Colgan, Sean W. J.↗
NASA NTRS1996

Continuum Fatigue Damage Modeling for Critical Design, Control, and Fault Prognosis

This paper develops a simplified continuum (continuous with respect to time, stress, etc.) fatigue damage model for use in critical design, Life Extending Control and fault prognosis. The work is based on the local strain cyclic damage modeling method. New nonlinear explicit equation forms of cyclic damage in terms of stress amplitude are derived to facilitate the continuum modelling. Stress based continuum models are derived. Extension to plastic strain-strain rate models is also presented. Progress toward a non-zero mean stress based is presented. Also new nonlinear explicit equation forms in terms of stress amplitude are derived for this case. Application of the various models to design, control, and fault prognosis is considered.

Lorenzo, Carl F.↗
NASA NTRS1994

Low-Density Nozzle Flow by the Direct Simulation Monte Carlo and Continuum Methods

Two different approaches, the direct simulation Monte Carlo (DSMC) method based on molecular gasdynamics, and a finite-volume approximation of the Navier-Stokes equations, which are based on continuum gasdynamics, are employed in the analysis of a low-density gas flow in a small converging-diverging nozzle. The fluid experiences various kinds of flow regimes including continuum, slip, transition, and free-molecular. Results from the two numerical methods are compared with Rothe's experimental data, in which density and rotational temperature variations along the centerline and at various locations inside a low-density nozzle were measured by the electron-beam fluorescence technique. The continuum approach showed good agreement with the experimental data as far as density is concerned. The results from the DSMC method showed good agreement with the experimental data, both in the density and the rotational temperature. It is also shown that the simulation parameters, such as the gas/surface interaction model, the energy exchange model between rotational and translational modes, and the viscosity-temperature exponent, have substantial effects on the results of the DSMC method.

Chung, Chang-Hong↗
NASA NTRS1996

The Lyman-Continuum Fluxes and Stellar Parameters of O and Early B-Type Stars

Using the results of the most recent stellar atmosphere models applied to a sample of hot stars, we construct calibrations of effective temperature (T(sub eff)), and gravity (log(sub g)) with a spectral type and luminosity class for Galactic 0-type and early B-type stars. From the model results we also derive an empirical relation between the bolometric correction and T(sub eff) and log g. Using a sample of stars with known distances located in OB associations in the Galaxy and the Large Magellanic Cloud, we derive a new calibration of M(sub v) with spectral class. With these new calibrations and the stellar atmosphere models of Kurucz, we calculate the physical parameters and ionizing photon luminosities in the H(0) and He(0) continua for O and early B-type stars. We find substantial differences between our values of the Lyman- continuum luminosity and those reported in the literature. We also discuss the systematic discrepancy between O-type stellar masses derived from spectroscopic models and those derived from evolutionary tracks. Most likely, the cause of this 'mass discrepancy' lies primarily in the atmospheric models, which are plane parallel and hydrostatic and therefore do not account for an extended atmosphere and the velocity fields in a stellar wind. Finally, we present a new computation of the Lyman-continuum luminosity from 429 known O stars located within 2.5 kpc of the Sun. We find the total ionizing luminosity from this population ((Q(sub 0)(sup T(sub ot))) = 7.0 x 10(exp 51) photons/s) to be 47% larger than that determined using the Lyman continuum values tabulated by Panagia.

Vacca, William D.↗
NASA NTRS1997

The High-Energy Continuum Emission of the Gamma-Ray Blazar PKS 0528+134

We present Advanced Satellite for Cosmology and Astrophysics (ASCA) observations of the gamma-ray blazar PKS 0528 + 134, obtained at two separate epochs in 1994 August and 1995 March. These data represent the first measurement of the X-ray continuum emission of this source in the medium-hard X-ray band. Both ASCA spectra are consistent with a single power law with photon index GAMMA approximate 1.7-1.8 and column density N(sub H) approximately 5 x 10(exp 21) /sq cm, higher than Galactic. The X-ray flux increased by a factor of 4 in approximately 7 months without appreciable change of the spectral shape. During the lower state of 1994 August, PKS 0528 + 134 was observed simultaneously in the optical, X-rays, and at gamma-ray energies with EGRET. The gamma-ray intensity is the faintest detected thus far in the source, with a steep spectrum (GAMMA approximately 2.7). The extrapolation of the X-ray continuum to the gamma-ray range requires a sharp spectral break at approximately 10(exp 22) Hz. We discuss the radio through gamma-ray spectral energy distribution of PKS 0528 + 134, comparing the low state of 1994 August with the flare state of 1993 March. We show that in PKS 0528 + 134, a non-negligible contribution from the external radiation field is present and that, although synchrotron self-Compton scenarios cannot be ruled out, inverse Compton upscattering of thermal seed photons may be the dominant cooling process for the production of the high-energy continuum in this blazar.

Sambruna, Rita M.↗
NASA NTRS1997

The High-energy Continuum Emission of the Gamma-Ray Blazar PKS 0528+134

We present Advanced Satellite for Cosmology and Astrophysics (ASCA) observations of the gamma-ray blazar PKS 0528 + 134, obtained at two separate epochs in 1994 August and 1995 March. These data represent the first measurement of the X-ray continuum emission of this source in the medium-hard X-ray band. Both ASCA spectra are consistent with a single power law with photon index GAMMA approx. = 1.7-1.8 and column density N(sub H) approx. = 5 x 10(exp 21)/ sq cm, higher than Galactic. The X-ray flux increased by a factor of 4 in approx. 7 months without appreciable change of the spectral shape. During the lower state of 1994 August, PKS 0528 + 134 was observed simultaneously in the optical, X-rays, and at gamma-ray energies with Energetic Gamma Ray Experiment Telescope (EGRET). The gamma-ray intensity is the faintest detected thus far in the source, with a steep spectrum (GAMMA approx. = 2.7). The extrapolation of the X-ray continuum to the gamma-ray range requires a sharp spectral break at approx. 10(exp 22) Hz. We discuss the radio through gamma-ray spectral energy distribution of PKS 0528 + 134, comparing the low state of 1994 August with the flare state of 1993 March. We show that in PKS 0528 + 134, a non-negligible contribution from the external radiation field is present and that, although synchrotron self-Compton scenarios cannot be ruled out, inverse Compton upscattering of thermal seed photons may be the dominant cooling process for the production of the high-energy continuum in this blazar.

Sambruna, Rita M.↗
NASA NTRS2000

The Non-Stellar Infrared Continuum of Seyfert Galaxies

JHKL'M (1 - 5 micrometers) imaging of a sample of Seyfert 2 galaxies is presented. We have performed an accurate estimate of the near-infrared non-stellar nuclear fluxes. We confirm that the near-infrared nuclear continuum between 1 and 2.2microns of some Seyfert 2s is dominated by stellar emission, whereas the continuum emission at longer wavelengths (lambda = 3 - 5 micrometers) is almost entirely non-stellar in origin. The non-stellar spectral energy distributions (SED) in the infrared (up to 15 micrometers) of Seyfert galaxies show a variety of shapes, and they are well reproduced with the tapered disk models of Efstathiou & Rowan-Robinson (1995). We have used two models, one including an optically thin cone component found to fit the SED of NGC 1068, and a coneless model. Although our modelling of the SEDs does not allow us to favor either model to account for all the observed SEDs, we find that the viewing angle towards the central source is well constrained by both models. The galaxies in our sample have fitted values of the viewing angle in the range Theta(sub V) = 0 deg - 64 deg, for the assumed model parameters. We have also investigated non-stellar color-color diagrams (L' - M vs. H - M and L' - M vs. H - L'). The colors of the Seyfert galaxies with viewing angles Theta(sub v) less than 30 deg are better reproduced with the cone model. These diagrams provide a good means to separate Seyfert 2s with moderate obscuration (A(sub V) approx. less than 20 mag from hard X-ray observations) from those with high obscuration. The ground-based 4.8 microns and ISO 9.6 microns luminosities are well correlated with the hard X-ray luminosities of Seyfert ls and 2s. These continuum emissions appear as a good indicator of the AGN luminosity, at least in the cases of hard X-ray Compton-thin Seyfert galaxies (N(sub H) less than or = 10(exp 24)/sq cm). We finally stress the finding that some Compton thick galaxies show bright non-stellar emission at 5 microns This suggests that the near-infrared emission in Seyfert galaxies is produced in an extended component illuminated by the central source, that is more visible from all viewing angles, providing a good explanation for the differing N(sub H)/A(sub V) ratios found in some Seyfert 2s. We discuss possible implications of mid-infrared surveys for the search of counterparts of highly obscured hard X-ray sources.

Alonso-Herrero, Almudena↗
NASA NTRS1997

Numerical Study of a Continuum Sonic Jet Interacting with a Rarefield Flow

The results of a numerical study with flow and boundary conditions based on an experiment of a continuum sonic jet interacting with rarefied flow about a sharp leading edge flat plate at zero incidence are presented. Comparisons are made between computational fluid dynamics (CFD) and direct simulation Monte Carlo (DSMC) solutions which provide an assessment of applying each technique to the flow conditions of the experiment. An analysis of the CFD results revealed a correlation between the interaction interface of the jet continuum breakdown surface and a non-dimensional parameter derived from jet and free stream flow conditions. Using the breakdown surface from the correlation, the continuum jet was uncoupled from the interaction, thus allowing an uncoupled CFD-DSMC solution to be obtained. Also, a nearest neighbor collision algorithm, similar to the subcell technique, was implemented in the DSMC solution technique. The comparison between CFD and DSMC results shows good qualitative agreement in the interaction region and good quantitative agreement elsewhere.

Glass, Christoper E.↗
NASA NTRS2017

A Hybrid Line List for CH4 and Hot Methane Continuum

Molecular line lists (a catalogue of transition frequencies and line strengths) are important for modelling absorption and emission processes in atmospheres of different astronomical objects, such as cool stars and exoplanets. In order to be applicable for high temperatures, line lists for molecules like methane must contain billions of transitions, which makes their direct (line-by-line) application in radiative transfer calculations impracticable. Here we suggest a new, hybrid line list format to mitigate this problem, based on the idea of temperature-dependent absorption continuum. Methods. The line list is partitioned into a large set of relatively weak lines and a small set of important, stronger lines. The weaker lines are then used either to construct a temperature-dependent (but pressure-independent) set of intensity cross sections or are blended into a greatly reduced set of super-lines. The strong lines are kept in the form of temperature independent Einstein A coefficients. Results. A line list for methane is constructed as a combination of 17 million strong absorption lines relative to the reference absorption spectra and a background methane continuum in two temperature-dependent forms, of cross sections and super-lines. This approach eases the use of large high temperature line lists significantly as the computationally expensive calculation of pressure dependent profiles only need to be performed for a relatively small number of lines. Both the line list and cross sections were generated using a new 34 billion methane line list (34 to10), which extends the 10to10 line list to higher temperatures (up to 2000 K). The new hybrid scheme can be applied to any large line lists containing billions of transitions. We recommend to use super-lines generated on a high resolution grid based on resolving power R = 1,000,000 to model the molecular continuum as a more flexible alternative to the temperature dependent cross sections.

Line Profiles↗
NASA NTRS2021

SoMo: Fast and Accurate Simulations of Continuum Robots in Complex Environments

Engineers and scientists often rely on their intuition and experience when designing soft robotic systems. The development of performant controllers and motion plans for these systems commonly requires time-consuming iterations on hardware. We present the SoMo (Soft Motion) toolkit, a software framework that makes it easy to instantiate and control typical continuum manipulators in an accurate physics simulator. SoMo introduces a standardized and human-readable description format for continuum manipulators. It leverages this description format and the Bullet physics engine to enable fast and accurate simulations of soft and soft-rigid hybrid robots in environments with complex contact interactions. This allows users to vary design and control parameters across simulations with minimal effort. We compare the capabilities of SoMo to other physics simulators and highlight the benefits and accuracy of SoMo by demonstrating the agreement between simulation and real-world experiments on several examples; these include an in-hand manipulation task with continuum fingers, an automated exploration of how to design soft fingers for precision grasping, and a brief snake locomotion study. Overall, SoMo provides an accessible way for designers of soft robotic hardware and control systems to gain access to a simulation-accelerated workflow.

Moritz A. Graule↗
DOE OSTI2020

Fifth-degree elastic energy for predictive continuum stress-strain relations and elastic instabilities under large strain and complex loading in silicon

Materials under complex loading develop large strains and often phase transformation via an elastic instability, as observed in both simple and complex systems. Here, we represent a material (exemplified for Si I) under large Lagrangian strains within a continuum description by a 5th-order elastic energy found by minimizing error relative to density functional theory (DFT) results. The Cauchy stress—Lagrangian strain curves for arbitrary complex loadings are in excellent correspondence with DFT results, including the elastic instability driving the Si I → II phase transformation (PT) and the shear instabilities. PT conditions for Si I → II under action of cubic axial stresses are linear in Cauchy stresses in agreement with DFT predictions. Such continuum elastic energy permits study of elastic instabilities and orientational dependence leading to different PTs, slip, twinning, or fracture, providing a fundamental basis for continuum physics simulations of crystal behavior under extreme loading.

Levitas, Valery↗
NASA NTRS2001

Ranges of applicability for the continuum beam model in the mechanics of carbon nanotubes and nanorods

Limitations in the validity of the continuum beam model for carbon nanotubes (NTs) and nanorods are examined. Applicability of all assumptions used in the model is restricted by the two criteria for geometric parameters that characterize the structure of NTs. The key non-dimensional parameters that control the NT buckling behavior are derived via dimensional analysis of the nanomechanical problem. A mechanical law of geometric similitude for NT buckling is extended from continuum mechanics for different molecular structures. A model applicability map, where two classes of beam-like NTs are identified, is constructed for distinct ranges of non-dimensional parameters. Expressions for the critical buckling loads and strains are tailored for two classes of NTs and compared with the data provided by the molecular dynamics simulations. copyright 2001 Elsevier Science Ltd. All rights reserved.

Continuum beam model↗
DOE OSTI2022

Coupled continuum and network model framework to study catalyst layers of polymer electrolyte fuel cells

The nanostructured thin film (NSTF) catalyst layers which have demonstrated high power densities, mass activities, and exceptional metal and support stability can have limited operational robustness due to their thin thickness and the hydrophilicity of the metal-coated nano whiskers. The dispersed nanostructured thin film (dNSTF) catalyst layers have been developed by dispersing the NSTF Pt whiskers with ionomer and carbon support to increase the thickness and hydrophobicity. Continuum and network models (NM) are coupled through boundary conditions to study the polymer electrolyte fuel cell with a dNSTF cathode catalyst layer. The coupled model combines the computational efficiency of the continuum model with the pore-scale information in the dNSTF cathode catalyst layer of the NM. It captures the special morphology of the partially ionomer/water covered cylindrical whiskers, as well as water percolation through the pore structures and their impact on the cell performance. Here we observe optimal ionomer coverage on whiskers to be 0.5, ionomer to carbon ratio to be 0.9 and higher whisker to carbon ratios to be desired.

08 HYDROGEN↗
DOE OSTI2023

Assessing continuum plasticity postulates with grain stress and local strain measurements in triaxially compressed sand

Critical state and continuum plasticity theories have been used in research and engineering practice in soil and rock mechanics for decades. These theories rely on postulated relationships between material stresses and strains. Some classical postulates include coaxiality between stress and strain rates, stress–dilatancy relationships, and kinematic assumptions in shear bands. Although numerical and experimental data have quantified the strains and grain kinematics in such experiments, little data quantifying grain stresses are available. Here, we report the first-known grain stress and local strain measurements in triaxial compression tests on synthetic quartz sands using synchrotron X-ray tomography and 3D X-ray diffraction. We use these data to examine the micromechanics of shear banding, with a focus on coaxiality, stress-dilatancy, and kinematics within bands. Our results indicate the following: 1) elevated deviatoric stress, strain, and stress ratios in shear bands throughout experiments; 2) coaxial principal compressive stresses and strains throughout samples; 3) significant contraction along shear bands; 4) vanishing volumetric strain but nonvanishing stress fluctuations throughout samples at all stages of deformation. Our results provide some of the first-known in situ stress and strain measurements able to aid in critically evaluating postulates employed in continuum plasticity and strain localization theories for sands.

42 ENGINEERING↗
DOE OSTI2026

Continuum radiated power density $(P^{\textrm{C}}_{\textrm{rad}})$ and effective charge $(Z_{\textrm{eff}})$ estimates from multi-energy photon-counting measurements

Multi-energy soft x-ray pinhole cameras have been designed, built, calibrated, and operated at Madison symmetric Torus, Alcator C-Mod, and more recently at Tokamak a configuration variable and Tungsten Environment in Steady-State Tokamak (WEST), to measure plasma emission across multiple energy ranges. Here we describe a new methodology to estimate the local continuum radiated power density and the plasma effective charge (Z eff ) directly from photon-counting measurements of the line-free continuum emission (Bremsstrahlung and Radiative Recombination) in several energy bands between 11 and 18 keV. This capability is particularly valuable for confinement systems using metal plasma-facing components, where x-ray losses from interactions with the sputtered wall can represent a significant fraction of the total radiated power (P rad ). The approach leverages a well-characterized detector responsivity, modeled by a complementary error function, and interprets the differential multi-energy measurements between adjacent energy levels through the probability density function of a Gaussian distribution. The implementation of this diagnostic technique is currently under development on the WEST tokamak, aiming at the goal of providing real-time P rad and Z eff measurements during long-pulse operation (up to 1000 s) in the 2026 campaign.

WEST↗
DOE OSTI2024

Energy-dependent implementation of secondary electron emission models in continuum kinetic sheath simulations

The plasma-material interactions present in multiple fusion and propulsion concepts between the flow of plasma through a channel and a material wall drive the emission of secondary electrons. This emission is capable of altering the fundamental structure of the sheath region, significantly changing the expected particle fluxes to the wall. The emission spectrum is separated into two major energy regimes, a peak of elastically backscattered primary electrons at the incoming energy, and cold secondary electrons inelastically emitted directly from the material. The ability of continuum kinetic simulations to accurately represent the secondary electron emission is limited by relevant models being formulated in terms of monoenergetic particle interactions which cannot be applied directly to the discrete distribution function. As a result, rigorous implementation of energy-dependent physics is often neglected in favor of simplified, constant models. We present here a novel implementation of semi-empirical models in the boundary of continuum kinetic simulations which allows the full range of this emission to be accurately captured in physically-relevant regimes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2019

The CO2-Broadened H2O Continuum in the 100-1500 cm(sup -1) Region: Measurements, Predictions and Empirical Model

Transmission spectra of H2O+CO2 mixtures have been recorded, at 296, 325 and 366 K, for various pressures and mixture compositions using two experimental setups. Their analysis enables to retrieve values of the “continuum” absorption by the CO2-broadened H2O line wings between 100 and 1500 cm(exp -1). The results are in good agreement with those, around 1300 cm(exp -1), of the single previous experimental study available. Comparisons are also made with direct predictions based on line-shape correction factors X calculated, almost thirty years ago, using a quasistatic approach and an input H2O-CO2 intermolecular potential. They show that this model quite nicely predicts, with slightly overestimated values, the continuum over a spectral range where it varies by more than three orders of magnitude. An empirical correction is proposed, based on the experimental data, which should be useful for radiative transfer and climate studies in CO2 rich planetary atmospheres.

CO2↗