Search NASA⌕ Search

SEARCH · Search NASA

Results for “damage evolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Residual Stress Modeling and Advanced Diffraction Measurements of 347H Steel Weldments

The 347H stainless steel is a primary high-temperature material for many energy and power generation industries. Stress relief cracking (SRC) has been a particular concern in welding of this material. The residual stress induced by welding and its evolution during post-welding heat treatment (PWHT) and subsequent operating and service conditions is one of the primary factors contributing to SRC. The lifetime of welded structure components is also controlled by the precipitation kinetics that accompanies PWHT, stress relaxation process, and long-term aging and complex synergistic factors. Various theories have been proposed in the past to explain SRC. However, a widely accepted approach to predicting the entire damage evolution and the resulting performance reduction is still lacking. This study is to demonstrate a reliable solution for two critical issues that affect the predictions. First, the residual stress distribution obtained from both simulation and neutron diffraction is compared, which increases the accuracy of mechanical analysis simulation model and therefore builds a solid basis for the lifetime prediction model. Second, the generation, evolution, and annihilation of precipitates are monitored by the synchrotron diffraction experiment. Preliminary results demonstrate the critical importance of precipitation kinetics on the residual stress distribution/redistribution during heat treatments.

Yang, Yi↗

A semi-implicit integration scheme for the stress update of viscoSCRAM

This report documents three improvements made to the implementation of a historically significant material model used in W13 for simulations involving components made of PBX9501. ViscoSCRAM combines linear viscoelasticity with isotropic damage evolution based on fracture mechanics concepts. The original implementation was focused on short duration transient events, thus an explicit update scheme was used. For longer duration simulations which employ relatively larger time step sizes the explicit update scheme is inadequate. This work presents a new semi-implicit update scheme suitable for simulations using relatively large time steps. The algorithm solves a nonlinear system of equations to ensure that the stress, damaged state, and internal (Maxwell) stresses are in agreement with implicit update equations at the end of each increment. The crack growth is advanced in time using a subincremental explicit scheme, thus the entire implementation is semi-implicit. Additionally, modifications to the crack growth kinetics are proposed and implemented obviating the need for an empirical tensile damage growth rate (TDGR) multiplier used in previous implementations. Finally, an automatic time stepping algorithm is implemented to adjust the time step size based on error estimates for the generalized Maxwell model update scheme. Model parameters are fit to existing data and example problems are simulated using both new and legacy implementations to assess comparative advantages and disadvantages.

Engineering(42)↗

SCM Paste Samples Exposed To Aggressive Solutions. Cementitious Barriers Partnership

This report summarizes experimental work performed by SIMCO Technologies Inc. (SIMCO) as part of the Cementitious Barriers Partnership (CBP) project. The test series followed an experimental program dedicated to the study of ordinary Portland cement (OPC) hydrated cement pastes exposed to aggressive solutions. In the present study, the scope is extended to hydrated cement pastes incorporating supplementary cementitious materials (SCM) such as fly ash and ground granulated blast furnace slag (GGBFS). Also, the range of aggressive contact solutions was expanded. The experimental program aimed at testing aggressive contact solutions that more closely mimic the chemical composition of saltstone pore solution. Five different solutions, some of which incorporated high levels of carbonate and nitrate, were placed in contact with four different hydrated cement paste mixes. In all solutions, 150 mmol/L of SO 4 2– (14 400 ppm) were present. The solutions included different pH conditions and different sodium content. Two paste mixes were equivalent to Vault 1/4 and Vault 2 concrete mixes used at SRS in storage structures. Two additional paste mixes, cast at the same water-to-cement ratio and using the same cements but without SCMs, were also tested. The damage evolution in samples was monitored using ultrasonic pulse velocity (UPV) and mass measurements. After three and twelve months of exposure conditions, samples were taken out of solution containers and analyzed to perform migration tests and porosity measurements. Globally, results were in line with the previous study and confirmed that high pH may limit the formation of some deleterious phases like gypsum. In this case, ettringite may form but is not necessarily associated with damage. However, the high concentration of sodium may be associated with the formation of an AFm-like mineral called U-phase. The most significant evidences of damage were all associated with the Vault 2 paste analog. This material proved very sensitive to high pH. All measurement techniques used to monitor and evaluate damage to samples indicated significant alterations to this mix when immersed in contact solutions containing sodium hydroxide. It was hypothesized that the low cement content, combined with high silica content coming from silica fume, fly ash and GGBFS led to the presence unreacted silica. It is possible that the pozzolanic reaction of these SCMs could not be activated due to the low alkali content, a direct consequence of low cement content. In this scenario, the material end up having a lot of silica available to react upon contact with sodium hydroxide, possibly forming a gel that may be similar to the gel formed in alkali-silica reactions. This scenario needs further experimental confirmation, but it may well explain the poor behavior of mix PV2 in presence of NaOH.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effect of Loading Frequency on Fatigue Behavior of Additively Manufactured Short Fiber Thermoplastics via Infrared Thermography

Fracture, Fatigue, Failure, Damage Evolution and Thermomechanics & Infrared Imaging, Volume 4 of the Proceedings of the 2025 SEM Annual Conference & Exposition on Experimental and Applied Mechanics, the fourth volume of five from the Conference, brings together contributions to this important area of research and engineering. The collection presents early findings and case studies on a wide range of areas, including: • 3D Deformation and Failure • In-situ Techniques and Microscale Effects on Mechanical Behavior • Vibration and Cyclic Fatigue • Integration of Models and Experiments • Interface-Mediated Damage and Failure • Fracture and Fatigue in Brittle Materials • Material Characterizations Using Thermography • Fatigue, Damage & Fracture Evaluation Using Infrared Thermography

Pathak, Pharindra [Auburn University]↗

Dynamic failure in two-phase materials

Previous experimental research has shown that microstructural features such as interfaces, inclusions, vacancies, and heterogeneities can all act as voidnucleation sites. However, it is not well understood how important these interfaces are to damage evolution and failure as a function of the surrounding parentmaterials. In this work, we present results on three different polycrystallinematerials: (1) Cu, (2) Cu-24 wt. %Ag, and (3) Cu-15 wt. %Nb which were studied to probe the influence of bi-metal interfaces onvoidnucleation and growth. These materials were chosen due to the range of difference in structure and bulk properties between the two phases. The initial results suggest that when there are significant differences between the bulk properties (for example: stacking fault energy, melting temperature, etc.) the type of interface between the two parent materials does not principally control the damage nucleation and growth process. Rather, it is the “weaker” material that dictates the dynamic spall strength of the overall two-phase material.

36 MATERIALS SCIENCE↗

Microstructure in the extreme environment: understanding and predicting dynamic damage processes

The future of materials science: strategic application for functionally controlled materials properties is emphasized by the need to control material performance in extreme environments. To this end, this study examines the separate effects of kinetics (in the form of dynamic loading rate and shock wave shape) from that of length-scale effects (in the form of microstructural defect distributions). Recently available mesoscale modeling techniques are being used to capture a physical link between kinetic and length-scale influences on dynamic loading. This work contributes innovative new tools in the form of shock-wave shaping techniques in dynamic experimentation, materials characterization, lending insight into 3D damage field analysis at micron resolution, and the physics necessary to provide predictive capabilities for dynamic damage evolution. Experimental results tailored for the discreet understanding of length-scale and kinetic effects during dynamic loading are obtained to provide the basis for the development of process-aware material performance models. The understanding of length-scale and kinetic effects in extreme environments of dynamic loading advances the understanding of current emerging issues relevant to phenomena such as inclusion related failure in metals, grain size dependence on ejecta, and benefits of interfaces in mitigating defect development specifically driven by the need to tailor material response. Finally, the coupling of experimental techniques with theory and simulation is aimed at advancing process-aware damage modeling as well as transitioning materials science from observation to property control.

36 MATERIALS SCIENCE↗

Model correction and updating of a stochastic degradation model for failure prognostics of miter gates

Understanding the degradation of the quoin block is vital for failure prognostics in miter gates. Due to the complicated degradation mechanism, degradation models based on simplifications and assumptions cannot accurately describe the damage evolution. It is observed that small errors in a simplified degradation model can lead to a large discrepancy in the remaining useful life estimation attributed to error accumulation over time. Aiming to address this issue in failure prognostics, this paper presents a dynamic model correction framework for a simplified degradation model using strain measurements. In the proposed framework, a polynomial chaos expansion (PCE) model is employed to compensate the missing physics in a simplified stochastic degradation model. Here, a maximum likelihood estimation method is developed to estimate the uncertain parameters of the simplified physics-based degradation model along with the unknown PCE model parameters using strain measurements as the observables. The updated damage degradation model is then applied to failure prognostics of a miter gate. Results of a case study show that the proposed approach can effectively improve the accuracy of failure prognostics in miter gates.

42 ENGINEERING↗

High Speed Impact Testing of UHMWPE Composite Using Orthogonal Arrays

Abstract Background Ultra high molecular weight polyethylene composites are fiber based composites used in armor applications. While some characterization has been conducted experimentally, this study varies multiple parameters simultaneously to investigate material response under a wide range of conditions. Objective This work focuses on characterizing the response of Dyneema ® HB26 hard laminate composites under high-speed impacts to examine the influence of plate diameter, clamping pressure, and plate spacing on target performance. Additionally, micro Computer Tomography scans are used to nondestructively evaluate the damage evolution in the targets. Methods These scan results are used in concert with more traditional armor performance metrics to evaluate the effect of various parameters using the method of orthogonal array analysis. This technique allows for multiple variables to be investigated in the same test series, saving time and budget while still providing quality results across a range of variables and variable values. Results We conclude that of the parameters investigated, the plate spacing parameter has the largest effect on performance, followed by the plate diameter. Bolt torque was found to not have a significant impact on results, indicating that an edge clamping pressure is not critical to material response. Additionally, by examining the high resolution scans, we can quantify the damage with an effective damage angle and that this angle is a good predictor of performance. Conclusion Finally a damage theory involving the effective bending strength of the plates is discussed as an explanation for all of the results observed in this test series.

Hannah, T. (ORCID:0000000230261362)↗

Effects of fabric architectures on mechanical and damage behaviors in carbon/epoxy woven composites under multiaxial stress states

The mechanical properties and damage evolutions of carbon/epoxy woven fabric composites with three different fabric architectures, including one plain weave and two twill weave patterns, are experimentally investigated under multiaxial stress states. In particular, the effects of weave patterns are investigated by monotonic and cyclic off-axis tension tests. Both elastic modulus and strength degrade remarkably with increasing off-axis loading angle, while Poisson's ratio is much higher than that measured from on-axis tests and increases with loading strain gradually. Different fabric architectures show limited effects on the modulus and strength under multiaxial stress states, and they are well predicted by transformation equation and Tsai-Wu failure criteria, respectively. However, significantly different failure behaviors are observed in three fabric composites, and microstructure observation shows that fabric architecture affects the stress concentration and the damage development. Smaller crimp ratio and compacted structure postpone the damage development but result in more abrupt failure under multiaxial stress states.

36 MATERIALS SCIENCE↗

Experimental data for damage mechanics simulation challenge

While there are many computational approaches for simulating damage in rock and other materials, few have been ground truth tested with either known experimental data or with blind data sets. Here, in this work, we present a bench-mark laboratory data set for a damage mechanics challenge to compare computational approaches on damage evolution in brittle-ductile materials. The samples were fabricated through additive manufacturing to produce repeatable specimens designed to fail in controlled ways. The failure was induced in the samples using a 3-point bending test to produce different Modes such as Mode I and mixed Modes including I-II, I-III and I-II-III Modes to generate a calibration data set and a blind challenge data set. Data collected included spatial and temporal measurements from traditional digital load–displacement sensors, 2D digital image correlation measurement to map surface deformations, 3D X-ray microscopy to ground-truth the crack-failure geometry, and laser profilometry to capture surface roughness. The data sets are available, on a data repository, to the community to advance computational models to improve our ability to predict damage in brittle-ductile materials.

3-point bending↗

Application of the Continuum Damage Mechanics Wilshire-Cano-Stewart (WCS) Model

In this study, the applications of the continuum damage mechanics-based Wilshire-Cano-Stewart (WCS) model are explored to predict rupture time, minimum-creep-strain-rate (MCSR), damage, damage evolution, and creep deformation. Increase knowledge in manufacturing methods has pushed the limit of material science and the development of new materials. Conventional testing is required to qualify materials against creep which according to the ASME B&PV III code, 10,000+ hours of experiments are necessary for each heat before materials are put into service. This process is costly and not feasible for new materials. As an alternative, models have been employed to predict creep behaviors and reduce the amount of time necessary for material qualification. Many models have been developed to predict distinct creep behaviors and the question of which model is best remains. Amongst current models, the WCS model has emerge with the ability to predict multiple behaviors using an explicit analytical approach with the ability to predict long-term creep. In this study the novel continuum damage mechanics WCS is employed in multiple applications. The goals of the study are (a) to discuss and determine the framework of the WCS model and validated it mathematically and using parametric simulations, (b) applied the model to accelerated creep data to show the capabilities of the model with non-conventional data, and (c) applied a novel numerical method, the datum temperature method (DTM) to show the model extrapolations and interpolations capabilities with limited and reduce data sets. To accomplish these goals, data is gathered for alloy P91 and Inconel 718 to develop and post-audit validate the model. The benefits of using the WCS model is that it provides an explicit stress and temperature dependency ideal for extrapolations, the coupled equations are suitable for finite element analysis (FEA) implementation, and it follows an explicit calibration approach. The model also proves that it can be applied to accelerated testing data and using the DTM.

Cano, Jaime A↗

The role of nickel in radiation damage of ferritic alloys

According to modern theory, damage evolution under neutron irradiation depends on the fraction of self-interstitial atoms (SIAs) produced in the form of one-dimensional glissile clusters. These clusters, having a low interaction cross-section with other defects, are absorbed mainly by grain boundaries and dislocations, creating the so-called production bias. It is known empirically that the addition of certain alloying elements influences many radiation effects, including swelling; however, the mechanisms are unknown in many cases. In this study, we report the results of an extensive multi-technique atomistic level modeling study of SIA clusters mobility in body-centered cubic Fe–Ni alloys. We have found that Ni interacts strongly with the periphery of clusters, affecting their mobility. The total effect is defined by the number of Ni atoms interacting with the cluster at the same time and can be significant, even in low-Ni alloys. Thus a 1 nm (37SIAs) cluster is practically immobile at T < 500 K in the Fe–0.8 at.% Ni alloy. Increasing cluster size and Ni content enhances cluster immobilization. Finally, this effect should have quite broad consequences in void swelling, matrix damage accumulation and radiation induced hardening and the results obtained help to better understand and predict the effects of radiation in Fe–Ni ferritic alloys.

36 MATERIALS SCIENCE↗

A dislocation-based crystal plasticity framework for dynamic ductile failure of single crystals

We developed a framework for dislocation-based viscoplasticity and dynamic ductile failure to model high strain rate deformation and damage in single crystals. The rate-dependence of the crystal plasticity formulation is based on the physics of relativistic dislocation kinetics suited for extremely high strain rates. The damage evolution is based on the dynamics of void growth, which are governed by both micro-inertia as well as dislocation kinetics and dislocation substructure evolution. Furthermore, an averaging scheme is proposed in order to approximate the evolution of the dislocation substructure in both the macroscale as well as its spatial distribution at the microscale. In addition, a concept of a single equivalent dislocation density that effectively captures the collective influence of dislocation density on all active slip systems is proposed here. Together, these concepts and approximations enable the use of semi-analytic solutions for void growth dynamics developed in [J. Wilkerson and K. Ramesh. A dynamic void growth model governed by dislocation kinetics. J. Mech. Phys. Solids, 70:262–280, 2014.], which greatly reduce the computational overhead that would otherwise be required. The resulting homogenized framework has been implemented into a commercially available finite element package, and a validation study against a suite of direct numerical simulations was carried out.

36 MATERIALS SCIENCE↗

Development of Surface Grain Relief on Self-Ion Irradiated Copper

The development of surface grain relief has been observed on self-ion irradiated pure polycrystalline copper. However, the mechanistic origin of this feature has yet to be determined. Two possible mechanisms, anisotropic creep relaxation of void swelling induced stresses and crystallographic orientation-dependent sputtering rate differences, are being investigated as the cause of this evolution. This work focuses on characterizing the surface development and investigating the mechanism of orientation-dependent sputtering. Based on the conditions under which these specimens were irradiated, preferential sputtering is not likely to be the cause of the observed grain relief. Surface grain relief can greatly influence the ability to non-destructively detect irradiation-induced effects in polycrystalline metals. Determining the origin of grain relief development is necessary before this surface feature can be used an indicator of irradiation-induced effects in pure copper and other alloys. The development of surface grain relief has been observed on self-ion irradiated pure polycrystalline copper irradiated to 100 dpa. This surface feature was first noted by measuring samples using transient grating spectroscopy and later confirmed using scanning electron microscopy. Calculations of single-crystal sputtering rates show that the difference in sputtering yields between a randomly-oriented solid and a low-index plane is not sufficient to account for the observed height difference. SEM images appear to show a maximum step-height difference of around 100 nm and differential sputtering can only account for differences on the order of 10 nm at most. This determination indicates that anisotropic creep relaxation may be the mechanistic origin of the observed surface features. If this is the case, which will be confirmed by future work, then TG spectroscopy may be an effective tool for the determination of the onset of certain radiation-damage evolution. For example, if the onset of creep relaxation is strongly correlated to a specific level of void swelling and if the surface features present as a result of creep relaxation can be observed using TG spectroscopy, then accurate determinations of particular levels of void swelling may be made. (authors)

36 MATERIALS SCIENCE↗

Kinetic Monte Carlo simulations of aging in δ -Pu

We have developed a first-passage kinetic Monte Carlo approach for materials aging to investigate the sensitivity of void swelling to model parameters, including helium bubble density and size distribution. In addition to explicitly accounting for the spatial distribution of individual point defects, bubbles, and voids, our approach can simulate total doses equivalent to 100 years of natural aging on statistically representative volumes of materials. This technique enables us to study the effects on swelling and radiation damage evolution due to temperature and dose rate (as altered in artificially aged experiments), differences in effective interaction radii between vacancies and interstitials, and varying defect diffusion activation energies, while providing more detailed information than previous rate-equation based approaches. In conclusion, our results indicate that spatial effects that are not modeled in mean-field rate theories could play a significant role in void swelling initiation and growth for certain regimes of model parameters.

Actinides↗

Gas Transport in the Insensitive High Explosive PBX 9502

Small-scale laboratory experiments were performed to analyze gas transport mechanics in PBX 9502, an insensitive high explosive (IHE) composition. Two independent investigations are reported here. First, gas permeametry and dynamic pycnometry techniques were used to measure the molecular flow (Knudsen) coefficient and the internally interconnected void fraction of pristine and thermally damaged samples in two uniaxial pressing orientations. The permeability of PBX 9502 was found to be unmeasurably low (of the same order of magnitude as PTFE) with gas transport being diffusion-dominated. Secondly, a pressure vessel experiment was developed to measure quasi-static and dynamic gas generation as the explosive was heated to self-ignition (cookoff). The gas generation results and the permeability/diffusivity findings provide evidence that PBX 9502 remains impermeable until seconds prior to self-ignition. At ignition, internal void-pressure drives macro-scale cracking and the sample becomes uniformly incorporated in the following deconsolidating deflagration. These results are discussed within the context of previous observations of pressure-dependent cookoff behavior of PBX 9502 and provide a more complete description of thermal damage evolution in this explosive composition.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Parameter Calibration of GTN Damage Model and Formability Analysis of 22MnB5 in Hot Forming Process

Hot forming of high strength steel at elevated temperatures is an attractive technology to achieve the lightweight of vehicle body. The mechanical behavior of boron steel 22MnB5 strongly depends on the variation of temperature which makes the process design more difficult. In this paper, the Gurson–Tvergaard–Needleman (GTN) model is used to study the formability of 22MnB5 sheet at different temperatures. Firstly, the rheological behavior of 22MnB5 is analyzed through a series of hot tensile tests at a temperature range of 600-800 °C. Then, a detailed process to calibrate the damage parameters is given based on the response surface methodology and genetic algorithm method. The GTN model together with the damage parameters calibrated is then implemented to simulate the deformation and damage evolution of 22MnB5 in the process of high-temperature Nakazima test. The capability of the GTN model as a suitable tool to evaluate the sheet formability is confirmed by comparing experimental and calculated results. Finally, as a practical application, the forming limit diagram of 22MnB5 at 700 °C is constructed using the Nakazima simulation and Marciniak–Kuczynski (M–K) model, respectively. And the simulation integrated GTN model shows a higher reliability by comparing the predicted results of these two approaches with the experimental ones.

36 MATERIALS SCIENCE↗