Search NASA⌕ Search

SEARCH · Search NASA

Results for “data base for model validation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

A study on computational fluid dynamics modeling of a refrigerated container for COVID-19 vaccine distribution with experimental validation

A key issue with the distribution of vaccines to prevent COVID-19 is the temperature level required during transport, storage, and distribution. Typical refrigerated transport containers can provide a temperature-controlled environment down to -30 °C. However, the Pfizer vaccine must be carefully transported and stored under a lower temperature between -80 °C and -60 °C. One way to provide the required temperature is to pack the vaccine vials into small packages containing dry ice. Dry ice sublimates from a solid to a gas, which limits the allowable transport duration. This can be mitigated by transporting in a -30 °C refrigerated container. Moreover, because the dry ice will sublimate and thereby release CO 2 gas into the transport container, monitoring the CO 2 concentration within the refrigerated container is also essential. In the present work, a 3D computational fluid dynamics model was developed based on a commercially available refrigerated container and validated with experimental data. The airflow, temperature distribution, and CO 2 concentration within the container were obtained from the simulations. The modeling results can provide guidance on preparing experimental setups, thus saving time and lowering cost, and also provide insight into safety precautions needed to avoid hazardous conditions associated with the release of CO 2 during vaccine distribution.

59 BASIC BIOLOGICAL SCIENCES↗

Model-based calculations of off-axis ratio of conic beams for a dedicated 6 MV radiosurgery unit

Purpose: Because the small-radius photon beams shaped by cones in stereotactic radiosurgery (SRS) lack lateral electronic equilibrium and a detector's finite cross section, direct experimental measurement of dosimetric data for these beams can be subject to large uncertainties. As the dose calculation accuracy of a treatment planning system largely depends on how well the dosimetric data are measured during the machine's commissioning, there is a critical need for an independent method to validate measured results. Therefore, the authors studied the model-based calculation as an approach to validate measured off-axis ratios (OARs). Methods: The authors previously used a two-component analytical model to calculate central axis dose and associated dosimetric data (e.g., scatter factors and tissue-maximum ratio) in a water phantom and found excellent agreement between the calculated and the measured central axis doses for small 6 MV SRS conic beams. The model was based on that of Nizin and Mooij [''An approximation of central-axis absorbed dose in narrow photon beams,'' Med. Phys. 24, 1775-1780 (1997)] but was extended to account for apparent attenuation, spectral differences between broad and narrow beams, and the need for stricter scatter dose calculations for clinical beams. In this study, the authors applied Clarkson integration to this model to calculate OARs for conic beams. OARs were calculated for selected cones with radii from 0.2 to 1.0 cm. To allow comparisons, the authors also directly measured OARs using stereotactic diode (SFD), microchamber, and film dosimetry techniques. The calculated results were machine-specific and independent of direct measurement data for these beams. Results: For these conic beams, the calculated OARs were in excellent agreement with the data measured using an SFD. The discrepancies in radii and in 80%-20% penumbra were within 0.01 cm, respectively. Using SFD-measured OARs as the reference data, the authors found that the calculated OARs were more accurate than those measured with a microchamber or film dosimetry. Conclusions: The model produces sufficiently accurate conic beam dosimetric data that can be used to validate direct measurement results for such beams.

60 APPLIED LIFE SCIENCES↗

Issues and approach to develop validated analysis tools for hypersonic flows: One perspective

Critical issues concerning the modeling of low-density hypervelocity flows where thermochemical nonequilibrium effects are pronounced are discussed. Emphasis is on the development of validated analysis tools. A description of the activity in the Ames Research Center's Aerothermodynamics Branch is also given. Inherent in the process is a strong synergism between ground test and real-gas computational fluid dynamics (CFD). Approaches to develop and/or enhance phenomenological models and incorporate them into computational flow-field simulation codes are discussed. These models have been partially validated with experimental data for flows where the gas temperature is raised (compressive flows). Expanding flows, where temperatures drop, however, exhibit somewhat different behavior. Experimental data for these expanding flow conditions are sparse; reliance must be made on intuition and guidance from computational chemistry to model transport processes under these conditions. Ground-based experimental studies used to provide necessary data for model development and validation are described. Included are the performance characteristics of high-enthalpy flow facilities, such as shock tubes and ballistic ranges.

Deiwert, George S.↗

Issues and approach to develop validated analysis tools for hypersonic flows: One perspective

Critical issues concerning the modeling of low density hypervelocity flows where thermochemical nonequilibrium effects are pronounced are discussed. Emphasis is on the development of validated analysis tools, and the activity in the NASA Ames Research Center's Aerothermodynamics Branch is described. Inherent in the process is a strong synergism between ground test and real gas computational fluid dynamics (CFD). Approaches to develop and/or enhance phenomenological models and incorporate them into computational flowfield simulation codes are discussed. These models were partially validated with experimental data for flows where the gas temperature is raised (compressive flows). Expanding flows, where temperatures drop, however, exhibit somewhat different behavior. Experimental data for these expanding flow conditions is sparse and reliance must be made on intuition and guidance from computational chemistry to model transport processes under these conditions. Ground based experimental studies used to provide necessary data for model development and validation are described. Included are the performance characteristics of high enthalpy flow facilities, such as shock tubes and ballistic ranges.

Deiwert, George S.↗

Assessment and Applications of NASA Ozone Data Products Derived from Aura OMI-MLS Satellite Measurements in Context of the GMI Chemical Transport Model

Measurements from the Ozone Monitoring Instrument (OMI) and Microwave Limb Sounder (MLS), both onboard the Aura spacecraft, have been used to produce daily global maps of column and profile ozone since August 2004. Here we compare and evaluate three strategies to obtain daily maps of tropospheric and stratospheric ozone from OMI and MLS measurements: trajectory mapping, direct profile retrieval, and data assimilation. Evaluation is based upon an assessment that includes validation using ozonesondes and comparisons with the Global Modeling Initiative (GMI) chemical transport model (CTM). We investigate applications of the three ozone data products from near-decadal and inter-annual timescales to day-to-day case studies. Zonally averaged inter-annual changes in tropospheric ozone from all of the products in any latitude range are of the order 1-2 Dobson Units while changes (increases) over the 8-year Aura record investigated http://eospso.gsfc.nasa.gov/atbd-category/49 vary approximately 2-4 Dobson Units. It is demonstrated that all of the ozone products can measure and monitor exceptional tropospheric ozone events including major forest fire and pollution transport events. Stratospheric ozone during the Aura record has several anomalous inter-annual events including stratospheric warming split events in the Northern Hemisphere extra-tropics that are well captured using the data assimilation ozone profile product. Data assimilation with continuous daily global coverage and vertical ozone profile information is the best of the three strategies at generating a global tropospheric and stratospheric ozone product for science applications.

GMI↗

Performance evaluation of a wrapped around condenser for heat pump water heater applications

In this report, accurate performance evaluation of a wrapped-around condenser for heat pump water heaters (WHPWH) is critical since the COP of the system depends heavily on thermal stratification and condenser design. An analytical, quasi-steady state heat balance method has been developed to determine the optimal spacing between adjacent channels, tube diameter, tube shape, and total refrigerant charge amount for the condenser. The heat transfer rate is compared among three approaches: the refrigerant thermodynamic model, the condenser-wrap fin model, and the analytical natural convection model on the inside of the tank for the three regions based on the refrigerant phase (e.g., super-heated, saturated, or subcooled). The heat transfer rate was predicted by a combination of slug-plug and annular flow for a D-shaped helical tube. Experimental data were used as boundary conditions for validating the model. The rate of heat transfer based on tube shape and tank wall temperatures was compared by CFD analysis. Parametric analysis indicates a tradeoff between refrigerant mass, pressure drop, tube diameter, and tube length to maximize the heat transfer rate. The model suggests the saturated region length can be extended by 400%, and the condenser pressure drop can be reduced by 23% with an optimal spacing pattern.

42 ENGINEERING↗

Neural Network Atmospheric Correction of Remote Sensing Imagery Over Water Using a Synthetic Dataset

Remote sensing atmospheric correction methods have primarily focused on imagery over land. However, accurate correction over water is important for monitoring and research of aquatic environments. More research in this area is ongoing, though one of the biggest challenges is enough quality data to develop and validate correction methods. This is especially true for neural network (NN) -based models which have shown promise in this area given enough quality data. To address this deficiency of data, we are leveraging a synthetic dataset produced by a model called SWIPE that uses radiative transfer modeling to simulate the atmospheric effects on water-leaving (WL) reflectance to estimate top-of-atmosphere (TOA) reflectance. This allows us to produce almost unlimited pairs of WL reflectance and corresponding TOA reflectance for model training across a variety of atmospheric conditions. We use two approaches for our atmospheric correction model. One uses a conditional variational autoencoder (VAE) to estimate a single WL reflectance value from a single TOA reflectance value. The second is based on a UNET architecture and estimates an array of WL reflectance values from an array of TOA reflectance values. The goal of the second method is to capture atmospheric effects that occur spatially between values within the array as compared to the first method.

deep learning↗

Prediction of Cooling Curves for Controlled Unidirectional Solidification Under the Influence of Shrinkage: A Semi-analytical Approach

Quality of casting products can be significantly improved by controlling the crystal growth rate. Both dendritic and equiaxed grain structures depend strongly on crystal growth rate along the crystallographic direction. Uncontrolled solidification processes may lead to the formation of porous and columnar material with an extremely non-homogeneous composition distribution. These undesirable micro-structures can be avoided by adopting an optimal cooling rate (K/s) during the crystal growth. The present work focuses on determining suitable cooling curves to obtain desired unidirectional crystal growth rates, by implementing a semi-analytical model. Here, we defined cooling curve as the time history of temperature evolution at the cold boundary. The proposed semi-analytical heat transfer model is diffusion driven and accounts for shrinkage effect during solidification. The proposed model is found capable of predicting cooling curves for prescribed interface velocities. The model is self-sufficient in validating itself by means of solving inverse and forward problems. The cooling curve prediction by the model is validated by using it as the transient boundary condition for an existing enthalpy updating scheme-based numerical model. The proposed model is also applied to empirical data reported in literature, to validate the model against experimental results. All the validations showcased excellent fit. The proposed model will facilitate controlled unidirectional crystal growth rate by providing cooling rate (K/s) as an input for the experiments involving directional solidification.

36 MATERIALS SCIENCE↗

Predeployment progress of the Canister Deposition Field Demonstration

This report updates the high-level test plan for evaluating surface deposition on three commercial 32PTH2 spent nuclear fuel (SNF) canisters inside NUTECH Horizontal Modular Storage (NUHOMS) Advanced Horizontal Storage Modules (AHSMs) from Orano (formerly Transnuclear Inc.) and provides a summary of the surface sampling activities that have been conducted to date. The details contained in this report represent the best designs and approaches explored for testing as of this publication. Given the rapidly developing nature of this test program, some of these plans may change to accommodate new objectives or requirements. One goal of this testing is to collect defensible and detailed dust deposition measurements from the surface of dry storage canisters in a marine coastal environment to guide chloride-induced stress corrosion cracking (CISCC) research. Another goal is to provide data for the validation of computational fluid dynamics (CFD) based deposition modeling. To facilitate surface sampling, the otherwise highly prototypic dry storage systems will not contain SNF but rather will be electrically heated to mimic the decay heat and thermal hydraulic environment. Test and heater design is supported by detailed CFD modeling. Instrumentation throughout the canister, storage module, and environment will provide extensive information about the thermal-hydraulic behavior of horizontal dry cask storage systems. Manual sampling over a comprehensive portion of the canister surface at regular time intervals will offer detailed quantification and composition of the deposited particulates from a realistic storage environment. Discussions of a potential host site for the Canister Deposition Field Demonstration (CDFD) are ongoing. Until a host site is chosen, testing of key CDFD hardware components including the heater assemblies, power skid, and remote data acquisition system will continue. Functional testing of the finalized heater assemblies and test apparatus started this fiscal year. These initial heater tests have shown the assemblies are performing within design specifications. Staged surface sampling of a mockup of a canister outside the AHSM on a transfer skid was also performed. Refinements to the sampling procedures and techniques were captured from observation of these activities and lessons-learned debriefs. These updated sampling procedures and techniques are planned to be tested again in the field using the mockup in order to assure personnel are using the most accurate and repeatable methods possible prior to deployment for actual CDFD testing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Application of NCRP 156 Wound Models for the Analysis of Bioassay Data from Plutonium Contaminated Wound Cases

The NCRP 156 wound model was heavily based on data from animal experiments. The authors of the report acknowledged this limitation and encouraged validation of the models using data from human wound exposures. The objective of this paper was to apply the NCRP 156 wound models to the bioassay data from four plutonium-contaminated wound cases reported in the literature. Because a wide variety of forms of plutonium can be expected at a nuclear facility, a combination of the wound models—rather than a single model—was used to successfully explain both the urinary excretion data and wound retention data in three cases. The data for the fourth case could not be explained by any combination of the default wound models. While this may possibly be attributed to the existence of a category of plutonium whose solubility and chemistry are different than those described by the NCRP 156 default categories, the differences may also be the result of differences in systemic biokinetics. Lastly, the concept of using a combination of biokinetic models may be extended to inhalation exposures as well, where more than one form of radionuclide—particles of different solubility or different sizes—may exist in a workplace.

60 APPLIED LIFE SCIENCES↗

Predicting departure from nucleate boiling with advanced data- and physics-driven approaches

The subcooled and low-quality saturated flow boiling critical heat flux (CHF) corresponding to the departure from nucleate boiling (DNB) is one of the major limiting factors in the design and operation of pressurized water reactors (PWRs). Due to lack of agreement on its physical mechanisms, development of an accurate DNB-type CHF model has been elusive. The various steady-state (SS) predictive tools that have been proposed can be grouped into two categories: (1) data-driven methods—namely best-fit empirical correlations and look-up tables that result in relatively good agreement with specific experimental datasets but often fail to extend beyond their ranges of validity, and (2) the physics-based mechanistic models that rely on reasonable yet limited understanding of the underlying physics and apply constitutive relations to close the conservation equations. On one hand, with recent advances in computational capabilities and optimization techniques, machine learning (ML)-based methods constitute an alternative and a more advanced, data-driven approach. With enough data, they can be particularly useful in engineering fields where the physical phenomena are complex and challenging to model. On the other hand, a state-of-the-art physics-driven approach would not only provide more accurate prediction of SS CHF, but it would also help better understand and model transient applications. The data-driven regression models use deep feed-forward neural networks (NNs) and random forests to cross-validate with 1,865 CHF test cases, covering a wide range of flow conditions and channel geometries. The best-estimate ML-based predictors compare favorably with the widely used look-up table for annulus and plate, and sensitivity analysis has confirmed their effectiveness. The key advantage of ML-based methods is their online extensibility of applicability domain. The proposed physics-driven approach combines key assumptions and parameters in the relatively well-accepted theories of liquid sublayer dryout and near-wall bubble crowding. A more realistic understanding of local mechanisms has been modeled. The new model has been optimized and validated against 1,439 tube data, and it shows considerably improved performance when compared to a recent mechanistic model, demonstrating unbiased close agreement with measurements over a wide range of operating conditions. Future work will extend the improved physics-driven model to non-tube geometry applications and will couple the model with ML via a hybrid approach. The mechanistic SS work will also serve to improve understanding and to model transient CHF scenarios.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NREL Evaluates Performance of Hydraulic Hybrid Refuse Vehicles

This highlight describes NREL's evaluation of the in-service performance of 10 next-generation hydraulic hybrid refuse vehicles (HHVs), 8 previous-generation (model year 2013) HHVs, and 8 comparable conventional diesel vehicles operated by Miami-Dade County's Public Works and Waste Management Department in southern Florida. Launched in March 2015, the on-road portion of this 12-month evaluation focuses on collecting and analyzing vehicle performance data - fuel economy, maintenance costs, and drive cycles - from the HHVs and the conventional diesel vehicles. The fuel economy of heavy-duty vehicles, such as refuse trucks, is largely dependent on the load carried and the drive cycles on which they operate. In the right applications, HHVs offer a potential fuel-cost advantage over their conventional counterparts. This advantage is contingent, however, on driving behavior and drive cycles with high kinetic intensity that take advantage of regenerative braking. NREL's evaluation will assess the performance of this technology in commercial operation and help Miami-Dade County determine the ideal routes for maximizing the fuel-saving potential of its HHVs. Based on the field data, NREL will develop a validated vehicle model using the Future Automotive Systems Technology Simulator, also known as FASTSim, to study the impacts of route selection and other vehicle parameters. NREL is also analyzing fueling and maintenance data to support total-cost-of-ownership estimations and forecasts. The study aims to improve understanding of the overall usage and effectiveness of HHVs in refuse operation compared to similar conventional vehicles and to provide unbiased technical information to interested stakeholders.

33 ADVANCED PROPULSION SYSTEMS↗

Study of Thermomechanical Behavior of Zirconium-0.3 Tin Alloy

Zirconium-based alloys are used in the manufacturing of nuclear fuel tubes. These tubes need to be clad with zirconium-tin (Zr-0.3 wt.% Sn) alloy to enhance the lives of tubes. Manufacturing of such clad tubes is a challenging task, due to work hardening and dynamic softening phenomenon. In this study, hot deformation behavior of Zr-0.3Sn alloy is investigated at different temperatures and strain rates. It is found that fully recrystallized microstructure can be obtained by working at around 900 °C and high strain rate of 10 s{sup −1}. Further, constitutive equations are developed for the entire domain of deformation range and fitted into standard FEM-based simulation model for extrusion. The simulation results are validated with experimental data. The difference in flow stresses values obtained from numerical and experimental methods was around 14%.

36 MATERIALS SCIENCE↗

Wood Decomposition: Understanding Processes Regulating Carbon Transfer to Soil Carbon Pools Using FACE Wood at Multiple Scales

Dead wood comprises approximately 20% of forest biomass. While it is widely recognized for its role in ecosystem functions relative to habitat and nutrient cycling, there are considerable uncertainties associated with its role in the forest carbon (C) cycle. The principal uncertainty is whether dead wood contributes to the soil C pool. With little supporting evidence, the presumption is that C in wood is respired back to the atmosphere through decomposition processes. The inability to attribute forest soil C to its source components has been a barrier to addressing this important forest carbon cycle question. The U.S. Dept. of Energy’s Free Air CO 2 Enrichment (FACE) experiment produced wood that has a distinct δ 13 C signature that can be used to trace its fate through organic matter decomposition processes. Using two hardwood species (aspen, birch) from the Rhinelander FACE site and pine from the Duke FACE site, the FACE Wood Decomposition Experiment (FWDE) was established in 2011 to provide the foundation for addressing wood decomposition and its associated processes at the continental scale. Plots were installed on nine experimental forests representing a range in bioclimatic forest conditions within the continental U.S. Each identical plot has logs of the three species incubating on the soil surface and pine logs suspended in the air, representing standing dead wood. Abiotic conditions are monitored continuously, and soil and forest conditions characterized. Logs on the sites have been measured every two years to assess decay. This project was initiated in 2016 with specific objectives to: (a) determine whether dead wood C contributes to the soil C pool, (b) assess the fungal community composition mediating the decay, (c) assess the interactions of termites with microbial decay, and (d) develop a mechanistic model to simulate wood decomposition. The principal field sampling was conducted in 2017; correspondingly, the results reported here represent six years of decomposition. Wood decomposition varied from 13 to 75 % loss across the bioclimatic gradient. Sites in the southeastern U.S. coastal plain and piedmont had fastest decomposition rates for each of the species. In contrast sites in the Rocky Mountains had the slowest decay rates, which were associated with cold temperatures. Standing deadwood decomposes at a much slower rate than logs on the soil surface; a response due to differences in wood moisture content. Wood carbon was measured in the mineral soil across each of the sites; accordingly, this is the first study to affirm that a portion of the wood C does become part of the soil C pool. Averaged across the FWDE sites, approximately 1.4% of the soil C in the upper 10 cm of the mineral soil directly beneath the log was derived from the deadwood; within 50 cm of the log, wood C accounted for an average of 2.1%. These results demonstrate that the contribution of deadwood to the soil C pool is a soil volume surrounding the log; and it’s likely a larger volume than what we sampled. We also hypothesized that there would be more wood C in the mineral soil when termites were present. However, that hypothesis wasn’t supported by measurements on the Santee Experimental Forest termite exclusion (SEF-TX) plots under FACE logs that incubated for 6 years. Across all the sites, the majority of the wood C was transferred to the atmosphere. Approximately 7,000 fungal species were sequenced. The fungal communities were different among each of the sites suggesting local colonization; interestingly, within sites the three species also exhibited differences in fungal community composition. White rot was the dominant fungal form in pine and hardwood, which yields less lignin in the wood residue. Brown rot occurred in approximately 20% of the pine and aspen logs, and it did not occur in birch logs. The occurrence of brown rot was only weakly correlated to site factors. We conducted two additional experiments to assess the effects of termites on wood decomposition and the associated interactions with the fungal community. Pine and birch logs were incubated on the Santee Experimental Forest termite exclusion plots in upland and riparian settings. There was no difference in decay between areas where termites were able colonize and plots where they had been excluded. Highly variable foraging by termites was a primary contributor the result. Correspondingly, fungal communities did not vary on logs incubated among the two treatments, but they did reflect site and species differences. The second experiment was conducted on each of the nine FWDE sites where pine and birch wood blocks were incubated for two years with and without a wrapping designed to exclude termites and other arthropods. The effects of termites on wood decomposition could be confirmed on two of the four sites known to have subterranean termites. On the two southeastern sites, termites contributed approximately 8% to mass loss in pine blocks over two years. A major factor clouding the role of termites in wood decomposition is the inability to assess the time, duration, and intensity of the foraging with the logs. Another uncertainty is related to whether a piece of wood will be foraged. A process-based wood decomposition model was developed representing biological processes mediated by fungi, bacteria, termites, beetles, as well as physical and chemical processes. The Coarse Wood Decomposition Model (CWDM) was parameterized based on a thorough review of the literature and it was validated using data from the FWDE. In the initial setup, the model considers softwoods and hardwoods groups, as opposed to individual species. Sensitivity analyses incorporating climate data from 89 locations in North America demonstrated that CWDM was stable from the tropics to the boreal zone. Model calibration and validation showed it to perform very well. The CWDM is poised for additional testing with subsequent FWDE data as well as other data sets, and it is available for incorporation into forest biogeochemical models or DOEs Earth System Modeling framework.

54 ENVIRONMENTAL SCIENCES↗

SU-F-T-156: Monte Carlo Simulation Using TOPAS for Synchrotron Based Proton Discrete Spot Scanning System

Purpose: This study provides an overview of the design and commissioning of the Monte Carlo (MC) model of the spot-scanning proton therapy nozzle and its implementation for the patient plan simulation. Methods: The Hitachi PROBEAT V scanning nozzle was simulated based on vendor specifications using the TOPAS extension of Geant4 code. FLUKA MC simulation was also utilized to provide supporting data for the main simulation. Validation of the MC model was performed using vendor provided data and measurements collected during acceptance/commissioning of the proton therapy machine. Actual patient plans using CT based treatment geometry were simulated and compared to the dose distributions produced by the treatment planning system (Varian Eclipse 13.6), and patient quality assurance measurements. In-house MATLAB scripts are used for converting DICOM data into TOPAS input files. Results: Comparison analysis of integrated depth doses (IDDs), therapeutic ranges (R90), and spot shape/sizes at different distances from the isocenter, indicate good agreement between MC and measurements. R90 agreement is within 0.15 mm across all energy tunes. IDDs and spot shapes/sizes differences are within statistical error of simulation (less than 1.5%). The MC simulated data, validated with physical measurements, were used for the commissioning of the treatment planning system. Patient geometry simulations were conducted based on the Eclipse produced DICOM plans. Conclusion: The treatment nozzle and standard option beam model were implemented in the TOPAS framework to simulate a highly conformal discrete spot-scanning proton beam system.

60 APPLIED LIFE SCIENCES↗

On the Directional Dependence and Null Space Freedom in Uncertainty Bound Identification

In previous work, the determination of uncertainty models via minimum norm model validation is based on a single set of input and output measurement data. Since uncertainty bounds at each frequency is directionally dependent for multivariable systems, this will lead to optimistic uncertainty levels. In addition, the design freedom in the uncertainty model has not been utilized to further reduce uncertainty levels. The above issues are addressed by formulating a min- max problem. An analytical solution to the min-max problem is given to within a generalized eigenvalue problem, thus avoiding a direct numerical approach. This result will lead to less conservative and more realistic uncertainty models for use in robust control.

Lim, K. B.↗

Empirical Validation of Building Energy Modeling using Flexible Research Platform

Recently, efforts have been made to provide reliable empirical data for ANSI/ASHRAE Standard 140, Standard Method of Test for the Evaluation of Building Energy Analysis Computer Programs, to enable improved accuracy of building energy model (BEM) engines and improved characterization of their accuracy. The motivation for this effort is that the use of reliable empirical validation data sets in the evaluation of building energy modeling tools will lead to more consistent and validated simulation engines across all software vendors. This would expedite the use of building energy modeling in designing new buildings and retrofitting existing buildings, which delivers more energy efficient buildings.As part of a three-year multi-lab empirical validation project sponsored by U.S. DOE, this research project generated cooling season test plans by reviewing ASHRAE Standard 140, and the tests were performed based on the test plan. Finally, the experimental data sets were compared with the EnergyPlus model to demonstrate the validation procedure.

Im, Piljae↗

Serial Network Flow Monitor

Using a commercial software CD and minimal up-mass, SNFM monitors the Payload local area network (LAN) to analyze and troubleshoot LAN data traffic. Validating LAN traffic models may allow for faster and more reliable computer networks to sustain systems and science on future space missions. Research Summary: This experiment studies the function of the computer network onboard the ISS. On-orbit packet statistics are captured and used to validate ground based medium rate data link models and enhance the way that the local area network (LAN) is monitored. This information will allow monitoring and improvement in the data transfer capabilities of on-orbit computer networks. The Serial Network Flow Monitor (SNFM) experiment attempts to characterize the network equivalent of traffic jams on board ISS. The SNFM team is able to specifically target historical problem areas including the SAMS (Space Acceleration Measurement System) communication issues, data transmissions from the ISS to the ground teams, and multiple users on the network at the same time. By looking at how various users interact with each other on the network, conflicts can be identified and work can begin on solutions. SNFM is comprised of a commercial off the shelf software package that monitors packet traffic through the payload Ethernet LANs (local area networks) on board ISS.

Robinson, Julie A.↗