Search NASA⌕ Search

SEARCH · Search NASA

Results for “detachment control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

A Mechanistic Study of Nucleate Boiling Heat Transfer Under Microgravity Conditions

Experimental studies of growth and detachment processes of a single bubble and multiple bubbles formed on a heated surface have been conducted in the parabola flights of KC-135 aircraft. Distilled water and PF5060 were used as the test liquids. A micro-fabricated test surface was designed and built. Artificial cavities of diameters 10 microns, 7 microns and 4 microns were made on a thin polished Silicon wafer that was electrically heated by a number of small heating elements on the back side in order to control the surface superheat. Bubble growth period, bubble size and shape from nucleation to departure were measured under subcooled and saturation conditions. Significantly larger bubble departure diameters and bubble growth periods than those at earth normal gravity were observed. Bubble departure diameters as large as 20 mm for water and 6 mm for PF5060 were observed as opposed to about 3 mm for water and less than 1 mm for PF5060 at earth normal gravity respectively. It is found that the bubble departure diameter can be approximately related to the gravity level through the relation D(sub d) proportional 1/g(exp 1/2). For water,the effect of wall superheat and liquid subcooling on bubble departure diameter is found to be small.The growth periods are found to be very sensitive to liquid subcooling at a given wall superheat. However,the preliminary results of single bubble dynamics using PF5060 showed that the departure diameter increases when wall superheat is elevated at the same gravity and subcooling. Growth period of single bubbles in water has been found to vary as t(sub g) proportional g(exp -.93). For water, when the magnitude of horizontal gravitational components was comparable to that of gravity normal to the surface, single bubbles slid along the heater surface and departed with smaller diameter at the same gravity level in the direction normal to the surface. For PF5060, even a very small horizontal gravitational component caused the sliding of bubble along the surface. The numerical simulation has been carried out by solving under the condition of axisymmetry, the mass, momentum, and energy equations for the vapor and the liquid phases. In the model the contribution of micro-layer has been included and instantaneous shape of the evolving vapor-liquid interface is determined from the analysis. Consistent with the experimental results, it is found that effect of reduced gravity is to stretch the growth period and bubble diameter It is found that effect of reduced gravity is to stretch the growth period and bubble diameter at departure. The numerical simulations are in good agreement with the experimental data for both the departure diameters and the growth periods. In the study on dynamics of multiple bubbles, horizontal merger of 2,3 4,and 5 bubbles was observed. It is found that after merger of 2 and 3 bubbles the equivalent diameter of the detached bubble is smaller than that of a single bubble departing at the same gravity level. During and after bubble merger, liquid still fills the space between the vapor stems so as to form mushroom type bubbles. The experimental and numerical studies conducted so far have brought us a step closer to prediction of nucleate boiling heat fluxes under low gravity conditions. Preparations for a space flight are continuing.

Dhir, V. K.↗
NASA NTRS1982

An experimental investigation of circulation control flow fields using holographic interferometry

Experiments are presented which were conducted on flow fields produced by a circulation control airfoil utilizing the Coanda effect at the trailing edge. The application of holographic interferometry to obtain both visualization and quantitative data on the flow field about a circulation control airfoil at transonic flow speed is covered. A brief description of the flow model and measurement techniques is given. The data reduction procedure, results, and interpretation are presented. The results have provided a good deal of information on the character of the flow field, particularly in the neighborhood of the trailing edge. As to the airfoil design, it is apparent that improved performance can be achieved if jet detachment is delayed. Another design improvement would involve the development of an optimum trailing-edge shape for the expected operating Mach and Reynolds number ranges.

Bachalo, William D.↗
NASA NTRS1994

Escarpment evolution on high-elevation rifted margins: Insights derived from a surface processes model that combines diffusion, advection and reaction

Experiments with a surface processes model of large-scale (1-1000 km) long-term (1-100 m.y.) erosional denudation are used to establish the controls on the evolution of a model escarpment that is related to the rifting of a continent. The mdoel describes changes in topographic form as a result of sumultaneous short- and long-range mass transport representing hillslope (diffusive) processes and fluvial transport (advection), repsectively. Fluvial entrainment is modeled as a first-order kinetic reaction which reflects the erodibility of the substrate, and therefore the fluvial system is not necessarily carrying at capacity. One dimensional and planform models demonstrate that the principal controls on the evolution of an initially steep model escarpment are (1) antecedent topography/drainage; (2) the timesale (or equivalently a length scale) in the fluvial entrainment reaction; (3) the flexural response of the lithosphere to denudation; and (4) the relative efficiencies of the short- and long-range transport processes. When rainfall and substrate lithology are uniform, a significant amount of discharge draining over the escarpment top causes it to degrade. Only when the top of the model escarpment coincides with a drainage divide can escarpment retreat occur for these conditions. An additional requirement for retreat of a model escarpment without decline is a long reaction time scale for fluvial entrainment. This corresponds to a substrate that is hard to detach by flucial erosion, and therefore to fluvial erosion that is not transport limited. Coninuous backtilting of an escarpment due ot flexural isostatic uplift in response to denudational unloading helps maintain the scarp top as a divide. It is essntial if the escarpment gradient is to be preserved during retreat in a uniform lithology. Low flexural rigidieties propote steep and slowly retreating escarpments. For given rainfall and substrate conditions, the morphology of a retraeating model escarpment is determined by the ratio of hte short-range diffusive and long range advective transport efficiencies. A low ration (which is interpreted to correspond to a more humid, temperate climate) produces a convex upper slope, and concave lower slope morphology and only major escarpments are predicted to preserve a high scarp gradient. Lithological contrasts in hte model produce more complex morphologies and predict the formation of scarps crowned by an erosionaly resistant caprock. However, resistant caprocks are not an essential requirement for model scarps to retreat. We conclude that the inferred controls and model behavior are both consistent with the present-day morphology of rifted continental margins and with modern conceptual models of landscape evolution.

Kooi, Henk↗
NASA NTRS1995

Boundary layer transition studies

A small-scale wind tunnel previously used for turbulent boundary layer experiments was modified for two sets of boundary layer transition studies. The first study concerns a laminar separation/turbulent reattachment. The pressure gradient and unit Reynolds number are the same as the fully turbulent flow of Spalart and Watmuff. Without the trip wire, a laminar layer asymptotes to a Falkner & Skan similarity solution in the FPG. Application of the APG causes the layer to separate and a highly turbulent and approximately 2D mean flow reattachment occurs downstream. In an effort to gain some physical insight into the flow processes a small impulsive disturbance was introduced at the C(sub p) minimum. The facility is totally automated and phase-averaged data are measured on a point-by-point basis using unprecedently large grids. The evolution of the disturbance has been tracked all the way into the reattachment region and beyond into the fully turbulent boundary layer. At first, the amplitude decays exponentially with streamwise distance in the APG region, where the layer remains attached, i.e. the layer is viscously stable. After separation, the rate of decay slows, and a point of minimum amplitude is reached where the contours of the wave packet exhibit dispersive characteristics. From this point, exponential growth of the amplitude of the disturbance is observed in the detached shear layer, i.e. the dominant instability mechanism is inviscid. A group of large-scale 3D vortex loops emerges in the vicinity of the reattachment. Remarkably, the second loop retains its identify far downstream in the turbulent boundary layer. The results provide a level of detail usually associated with CFD. Substantial modifications were made to the facility for the second study concerning disturbances generated by Suction Holes for laminar flow Control (LFC). The test section incorporates suction through interchangeable porous test surfaces. Detailed studies have been made using isolated holes in the impervious test plate that used to establish the Blasius base flow. The suction is perturbed harmonically and data are averaged on the basis of the phase of the disturbance, for conditions corresponding to strong suction and without suction. The technique was enhanced by using up to nine multiple probes to reduce the experimental run-time. In both cases, 3D contour surfaces in the vicinity of the hole show highly 3D TS waves which fan out in the spanwise direction forming bow-shaped waves downstream. The case without suction has proved useful for evaluating calculation methods. With suction, the perturbations on the centerline are much stronger and decay less rapidly, while the TS waves in the far field are similar to the case without suction. Downstream, the contour surfaces of the TS waves develop spanwise irregularities which eventually form into clumps. The spanwise clumping is evidence of a secondary instability that could be associated with suction vortices. Designers of porous surfaces use Goldsmith's Criterion to minimize cross-stream interactions. It is shown that partial TS wave cancellation is possible, depending on the hole spacing, disturbance frequency and free-stream velocity. New high-performance Constant Temperature Hot-Wire Anemometers were designed and built, based on a linear system theory analysis that can be extended to arbitrary order. The motivation was to achieve the highest possible frequency reponse while ensuring overall system stability. The performance is equal to or superior to commercially available instruments at about 10% of the cost. Details, such as fabrication drawings and a parts list, have been published to enable the instrument to be construced by others.

Watmuff, Jonathan H.↗
NASA NTRS2003

Residual Gas Effects on Detached Solidification in Microgravity

Many microgravity directional solidification experiments yielded ingots with portions that grew without contacting the ampoule wall, leading to greatly improved crystallographic perfection. Our long-term goal is to make such detached solidification reproducible, which requires a full understanding of the mechanisms underlying it. Our Moving Meniscus Model of steady-state detachment predicts that it depends strongly on the surface tension of the melt and the advancing contact angle with the ampoule wall. Detached solidification is more likely when the contact angle for the melt on the ampoule wall is high, i.e. non-wetting. It has been claimed that impurities increase the contact angle. The objective of the current project is to determine the influence of residual gases on the surface tension and contact angle of molten semiconductors on typical ampoule materials. We are focusing on determining the influence of oxygen on the contact angle of molten InSb on clean silica ('quartz'), including the advancing and retreating contact angles in addition to the usual equilibrium contact angle. We have created a gas flow system that allows us to control the oxygen partial pressure over a sessile drop of InSb on a horizontal quartz surface. The cell is slowly tilted while videotaping to reveal the contact angles on the two sides of the drop just prior to it rolling down the surface. Thus far, we have learned the following: (1) Molten InSb readily forms an oxide layer in the presence of the trace amounts of oxygen found in high purity argon; (2) This oxide contains a substantial amount of Ga, which presumably is a trace contaminant that is not detectable in the starting material; (3) The addition of 10% hydrogen to the argon gas is sufficient to reduce the oxide and produce a clean drop; (4) An infrared filter must precede the video camera in order to produce a sharp image of the drop for later image analysis; (5) Tilting the surface on which the drop rests causes the two sides of the drop to display different contact angles, reflecting contact line sticking; (6) Vibration strongly accelerates the approach of the drop to its final shape on a horizontal surface by helping to overcome sticking of the contact line; (7) Oscillation of the drop surface due to vibration appears to increase as the surface is inclined from horizontal. Presumably, the angle at which the drop rolls down the surface is also reduced by vibration. This observation is particularly significant, as the meniscus must move along the ampoule wall during detached solidification.

Regel, Liya L.↗
NASA NTRS2006

Laser Mapping for Visual Inspection and Measurement

Each space shuttle orbiter has 38 Primary Reaction Control System (PRCS) thrusters to help power and position the vehicle for maneuvers in space, including reentry and establishing Earth orbit. Minor flaws in the ceramic lining of a thruster, such as a chip or crack, can cripple the operations of an orbiter in space and jeopardize a mission. The ability to locate, measure, and monitor tiny features in difficult-to-inspect PRCS thrusters improves their overall safety and lifespan. These thrusters have to be detached and visually inspected in great detail at one of two NASA facilities, the White Sands Test Facility or the Kennedy Space Center, before and after each mission, which is an expense of both time and money.

Source record↗
DOE OSTI2020

Improved core-edge compatibility using impurity seeding in the small angle slot (SAS) divertor at DIII-D

Impurity seeding studies in the slot divertor (SAS) at DIII-D have revealed a strong relationship between the detachment onset and pedestal characteristics with both target geometry and impurity species. N 2 seeding in the slot has led to the first simultaneous observation of detachment on the entire suite of boundary diagnostics viewing the SAS without degradation of core confinement. SOLPS-ITER simulations with D+C+N, full cross-field drifts and n-n collisions activated are performed for the first time in DIII-D to interpret the behavior. This illustrates a strong effect of divertor configuration and plasma drifts on the recycling source distribution with significant consequences on plasma flows. Flow reversal is found for both main ions and impurities affecting strongly the impurity transport and providing an explanation for the observed dependence on strike point location of the detachment onset and impurity leakage found in the experiments. Matched discharges with either nitrogen or neon injection show that while nitrogen does not significantly affect the pedestal, neon leads to increased pedestal pressure gradient and improved pedestal stability. Little nitrogen penetrates in the core, but a great amount of neon is found in the pedestal consistent with the different ionization potentials of the two impurities. This research demonstrates that neutral and impurity distributions in the divertor can be controlled through variations in strike point locations in a fixed baffle structure. Divertor geometry combined with impurity seeding enables mitigated divertor heat flux balancing core contamination and thus leading to enhanced divertor dissipation and improved core-edge compatibility which are essential for ITER and for future fusion reactors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1992

Altering the cellular mechanical force balance results in integrated changes in cell, cytoskeletal and nuclear shape

Studies were carried out with capillary endothelial cells cultured on fibronectin (FN)-coated dishes in order to analyze the mechanism of cell and nuclear shape control by extracellular matrix (ECM). To examine the role of the cytoskeleton in shape determination independent of changes in transmembrane osmotic pressure, membranes of adherent cells were permeabilized with saponin (25 micrograms/ml) using a buffer that maintains the functional integrity of contractile microfilaments. Real-time videomicroscopic studies revealed that addition of 250 microM ATP resulted in time-dependent retraction and rounding of permeabilized cells and nuclei in a manner similar to that observed in intact living cells following detachment using trypsin-EDTA. Computerized image analysis confirmed that permeabilized cells remained essentially rigid in the absence of ATP and that retraction was stimulated in a dose-dependent manner as the concentration of ATP was raised from 10 to 250 microM. Maximal rounding occurred by 30 min with projected cell and nuclear areas being reduced by 69 and 41%, respectively. ATP-induced rounding was also accompanied by a redistribution of microfilaments resulting in formation of a dense net of F-actin surrounding retracted nuclei. Importantly, ATP-stimulated changes in cell, cytoskeletal, and nuclear form were prevented in permeabilized cells using a synthetic myosin peptide (IRICRKG) that has been previously shown to inhibit actomyosin filament sliding in muscle. In contrast, both the rate and extent of cell and nuclear rounding were increased in permeabilized cells exposed to ATP when the soluble FN peptide, GRGDSP, was used to dislodge immobilized FN from cell surface integrin receptors.(ABSTRACT TRUNCATED AT 250 WORDS).

Non-NASA Center↗
NASA NTRS1992

Pressurized Lunar Rover

The pressurized lunar rover (PLR) consists of a 7 m long, 3 m diameter cylindrical main vehicle and a trailer which houses the power and heat rejection systems. The main vehicle carries the astronauts, life support systems, navigation and communication systems, directional lighting, cameras, and equipment for exploratory experiments. The PLR shell is constructed of a layered carbon-fiber/foam composite. The rover has six 1.5 m diameter wheels on the main body and two 1.5 m diameter wheels on the trailer. The wheels are constructed of composites and flex to increase traction and shock absorption. The wheels are each attached to a double A-arm aluminum suspension, which allows each wheel 1 m of vertical motion. In conjunction with a 0.75 m ground clearance, the suspension aids the rover in negotiating the uneven lunar terrain. The 15 N-m torque brushless electric motors are mounted with harmonic drive units inside each of the wheels. The rover is steered by electrically varying the speeds of the wheels on either side of the rover. The PLR trailer contains a radiosotope thermoelectric generator providing 6.7 kW. A secondary back-up energy storage system for short-term high-power needs is provided by a bank of batteries. The trailer can be detached to facilitate docking of the main body with the lunar base via an airlock located in the rear of the PLR. The airlock is also used for EVA operation during missions. Life support is a partly regenerative system with air and hygiene water being recycled. A layer of water inside the composite shell surrounds the command center. The water absorbs any damaging radiation, allowing the command center to be used as a safe haven during solar flares. Guidance, navigation, and control are supplied by a strapdown inertial measurement unit that works with the on-board computer. Star mappers provide periodic error correction. The PLR is capable of voice, video, and data transmission. It is equipped with two 5 W X-band transponder, allowing simultaneous transmission and reception. An S-band transponder is used to communicate with the crew during EVA. The PLR has a total mass of 6197 kg. It has a nominal speed of 10 km/hr and a top speed of 18 km/hr. The rover is capable of towing 3 metric tons (in addition to the RTG trailer).

Creel, Kenneth↗
NASA NTRSDate not supplied

High-Fidelity Simulations of a Quadrotor Vehicle for Urban Air Mobility

High-fidelity computational fluid dynamics simulations have been carried out to analyze NASA’s quadrotor air taxi concept for urban air mobility. High-order accurate schemes, dual-time stepping, and the delayed detached-eddy simulation model have been employed. The flow solver has been loosely coupled with the rotorcraft comprehensive analysis code. The vehicle simulated is a six-passenger quadrotor for air taxi operations. The quadrotor has been simulated in hover and cruise, with flight conditions representative of an air taxi mission. Initially, the quadcopter vehicle is analyzed using low-fidelity tools. Then, a complete analysis using high-fidelity simulations of the quadcopter is performed in conjunction with collective pitch control. Airloads, wake geometry, and performance are studied and compared. A comparison between isolated rotors and complete vehicle simulations is presented. NASA’s quadrotor is one of NASA’s concept vehicles designed in support of aircraft development for vertical take-off and landing air taxi operations.

ARMD↗
DOE OSTI2022

Electrochemical Control of the Morphology and Functional Properties of Hierarchically Structured, Dendritic Cu Surfaces

Electrodeposited dendritic copper foams have been extensively studied as an electrocatalyst for CO 2 reduction reaction (CO 2 RR). Many parameters, such as dendrite size, porosity, pore size, and crystal faceting, define the hierarchical properties of these structures and their subsequent bubble evolution and CO 2 RR capabilities. Herein, the effects the electrodeposition conditions (potential, pH) have on the resulting crystallinity, microstructure, and macroporosity of the copper foam are studied. These morphological differences and the corresponding effects on electrocatalytic activity are characterized. It is shown that the composition of the electrodeposition bath can have significant effects on the mechanics of bubble formation and detachment at the surface during hydrogen evolution reaction in acidic solutions. Similarly, the electrodeposition conditions for the synthesis of the foam affect the product selectivity during CO 2 RR electrocatalysis. As a result, foams deposited in alkaline electrodeposition solutions show high faradaic efficiency and specificity toward C 2 H 6 , an uncommon product of CO 2 RR, at modest applied potentials (−0.8 V versus reversible hydrogen electrode.

14 SOLAR ENERGY↗
NASA NTRSDate not supplied

Computational Investigation of Retropropulsion Operating Environments with a GPU-Enabled Detached Eddy Simulation Approach

Human exploration of the surface of Mars will require an extended powered descent phase of flight, during which aerodynamic-propulsive interference effects can be significant. Characterization of these environments to enable implementation of this technology into a flight vehicle will rely heavily on computational simulation. This work advances the understanding of retropropulsion aerodynamics through application of a massively parallel detached eddy simulation approach on a GPU-accelerated computational framework, yielding data that are largely unachievable with conventional high-performance computing resources. This work includes time-dependent and time-averaged forces and moments on a conceptual, full-scale vehicle in environments and operating conditions relevant to human Mars exploration. Conditions are examined where the engine exhaust flow transitions between over-expanded and under-expanded flow structures, and flight operation will require the ability to maintain control of the vehicle during such a transition. These transitions occur as the vehicle decelerates, and as such, this investigation includes supersonic, transonic, and subsonic flight conditions. Options for vehicle control during powered flight include differential throttling of the engines. This paper provides an overview of the computational campaign, approach, and discussion of results in characterizing the resulting aerodynamics for differential throttling with retropropulsion in atmospheric environments.

EDL↗
NASA NTRS1999

Evaluation of Alternate Control Surface Concepts

Although several viable concepts have been investigated during recent years, time constraints do not allow for a detailed discussion of each. Therefore, only a small segment of these concepts will be discussed during this workshop. Emphasis will be placed on canards, forebody chimes and wing fins. The majority of the data presented were obtained using a 0.01542 scale representation of the HSR Reference-H model. This model was similar in planform, and incorporated fullspan leading-edge flaps and segmented trailing-edge flaps. The high-lift configuration of leading-edges at 30 degrees, and trailing-edges at 10 degrees are shown. The wing had no twist or camber. The forebody and fuselage were simple bodies of revolution. A detachable aft fuselage, complete with empennage, was incorporated during the chine study, and removed during the canard tests. The overall length (including aft fuselage) was approximately 58 inches; and the span was 24 inches.

Campbell, Bryan↗
NASA NTRS1996

Experimental Investigation of Pool Boiling Heat Transfer Enhancement in Microgravity in the Presence of Electric Fields

Boiling is an effective mode of heat transfer since high heat flux levels are possible driven by relatively small temperature differences. The high heat transfer coefficients associated with boiling have made the use of these processes increasingly attractive to aerospace engineering. Applications of this type include compact evaporators in the thermal control of aircraft avionics and spacecraft environments, heat pipes, and use of boiling to cool electronic equipment. In spite of its efficiency, cooling based on liquid-vapor phase change processes has not yet found wide application in aerospace engineering due to specific problems associated with the low gravity environment. After a heated surface has reached the superheat required for the initiation of nucleate boiling, bubbles will start forming at nucleation sites along the solid interface by evaporation of the liquid. Bubbles in contact with the wall will continue growing by this mechanism until they detach. In terrestrial conditions, bubble detachment is determined by the competition between body forces (e.g. buoyancy) and surface tension forces that act to anchor the bubble along the three phase contact line. For a given body force potential and a balance of tensions along the three phase contact line, bubbles must reach a critical size before the body force can cause them to detach from the wall. In a low gravity environment the critical bubble size for detachment is much larger than under terrestrial conditions, since buoyancy is a less effective means of bubble removal. Active techniques of heat transfer enhancement in single phase and phase change processes by utilizing electric fields have been the subject of intensive research during recent years. The field of electrohydrodynamics (EHD) deals with the interactions between electric fields, flow fields and temperature fields. Previous studies indicate that in terrestrial applications nucleate boiling heat transfer can be increased by a factor of 50 as compared to values obtained for the same system without electric fields. Imposing an external electric field holds the promise to improve pool boiling heat transfer in low gravity, since a phase separation force other than gravity is introduced. The goal of our research is to experimentally investigate the potential of EHD and the mechanisms responsible for EHD heat transfer enhancement in boiling in low gravity conditions.

Herman, Cila↗
NASA NTRS2005

Measurement of the Shear Lift Force on a Bubble in a Channel Flow

Two-phase flow systems play vital roles in the design of some current and anticipated space applications of two-phase systems which include: thermal management systems, transfer line flow in cryogenic storage, space nuclear power facilities, design and operation of thermal bus, life support systems, propulsion systems, In Situ Resource Utilization (ISRU), and space processes for pharmaceutical applications. The design of two-phase flow systems for space applications requires a clear knowledge of the behaviors of the dispersed phase (bubble), its interaction with the continuous phase (liquid) and its effect on heat and mass transfer processes, The need to understand the bubble generation process arises from the fact that for all space applications, the size and distribution of bubbles are extremely crucial for heat and mass transfer control. One important force in two-phase flow systems is the lift force on a bubble or particle in a liquid shear flow. The shear lift is usually overwhelmed by buoyancy in normal gravity, but it becomes an important force in reduced gravity. Since the liquid flow is usually sheared because of the confining wall, the trajectories of bubbles and particles injected into the liquid flow are affected by the shear lift in reduced gravity. A series of experiments are performed to investigate the lift force on a bubble in a liquid shear flow and its effect on the detachment of a bubble from a wall under low gravity conditions. Experiments are executed in a Poiseuille flow in a channel. An air-water system is used in these experiments that are performed in the 2.2 second drop tower. A bubble is injected into the shear flow from a small injector and the shear lift is measured while the bubble is held stationary relative to the fluid. The trajectory of the bubble prior, during and after its detachment from the injector is investigated. The measured shear lift force is calculated from the trajectory of the bubble at the detachment point. These values for the shear lift are then compared with the theoretical predictions from various published works on shear lift in the open literature, which include asymptotic solutions at low bubble Reynolds number, potential flow predictions and numerical studies that deal with intermediate bubble Reynolds numbers.

Nahra, Henry K.↗
DOE OSTI2022

Recombinant FimH Adhesin Demonstrates How the Allosteric Catch Bond Mechanism Can Support Fast and Strong Bacterial Attachment in the Absence of Shear

The FimH protein of Escherichia coli is a model two-domain adhesin that is able to mediate an allosteric catch bond mechanism of bacterial cell attachment, where the mannose-binding lectin domain switches from an ‘inactive’ conformation with fast binding to mannose to an ‘active’ conformation with slow detachment from mannose. Because mechanical tensile force favors separation of the domains and, thus, FimH activation, it has been thought that the catch bonds can only be manifested in a fluidic shear-dependent mode of adhesion. Here, we used recombinant FimH variants with a weakened inter-domain interaction and show that a fast and sustained allosteric activation of FimH can also occur under static, non-shear conditions. Moreover, it appears that lectin domain conformational activation happens intrinsically at a constant rate, independently from its ability to interact with the pilin domain or mannose. However, the latter two factors control the rate of FimH deactivation. Thus, the allosteric catch bond mechanism can be a much broader phenomenon involved in both fast and strong cell-pathogen attachments under a broad range of hydrodynamic conditions. In conclusion, this concept that allostery can enable more effective receptor-ligand interactions is fundamentally different from the conventional wisdom that allostery provides a mechanism to turn binding off under specific conditions.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Development of an integrated core–edge scenario using the super H-mode

An optimized pedestal regime called the super-H (SH) mode is leveraged to couple a fusion relevant core plasma with a high density scrape-off layer appropriate for realistic reactor power exhaust solutions. Recent DIII-D experiments have expanded the operating space of the SH regime using advanced control algorithms and investigated optimization of impurity seeding, deuterium gas puffing, and 3D magnetic perturbations. Simultaneous real-time control of the pedestal density and radiated power with in-vessel coils and nitrogen seeding enable optimal coupled divertor and pedestal conditions. Four case studies are analysed with varied levels of radiated power in the divertor volume ranging from 0 (no seeding) to 8.5 MW radiated from carbon and nitrogen emission. Plasmas with a 4.5 MW radiated power target establish a radiative mantle, leading to divertor temperatures of ~16 eV while maintaining SH-mode, and with only marginal impact on the pedestal and core performance. Increased levels of N 2 seeding with a 7.5 MW radiated power target facilitate detachment onset and divertor temperatures <5 eV, with no degradation in stored energy and the operational point remaining inside the SH-mode channel for $ > 2.5{\tau }_{\text{E}}$. Finally, a 8.5 MW radiated power target leads to partial detachment, which is so far associated with the loss of access to SH-mode pedestal conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1982

Lessons learned - Americans in space

Milestones in the learning process during development of spaceflight capability for different NASA missions are traced from the initial launch of the Mercury escape rocket to the advent of the Shuttle. A detached heat shield on the first manned Mercury orbital flight led to a decision for reentry with retrorockets attached, a situation which demonstrated a need for on-line communications with the spacecraft construction engineers. The Gemini program served to develop EVA techniques and docking procedures essential for the Apollo missions. Apollo 8 circled the moon after only one manned test flight of the equipment due to the success of the first flight. Lunar landing simulation training exposed the astronauts to situations beyond the human ability to respond. The training was justified when computer overload required the pilot to retake manual control of some spacecraft functions during the successful first lunar landing. All lessons previously learned were used to safely return the damaged Apollo 13 to earth. The Skylab missions provided an opportunity to maintain rotating teams of flight controllers on a 24-hr/day basis for periods of months. Finally, the six-year hiatus of U.S. manned space activities between the end of the Skylab missions and the first Shuttle flight provided time for incorporating previous lessons into new procedures, training strategies, and data resources.

Kranz, E.↗