Search NASA⌕ Search

SEARCH · Search NASA

Results for “general linear methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Progressive Aerodynamic Model Identification From Dynamic Water Tunnel Test of the F-16XL Aircraft

Development of a general aerodynamic model that is adequate for predicting the forces and moments in the nonlinear and unsteady portions of the flight envelope has not been accomplished to a satisfactory degree. Predicting aerodynamic response during arbitrary motion of an aircraft over the complete flight envelope requires further development of the mathematical model and the associated methods for ground-based testing in order to allow identification of the model. In this study, a general nonlinear unsteady aerodynamic model is presented, followed by a summary of a linear modeling methodology that includes test and identification methods, and then a progressive series of steps suggesting a roadmap to develop a general nonlinear methodology that defines modeling, testing, and identification methods. Initial steps of the general methodology were applied to static and oscillatory test data to identify rolling-moment coefficient. Static measurements uncovered complicated dependencies of the aerodynamic coefficient on angle of attack and sideslip in the stall region making it difficult to find a simple analytical expression for the measurement data. In order to assess the effect of sideslip on the damping and unsteady terms, oscillatory tests in roll were conducted at different values of an initial offset in sideslip. Candidate runs for analyses were selected where higher order harmonics were required for the model and where in-phase and out-of-phase components varied with frequency. From these results it was found that only data in the angle-of-attack range of 35 degrees to 37.5 degrees met these requirements. From the limited results it was observed that the identified models fit the data well and both the damping-in-roll and the unsteady term gain are decreasing with increasing sideslip and motion amplitude. Limited similarity between parameter values in the nonlinear model and the linear model suggest that identifiability of parameters in both terms may be a problem. However, the proposed methodology can still be used with careful experiment design and carefully selected values of angle of attack, sideslip, amplitude, and frequency of the oscillatory data.

Murphy, Patrick C.↗

Study of Systems Using Inertia Wheels for Precise Attitude Control of a Satellite

Systems using inertia wheels are evaluated in this report to determine their suitability for precise attitude control of a satellite and to select superior system configurations. Various possible inertia wheel system configurations are first discussed in a general manner. Three of these systems which appear more promising than the others are analyzed in detail, using the Orbiting Astronomical Observatory as an example. The three systems differ from each other only by the method of damping, which is provided by either a rate gyro, an error-rate network, or a tachometer in series with a high-pass filter. An analytical investigation which consists of a generalized linear analysis, a nonlinear analysis using the switching-time method, and an analog computer study shows that all three systems are theoretically capable of producing adequate response and also of maintaining the required pointing accuracy for the Orbiting Astronomical Observatory of plus or minus 0.1 second of arc. Practical considerations and an experimental investigation show, however, that the system which uses an error-rate network to provide damping is superior to the other two systems. The system which uses a rate gyro is shown to be inferior because the threshold level causes a significant amount of limit-cycle operation, and the system which uses a tachometer with a filter is shown to be inferior because a device with the required dynamic range of operation does not appear to be available. The experimental laboratory apparatus used to investigate the dynamic performance of the systems is described, and experimental results are included to show that under laboratory conditions with relatively large extraneous disturbances, a dynamic tracking error of less than plus or minus 0.5 second of arc was obtained.

White, John S.↗

A finite element method for potential aerodynamics around complex configurations

A general formulation for steady and oscillatory, subsonic and supersonic, potential linearized aerodynamic flow around complex configurations is presented. A linear integral equation relating the unknown potential on the surface of the body to the known downwash is used. The formulation is applied to the analysis of the flow field around wings and wing-body combinations. The surface is divided into small quadrilateral elements which are approximated with a hyperboloidal surface. The potential is assumed to be constant within each element. This yields a set of linear algebraic equations. The coefficients are evaluated analytically. Numerical results for steady and oscillatory, subsonic and supersonic flows indicate that the method, intrinsically general and flexible, is also fast, accurate and in excellent agreement with existing results.

Chen, L.-T.↗

Relativistic density functional theory in the full potential linear muffin tin orbital method

In this write-up, we have outlined the general methodology for treating relativity in the FP-LMTO method. The Schrodinger equation is insufficient for describing the physics of heavy elements because it leaves out any relativistic effects. Therefore DFT based on the Schrodinger equation is not sufficient for studying heavy materials. It is, however, possible to incorporate all of the effects of relativity in DFT if starting with a reformulation of the Hohenberg-Kohn theorem that proceeds from the Dirac equation, rather than the Schrodinger equation. The corresponding theorem in relativistic density functional theory (RDFT) shows that the ground-state density of the system is a functional of not only the charge density as in Schrodinger-based DFT, but also of the current density. This leads to a more elaborate procedure in practice when solving the Dirac-Kohn-Sham equations, the relativistic analogs of the Kohn-Sham equations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Explicit Runge–Kutta Methods that Alleviate Order Reduction

Explicit Runge–Kutta (RK) methods are susceptible to a reduction in the observed order of convergence when applied to an initial boundary value problem with time-dependent boundary conditions. We study conditions on explicit RK methods that guarantee high order convergence for linear problems; we refer to these conditions as weak stage order conditions. We prove a general relationship between the method’s order, weak stage order, and number of stages. Furthermore, we derive explicit RK methods with high weak stage order and demonstrate, through numerical tests, that they avoid the order reduction phenomenon up to any order for linear problems and up to order three for nonlinear problems.

explicit Runge–Kutta↗

Linear response to long wavelength fluctuations using curvature simulations

We study the local response to long wavelength fluctuations in cosmological N -body simulations, focusing on the matter and halo power spectra, halo abundance and non-linear transformations of the density field. The long wavelength mode is implemented using an effective curved cosmology and a mapping of time and distances. The method provides an alternative, more direct, way to measure the isotropic halo biases. Limiting ourselves to the linear case, we find generally good agreement between the biases obtained from the curvature method and the traditional power spectrum method at the level of a few percent. We also study the response of halo counts to changes in the variance of the field and find that the slope of the relation between the responses to density and variance differs from the naïve derivation assuming a universal mass function by approximately 8–20%. This has implications for measurements of the amplitude of local non-Gaussianity using scale dependent bias. We also analyze the halo power spectrum and halo-dark matter cross-spectrum response to long wavelength fluctuations and derive second order halo bias from it, as well as the super-sample variance contribution to the galaxy power spectrum covariance matrix.

79 ASTRONOMY AND ASTROPHYSICS↗

Survey of fracture toughness test methods

Comprehensive survey presents current methods of fracture toughness testing that are based on linear elastic fracture mechanics. General principles of the basic two dimensional crack stress field model are discussed in relation to real three dimensional specimens. Methods of test instrumentation and procedure are described.

Brown, W. F., Jr.↗

Propagator for the general time-dependent harmonic oscillator with application to an ion trap

We present the simplest possible formula for the propagator of the general time-dependent quadratic Hamiltonian, including linear terms. The method is based on the use of a linear time-dependent invariant and requires only the solution of a linear homogeneous second-order ordinary differential equation corresponding to the classical quadratic Hamiltonian. We give an example for the case of the Paul trap.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electronic band structure and optical properties of titanium oxyphosphates Li{sub 0.50}Co{sub 0.25}TiO(PO{sub 4}) single crystals: An ab-initio calculations

From the refined atomic positions obtained by Belmal et al. (2004) using X-ray diffraction for Li{sub 0.50}Co{sub 0.25}TiO(PO{sub 4}), we have performed a structural optimization by minimizing the forces acting on the atoms keeping the lattice parameters fixed at the experimental values. With this relaxed (optimized) geometry we have performed a comprehensive theoretical study of electronic properties and dispersion of the linear optical susceptibilities using the full potential linear augmented plane wave (FP-LAPW) method. The generalized gradient approximation (GGA) exchange-correlation potential was applied. In addition, the Engel-Vosko generalized gradient approximation (EVGGA) was used for comparison with GGA because it is known that EVGGA approach yields better band splitting compared to the GGA. We have calculated the band structure, and the total and partial densities of states. The electron charge densities and the bonding properties were analyzed and discussed. The complex dielectric optical susceptibilities were discussed in detail. - Graphical abstract: It is shown that P is tetrahedrally coordinated by four O ions. Highlights: > Comprehensive theoretical study of electronic and optical properties was performed. > Using X-ray diffraction data we have performed a structural optimization. > The electron charge densities and the bonding properties were analyzed and discussed. > Fermi surface was analyzed since it is useful for predicting thermal, magnetic, and optical properties. > The density of states at E{sub F} and the electronic specific heat coefficient were calculated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermoelectric, electronic, optical and chemical bonding properties of Ba{sub 2}PrRuO{sub 6}: At temperature 7 K and 150 K

Highlights: • DFT-FPLAPW method used for calculating the electronic structure. • The Fermi surface of BPRO (7 K and 150 K) is also calculated. • The complex dielectric function has been calculated. • Thermoelectric properties were also calculated using BoltzTraP code. • Power factor shows that both compounds are good thermoelectric materials at 600 K. - Abstract: We present first principles calculations of the band structure, density of states, electronic charge density, Fermi surface and optical properties of Ba{sub 2}PrRuO{sub 6} single crystals at two different temperatures. The atomic positions were optimized by minimizing the forces acting on the atoms. We have employed the full potential linear augmented plane wave method within local density approximation, generalized gradient approximation and Engel–Vosko generalized gradient approximation to treat the exchange correlation potential. The calculation shows that the compound is superconductor with strong hybridization near the Fermi energy level. Fermi surface is composed of two sheets. The calculated electronic specific heat capacities indicate, very close agreement with the experimental one. The bonding features of the compounds are analyzed using the electronic charge density in the (1 0 0) and (0–10) crystallographic planes. The dispersion of the optical constants was calculated and discussed. The thermoelectric properties are also calculated using the BoltzTrap code.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electronic structure, elasticity, bonding features and mechanical behaviour of zinc intermetallics: A DFT study

The structural stability, electronic structure, elastic and mechanical properties of TiZn and ZrZn intermetallics have been studied using ab-initio full potential linearized augmented plane wave (FP-LAPW) method within generalized gradient approximation for exchange and correlation potentials. The various structural parameters, such as lattice constant (a{sub 0}), bulk modulus (B), and its pressure derivative (B’) are analysed and compared. The investigation of elastic constants affirm that both TiZn and ZrZn are elastically stable in CsCl (B{sub 2} phase) structure. The electronic structures have been analysed quantitatively from the band structure which reveals the metallic nature of these compounds. To better illustrate the nature of bonding and charge transfer, we have also studied the Fermi surfaces. The three well known criterion of ductility namely Pugh’s rule, Cauchy’s pressure and Frantsevich rule elucidate the ductile nature of these compounds.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Structural, electronic and elastic properties of REIr{sub 2} (RE=La and Ce) Laves phase compounds

REIr{sub 2} (RE = La and Ce) Laves phase intermetallic compounds were investigated with respect to their structural, electronic and elastic properties using full potential linearized augmented plane wave (FP-LAPW) method within generalized gradient approximation (GGA) as implemented in WIEN2k code. The ground state properties such as lattice constants (a{sub 0}), bulk modulus (B), pressure derivative of bulk modulus (B′) and density of state at Fermi level N(E{sub F}) have been obtained by optimization method. The electronic structure (BS, TDOS and PDOS) reveals that these Laves phase compounds are metallic in nature. The calculated elastic constants indicate that these compounds are mechanically stable at ambient pressure and found to be ductile in nature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Restoration of degraded images by composite gratings in a coherent optical processor.

A study has been made on restoration of degraded images utilizing spatial filtering techniques in a coherent optical processor. This study differs from other coherent approaches in that the spatial filters employed contain only composite gratings that are quite simple to produce. A general method of synthesizing the appropriate composite gratings for linearly smeared as well as multiply exposed and out-of-focus images will be presented in some detail with experimental results. The extension of the method of synthesis to other types of degradation is briefly discussed.

Jablonowski, D. P.↗

An assessment of preliminary aerodynamic analysis methods for supersonic speeds including high angle-of-attack flow

The problems associated with predicting the aerodynamic loads for moderate supersonic Mach number, high angle-of-attack flows and for high supersonic Mach number flows are addressed. For these large disturbance-type flows, commonly used prediction methods based on linearized theory or on the tangent-wedge method are shown to be generally inadequate. For the preliminary analysis of aerodynamic shapes subjected to these type flows, two methods have recently been developed by combining features of the linearized theory and tangent-wedge method. These two new methods are discussed, and through extensive comparisons with experimental data, are shown to offer an improved prediction capability.

Pittman, J. L.↗

Results of including geometric nonlinearities in an aeroelastic model of an F/A-18

An integrated, nonlinear simulation model suitable for aeroelastic modeling of fixed-wing aircraft has been developed. While the author realizes that the subject of modeling rotating, elastic structures is not closed, it is believed that the equations of motion developed and applied herein are correct to second order and are suitable for use with typical aircraft structures. The equations are not suitable for large elastic deformation. In addition, the modeling framework generalizes both the methods and terminology of non-linear rigid-body airplane simulation and traditional linear aeroelastic modeling. Concerning the importance of angular/elastic inertial coupling in the dynamic analysis of fixed-wing aircraft, the following may be said. The rigorous inclusion of said coupling is not without peril and must be approached with care. In keeping with the same engineering judgment that guided the development of the traditional aeroelastic equations, the effect of non-linear inertial effects for most airplane applications is expected to be small. A parameter does not tell the whole story, however, and modes flagged by the parameter as significant also need to be checked to see if the coupling is not a one-way path, i.e., the inertially affected modes can influence other modes.

Buttrill, Carey S.↗

Self-assembled elastomers with molecularly encoded tissue-like softness, strain-adaptive stiffening and coloration

The invention generally relates to linear-bottlebrush-linear copolymer blocks and methods of making and using same. The disclosed copolymer blocks can be useful in, for example, the formation of polymer networks that replicate biological stress-strain behavior. This abstract is intended as a scanning tool for purposes of searching in the particular art and is not intended to be limiting of the present invention.

Sheiko, Sergei↗

Blending Velocities In Task Space In Computing Robot Motions

Blending of linear and angular velocities between sequential specified points in task space constitutes theoretical basis of improved method of computing trajectories followed by robotic manipulators. In method, generalized velocity-vector-blending technique provides relatively simple, common conceptual framework for blending linear, angular, and other parametric velocities. Velocity vectors originate from straight-line segments connecting specified task-space points, called "via frames" and represent specified robot poses. Linear-velocity-blending functions chosen from among first-order, third-order-polynomial, and cycloidal options. Angular velocities blended by use of first-order approximation of previous orientation-matrix-blending formulation. Angular-velocity approximation yields small residual error, quantified and corrected. Method offers both relative simplicity and speed needed for generation of robot-manipulator trajectories in real time.

Volpe, Richard A.↗

Structural fluctuation of proteins induced by thermodynamic perturbation

A theory to describe structural fluctuations of protein induced by thermodynamic perturbations, pressure, temperature, and denaturant, is proposed. The theory is formulated based on the three methods in the statistical mechanics: the generalized Langevin theory, the linear response theory, and the three dimensional interaction site model (3D-RISM) theory. The theory clarifies how the change in thermodynamic conditions, or a macroscopic perturbation, induces the conformational fluctuation, which is a microscopic property. The theoretical results are applied, on the conceptual basis, to explain the experimental finding by Akasaka et al., concerning the NMR experiment which states that the conformational change induced by pressure corresponds to structural fluctuations occurring in the ambient condition. A method to evaluate the structural fluctuation induced by pressure is also suggested by means of the 3D-RISM and the site-site Kirkwood-Buff theories.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗