Search NASA⌕ Search

SEARCH · Search NASA

Results for “gyro”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Review of mechanical vibration tests conducted on control moment gyros and life test fixtures

Experimental vibration studies performed on a number of flight control moment gyros and bearing life test fixtures are summarized. Tests were performed at MSFC, at Wyle Laboratories, Huntsville, Alabama, and at the Bendix Corporation facilities in Teterboro, New Jersey. A description of test and analysis equipment is included as well as test procedures and overall performance rankings. Advanced ultrasonic rolling element bearing fault detection techniques were applied for bearing analysis along with conventional vibration and sound analysis procedures.

Burchill, R. F.↗
NASA NTRS1973

2-SPEED, a single-gimbal control moment gyro attitude control system.

In 2-SPEED (Two Scissored Pair Ensemble, Explicit Distribution) four single-gimbal control moment gyros (SGCMGs) configured into two scissored pairs are combined with an explicit distribution of angular momentum between pairs to produce a system relatively insensitive to the singularity problems which have plagued other SGCMG concepts. In this system, the singularity surfaces in momentum space degenerate to discrete curves. Further, the system permits a smooth passage through these remaining singularities with, at worst, a temporary delay while momentum redistribution takes place. Finally, CMG-out operation is possible within the full volume of the reduced momentum envelope.

Crenshaw, J. W.↗
NASA NTRS1974

Modern control techniques in active flutter suppression using a control moment gyro

Development of organized synthesis techniques, using concepts of modern control theory was studied for the design of active flutter suppression systems for two and three-dimensional lifting surfaces, utilizing a control moment gyro (CMG) to generate the required control torques. Incompressible flow theory is assumed, with the unsteady aerodynamic forces and moments for arbitrary airfoil motion obtained by using the convolution integral based on Wagner's indicial lift function. Linear optimal control theory is applied to find particular optimal sets of gain values which minimize a quadratic performance function. The closed loop system's response to impulsive gust disturbances and the resulting control power requirements are investigated, and the system eigenvalues necessary to minimize the maximum value of control power are determined.

Buchek, P. M.↗
NASA NTRS1973

RI 1170 advanced strapdown gyro

The major components of the RI 1170 gyroscope are described. A detailed functional description of the electronics including block diagrams and photographs of output waveshapes within the loop electronics are presented. An electronic data flow diagram is included. Those gyro subassemblies that were originally planned and subsequently changed or modified for one reason or another are discussed in detail. Variations to the original design included the capacitive pickoffs, torquer flexleads, magnetic suspension, gas bearings, electronic design, and packaging. The selection of components and changes from the original design and components selected are discussed. Device failures experienced throughout the program are reported and design corrections to eliminate the failure modes are noted. Major design deficiencies such as those of the MSE electronics are described in detail. Modifications made to the gas bearing parts and design improvements to the wheel are noted. Changes to the gas bearing prints are included as well as a mathematical analysis of the 1170 gas bearing wheel by computer analysis. The mean free-path effects on gas bearing performance is summarized.

Source record↗
NASA NTRS1974

A strapdown laser gyro navigator

A broad spectrum of commercial and military vehicles employ some form of inertial measurement equipment. In general this equipment has a special purpose in that it was tailored for each specific application thereby resulting in high installation and maintenance costs. Recently the emphasis has been directed toward developing low cost building blocks from which the desired inertial functions can be derived. This paper describes a National Aeronautics and Space Administration (NASA) program that combines inertial system sensor and computational advances into a flight demonstration configuration. Specifically, an inertial navigation system employing strapdown laser gyro angular rate sensors and a miniature, modular digital flight computer is described. The objective of this program is to demonstrate, via flight test evaluation, the capabilities of the advanced sensor and computer as they apply to future low cost, high reliability inertial system applications.

Garret, H.↗
NASA NTRS1974

A steering law for a roof-type configuration for a single-gimbal control moment gyro system

Single-Gimbal Control Moment Gyro (SGCMG) systems have been investigated for attitude control of the Large Space Telescope (LST) and the High Energy Astronomy Observatory (HEAO). However, various proposed steering laws for the SGCMG systems thus far have some defects because of singular states of the system. In this report, a steering law for a roof-type SGCMG system is proposed which is based on a new momentum distribution scheme that makes all the singular states unstable. This momentum distribution scheme is formulated by a treatment of the system as a sampled-data system. From analytical considerations, it is shown that this steering law gives control performance which is satisfactory for practical applications. Results of the preliminary computer simulation entirely support this premise.

Yoshikawa, T.↗
NASA NTRS1975

A steering law for three double-gimbal control moment gyro systems

A steering law for three double-gimbal control moment gyro (CMG) systems is proposed. This steering law is applicable to systems with almost any configuration of CMGs and the CMG-out operation needs no special modification. Examples of three double gimbal CMG systems in an orthogonal configuration and in a parallel configuration are shown along with the results of digital simulations. Simulation results show that any command torque can always be met except when the system is in a singular state and that, whenever the system is in, or close to, a singularity, the steering law drives the system state out of the vicinity of the singularity.

Yoshikawa, T.↗
NASA NTRS1975

Steering law for parallel mounted double-gimbaled control moment gyros

Parallel mounting of double-gimbaled control moment gyros (DG CMG) is discussed in terms of simplification of the steering law. The steering law/parallel mounted DG CMG is considered to be a 'CMG kit' applicable to any space vehicle where the need for DG CMG's has been established.

Kennel, H. F.↗
NASA NTRS1975

Large space telescope control moment gyro test program

The underlying theory and design of test instrumentation and computer techniques used to determine the power spectral density (PSD) of the third generation gyro are described in detail. Acceptance test results on the completed instrument are presented as well as composite PSD plots. The measured RMS noise over the frequency band 0.0025 - 10 Hz was 0.012 arc seconds. Results obtained at Martin Company indicate an RMS noise of 0.009 arc seconds (0.05 - 10 Hz). The results obtained showed the TGG performance was close to the proposed LST requirements but that additional development work would be needed to reduce the TGG noise to within more desirable limits.

Salamin, E.↗
NASA NTRS1976

Failure detection and isolation investigation for strapdown skew redundant tetrad laser gyro inertial sensor arrays

The degree to which flight-critical failures in a strapdown laser gyro tetrad sensor assembly can be isolated in short-haul aircraft after a failure occurrence has been detected by the skewed sensor failure-detection voting logic is investigated along with the degree to which a failure in the tetrad computer can be detected and isolated at the computer level, assuming a dual-redundant computer configuration. The tetrad system was mechanized with two two-axis inertial navigation channels (INCs), each containing two gyro/accelerometer axes, computer, control circuitry, and input/output circuitry. Gyro/accelerometer data is crossfed between the two INCs to enable each computer to independently perform the navigation task. Computer calculations are synchronized between the computers so that calculated quantities are identical and may be compared. Fail-safe performance (identification of the first failure) is accomplished with a probability approaching 100 percent of the time, while fail-operational performance (identification and isolation of the first failure) is achieved 93 to 96 percent of the time.

Eberlein, A. J.↗
NASA NTRS1975

Test evaluation of the Sperry laser gyro model ASLG 15

Various parameters were evaluated such as bias, scale factor, scale factor sensitivity to supply voltage and external temperature, and turn-on trends. Photographs and descriptions of test equipment are given, and test procedures are outlined. A systems description (electronic equipment, block diagrams), performance characteristics, and equipment specifications of the laser gyro model are given. Also considered are the laser beam optics (laser mode locking). Results are reported for the various parameters examined, and recommendations given.

Source record↗
NASA NTRS1978

Steering laws for double-gimbal control-moment gyros

Derivation of CMG steering laws was considered. The type of CMG considered was a double gimbal one which has a constant magnitude momentum vector. The equations for the generation of torque of an inertially fixed CMG are presented. To realize a particular commanded torque, the gimbal rates of the CMG must be specified. These gimbal rates are shown to be functions of gimbal angle orientation and the commanded torque. The conventional cross-product steering law was derived by minimizing a function which was the square of the magnitude of the error between the commanded torque and the realizable torque of the gyro. This steering law was severely dependent upon the inner gimbal angle. When the inner gimbal reaches 90 degrees, the cross product law requires infinite outer gimbal rates to realize finite torque values.

Winder, S. W.↗
NASA NTRS1979

Ground attitude determination and gyro calibration procedures for the HEAO missions

The Attitude Ground Support System (AGSS) at Goddard Space Flight Center provides ground attitude support for the High Energy Astronomy Observatory (HEAO) missions. The AGSS uses information telemetered from sun sensors, gyroscopes, star trackers (STAs), and an onboard computer to calculate updates to the onboard attitude reference and gyro calibration parameters. This paper presents the procedures used by the AGSS in computing reference and calibration updates; it also provides HEAO-1 postlaunch statistics that illustrate the ability to maintain 0.25-deg accuracy in the onboard attitude reference. Simulated HEAO-B results show an improvement in reference accuracy through the use of calibration maneuvers.

Fallon, L., III↗
NASA NTRS1979

Gyro precession and Mach's principle

The precession of a gyroscope is calculated in a nonrelativistic theory due to Barbour which satisfies Mach's principle. It is shown that the theory predicts both the geodetic and motional precession of general relativity to within factors of order 1. The significance of the gyro experiment is discussed from the point of view of metric theories of gravity and this is contrasted with its significance from the point of view of Mach's principle.

Eby, P.↗
NASA NTRS1980

A microprocessor application to a strapdown laser gyro navigator

The replacement of analog circuit control loops for laser gyros (path length control, cross axis temperature compensation loops, dither servo and current regulators) with digital filters residing in microcomputers is addressed. In addition to the control loops, a discussion is given on applying the microprocessor hardware to compensation for coning and skulling motion where simple algorithms are processed at high speeds to compensate component output data (digital pulses) for linear and angular vibration motions. Highlights are given on the methodology and system approaches used in replacing differential equations describing the analog system in terms of the mechanized difference equations of the microprocessor. Standard one for one frequency domain techniques are employed in replacing analog transfer functions by their transform counterparts. Direct digital design techniques are also discussed along with their associated benefits. Time and memory loading analyses are also summarized, as well as signal and microprocessor architecture. Trade offs in algorithm, mechanization, time/memory loading, accuracy, and microprocessor architecture are also given.

Giardina, C.↗
NASA NTRS1981

Steering law for parallel mounted double-gimbaled control moment gyros. Revision A

Mounting of double-gimbaled control moment gyros (CMG's) of unlimited outer gimbal angle freedom with all their outer gimbal axes parallel allows drastic simplification of the CMG steering law development hardware. The advantages of the parallel mounting for the CMG steering law development are such that a law could be developed which is applicable to any number of CMG's with arbitrary angular momentum. Parallel mounting of the CMG's in conjunction with the steering law can therefore be considered a CMG kit suitable for many missions of differing momentum requirements. It also means that increasing momentum demands during the design phase of a space vehicle can be easily met by the addition of one or more CMG's of the original momentum capacity rather than a redesign to a larger momentum capacity. Another advantage of the parallel mounting is that the failure of any CMG can be treated like any other, i.e., only one failure mode is possible. The CMG steering law distributes the CMG momentum vectors such that all inner gimbal angles are equal which reduces the rate requirements on the outer gimbal axes. The steering law also spreads the outer gimbals which ensures avoidance of singularities internal to the angular momentum envelope.

Kennel, H. F.↗
NASA NTRS1982

Guidance and flight control demonstration in a helicopter flight environment using a laser-gyro inertial navigation system

The present flight test program results indicate that an all-digital inertial sensing system can be used in helicopter flight guidance and control, provided that the rotor rotation-induced motions are filtered from body rate and accelerometer signals before they are used in the feedback control system. Attention is given to the problem posed by the different repetition rates used by each of the manufacturers involved in the procurement of such all-digital subsystems. Autopilot designers must accordingly predict the need for filters and install them where called for in the sensor software. Two alternatives to this method are explored. Recent technological developments indicate that strapped down inertial systems will replace vertical and direction gyros as well as body rate accelerometers in future aircraft systems.

Schmidt, S. F.↗