Search NASA⌕ Search

SEARCH · Search NASA

Results for “humidity sensing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

All-aerosol-jet-printed highly sensitive and selective polyaniline-based ammonia sensors: a route toward low-cost, low-power gas detection

In this work, we report the design and scalable fabrication of a low-cost and low-power polyaniline-based (PANI) ammonia (NH3) gas sensor on polyimide (PI) substrates using additive manufacturing techniques. The silver interdigitated electrode (IDE) arrays and conducting polymer films are printed onto PI using a direct-write technology of aerosol-jet printing. Morphological characteristics are examined by scanning electron microscopy and energy-dispersive X-ray analysis which reveal homogeneously printed PANI film on the IDE platform. The gas sensing performance is evaluated in the analytical early leak detection range of 5–1000 ppm NH3 in air as a function of both thermal (23 °C, 50 °C, 80 °C) and relative humidity (RH = 0%, 30%, 50%) exposures. The sensor exhibits sensitivity down to 5 ppm NH3 with a sub-ppm detection limit and good repeatability. We observe rapid NH3 detection at 0% RH with very extended times for equilibration and recovery. However, at both 30 and 50% RH, the room temperature response and recovery times are reduced to only about 1 min and 5 min, respectively. Experiments also reveal good sensitivity toward the analyte even at higher operating temperatures. Present results merit the practical application of aerosol-jet-printed, low-power sensors for industrial applications where low-level hazardous gas detection is essential.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Low level remote sensing: Orographic winds

The orographic flow data set was obtained from a flight program to measure the influence of orographic features on turbulence momentum, heat, and moisture fluxes. The NASA B-57 aircraft instrumented with probes for measuring the three fluctuating wind speed components, temperature, and humidity was the primary measuring vehicle. Ancillary measurements were made with several ground-based sensors. These include the NOAA radar wind profilers, the Boulder wind network, the PROFS mesoscale surface network, the Boulder Atmospheric Observatory 300 m tower, special rawinsonde observations, and the NOAA/WPL Doppler lidar. The major objective of the flight program was to provide planetary boundary layer parameter information for new and current general circulation computer models. A numerical code, WINDER, based on a discrete element technique was run to numerically model the water tunnel simulated flow. Comparison of the analytical model with the experimental results is very good. Physical fluid dynamic principles embedded in the computational model and visual and hot wire anemometer measurements from the simulation are being rationalized to develop a physical understanding of the vortex flow. The results will be interpreted as they pertain to full scale atmospheric flows.

Frost, Walter↗
NASA NTRS1978

In-place recalibration technique applied to a capacitance-type system for measuring rotor blade tip clearance

The rotor blade tip clearance measurement system consists of a capacitance sensing probe with self contained tuning elements, a connecting coaxial cable, and remotely located electronics. Tests show that the accuracy of the system suffers from a strong dependence on probe tip temperature and humidity. A novel inplace recalibration technique was presented which partly overcomes this problem through a simple modification of the electronics that permits a scale factor correction. This technique, when applied to a commercial system significantly reduced errors under varying conditions of humidity and temperature. Equations were also found that characterize the important cable and probe design quantities.

Barranger, J. P.↗
NASA NTRS1980

Using Landsat digital data to detect moisture stress in corn-soybean growing regions

As a part of a follow-on study to the moisture stress detection effort conducted in the Large Area Crop Inventory Experiment (LACIE), a technique utilizing transformed Landsat digital data was evaluated for detecting moisture stress in humid growing regions using sample segments from Iowa, Illinois, and Indiana. At known growth stages of corn and soybeans, segments were classified as undergoing moisture stress or not undergoing stress. The remote-sensing-based information was compared to a weekly ground-based index (Crop Moisture Index). This comparison demonstrated that the remote sensing technique could be used to monitor the growing conditions within a region where corn and soybeans are the major crop.

Thompson, D. R.↗
NASA NTRS2010

Verification Challenges of Dynamic Testing of Space Flight Hardware

The Six Degree-of-Freedom Dynamic Test System (SDTS) is a test facility at the National Aeronautics and Space Administration (NASA) Johnson Space Center in Houston, Texas for performing dynamic verification of space structures and hardware. Some examples of past and current tests include the verification of on-orbit robotic inspection systems, space vehicle assembly procedures and docking/berthing systems. The facility is able to integrate a dynamic simulation of on-orbit spacecraft mating or demating using flight-like mechanical interface hardware. A force moment sensor is utilized for input to the simulation during the contact phase, thus simulating the contact dynamics. While the verification of flight hardware presents many unique challenges, one particular area of interest is with respect to the use of external measurement systems to ensure accurate feedback of dynamic contact. There are many commercial off-the-shelf (COTS) measurement systems available on the market, and the test facility measurement systems have evolved over time to include two separate COTS systems. The first system incorporates infra-red sensing cameras, while the second system employs a laser interferometer to determine position and orientation data. The specific technical challenges with the measurement systems in a large dynamic environment include changing thermal and humidity levels, operational area and measurement volume, dynamic tracking, and data synchronization. The facility is located in an expansive high-bay area that is occasionally exposed to outside temperature when large retractable doors at each end of the building are opened. The laser interferometer system, in particular, is vulnerable to the environmental changes in the building. The operational area of the test facility itself is sizeable, ranging from seven meters wide and five meters deep to as much as seven meters high. Both facility measurement systems have desirable measurement volumes and the accuracies vary within the respective volumes. In addition, because this is a dynamic facility with a moving test bed, direct line-of-sight may not be available at all times between the measurement sensors and the tracking targets. Finally, the feedback data from the active test bed along with the two external measurement systems must be synchronized to allow for data correlation. To ensure the desired accuracy and resolution of these systems, calibration of the systems must be performed regularly. New innovations in sensor technology itself are periodically incorporated into the facility s overall measurement scheme. In addressing the challenges of the measurement systems, the facility is able to provide essential position and orientation data to verify the dynamic performance of space flight hardware.

Winnitoy, Susan↗
NASA NTRS1973

Lidar Measurements of the Thermic Structure in the Troposphere

Lidar measurements by UTHE (1972) and similar measurements with acoustic radar by HALL (1972) have shown, that short time variations in the troposphere can be determined. Aerosol backscatter measurements give the vertical structure. A series of such results shows the time variation of the tropospheric structure. The Figure is an example for a measuring period during half an hour in summer 1972 (1 pulse per minute). These variations were produced by humidity variations. For example, at humidity variations from 75% to 77% aerosol particles with 1 micron radius change their radii during 50 to 100 milliseconds. By lidar technique it is possible to determine this effect qualitatively. With a pulse repetition rate of 1 per second we plan to investigate the thermic structure at different weather conditions. By simultaneous measurements of the nitrogen Raman component it would be possible to compare the short time variations by temperature and humidity. The influence of wind can be determined by scanning a defined region (region or space). The meteorologist is interested in results of short time variations in the troposphere (microscale). By this remote sensing method he can get these values continuously.

Werner, Ch.↗
NASA NTRSDate not supplied

Ice-Over-Water Cloud Properties in an Artificial Neural Network Approach

Clouds are a crucial component of the atmospheric energy system, particularly the radiative balance within, above, and below the troposphere. The vertical distribution of cloud mass and phase determines layer heating rates, the loss of radiation to space, and the amount of radiative heating at the surface. Thus, it is important to know how clouds are distributed both vertically and horizontally at all times of day. Satellite remote sensing is the only approach available to monitor clouds day and night around the globe. In this paper several artificial neural network (ANN) algorithms, employing several Aqua MODIS infrared channels, profiles of relative humidity and temperature from GMAO numerical weather analyses, and the retrieved total cloud visible optical depth, are trained to detect multilayer ice-over-water cloud systems and to retrieve some of their properties as identified by a year of 2008 Aqua MODIS data matched with CloudSat and CALIPSO (CC) cloud profiles. The CC lidar and radar profiles provide the vertical structure that serves as output truth for the multilayer algorithm. The neural networks were trained using one year (2008) of cloud top height data from the CC dataset, with correlation around 0.94 (0.95) and MAE as low as 0.82 (0.81) km for nonpolar regions during the day (night). Applying the trained ANN to independent year 2009 MODIS data resulted in a combined ML and single layer hit rate of 86.4% (85.1%) for nonpolar regions during the day (night). Since the ANN is trained using near-nadir MODIS pixels, infrared radiance corrections were developed as a function of view zenith angle from MODIS and applied to off-nadir pixels when processing MODIS swath data. The multilayer amount derived with the ANN is relatively invariant with increasing view zenith angle compared to the multilayer amount without the corrections.

MODIS↗
DOE OSTI2026

Field and Model Data Associated with the Manuscript “Drivers of Streamflow Intermittency in Humid Regions: 2. Evaluating Controls on Flow Persistence in an Urbanized Catchment”

This package contains field data, modeling files, and scripts supporting the investigation of the drivers of streamflow intermittency in an urbanized catchment. It includes the field data collected from electrical resistivity tomography (ERT) surveys, distributed temperature sensing (DTS), continuous self-potential (SP) monitoring, groundwater and stilling well. In addition, it contains the data and results of the coupled water- and electrical-flow model developed using the COMSOL Multiphysics and Advanced Terrestrial Simulator (ATS), as well as software files and Jupyter notebooks used to process the data and generate figures in the manuscript submitted for peer review. The data archive is organized in the following directories: 1) Climate Includes hourly precipitation and daily evapotranspiration time series (2024 – 2025) provided as CSV files, alongside a text file detailing dataset units. 2) Coupled_model Field_Application subfolder contains the ATS XML input scripts, data files, output data for the SP site. It also contains the Jupyter notebook (Plot_final_calib.ipynb) to visualize the results of the modeled SP, stream-groundwater exchange and moisture content. The flow model simulation is executed using the ATS XML scripts and the included Python script (generate_data_set.py) to convert ATS output to COMSOL-ready input. COMSOL Multiphysics template (.m can only be used with COMSOL with MATLAB) is executed using the ATS output data to simulate the potential field. 3) Discharge Includes the electrical conductivity (EC) time series (provided as CSV files) from salt slug injections. It also includes the Jupyter notebook (Discharge_process.ipynyb) used to estimate discharge. All discharge measurements collated into rating_curve_processed.csv 4) DTS Contains collated DTS data including raw Stokes and anti-Stokes measurement (provided as .h5 file). It also includes DTS processing.ipynb, a Jupyter notebook for calibrating the DTS data using dts_calibration Python package. cooler_calibration.csv is the DTS calibration CSV used in the calibration sequence. 5) ERT Contains raw resistivity data (provided as CSV files), spatial location of each of the electrodes (provided as CSV files), and files used for the resistivity inversion. 6) Slug_test Includes the slug test data at all the groundwater wells provided as CSV files, as well as the Jupyter notebook (Slug_test.ipynb) for calculating hydraulic conductivity. 7) SP Contains the SP data collected in field at the SP sites (provided as CSV files). 8) Well_data Contains two subfolders: 1) Raw, which provides unprocessed pressure, electrical conductivity and temperature timeseries downloaded from the loggers in all the groundwater and stilling wells, and 2) Processed, which contains sorted, QA/QC timeseries data for each well. The data archive also contains data_process.ipynb, a Jupyter notebook used for field data analysis and generating figures (plotting well, SP, climate, and discharge data, as well as calculating head gradient at sites with nested groundwater wells). Note: Code files (.ipynb, .py, .xml) can be opened in any standard code editor, .exo file can be viewed using Paraview, .h5 files can be opened using HDFView software and h5py Python package, and .resipy file can be opened with the open-source ResIPy software.

ATS↗
NASA NTRS2006

Use of In Situ Cloud Condensation Nuclei, Extinction, and Aerosol Size Distribution Measurements to Test a Method for Retrieving Cloud Condensation Nuclei Profiles From Surface Measurements

If the aerosol composition and size distribution below cloud are uniform, the vertical profile of cloud condensation nuclei (CCN) concentration can be retrieved entirely from surface measurements of CCN concentration and particle humidification function and surface-based retrievals of relative humidity and aerosol extinction or backscatter. This provides the potential for long-term measurements of CCN concentrations near cloud base. We have used a combination of aircraft, surface in situ, and surface remote sensing measurements to test various aspects of the retrieval scheme. Our analysis leads us to the following conclusions. The retrieval works better for supersaturations of 0.1% than for 1% because CCN concentrations at 0.1% are controlled by the same particles that control extinction and backscatter. If in situ measurements of extinction are used, the retrieval explains a majority of the CCN variance at high supersaturation for at least two and perhaps five of the eight flights examined. The retrieval of the vertical profile of the humidification factor is not the major limitation of the CCN retrieval scheme. Vertical structure in the aerosol size distribution and composition is the dominant source of error in the CCN retrieval, but this vertical structure is difficult to measure from remote sensing at visible wavelengths.

Ghan, Stephen J.↗
NASA NTRS2015

Initial Results from Radiometer and Polarized Radar-Based Icing Algorithms Compared to In-Situ Data

In early 2015, a field campaign was conducted at the NASA Glenn Research Center in Cleveland, Ohio, USA. The purpose of the campaign is to test several prototype algorithms meant to detect the location and severity of in-flight icing (or icing aloft, as opposed to ground icing) within the terminal airspace. Terminal airspace for this project is currently defined as within 25 kilometers horizontal distance of the terminal, which in this instance is Hopkins International Airport in Cleveland. Two new and improved algorithms that utilize ground-based remote sensing instrumentation have been developed and were operated during the field campaign. The first is the 'NASA Icing Remote Sensing System', or NIRSS. The second algorithm is the 'Radar Icing Algorithm', or RadIA. In addition to these algorithms, which were derived from ground-based remote sensors, in-situ icing measurements of the profiles of super-cooled liquid water (SLW) collected with vibrating wire sondes attached to weather balloons produced a comprehensive database for comparison. Key fields from the SLW-sondes include air temperature, humidity and liquid water content, cataloged by time and 3-D location. This work gives an overview of the NIRSS and RadIA products and results are compared to in-situ SLW-sonde data from one icing case study. The location and quantity of super-cooled liquid as measured by the in-situ probes provide a measure of the utility of these prototype hazard-sensing algorithms.

flight test↗
DOE OSTI2024

Science Area 1: Standard Award: Model-Data Fusion to Examine Multiscale Dynamical Controls on Snow Cover and Critical Zone Moisture Inputs (Final Report)

In many mountain watersheds of the world, seasonal snowpacks play an important role as natural reservoirs of water. Seasonal snowpacks accumulate water during cold, wet winter months that subsequently melts. Downstream communities depend on water from melting seasonal snowpacks to support agricultural, industrial, and municipal water needs. Rapidly melting snowpacks can also present a flooding hazard, particularly if snowpacks melt at rates faster than anticipated and where adequate reservoir capacity is unavailable to buffer river flows associated with melt. The spatial and temporal dynamics of snow accumulation and melt also play an important role in supporting upland ecosystems in mountain landscapes. Snowmelt provides soil moisture that enable terrestrial ecosystem productivity and exert control on soil microorganisms that play important roles in global carbon cycles. Climate warming is gradually decreasing the amount of precipitation in mountain watersheds arriving as snow, presenting potentially profound disruptions to mountain ecosystems, as well as downstream delivery of water. The overarching goal of this project was to understand how interactions between the near-surface atmosphere and surface topography control the input, accumulation, retention, and release of water from mountain snowpacks. Over a 5-year period, this project pursued an approach combining high-resolution regional climate modeling, satellite and airborne remote sensing data, and ground-based observations to develop and analyze benchmark datasets to address overarching science questions and hypotheses. Key products include a continuous, long-term, high spatiotemporal resolution (1 km/1 hr) dataset characterizing key climate variables in the Upper Colorado River Basin. The dataset included historical estimates of precipitation, temperature, humidity, solar and longwave radiation, and wind speeds. Additionally, the project developed a 20+ year long, 30 m spatial, daily temporal multi-sensor dataset characterizing snow presence/absence in the East/Taylor River watersheds in the Central Rocky Mountains of Colorado. The project supported training of 1 postdoctoral scholar, 1 Ph.D. student, and 1 M.S. student.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1979

Microwave sensing from orbit

Microwave sensors, used in conjunction with the traditional sensors of visible and infrared light to extend present capabilities of global weather forecasts and local storm watches, are discussed. The great advantage of these sensors is that they can penetrate or 'see' through cloud formations to monitor temperature, humidity and wind fields below the clouds. Other uses are that they can penetrate the earth deeper than optical and IR systems; they can control their own angle of incidence; they can detect oil spills; and they can enhance the studies of the upper atmosphere through measurement of temperature, water vapor and other gaseous species. Two types of microwave sensors, active and passive, are examined. Special attention is given to the study of the microwave radiometer and the corresponding temperature resolution as detected by the antenna. It is determined that not only will the microwave remote sensors save lives by allowing close monitoring of developing storms, but also save approximately $172 million/year.

Kritikos, H. N.↗
NASA NTRS1986

Remote sensing of cloud distributions over the Bayanhar Mountains - Watershed of the Yangtze and Yellow rivers

Although the two largest rivers in China originate in the same region separated only by the Bayanhar Mountains as a watershed, the Yangtze and Yellow rivers behave in quite different ways. Most of the warm and humid air currents from the Arabian sea and the Bay of Bengal are blocked by the Bayanhar Mountains. As a result the amount of water in the Yellow River is only 5 percent of that in the Yangtze river. Based on the cloud coverage area and the cloud volumetric distributions, and also the thickness above 9.4 km of the cumulus clouds located north and south of the Bayanhar Mountains from the geosynchronous satellite infrared imagery, the results suggest that a more detailed investigation is warranted in the hope that the proper modification of cumuli north of the Bayanhar Mountains would enhance the rainfall over the fountainhead of the Yellow River.

Hung, R. J.↗
NASA NTRS2016

Multi-Sensor Cloud and Aerosol Retrieval Simulator and Remote Sensing from Model Parameters : Aerosols - Part 2

The Multi-sensor Cloud Retrieval Simulator (MCRS) produces a simulated radiance product from any high-resolution general circulation model with interactive aerosol as if a specific sensor such as the Moderate Resolution Imaging Spectroradiometer (MODIS) were viewing a combination of the atmospheric column and land ocean surface at a specific location. Previously the MCRS code only included contributions from atmosphere and clouds in its radiance calculations and did not incorporate properties of aerosols. In this paper we added a new aerosol properties module to the MCRS code that allows users to insert a mixture of up to 15 different aerosol species in any of 36 vertical layers. This new MCRS code is now known as MCARS (Multi-sensor Cloud and Aerosol Retrieval Simulator). Inclusion of an aerosol module into MCARS not only allows for extensive, tightly controlled testing of various aspects of satellite operational cloud and aerosol properties retrieval algorithms, but also provides a platform for comparing cloud and aerosol models against satellite measurements. This kind of two-way platform can improve the efficacy of model parameterizations of measured satellite radiances, allowing the assessment of model skill consistently with the retrieval algorithm. The MCARS code provides dynamic controls for appearance of cloud and aerosol layers. Thereby detailed quantitative studies of the impacts of various atmospheric components can be controlled. In this paper we illustrate the operation of MCARS by deriving simulated radiances from various data field output by the Goddard Earth Observing System version 5 (GEOS-5) model. The model aerosol fields are prepared for translation to simulated radiance using the same model sub grid variability parameterizations as are used for cloud and atmospheric properties profiles, namely the ICA technique. After MCARS computes modeled sensor radiances equivalent to their observed counterparts, these radiances are presented as input to operational remote-sensing algorithms. Specifically, the MCARS-computed radiances are input into the processing chain used to produce the MODIS Data Collection 6 aerosol product (MOYD04). TheMOYD04 product is of course normally produced from MOYD021KM MODIS Level-1B radiance product directly acquired by the MODIS instrument. MCARS matches the format and metadata of a MOYD021KM product. The resulting MCARS output can be directly provided to MODAPS (MODIS Adaptive Processing System) as input to various operational atmospheric retrieval algorithms. Thus the operational algorithms can be tested directly without needing to make any software changes to accommodate an alternative input source. We show direct application of this synthetic product in analysis of the performance of the MOD04 operational algorithm. We use biomass-burning case studies over Amazonia employed in a recent Working Group on Numerical Experimentation (WGNE)-sponsored study of aerosol impacts on numerical weather prediction (Freitas et al., 2015). We demonstrate that a known low bias in retrieved MODIS aerosol optical depth appears to be due to a disconnect between actual column relative humidity and the value assumed by the MODIS aerosol product.

aerosol retrieval↗
NASA NTRS2022

Leveraging Pre-storm Soil Moisture Estimates for Enhanced Land Surface Model Calibration in Ungauged Hydrologic Basins

Despite long-standing efforts, hydrologists still lack robust tools for calibrating land surface model (LSM) streamflow estimates within ungauged basins. Using surface soil moisture estimates from the Soil Moisture Active Passive Level 4 Soil Moisture (L4_SM) product, precipitation observations, and streamflow gauge measurements for 617 medium-scale (200-10,000 km2) basins in the contiguous United States, we measure the temporal (Spearman) rank correlation between antecedent (i.e., pre-storm) surface soil moisture (ASM) and the storm-scale runoff coefficient (RC; the fraction of storm-scale precipitation accumulation converted into streamflow). In humid and semi-humid basins, this rank correlation is shown to be sufficiently strong to allow for the substitution of storm-scale RC observations (available only in basins that are both lightly regulated and gauged) with high-quality ASM values (available quasi-globally from L4_SM) in streamflow calibration procedures. Using this principle, we define a new, basin-wise LSM streamflow calibration approach based on L4_SM alone and successfully apply it to identify LSM configurations that produce a high rank correlation with observed RC. However, since the approach cannot detect RC bias, it is less successful in identifying LSM configurations with low mean-absolute error. Plain Text Summary Accurately forecasting the fraction of rainfall that runs off into streams, as opposed to infiltrates into the soil, is critical for flash-flood prediction, water-resource monitoring, and tracking the transport of nutrients from agricultural fields into local waterways. Such forecasting is typically performed by hydrologic models that attempt to represent the physical processes responsible for surface runoff generation. However, to provide accurate streamflow forecasts, these models typically need to be calibrated against actual streamflow observations. This is problematic given the relatively poor, and declining, global availability of stream gauges. This paper presents a novel model calibration strategy that uses soil moisture from remote sensing and numerical modeling in place of streamflow observations during calibration. This transition has significant practical advantages because, unlike streamflow observations, the soil moisture data are continuously available across space. Our results demonstrate that this new approach can significantly improve hydrologic models within humid and semi-humid basins lacking sufficient ground-based instrumentation for traditional streamflow calibration.

hydrologic models↗
DOE OSTI2024

An Impedance-Loaded Surface Acoustic Wave Corrosion Sensor for Infrastructure Monitoring

Passive surface acoustic wave (SAW) devices are attractive candidates for continuous wireless monitoring of corrosion in large infrastructures. However, acoustic loss in the aqueous medium and limited read range usually create challenges in their widespread use for monitoring large systems such as oil and gas (O&G) pipelines, aircraft, and processing plants. This paper presents the investigation of impedance-loaded reflective delay line (IL-RDL) SAW devices for monitoring metal corrosion under O&G pipeline-relevant conditions. Specifically, we studied the effect of change in resistivity of a reflector on the backscattered signal of an RDL and investigated an optimal range through simulation. This was followed by the experimental demonstrations of real-time monitoring of Fe film corrosion in pressurized (550 psi) humid CO 2 conditions. Additionally, remote monitoring of Fe film corrosion in an acidic solution inside a 70 m carbon steel pipe was demonstrated using guided waves. This paper also suggests potential ways to improve the sensing response of IL-RDLs.

47 OTHER INSTRUMENTATION↗
NASA NTRS1992

Optical fiber sensors for life support applications

Preliminary experimental results on systems designed to demonstrate sensor operation in regenerative food production and crew air supply applications are presented. The systems use conventional fibers and sources in conjunction with custom wavelength division multiplexers in their optical signal processing sections and nonstandard porous optical fibers in the optical sensing elements. It is considered to be possible to create practical sensors for life-support system applications, and particularly, in regenerative food production environments, based on based on reversible sensors for oxygen, carbon monoxide, and humidity.

Lieberman, R. A.↗