SEARCH · Search NASA

Results for “interior point”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1990

Noise transmission characteristics of a large scale composite fuselage model

Results from an experimental test undertaken to study the basic noise transmission characteristics of a realistic, built-up composite fuselage model are presented. The floor-equipped stiffened composite cylinder was exposed to a number of different exterior noise source configurations in a large anechoic chamber. These exterior source configurations included two point sources located in the same plane on opposite sides of the cylinder, a single point source and a propeller simulator. The results indicate that the interior source field is affected strongly by exterior noise source phasing. Sidewall treatment is seen to reduce the overall interior sound pressure levels and dampen dominant acoustic resonances so that other acoustic modes can affect interior noise distribution.

Beyer, Todd B.↗

NASA NTRS2007

Iapetus' Geophysics: Rotation Rate, Shape, and Equatorial Ridge

Iapetus has preserved evidence that constrains the modeling of its geophysical history from the time of its accretion until now. The evidence is (a) its present 79.33-day rotation or spin rate, (b) its shape that corresponds to the equilibrium figure for a hydrostatic body rotating with a period of approximately 16 h, and (c) its high, equatorial ridge, which is unique in the Solar System. This paper reports the results of an investigation into the coupling between Iapetus' thermal and orbital evolution for a wide range of conditions including the spatial distributions with time of composition, porosity, short-lived radioactive isotopes (SLRI), and temperature. The thermal model uses conductive heat transfer with temperature-dependent conductivity. Only models with a thick lithosphere and an interior viscosity in the range of about the water ice melting point can explain the observed shape. Short-lived radioactive isotopes provide the heat needed to decrease porosity in Iapetus? early history. This increases thermal conductivity and allows the development of the strong lithosphere that is required to preserve the 16-h rotational shape and the high vertical relief of the topography. Long-lived radioactive isotopes and SLRI raise internal temperatures high enough that significant tidal dissipation can start, and despin Iapetus to synchronous rotation. This occurred several hundred million years after Iapetus formed. The models also constrain the time when Iapetus formed because the successful models are critically dependent upon having just the right amount of heat added by SLRI decay in this early period. The amount of heat available from short-lived radioactivity is not a free parameter but is fixed by the time when Iapetus accreted, by the canonical concentration of Al-26, and, to a lesser extent, by the concentration of Fe-60. The needed amount of heat is available only if Iapetus accreted between 2.5 and 5.0Myr after the formation of the calcium aluminum inclusions as found in meteorites. Models with these features allow us to explain Iapetus? present synchronous rotation, its fossil 16-h shape, and the context within which the equatorial ridge arose.

geophysics↗

NASA NTRS2016

Moonage Daydream: Reassessing the Simple Model for Lunar Magma Ocean Crystallization

Details of the differentiation of a global-scale lunar magma ocean (LMO) remain enigmatic, as the Moon is not simply composed of highlands anorthosite and a suite of mare basalts as inferred from early studies. Results from recent orbital missions, and the increasingly detailed study of lunar samples, have revealed a much larger range of lithologies, from relatively MgO-rich and "purest anorthosite" discovered on the lunar far side by the M3 instrument on Chandraayan-1 to more exotic lithologies such as Si-rich domes and spinel-rich clasts distributed globally. To understand this increasingly complex geology, we must understand the initial formation and evolution of the LMO, and the composition of the cumulates this differentiation could have produced. Several attempts at modelling such a crystallization sequence have been made, and have raised as many questions as they have answered. We present results from our ongoing experimental simulations of magma ocean crystallization, investigating two end-member bulk compositions (TWM and LPUM) under fully fractional crystallization conditions. These simulations represent melting of the entire silicate portion of the Moon, as an end-member starting point from which to begin assessing the evolution of the lunar interior and formation of the lunar crust.

Rapp, J. F.↗

NASA NTRS1975

Multispectral processing based on groups of resolution elements

Several nine-point rules are defined and compared with previously studied rules. One of the rules performed well in boundary areas, but with reduced efficiency in field interiors; another combined best performance on field interiors with good sensitivity to boundary detail. The basic threshold gradient and some modifications were investigated as a means of boundary point detection. The hypothesis testing methods of closed-boundary formation were also tested and evaluated. An analysis of the boundary detection problem was initiated, employing statistical signal detection and parameter estimation techniques to analyze various formulations of the problem. These formulations permit the atmospheric and sensor system effects on the data to be thoroughly analyzed. Various boundary features and necessary assumptions can also be investigated in this manner.

Richardson, W.↗

NASA NTRS1990

Measurement of horizontal motions in Alaska using very long baseline interferometry

Results are presented on an analysis of VLBI measurements performed between 1984 and 1990 by means of a network of 53 sites in Alaska, the Yukon Territory, and the conterminous United States to determine the extent of horizontal motions in Alaska. Results are presented in two ways, one showing the evolution of individual baselines and the other yielding site velocities; both approaches use VLBI data from other permanent stations in order to define a global reference frame. It was found that VLBI sites within the Alaska-Aleutian subduction boundary zone (Yakataga, Kodiak, and Sand Point) had higher instantaneous velocities relative to eastern North America than the interior sites of Alaska. The results of Yakataga data modeling suggests that the observed motion is the result of elastic straining of the overriding plate due to a locked main thrust zone with a component of oblique slip.

Ma, C.↗

NASA NTRS1997

The Reduction of Ducted Fan Engine Noise Via A Boundary Integral Equation Method

The development of a Boundary Integral Equation Method (BIEM) for the prediction of ducted fan engine noise is discussed. The method is motivated by the need for an efficient and versatile computational tool to assist in parametric noise reduction studies. In this research, the work in reference 1 was extended to include passive noise control treatment on the duct interior. The BEM considers the scattering of incident sound generated by spinning point thrust dipoles in a uniform flow field by a thin cylindrical duct. The acoustic field is written as a superposition of spinning modes. Modal coefficients of acoustic pressure are calculated term by term. The BEM theoretical framework is based on Helmholtz potential theory. A boundary value problem is converted to a boundary integral equation formulation with unknown single and double layer densities on the duct wall. After solving for the unknown densities, the acoustic field is easily calculated. The main feature of the BIEM is the ability to compute any portion of the sound field without the need to compute the entire field. Other noise prediction methods such as CFD and Finite Element methods lack this property. Additional BIEM attributes include versatility, ease of use, rapid noise predictions, coupling of propagation and radiation both forward and aft, implementable on midrange personal computers, and valid over a wide range of frequencies.

Tweed, J.↗

NASA NTRS2011

Evaluation of the Global Multi-Resolution Terrain Elevation Data 2010 (GMTED2010) Using ICESat Geodetic Control

Supported by NASA's Earth Surface and Interior (ESI) Program, we are producing a global set of Ground Control Points (GCPs) derived from the Ice, Cloud and land Elevation Satellite (ICESat) altimetry data. From February of 2003, to October of 2009, ICESat obtained nearly global measurements of land topography (+/- 86deg latitudes) with unprecedented accuracy, sampling the Earth's surface at discrete approx.50 m diameter laser footprints spaced 170 m along the altimetry profiles. We apply stringent editing to select the highest quality elevations, and use these GCPs to characterize and quantify spatially varying elevation biases in Digital Elevation Models (DEMs). In this paper, we present an evaluation of the soon to be released Global Multi-resolution Terrain Elevation Data 2010 (GMTED2010). Elevation biases and error statistics have been analyzed as a function of land cover and relief. The GMTED2010 products are a large improvement over previous sources of elevation data at comparable resolutions. RMSEs for all products and terrain conditions are below 7 m and typically are about 4 m. The GMTED2010 products are biased upward with respect to the ICESat GCPs on average by approximately 3 m.

Carabajal, Claudia C.↗

NASA NTRS1992

Active control of interior noise in a large scale cylinder using piezoelectric actuators

The noise reduction effectiveness of two types of control force actuator models has been analytically investigated: (1) a point actuator, and (2) an in-plane, piezoelectric actuator. The actuators were attached to the wall of a simply supported, elastic cylinder closed with rigid end caps. Control inputs to the actuators were determined such that the integrated square of the pressure over the interior of the vibrating cylinder was a minimum. Significant interior noise reductions were achieved for all actuator configurations, but especially for the structurally dominated response. Noise reduction of 9 dB to 26 dB were achieved using point force actuators, as well as localized and extended piezoelectric actuators. Control spillover was found to limit overall performance for all cases. However, the use of extended piezoelectric actuators was effective in reducing control spillover, without increasing the number of control degrees of freedom.

Lester, H. C.↗

NASA NTRS1991

Active control of interior noise in a large scale cylinder using piezoelectric actuators

Lester, H. C.↗

NASA NTRS1998

Mechanical Properties of Degraded PMR-15 Resin

Thermo-oxidative aging produces a non-uniform degradation state in PMR-15 resin. A surface layer, usually attributed to oxidative degradation, forms. This surface layer has different properties from the inner material. A set of material tests was designed to separate the properties of the oxidized surface layer from the properties of interior material. Test specimens were aged at 316 C in either air or nitrogen, for durations of up to 800 hours. The thickness of the oxidized surface layer in air aged specimens, and the shrinkage and Coefficient of Thermal Expansion (CTE) of nitrogen aged specimens were measured directly. Four-point-bend tests were performed to determine modulus of both the oxidized surface layer and the interior material. Bimaterial strip specimens consisting of oxidized surface material and unoxidized interior material were constructed and used to determine surface layer shrinkage and CTE. Results confirm that the surface layer and core materials have substantially different properties.

Tsuji, Luis C.↗

NASA NTRS1978

An experimental map of the internal structure of a vortex breakdown

The flow field of an 'axisymmetric' vortex breakdown has been mapped using a laser-Doppler anemometer. The interior of the recirculation zone is dominated by energetic, non-axisymmetric, low frequency periodic fluctuations. Spectra for a number of points inside this zone, as well as time-averaged swirl and axial velocity profiles both inside and outside the recirculation zone, have been obtained. The time-averaged streamlines in the interior show an unexpected two-celled structure attributed to the action of the fluctuations. Although the present experiment deals with one particular breakdown, flow-visualization studies indicate that the case examined is typical of the 'axisymmetric' form of breakdown over a range of flow conditions.

Faler, J. H.↗

NASA NTRS1977

A new source of lunar electromagnetic induction - Forcing by the diamagnetic cavity

Analysis of the power spectral densities (PSD's) of eight 50-hour time series from Apollo 12 lunar surface magnetometer (LSM) and isochronous Explorer 35 Ames magnetometer data points to the existence of a new source of electromagnetic induction in the interior of the moon which is independent of the transverse electric mode. This source is hypothesized to arise from extension of the cavity diamagnetic field into the moon in analogy with the fringing field of a solenoid.

Sonett, C. P.↗

NASA NTRSDate not supplied

A Multi-Functional, Two-Chamber Airlock Node for a Common Habitat Architecture

An airlock is generally considered a necessity for any large, habitable spacecraft. While suitports, docked rovers, and external robotics can reduce the need for airlock operations, at some point it is necessary to move both crew and equipment from a habitat interior to the exterior environment. The Common Habitat is a large, long-duration habitat that uses the Space Launch System (SLS) Core Stage Liquid Oxygen tank as the primary structure (similar to Skylab) and has an internal architecture compatible with microgravity, lunar gravity, and Mars gravity, such that identical versions of the same design can be used in all three environments. It needs an airlock that is similarly appropriate for both surface and microgravity environments. After a brief survey of prior airlocks, the two-chamber node airlock concept applied to the Common Habitat architecture is described. This includes benefits of the dual chamber and node approaches, dimensions, hatches and docking ports, utilities connections, hatch covers, suit storage, EVA stowage, subsystems, and gravity-specific external attachments. Additionally, the functions of each chamber and reconfiguration capabilities are explained. Finally, conclusions and follow-on work are discussed.

Robert L Howard↗

NASA NTRS1993

Laplace's equation and the Dirichlet-Neumann map in multiply connected domains

A variety of problems in material science and fluid dynamics require the solution of Laplace's equation in multiply connected domains. Integral equation methods are natural candidates for such problems, since they discretize the boundary alone, require no special effort for free boundaries, and achieve superalgebraic convergence rates on sufficiently smooth domains in two space dimensions, regardless of shape. Current integral equation methods for the Dirichlet problem, however, require the solution of M independent problems of dimension N, where M is the number of boundary components and N is the total number of points in the discretization. In this paper, we present a new boundary integral equation approach, valid for both interior and exterior problems, which requires the solution of a single linear system of dimension N + M. We solve this system by making use of an iterative method (GMRES) combined with the last multipole method for the rapid calculation of the necessary matrix vector products. For a two-dimensional system with 200 components and 100 points on each boundary, we gain a speedup of a factor of 100 from the new analytic formulation and a factor of 50 from the fast multipole method. The resulting scheme brings large scale calculations in extremely complex domains within practical reach.

Greenbaum, A.↗

NASA NTRS1992

Coupling finite element and integral equation solutions using decoupled boundary meshes

A method is outlined for calculating scattered fields from inhomogeneous penetrable objects using a coupled finite element-integral equation solution. The finite element equation can efficiently model fields in penetrable and inhomogeneous regions, while the integral equation exactly models fields on the finite element mesh boundary and in the exterior region. By decoupling the interior finite element and exterior integral equation meshes, considerable flexibility is found in both the number of field expansion points as well as their density. Only the nonmetal portions of the object need be modeled using a finite element expansion; exterior perfect conducting surfaces are modeled using an integral equation with a single unknown field since E(tan) is identically zero on these surfaces. Numerical convergence, accuracy, and stability at interior resonant frequencies are studied in detail.

Cwik, Tom↗

NASA NTRS1972

An investigation into some problems in analytical processing of lunar orbiter photography

Problems in analytical processing of lunar orbiter photography are discussed. The effects of image motion and image motion compensation on the location of the principal point are analyzed. The effect of the focal plane shutter on the distortion and interior geometry is examined. Real data is used to confirm the workability of a mathematical model and the use of a computer to calibrate spaceborne photographic imagery.

Ghosh, S. K.↗

NASA NTRS1985

Vibrations and structureborne noise in space station

Theoretical models were developed capable of predicting structural response and noise transmission to random point mechanical loads. Fiber reinforced composite and aluminum materials were considered. Cylindrical shells and circular plates were taken as typical representatives of structural components for space station habitability modules. Analytical formulations include double wall and single wall constructions. Pressurized and unpressurized models were considered. Parametric studies were conducted to determine the effect on structural response and noise transmission due to fiber orientation, point load location, damping in the core and the main load carrying structure, pressurization, interior acoustic absorption, etc. These analytical models could serve as preliminary tools for assessing noise related problems, for space station applications.

Vaicaitis, R.↗

NASA NTRS2007

Antenna for Measuring Electric Fields Within the Inner Heliosphere

A document discusses concepts for the design of an antenna to be deployed from a spacecraft for measuring the ambient electric field associated with plasma waves at a location within 3 solar radii from the solar photosphere. The antenna must be long enough to extend beyond the photoelectron and plasma sheaths of the spacecraft (expected to be of the order of meters thick) and to enable measurements at frequencies from 20 Hz to 10 MHz without contamination by spacecraft electric-field noise. The antenna must, therefore, extend beyond the thermal protection system (TPS) of the main body of the spacecraft and must withstand solar heating to a temperature as high as 2,000 C while not conducting excessive heat to the interior of the spacecraft. The TPS would be conical and its axis would be pointed toward the Sun. The antenna would include monopole halves of dipoles that would be deployed from within the shadow of the TPS. The outer potion of each monopole would be composed of a carbon-carbon (C-C) composite surface exposed to direct sunlight (hot side) and a C-C side in shadow (cold side) with yttria-stabilized zirconia spacers in-between. The hot side cannot view the spacecraft bus, while the cold side can. The booms also can be tilted to minimize heat input to spacecraft bus. This design allows one to reduce heat input to the spacecraft bus to acceptable levels.

Sittler, Edward Charles↗