Search NASA⌕ Search

SEARCH · Search NASA

Results for “lattice strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

($\mathrm{INVITED}$)Counter-ion effect on the diffusion behavior of $\mathrm{Y}$b, $\mathrm{L}$u, and $\mathrm{N}$d ions in $\mathrm{YAG}$ transparent ceramics

The ability to fabricate additively manufactured laser waveguides with sharp dopant concentration interfaces is limited by diffusion of the dopants at the temperatures required to fully densify the material. Compositional analysis of bilayer samples, where each layer was either undoped YAG or YAG doped with Yb, Lu, or Nd, were fabricated such that all combinations were available for testing. Samples were fabricated at both 1750°C and 1850°C to determine the diffusion behavior of each dopant alone and also in the presence of a second dopant. It was found that the experimental concentration profiles exhibited both intragranular (bulk) and grain boundary contributions, and thus fitting to a complementary error function equation required the use of two diffusion coefficients. Nd always diffused further along grain boundaries than the other dopants, due in part to its small segregation coefficient in YAG. It is shown that the presence of Nd as a counter dopant inhibits intragranular diffusion of other dopants while enhancing their grain boundary diffusion. All the observed trends were attributed to a combination of intragranular lattice strain due to: dopant ions replacing yttrium substitutionally, the relative driving forces for the segregation of dopant ions to grain boundaries, and the ability of one dopant to affect the diffusion of a different dopant in the other direction to maintain charge neutrality.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Robustness of magnetocrystalline anisotropy and coercivity in Fe–Co–B

As a potential candidate for critical chemical element free permanent magnet, (Fe 0.7 Co 0.3 ) 2 B, shows promising intrinsic magnetic properties, including large magnetization, high Curie temperature and moderate magnetocrystalline anisotropy (MCA). Still, the coercivity that has been achieved is relatively low. To understand and improve coercivity, here we study the robustness of MCA related to the fluctuation of chemical composition and the structural distortion and its effect on coercivity in (Fe 0.7 Co 0.3 ) 2 B from first principles DFT (density functional theory) calculation and micromagnetic simulation. A fluctuation of cobalt content of 10%, or 1% isotropic lattice strain, or 2% tetragonal distortion reduces MCA energy up to 30%. By considering randomly distributed local MCA energy reduction up to 30%, the calculated coercivity of anisotropic bulk magnets reduced from 3.6 kOe to 2.2 kOe. Rational microstructure design, such as grain size refinement and development of strong crystal texture of MCA easy-axis (i.e., degree of alignment for (Fe 0.7 Co 0.3 ) 2 B grains), can enhance coercivity and mitigate the effect of local MCA reduction. In addition to acceptable intrinsic magnetic properties, the promising hard magnetic phase needs good MCA robustness to facilitate the development of practical magnets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Salt-Mediated Coarsening in Conversion-Reaction-Synthesized Nanoporous Metals and Nanocomposites Resolved through In Situ Synchrotron Diffraction Studies

High-energy synchrotron X-rays were used to probe the structural and microstructural evolution in Fe, Co, and Cu nanoporous metals (NPMs) and metal/salt nanocomposites (NCs) produced by recently developed conversion reaction synthesis (CRS) methods. Microstructure analysis of as-synthesized samples via whole pattern fitting showed that the NPMs exhibit domain sizes that increase as Co < Fe < Cu, with both Fe and Co having crystallite sizes below 3.0 nm. The as-synthesized metal/salt NCs had similar metal sizes, and additionally, the salt in the composite had unusually large lattice microstrain whose origin is attributed to chemical substitution of metal ions into the salt (e.g., Li $1–3x$ Fe $x$ Cl for Fe 3+ ). When thermal annealing is used to modify crystallite size, pore collapse often occurs in NPMs but NCs can be effectively tuned without this problem. While the NC coarsening occurs slowly at low temperatures, it was found that there is a drastic acceleration of the reaction rate at a specific onset temperature that results in the crystallite size increasing by an order of magnitude in about a minute. Curiously, there was no evidence in the diffraction data for salt melting at this onset temperature. However, there was a sharp reduction in the salt chemical lattice strain at the onset temperature, indicating that rapid metal coarsening is facilitated by the salt. Importantly, this behavior indicates an unexpectedly coupled reaction mechanism by which the metal ions needed for grain growth are supplied by the salt in a rate-limiting fashion.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2026

Structure-Dependent Lithium Metal Reactivity of Lithium Lanthanum Titanium Oxide Solid Electrolytes

Ongoing efforts to design stable, ionically conductive solid-state electrolytes (SSEs) for next-generation solid-state batteries make it clear that both long and short-range structural order strongly influence materials performance. However, clear structure-property relationships are generally lacking, making it difficult to develop design rules for improving the (electro) chemical stability of SSEs. Here, in this work, we synthesize epitaxial, single-crystal lithium lanthanum titanium oxide (LLTO) films and demonstrate that the kinetics of Ti 4+ reduction and lithium intercalation depend sensitively on the crystal orientation, with electrochemical stability increasing as LLTO (001) < (110) similar to (112) < (100). However, thermodynamic stability is ultimately unaffected-all orientations fully reduce after extended contact with Li metal. In contrast, amorphous LLTO films exhibit minimal, self-limiting reactivity that results in an interface that is stable to extended contact with Li metal. The results demonstrate the potential to engineer crystal lattice strain and long-range order to differentially tune the stability of the solid electrolyte toward reactive lithium metal and cathode materials, suggesting strategies for enabling the wider deployment of LLTO and other ionically conductive ceramic films in advanced energy storage technologies

Ketter, Benjamin [Argonne National Laboratory (ANL↗
DOE OSTI2023

Crystallographic Study of Product Phases of Carbothermic Reduction and Nitridation of Hafnium Dioxide

Details of the carbothermic reduction/nitridation to synthesize hafnium nitride (HfN) and hafnium carbide (HfC) are scarce in the literature. Therefore, this current study was carried out to evaluate two pathways for synthesizing these two refractory materials: direct nitridation and carbothermic reduction/nitridation. Two mixtures of hafnium dioxide and carbon with C/HfO 2 molar ratios of 2.15 and 3.1 were nitridized directly using flowing nitrogen gas at elevated temperatures (1300–1700 °C). The 3.1 C/HfO 2 molar ratio mixture was also carbothermically reduced under flowing argon gas to synthesize HfC, which was converted into HfN by introducing a nitridation step under both N 2(g ) and N 2(g) -10% H 2(g) . X-ray diffraction results showed the formation of HfN at 1300 and 1400 °C and HfC 1–y N y at ≥1400 °C under direct nitridation of samples using a C/HfO 2 molar ratio of 2.15. These phase analysis data together with lower lattice strain and greater crystallite sizes of HfC 1–y N y that formed at higher temperatures suggested that the HfC 1–y N y phase is preferred over HfN at those temperatures. Carbothermic reduction of 3.1 C/HfO 2 molar ratio samples under an inert atmosphere produced single-phased HfC with no significant levels of dissolved oxygen. In conclusion, carbothermic reduction nitridation made two phases of different carbon levels (HfC 1–y N y and HfC 1–y 'N y ', where y' < y), while direct nitridation produced a single HfC 1–y N y phase under both N 2 and N 2 -10% H 2 cover gas environments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Engineering of Exciton Spatial Distribution in CdS Nanoplatelets

Zinc-blende CdS nanoplatelets with atomically flat and very large {100} basal planes terminated solely by one type of element (either Cd or S atoms) are synthesized. Optical spectroscopy, X-ray diffraction, X-ray absorption, and transmission electron microscopy confirm that the surface structures of newly developed S-terminated CdS nanoplatelets are at least as well-defined as the original Cd-terminated nanoplatelets. Band gaps of the nanoplatelets are found to depend on not only the quantum-confined dimension (thickness) but also the nature of the surface termination. The facet structure dictates the packing of the ligands (carboxylate for Cd-terminated nanoplatelets and alkyl for S-terminated nanoplatelets), which causes a difference in the lattice strain and significantly affects the optical spectral width. Experimental and theoretical results reveal that engineering the exciton spatial distribution by the tailored synthesis of semiconductor nanocrystals with a precisely controlled surface structure is fully possible, which should open a new door for delivering the long-promised potential of semiconductor nanocrystals.

Cadmium sulfide↗
DOE OSTI2021

Antiphase-Boundary-Engineered Domain Switching in a (110)-Oriented BiFeO 3 Film

A ferroelectric domain wall memory device exploits the presence (or absence) of domain walls as the basis for information storage. Although structural defects strongly influence ferroelectric domain wall nucleation and growth, this correlation is far from being fully understood. For example, a single defect can play opposing roles: it can act as a nucleation site to initiate domain switching or, conversely, serve as a pinning center inhibiting domain wall motion. This is particularly the case for antiphase boundaries (APBs), whose influence on switching remains relatively unexplored despite being ubiquitous in oxide perovskite ferroelectrics. Here, we use aberration-corrected scanning transmission microscopy and in situ transmission electron microscopy under an applied bias to extensively characterize the influence of an APB on the switching behavior in a (110)-oriented BiFeO 3 thin film. We demonstrate that deterministic nucleation occurs in the proximity of a vertically oriented APB, following which domain growth occurs laterally in a symmetric fashion. Atomic-scale structural analysis reveals that the shear operation vector for the APB is 1/2[110]; this half-unit-cell shift extends over a few nanometers, implying that the APB plane is inclined toward the imaging direction. The symmetric switching observation is attributed to local inhomogeneous lattice strain and a reduction of polarization caused by the APB. These results demonstrate that an extended structural defect can be used as an active switching element rather than a stumbling block in reprogrammable domain-wall-based devices. Ultimately, this will expand the capabilities of ferroelectric thin films for future electronic devices based on ferroelectric domain walls.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Nitrogen-Doped PtNi Catalysts on Polybenzimidazole-Functionalized Carbon Support for the Oxygen Reduction Reaction in Polymer Electrolyte Membrane Fuel Cells

PtM (M = 3d transition metals) alloys are known as the promising oxygen reduction reaction catalysts and have been considered as the replacement of pure Pt catalysts for the commercialization of proton exchange membrane fuel cells. Although great progress has been made in the past three decades, the performance and durability of PtM catalysts still face stringent challenges from practical applications. Functionalization of a catalyst carbon support with nitrogen-contained groups can add charges onto its surface, which can be utilized to build a more complete ionomer/catalyst interface, to reduce the catalyst particle size, and to improve particle size distribution. Nitriding of PtNi catalysts can effectively improve the catalyst activity and stability by the modification of lattice strain. Hereby, we propose a synergistic approach of combining polybenzimidazole-grafted Vulcan XC72 carbon as the catalyst carbon support and the nitriding of PtNi to develop PtNiN/XC72-polybenzimidazole catalysts. Such PtNiN/XC72-PBI catalysts exhibit the excellent performance of fuel cell membrane electrode assembly (i.e., mass activity, 440 mA mgPt –1 ; electrochemical surface area, 51 m 2 gPt –1 ; and rated power density, 836 mW cm –2 ) as well as promising catalyst stability. The developed PtNiN/XC72-PBI meets the US DOE 2020 targets of mass activity for the fuel cell catalysts. This work provides a novel approach and a promising pathway on the development of the catalyst using such a synergistic approach-modification of the catalyst structure by nitrogen doping and functionalization of carbon support by polybenzimidazole for both high performance and high durability.

25 ENERGY STORAGE↗
DOE OSTI2023

An Innovative Insight into Performance Degradation of NCM111 Cathode Induced by Suspension of Operation

The lifespan of lithium-ion batteries varies enormously from fundamental study to practical applications. This big difference has been typically ascribed to the high degree of uncertainty in unpredictable and complicated operation conditions in real-life applications. Here, in this paper, we report that the pause of the charging–discharging process, which is frequently operated in practice but rarely studied in academics, is an important reason for the performance degradation of the NCM111 cathode. It is found that the pause during cycling could trigger a remarkable drop in capacity, giving rise to ~30% more capacity decay compared with the continuously cycled sample. In situ synchrotron X-ray diffraction analysis reveals that the harmful H1–H2 phase transition, which typically appears in the initial cycle but disappears in subsequent cycles, is reactivated by the pausing process. The anisotropic lattice strains that occur during the H1–H2 transition result in mechanical fractures that terminate with an inert NiO-type rock-salt phase on the surface of particles. The present study indicates that the discontinuous usage of rechargeable batteries is also a key factor for cycle life, which might provide a distinct perspective on the performance decay in practical applications.

25 ENERGY STORAGE↗
DOE OSTI2022

High Throughput Data-Driven Design of Laser-Crystallized 2D MoS 2 Chemical Sensors: A Demonstration for NO 2 Detection

High throughput characterization and processing techniques are becoming increasingly necessary to navigate multivariable, data-driven design challenges for sensors and electronic devices. For two-dimensional materials, device performance is highly dependent upon a vast array of material properties including the number of layers, lattice strain, carrier concentration, defect density, and grain structure. In this work, laser crystallization was used to locally pattern and transform hundreds of regions of amorphous MoS 2 thin films into 2D 2H-MoS 2 . Here a high throughput Raman spectroscopy approach was subsequently used to assess the process-dependent structural and compositional variations for each illuminated region, yielding over 6000 distinct nonresonant, resonant, and polarized Raman spectra. The rapid generation of a comprehensive library of structural and compositional data elucidated important trends between structure–property processing relationships involving laser-crystallized MoS 2 , including the relationships between grain size, grain orientation, and intrinsic strain. Moreover, extensive analysis of structure/property relationships allowed for intelligent design and evaluation of major contributions to device performance in MoS 2 chemical sensors. In particular, it is found that NO 2 sensor performance is strongly dependent on the orientation of the MoS 2 grains relative to the crystal plane.

36 MATERIALS SCIENCE↗
DOE OSTI2024

CeO2 Nanoparticle Doping as a Probe of Active Site Speciation in the Catalytic Hydrolysis of Organophosphates

Organophosphate hydrolysis is important for degrading environmentally harmful compounds and recovering phosphate ions in biological molecules. CeO2 nanocrystals have been well-studied for dephosphorylation via hydrolysis owing to the accessible and tunable distribution of Ce3+ and Ce4+ ions. However, there remains uncertainty in the literature regarding which surface defect properties direct catalytic activity, such as the Ce3+/Ce4+ distribution, oxygen vacancies, faceting, and dopants, and to what degree they contribute to efficient hydrolysis. Trivalent (M3+) dopants serve as a tool for manipulating defects, including the concentration of Ce3+ and oxygen vacancies, thereby influencing the hydrolytic activity of CeO2. Herein, trivalent metal ions (M = Y3+, Cr3+, In3+, and Gd3+) were employed to modulate the active sites on the CeO2 nanocrystal surface, and the effects of each metal dopant on the cerium oxide active sites for organophosphate hydrolysis were investigated. M-doped CeO2 nanoparticles were synthesized via hydrothermal methods, followed by annealing to remove ligands and prime the nanocrystal surface for catalysis. Catalytic performance was evaluated using dimethyl-p¬-nitrophenyl phosphate (DMNP) as a model organophosphate substrate, with degradation monitored over time using UV-visible absorption spectroscopy. Powder X-ray diffraction (PXRD), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy revealed successful doping of CeO2 in all cases, albeit with distinctive characteristics demonstrating how M3+ dopants affect catalysis. We show that CeO2 exhibits high sensitivity to dopants that generate lattice strain, Ce3+ ions, and oxygen vacancy defects. Consequently, achieving high catalytic efficiency within CeO2 requires a balanced active site ensemble, wherein defects are maintained at optimal concentrations and distributions on the nanocrystal surface.

Miura-Stempel, Emily L.↗
DOE OSTI2020

FA x Cs 1–x PbI 3 Nanocrystals: Tuning Crystal Symmetry by A-Site Cation Composition

Nanoscale semiconductors show remarkably tunable properties. For metal halide perovskite (MHP) nanocrystals (NCs), surface energy and lattice strain stabilize desirable MHP compositions and crystallographic phases that are unstable in the bulk. We report an X-ray scattering study of the average room-temperature crystal structure of ~15 nm FA x Cs 1–x PbI 3 (FA = formamidinium) NCs. All compositions crystallize in the perovskite structure; however, the average structure lowers in symmetry from the a (cubic) to ß (tetragonal) to γ (orthorhombic) perovskite phases with decreasing x (Cs addition). The corresponding a- to ß- and ß- to γ-phase transitions occur between x = 0.75–0.5 and x = 0.25–0.1, respectively. Furthermore, structural refinements also indicate large octahedral tilt angles (10–30°) in the ß- and γ-phases and an increase in (pseudo)cubic unit cell volume upon FA addition. This work establishes the composition–structure relationship for FA x Cs 1–x PbI 3 NCs and demonstrates the ability to target average crystal symmetry with facile synthetic control.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Formation of Coherent 1H–1T Heterostructures in Single-Layer MoS 2 on Au(111)

Heterojunctions of semiconductors and metals are the fundamental building blocks of modern electronics. Coherent heterostructures between dissimilar materials can be achieved by composition, doping, or heteroepitaxy of chemically different elements. Here, we report the formation of coherent single-layer 1H–1T MoS 2 heterostructures by mechanical exfoliation on Au(111), which are chemically homogeneous with matched lattices but show electronically distinct semiconducting (1H phase) and metallic (1T phase) character, with the formation of these heterojunctions attributed to a combination of lattice strain and charge transfer. The exfoliation approach employed is free of tape residues usually found in many exfoliation methods and yields single-layer MoS 2 with millimeter (mm) size on the Au surface. Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), scanning tunneling microscopy (STM), and scanning tunneling spectroscopy (STS) have collectively been employed to elucidate the structural and electronic properties of MoS 2 monolayers on Au substrates. Bubbles in the MoS 2 formed by the trapping of ambient adsorbates beneath the single layer during deposition, have also been observed and characterized. Lastly, our work here provides a basis to produce two-dimensional heterostructures which represent potential candidates for future electronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Size-Dependent Optical Band Gaps in Metal–Organic Framework Nanoparticles

Decades of research into size-dependent semiconductor optical gaps have focused on quantum confinement as the dominant mechanism. Emerging reports indicate that lattice strain─intentional or incidental─can impart optical shifts similar or greater in magnitude. Here, we report evidence of optical absorption and photoluminescence spectra of M(1,2,3-triazolate)2 (M = Mg, Cr, Mn, Fe, Co, Cu, Zn, or Cd) nanoparticles that blueshift from bulk values with decreasing particle sizes in a manner that defies explanation by conventional quantum confinement. Here, the phenomenon persists for particle sizes as large as 200 nm, whereas quantum confinement generally ceases beyond 20–30 nm diameters and follows a weaker dependence on the particle radius. Computational simulations and crystallographic analysis suggest that this behavior arises from size-dependent changes to metal–linker bonding that manifest in strain values comparable to literature reports of strain-induced optical shifts in other classes of materials. This behavior appears beyond this family of materials in other notable examples of metal–organic frameworks (MOFs), including the well-studied Cu3(trimesate)2 (CuBTC), where smaller sizes correlate with blueshifted optical gaps. Taken together, these results represent one of the few examples of size-dependent strain in crystalline materials and reinforce the emerging view that MOFs become softer materials when isolated as nanoparticles.

Electrical conductivity↗
DOE OSTI2026

Multimodal Nanoscale Mapping of Local Structure and CO 2 Adsorption in Metal–Organic Frameworks

Diamine functionalization of the metal−organic framework Mg 2 (dobpdc) (dobpdc 4− = 4,4′-dioxidobiphenyl-3,3′-dicarboxylate) significantly enhances its selectivity for CO 2 capture from flue gases and air. The structure and CO 2 capacity of such materials are typically assessed using bulk techniques that rely on averaging signal over large ensembles of unit cells, obscuring local heterogeneities, such as variations in CO 2 occupancy across individual nanocrystals. To resolve this limitation, we demonstrate a multimodal, nanoscale characterization of Mg 2 (dobpdc) appended with 1,3-diaminopropane. By employing recently developed characterization techniques at progressively smaller length scales, we uncover insights from correspondingly smaller populations of unit cells. First, we use parallel-beam 3D electron diffraction (3D ED) to identify a prominent expansion in lattice parameters upon desorption of CO 2 , as observed at the level of single nanocrystals. Second, we use convergent-probe 4D scanning transmission electron microscopy (4D-STEM) to quantify associated differences in lattice strain as a function of gas loading and diamine appending. These measurements sample small subvolumes within individual nanocrystals. Finally, we apply infrared scattering scanning near-field optical microscopy (IR s- SNOM) to confirm variable CO 2 chemisorption across adsorption sites at the surface of single nanocrystals. This multimodal, multiscale approach allows us to map heterogeneity within individual nanocrystals. Collectively, these findings emphasize the importance of local, nanoscale characterization of metal−organic frameworks in revealing previously unresolvable features that impact their performance.

Karstens, Sarah L. [University of California, Berk↗
DOE OSTI2021

Revealing nano-scale lattice distortions in implanted material with 3D Bragg ptychography

Small ion-irradiation-induced defects can dramatically alter material properties and speed up degradation. Unfortunately, most of the defects irradiation creates are below the visibility limit of state-of-the-art microscopy. As such, our understanding of their impact is largely based on simulations with major unknowns. Here we present an x-ray crystalline microscopy approach, able to image with high sensitivity, nano-scale 3D resolution and extended field of view, the lattice strains and tilts in crystalline materials. Using this enhanced Bragg ptychography tool, we study the damage helium-ion-irradiation produces in tungsten, revealing a series of crystalline details in the 3D sample. Our results lead to the conclusions that few-atom-large ‘invisible’ defects are likely isotropic in orientation and homogeneously distributed. A partially defect-denuded region is observed close to a grain boundary. These findings open up exciting perspectives for the modelling of irradiation damage and the detailed analysis of crystalline properties in complex materials.

42 ENGINEERING↗
DOE OSTI2022

Realization of unpinned two-dimensional dirac states in antimony atomic layers

Two-dimensional (2D) Dirac states with linear dispersion have been observed in graphene and on the surface of topological insulators. 2D Dirac states discovered so far are exclusively pinned at high-symmetry points of the Brillouin zone, for example, surface Dirac states at $\overline{Γ}$ in topological insulators Bi 2 Se(Te) 3 and Dirac cones at Κ and K' points in graphene. The low-energy dispersion of those Dirac states are isotropic due to the constraints of crystal symmetries. In this work, we report the observation of novel 2D Dirac states in antimony atomic layers with phosphorene structure. The Dirac states in the antimony films are located at generic momentum points. This unpinned nature enables versatile ways such as lattice strains to control the locations of the Dirac points in momentum space. In addition, dispersions around the unpinned Dirac points are highly anisotropic due to the reduced symmetry of generic momentum points. The exotic properties of unpinned Dirac states make antimony atomic layers a new type of 2D Dirac semimetals that are distinct from graphene.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Parasitic structure defect blights sustainability of cobalt-free single crystalline cathodes

Abstract Recent efforts to reduce battery costs and enhance sustainability have focused on eliminating Cobalt (Co) from cathode materials. While Co-free designs have shown notable success in polycrystalline cathodes, their impact on single crystalline (SC) cathodes remains less understood due to the significantly extended lithium diffusion pathways and the higher-temperature synthesis involved. Here, we reveal that removing Co from SC cathodes is structurally and electrochemically unfavorable, exhibiting unusual voltage fade behavior. Using multiscale diffraction and imaging techniques, we identify lithium-rich nanodomains (LRNDs) as a heterogeneous phase within the layered structure of Co-free SC cathodes. These LRNDs act as critical tipping points, inducing significant chemo-mechanical lattice strain and irreversible structural degradation, which exacerbates the voltage and capacity loss in electrochemical performance. Our findings highlight the considerable challenges of developing Co-free SC cathodes compared to polycrystalline ones and emphasize the need for new strategies to balance the interplay between cost, sustainability, and performance.

36 MATERIALS SCIENCE↗