Search NASA⌕ Search

SEARCH · Search NASA

Results for “lithiation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Redox oscillations in 18650-type lithium-ion cell revealed by in operando Compton scattering imaging

Compton scattering imaging using high-energy synchrotron x rays allows the visualization of the spatiotemporal lithiation state in lithium-ion batteries probed in operando. Here, we apply this imaging technique to the commercial 18650-type cylindrical lithium-ion battery. Our analysis of the line shapes of the Compton scattering spectra taken from different electrode layers reveals the emergence of inhomogeneous lithiation patterns during the charge-discharge cycles. Moreover, these patterns exhibit oscillations in time where the dominant period corresponds to the timescale of the charging curve.

42 ENGINEERING↗
DOE OSTI2026

Experimental considerations and applications for time-resolved impedance on silicon-anode battery systems

Dynamic electrochemical impedance spectroscopy (dEIS) utilizes a superimposed multi-sinusoidal waveform and enables temporally resolved investigations on various electrochemical processes; however, the signal-to-noise ratio must be maximized while retaining linearity and stationarity within the system. In the present work, we probe the impact of the waveform’s total amplitude as well as the waveform and phase profiles. The equal amplitude multi-sinusoidal waveform with 35 mV total amplitude (<1 mV per frequency) and random phase profile exhibits the lowest impedance noise. This input signal is sufficient in avoiding the high frequency signal attenuation from the potentiostat’s low-pass filter. Additionally, we demonstrate the optimized dEIS waveform’s utility in investigating surface passivation within thin-film and composite silicon (Si) anodes. Within a two-electrode Si-lithium metal coin cell, the charge transfer resistance (RCT) associated with alloying kinetics dominates the overall impedance. RCT increases with state of charge indicating a kinetic bottleneck at higher lithiation states. To explore this further, we utilize a three-electrode Si-LiNi0.8Mn0.1Co0.1O2 pouch cell to deconvolute the Si impedance contributions. The evolution of the solid electrolyte interphase (SEI) and charge transfer resistances correlate to specific Li–Si alloy phases. We attribute this to the influence of Si particle volume expansion on SEI instabilities and a kinetic bottleneck at higher lithiation states.

Lam, Steven [ORNL]↗
DOE OSTI2024

Operando pair distribution function analysis of nanocrystalline functional materials: the case of TiO 2 -bronze nanocrystals in Li-ion battery electrodes

Structural modelling of operando pair distribution function (PDF) data of complex functional materials can be highly challenging. To aid the understanding of complex operando PDF data, this article demonstrates a toolbox for PDF analysis. The tools include denoising using principal component analysis together with the structureMining , similarityMapping and nmfMapping apps available through the online service `PDF in the cloud' ( PDFitc , https://pdfitc.org/). The toolbox is used for both ex situ and operando PDF data for 3 nm TiO 2 -bronze nanocrystals, which function as the active electrode material in a Li-ion battery. The tools enable structural modelling of the ex situ and operando PDF data, revealing two pristine TiO 2 phases (bronze and anatase) and two lithiated Li x TiO 2 phases (lithiated versions of bronze and anatase), and the phase evolution during galvanostatic cycling is characterized.

Chemistry↗
DOE OSTI2020

In Operando XANES Imaging of High Capacity Intermetallic Anodes for Lithium Ion Batteries

In operando 2D X-ray absorption near edge structure (XANES) imaging was performed near the Cu K-edge during cycling of Cu 6 Sn 5 composite anodes for lithium ion batteries. Galvanostatic lithiation and delithiation with intermittent constant voltage holds near reaction plateaus show evolution of absorption spectra for active material particles. XANES spectra obtained from images taken during cycling were compared to standard spectra for Cu, Cu 6 Sn 5 , and Li 2 CuSn. Chemical composition was assessed for Cu-containing phases. Distinct Cu, Cu 6 Sn 5 , and Li 2 CuSn regions were identified for each voltage plateau. Mechanical degradation, electrode particle fracture and expansion were observed during delithiation. Furthermore, movement of particles during cycling suggests that expansion also impacts the supporting secondary phases and the transport networks therein. These results demonstrate that spectroscopic X-ray imaging methods can clearly distinguish chemically distinct phases in alloy electrodes and have the versatility to observe the evolution of these phases during lithiation and delithiation.

25 ENERGY STORAGE↗
DOE OSTI2020

Design Principles to Govern Electrode Fabrication for the Lithium Trivanadate Cathode

A full depth of discharge mathematical model for the lithium trivanadate cathode, considering lithiation of the layered α-phase, phase change, and lithiation of the rock-salt like β-phase at lower potentials, is developed. The coupled electrode-scale and crystal-scale model is fit to electrochemical data, and additionally validated with operando EDXRD. There is good agreement between the simulated and measured spatial variation of the volume fraction of the β-phase. This mathematical model is used to guide electrode fabrication, accounting for both ionic and electronic transport effects. Values of three design parameters—electrode thickness, porosity, and volume fraction of conductor—are identified, and the sensitivity of the energy density to these design parameters is quantified. The model is also used to investigate electrode design to create electrodes that deliver the maximum achievable energy density under the constraint that the α to β-phase transition is avoided, since phase change has been demonstrated to reduce cycle life. The energy density sacrificed to avoid phase change decreases at higher discharge rates, but the target values for electrode fabrication remain the same as those when optimizing the electrode for the full depth of discharge.

25 ENERGY STORAGE↗
DOE OSTI2021

Benefits of Fast Battery Formation in a Model System

Lithium-ion battery formation affects battery cost, energy density, and lifetime. An improved understanding of the first cycle of solid-electrolyte interphase (SEI) growth on carbonaceous negative electrodes could aid in the design of optimized formation protocols. In this work, we systematically study SEI growth during the formation of carbon black negative electrodes in a standard carbonate electrolyte. We show that the initial ethylene carbonate (EC) reduction reaction occurs at ~0.5-1.2 V during the first lithiation, except under fast lithiation rates (≥10C). The products of this EC reduction reaction do not passivate the electrode; only the SEI formed at lower potentials affects the second-cycle Coulombic efficiency. Thus, cycling quickly through the voltage regime of this reaction can decrease both formation time and first-cycle capacity loss, without an increase in subsequent-cycle capacity loss. We also show that the capacity consumed by this reaction is minimized at low temperatures and low salt concentrations. Finally, we discuss the mechanism behind our experimental results. This work reveals the fundamental processes underlying initial SEI growth on carbonaceous negative electrodes and provides insights for both optimizing the battery formation process and enabling novel electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2021

Potassium-Containing α-MnO 2 Nanotubes: The Impact of Hollow Regions on Electrochemistry

α-MnO 2 type materials have been studied as electrode materials in rechargeable batteries and electrocatalysts due to their 2 × 2 tunneled crystal structures capable of accommodating cations and their tunable physiochemical properties. In this study, we deliberately synthesized K + containing α-MnO 2 (K 0.9 Mn 8 O 16 ) hollow nanotubes varying the dimensions of the hollow regions and level of surface defects. The K 0.9 Mn 8 O 16 nanotube material samples have similar crystallinity, thermal stability, and average Mn oxidation state. Oxygen surface defects in the hollow regions were revealed through detailed studies using electron energy loss spectroscopy. The impact of the hollow regions and associated surface defects on the electrochemistry of K x Mn 8 O 16 were investigated using cyclic voltammetry, galvanostatic intermittent titration technique, and galvanostatic cycling. The K 0.9 Mn 8 O 16 nanotubes with a large hollow region (~30 nm) and higher level of surface defects show higher apparent lithium ion diffusion coefficients and lower polarization compared to the nanotubes with a small hollow region (~10 nm). In-situ lithiation demonstrated that the dimensions of the nanotube walls expanded, but the hollow region did not change in size as result of lithiation. Furthermore, this research demonstrates that tuning particle architecture and surface defects can positively impact functional behavior of electrochemical storage materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Pathways Toward High-energy Li-sulfur Batteries, Identified via Multi-reaction Chemical Modeling

Here we present a 1D model of a Li-Sulfur battery with physically derived geometric parameters and thermodynamically consistent electrochemical kinetics. The approach enables straightforward comparison of proposed Li-S mechanisms and provides insights into the influence of polysulfide intermediates on battery discharge. Comparing predictions from multiple mechanisms demonstrates the need for both lithiated and non-lithiated polysulfide species, and highlights the challenge of developing parameter estimates for complex electrochemical mechanisms. The model is also used to explore cathode design strategies. Discharge performance and polysulfide concentrations for electrolyte/sulfur ratios in the range 2–4 μ L mg −1 identifies trade-offs that limit battery energy and power density, and highlights the risk of polysulfide precipitation. New cathode and electrolyte approaches must limit polysulfide concentrations in the electrolyte, both to unlock better rate capabilities in Li-S technology and to prevent capacity fade due to polysulfide precipitation.

25 ENERGY STORAGE↗
DOE OSTI2023

Electrochemical Formation of Li-M-(M')-Si Phases Using Multivalent Electrolyte Salt Additives

Lithium-rich silicides (Li 15 Si 4 ), formed during the electrochemical lithiation of silicon, show high reactivity with electrolyte components that contribute to capacity decay, formal lithium loss, and low coulombic efficiency. Recently, the reactivity of lithium silicides was found to be suppressed by substituting a multivalent cation (i.e. Mg, Ca) for lithium that results in the room temperature formation of a ternary Li-M-Si phase. In this study, we explored a range of multivalent electrolyte salt additives (M = Ni, Cu, La, Ce, Sr, Ba, and Ca-Mg mixed salt) in a lithium-ion cell configuration and identified a room temperature electrochemical route to the formation of new ternary and quaternary lithium silicides. Using this method, both nickel and copper salts were found to plate onto the silicon electrode surface upon lithiation. Further, based on refined synchrotron XRD data, multivalent cations with an ionic radius similar to Na (~1.03 Å) or smaller can be inserted electrochemically into a formally cation-deficient Li 15 Si 4 host lattice to form new ternary (or quartenary) phases. The electrochemical synthesis of a new quaternary Li-M-M’-Si phase represents a facile route to preparing and scaling materials isostructural to the Heusler phase and electron-precise Li 14 MgSi 4 phase that results in enhanced cycling and calendar life performance.

25 ENERGY STORAGE↗
DOE OSTI2023

Trimer Quinoxalines as Organic Cathode Materials for Lithium-Ion Batteries

Due to synthetic ease, high redox potentials, low solubility in polar electrolytes, and good electric conductivity of their semiconducting crystals, discotic quinoxaline trimers (3Q) have been considered as possible candidates for 4 V organic cathodes in lithium-ion batteries. To assess their feasibility as such materials, several 3Q derivatives have been synthesized and tested in half-cells. In voltage limited cycling tests at 1.2–3.9 V vs Li/Li + , the specific discharge capacities of 40–180 mAh g -1 were obtained at a rate of 1 C, and multiple lithiation of 3Q and its derivatives was observed during discharge. However, the obtained discharge capacity was only a fraction of the theoretical capacity expected for reversible six-electron reduction; there was also rapid capacity fade. Our spectroscopic studies indicate the reversible three-electron lithiation at 2 V vs Li/Li + , but suggest instability of more highly discharged states. Finally, our conclusion is that while the 3Q derivatives combine several traits that are desirable in an organic cathode material (including negligible solubility, capacity for multiple charging, and near-100% coulombic efficiency), these materials are still impractical to use.

25 ENERGY STORAGE↗
DOE OSTI2021

Silicon Consortium Project: No-Go on Moir Interferometry for Measuring SEI Strain as a Probe for Calendar Life Testing

Silicon is a promising candidate as a next generation anode to replace or complement graphite electrodes due to its high energy density and low lithiation potential. When silicon is lithiated, it experiences over 300% expansion which stresses the silicon as well as its solid electrolyte interphase (SEI) leading to poor performance. The use of nano-sized silicon has helped to mitigate volume expansion and stress in the silicon, yet the silicon SEI is still both mechanically and chemically unstable. Identifying the mechanical failure mechanism of the SEI will help enhance calendar and cycle life performance through improved SEI design. In situ moiré interferometry was investigated to try and track the in-plane strain in the SEI and silicon electrode for this purpose. Moiré can detect on the order of 10 nm changes in displacement and is therefore a useful tool in the measurement of strain. As the sample undergoes small deformations, large changes in the moiré fringe allow for measurements of displacement below the diffraction limit of light. Figure 1a shows how the moiré fringe changes as the sample grating deforms. As the sample contracts or expands, the frequency of the moiré fringe changes, and this change is proportional to the strain in the sample.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Impact of lithium wall conditioning and wave-frequency on high density lower hybrid current drive experiment on EAST

A series of dedicated lower hybrid current drive (LHCD) experiments on EAST shows that lithium wall conditioning extends LH current drive and heating up to the line-averaged density of n ̅_e≈ 4x1019 m-3 for both 2.45 and 4.6 GHz. Current drive at such a high density is crucial for the development of long-pulse non-inductive scenarios on EAST. With lithiation, the LH power injection of 1.5 MW at 2.45 GHz resulted in a drop of loop voltage of ~ 0.3 V, which is a comparable loop voltage drop observed with 1.1 MW at 4.6 GHz. The observed decrease in loop voltage is attributed mostly to the RF heating effect. Another LHCD experiment suggests that lithium wall coating has a more significant impact on the scrape-off-layer (SOL) properties than changes in the Greenwald fraction. LHCD at 2.45 GHz still suffers from a loss of efficiency. Enhanced power ionization in front of the launcher may cause the onset of density-dependent wave instabilities. The rise in the midplane SOL density may also accelerate a transition in the divertor regime, leading to additional ionization and collisional losses in the X-point divertor plasma. Ray-tracing modeling supports that a lower wave frequency is more prone to collisional power loss. The experiments confirm that lithiation is a useful tool to control the SOL plasma, and suggest that density control in front of the launcher may be critical to mitigating power loss mechanisms in the plasma boundary.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Utilizing Conjugated Imine Polymers to Stabilize Nanoparticle Silicon Anodes

Silicon anodes provide a compelling route towards delivering high-capacity lithium-ion batteries, however they are notoriously difficult to stabilize in conventional liquid electrolytes that are compatible with high performance cathodes. Furthermore, the drastic changes in volume that occur as silicon is lithiated and delithiated can lead to rapid cell failure and novel polymeric binders are known to help mitigate mechanical issues. We have recently developed a novel method to synthesize the conjugated polymer phenylmethylimine (polyPMI) using an imine metathesis reaction. We have demonstrated that this polymer can be used to stabilize silicon nanoparticles to produce a composite lithium-ion battery anode that is electrochemically stable for hundreds of lithiation and delithiation cycles with a Coulombic efficiency that is greater than 99.95% in a traditional carbonate liquid electrolyte. This work covers the structure and properties of polyPMI within the context of the unique mechanical and electrochemical requirements of nanoparticle silicon anodes. The electrochemical behavior of this polymer also offers new opportunities as an organic lithium-coordinating material that can be used to stabilize a variety of other battery electrodes. More broadly, we posit that this solution-processed, ionically conductive, and electronically conductive polymer is applicable for a variety of energy storage and conversion technologies. Finally, this work demonstrates how this novel polymer chemistry provides additional opportunities for tuning electrode architecture to target high energy full cells.

conjugated polymers↗
DOE OSTI2024

Anode Upcycling via Tailored Solvent Treatment

To achieve a truly closed-loop direct recycling process for lithium-ion batteries, all component materials must be recovered. To date, direct recycling method development has primarily focused on the high-value transition-metal cathode materials, while the inherently lower-value graphite has been challenging to recover in a cost-effective manner. However, end-of-life graphite contains a unique engineered value due to the presence of the solid electrolyte interphase (SEI). Growth of the SEI during the cell's active lifetime stabilizes the electronically reactive graphite surface through an irreversible consumption of Li, and thus necessitates both excess lithiation of the cathode and a costly and time-intensive formation procedure during manufacturing. An optimized pre-formed SEI that capitalizes on existing SEI components from end-of-life batteries has the potential to significantly reduce cathode lithiation requirements and eliminate the critical bottleneck of formation cycling during cell remanufacturing. Further, retaining Li at the anode obviates the need for a separate Li leaching and recovery step, improving the overall efficiency of the direct recycling line. In this work, we present a novel approach to "upcycling" spent graphite through use of tailored chemical treatment to remove adverse (i.e., highly resistive and/or poorly passivating) SEI species while retaining beneficially passivating components. We have explored a rational set of solvents spanning a range of polarity, proticity, and molecular size to evaluate structure-property-performance relationships between applied solvent(s), removed and remaining SEI species, and electrochemical response of the resulting graphite product. Further, we have developed and optimized a robust and holistic analysis procedure that couples symmetric-cell electrochemical testing, multi-modal materials characterization, and advanced electrochemical modeling. These analysis results inform a set of correlative metrics for graphite performance relative to both solvent properties and upcycled SEI composition. We demonstrate effective tunability in the residual SEI composition by varying solvent identity and concentration, and report on several promising solvent systems that achieve comparable or performance to pristine graphite.

anode recycling↗
DOE OSTI2025

Mitigating Cyclable Li‐Ion Inventory Loss in Full Cells with Mn‐Rich Disordered Rocksalt Cathodes

Lithium (Li)- and manganese (Mn)-rich disordered rock salt (DRX) materials are promising cathode materials for next-generation Li-ion batteries. Although these cathode materials are Li-ions rich in their pristine state, their incorporation into full cells results in challenges with maintaining Li-ion inventory during cycling. Herein, the degradation mechanisms of DRX materials in different DRX||Graphite full cells are reported. It is found that DRX electrodes contain Li impurities, primarily due to the environmental sensitivity of mechanochemically synthesized DRX materials during sample transfer and storage. In addition, the structural instability of DRX triggers Mn dissolution. Dissolved Mn ions react with exposed Li x C y compounds and induce electrolyte decomposition on the anode, further depleting Li-ion inventory. Control experiments involving the pre-addition of Mn 2+ provide clear evidence of the impact of Mn dissolution on Li-ion inventory. The electrochemical activation process can stabilize DRX, alleviate Mn dissolution and thus mitigate the loss of Li-ion inventory. These mechanistic insights inform the development of chemical pre-lithiation and electrolyte additive strategies to collectively passivate interfaces, mitigate the effects of trace dissolved Mn ions, and preserve Li-ion inventory. Ultimately, the DRX||Graphite full cell achieves highly reversible electrochemical reactions with a high capacity retention. This study fills a research gap in DRX-based full cells and provides insights into degradation mechanisms and optimization strategies for their practical use.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Calcination Heterogeneity in Li-Rich Layered Oxides: A Systematic Study of Li 2 CO 3 Particle Size

Li- and Mn-rich (LMR) layered oxide positive-electrode materials exhibit high energy density and have earth-abundant compositions relative to conventional Ni-, Mn-, and Co-oxides (NMCs). The lithiation of coprecipitated precursors is a key part of the synthesis and offers opportunities for tuning the properties of LMR materials. Whereas the morphology of transition metal precursors has received substantial attention, that of Li sources has not. Using Li 1.14 Mn 0.57 Ni 0.29 O 2 as a model system, in this work, we establish a detailed understanding of LMR calcination pathways via in situ and ex situ diffraction, spectroscopy, microscopy, and thermogravimetry. Our work shows that a large Li 2 CO 3 particle size modulates a previously misunderstood thermogravimetric feature present at the Li 2 CO 3 melting point during layered oxide calcination and causes heterogeneity at larger length scales (inter-secondary particle) than previously reported (intra-secondary particle). We found that electrochemical performance is largely insensitive to this heterogeneity. Finally, this work highlights the sensitivity of layered oxide calcination pathways to synthesis conditions and suggests design rules to minimize calcination heterogeneity in layered oxides beyond LMR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Probing Clustering Dynamics between Silicon and PAA or LiPAA Slurries under Processing Conditions

This work explores the complex interplay between slurry aggregation, agglomeration, and conformation (i.e., shape) of poly(acrylic acid) (PAA)- and lithiated PAA-based silicon slurries as a function of the shear rate and the resulting slurry homogeneity. These values were measured by small-angle neutron scattering (SANS) and rheology-coupled ultra-SANS at conditions relevant to battery electrode casting. Different binder solution preparation methods, either a ball milling (BM) process or a planetary centrifugal mixing (PCM) process, dramatically modify the resulting polymer dynamics and organization around a silicon material. This is due to the different energy profiles of mixing where the more violent and higher energy PCM causes extensive breakdown and reformation of the binder, which is now likely in a branched conformation, while the lower energy BM results in simply lower-molecular weight linear polymers. In conclusion, the breakdown and reorganization of the polymer structure affect silicon slurry homogeneity, which affects subsequent electrode architecture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗