Search NASA⌕ Search

SEARCH · Search NASA

Results for “metal sintering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Size-Dependent Adsorption and Adhesion Energetics of Ag Nanoparticles on Graphene Films on Ni(111) by Calorimetry

Interest in the use of carbon supports for late transition metal nanoparticle catalysts has expanded rapidly due to the increasing importance of electrocatalysts for clean energy and environmental technologies and the use and storage of renewable electricity. Compared to oxide supports, almost nothing is known about the effect of metal nanoparticle size on the energies of the metal atoms within carbon-supported nanoparticles, yet these energies are crucial for understanding their surface reactivity and sintering kinetics. Here, the growth morphology and adsorption energetics of vapor-deposited Ag onto clean graphene/Ni(111) surfaces have been studied using a combination of single-crystal adsorption calorimetry (SCAC) and He + low-energy ion scattering (LEIS). The differential heat of Ag adsorption is 207 kJ/mol for making ~30 atom Ag particles on graphene terraces at 100 K and 16 kJ/mol higher for making ~9 atom Ag clusters at defect sites at the same temperature. The heat of adsorption increases rapidly with Ag coverage as 3D Ag nanoparticles nucleate and grow in size, asymptotically reaching within 5 kJ/mol of the bulk Ag sublimation enthalpy (285 kJ/mol) by 2 ML. The heats of adsorption and Ag nanoparticle densities from LEIS (~10 16 /m 2 ) were combined to provide the Ag/graphene adhesion energy (E adh = 1.8 J/m 2 in the large-particle limit) and the Ag chemical potential (μ) versus effective particle diameter (D). The Ag chemical potential was well-fitted by μ(D) = (3γ v /M – E adh )(1 + (1.5 nm)/D)(2V m /D), where γ v /M is the surface energy of bulk Ag and V m is its molar volume. The same equation is known to fit similar data for late transition metals on clean surfaces of metal oxide single crystals. The adhesion energy of Ag measured here on graphene falls within the wide range measured for Ag on those oxide surfaces and is almost as large as on the oxide that binds Ag particles most strongly, namely CeO 2 (111), which is well-known to be very effective at resisting catalyst deactivation by metal sintering. Furthermore, these results imply that carbon supports will be effective at resisting sintering and that Ag particles smaller than 6 nm on graphene will bind small adsorbed reaction intermediates more weakly than supports with weaker adhesion to Ag, like MgO(100).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Reduced-temperature sintering of spinel-type coatings and layers with metallic alloy powder precursors

A method of forming a spinel coating on a substrate is disclosed including the steps of coating at least a portion of the substrate with a precursor including an alloy powder, and sintering the precursor at a temperature of less than 1000 degrees Celsius to form the spinel coating. The alloy powder used for the precursor can include particles having a particle size of less than 10 micrometers. The method can be utilized to form spinel coatings as contact surfaces between electrodes and interconnects of solid oxide fuel cell (SOFC) stacks.

Zhu, Jiahong↗
NASA NTRS1954

Permeability and Strength Measurements on Sintered, Porous, Hollow Turbine Blades Made by the American Electro Metal Corporation under Office of Naval Research Contract N-ONR-295 (01)

An experimental investigation was made to determine the permeability and strength characteristics of a number of sintered, porous, hollow turbine rotor blades and to determine the effectiveness of the blade fabrication method on permeability control. The test blades were fabricated by the American Electro Metal Corporation under a contract with the Office of Naval Research, Department of the Navy, and were submitted to the NACA for testing. Of the 22 test blades submitted, ten were sintered but not coined, five were sintered and coined, and seven were sintered and not coined but contained perforated reinforcements integral with the blade shells. Representative samples of each group of blades were tested. Large variations in permeability in both chordwise and spanwise directions were found. Local deviations as large as 155 to -85 percent from prescribed values were found in chordwise permeability. Only one blade, an uncoined one, had a chordwise permeability variations which reasonably approached that specified. Even for this blade, local deviations exceeded 10 percent. Spanwise permeability, specified to be held constant, varied as much as 50 percent from root to tip for both an uncoined and a coined blade. Previous NACA analyses have shown that in order to maintain proper control of blade wall temperatures, permeability variations must not exceed plus or minus 10 percent. Satisfactory control of permeability in either the chordwise or the spanwise direction was not achieved in the blades tested. Spin tests made at room temperature for six blades revealed the highest material rupture strength to be 8926 pounds per square inch. This value is about one third the strength required for rotor blades in present-day turbojet engines. The lowest value of blade strength was 1436 pounds per square inch.

Richards, Hadley T.↗
NASA NTRS1987

Cast iron freezing mechanisms

This task focused on liquid phase sintering and infiltration studies of refractory metals and metal composites. Particular emphases was placed on those powered metal compacts which produce liquid alloys in sintering. For this class of materials, heating to a two phase region causes the constituent components to react, forming an alloy liquid which must wet the solid phase. Densification is initially driven by the free energy effects which cause rapid rearrangement. Further densification occurs by evaporation and condensation, surface diffusion, bulk flow, and volume diffusion.

Lillybeck, N. P.↗
DOE OSTI2020

Imaging of Calibrated Defects in Additively Manufactured Materials: Pulsed Thermal Tomography Nondestructive Examination of Additively Manufactured Reactor Materials and Components

Additive manufacturing (AM, or 3D printing) for commercial nuclear energy applications is an emerging method for cost-efficient manufacturing aimed at replacing aging nuclear reactor parts and reducing costs for new construction. Known material flaws in AM include low-density regions consisting of non-sintered powder, which have to be detected to ensure the safety of long-term performance nuclear reactor components. Currently, limited options are available for nondestructive evaluation (NDE), either during or post manufacturing. As a solution to NDE of AM, we are developing pulsed thermal imaging which is non-contact, one-sided, and scalable to arbitrary size and shape of the AM parts. Pulsed thermography (PT) system utilizes a high intensity flash lamp to rapidly heat surface of sample, and a high sensitivity fast-frame megapixel infrared (IR) camera to capture data of surface temperature variations. The acquired data cube consists of a stack of surface temperature images taken at different times. Information about material internal defects is extracted by analyzing the data cube. This report provides results of preliminary performance evaluation of pulsed thermal imaging capability in detection of imprinted flaws in AM metallic structures. The flaws were introduced into AM parts as imprinted hemispherical low density regions, consisting of trapped un-sintered metallic powder. Specimens for developed for this study consisted of AM stainless steel 316 and Inconel 718 plates. The diameters of imprinted defects varied from 1mm to 8mm, and their depths below the plate flat surface varied between 1mm and 6mm. Pulsed thermal tomography (PTT) processes the measured data cube to obtain 3D reconstructions of material effusivity using a unique inversion algorithm developed at Argonne. PTT has been previously used in imaging of similar size flat bottom hole (FBH) simulated defects in stainless steel 316 and Inconel 718 specimens. In the study involving AM specimens, PTT imaging results have shown that 1mm-diameter defects located 1mm and 2mm below the surface of specimens were detectable. Larger size defects were detectable at greater depth. We also explored an alternative approach to detection of material flaws in PT data cube, which is using neural learning-based approach to blind source separation. Detection of small material defects requires finding features in the data cube which have signal contrast levels approaching sensitivity limit of IR camera. In this study, an optimized Neural Learning based Blind Source Separation (NLBSS) algorithm, including Principal Component Analysis (PCA), and Independent Component Analysis (ICA) is demonstrated to automatically extract principal temporal and spatial features of thermography frames to enhance flaw detection. By using the NLBSS algorithm, material internal defects can be automatically detected. Furthermore, this processing approach compensates for experimental thermal imaging artifacts, such as noise and uneven heating. By merging artificial intelligence with phtotothermics, the NDE system detects internal calibrated defects of various sizes and depths in AM nuclear-grade metallic alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tuning transition metal nanoparticles on a non-traditional support via experimental design

The ability to control metal nanoparticle size and morphology on supported catalysts is crucial for optimizing catalytic performance in targeted applications. Here, this work presents a systematic approach for tuning Ni particle and crystallite size on an unconventional, low-porosity silica fume support through select thermal treatments. The catalyst was synthesized via the deposition of nickelocene onto silica fume, resulting in well-dispersed Ni nanoparticles. A face-centered central composite design was employed to systematically assess the effects of time, temperature, and sintering gas environment on metal particle growth. The results demonstrate that the sintering gas environment is the primary factor governing particle and crystallite evolution, with temperature as the next most significant influence. Nickel nanoparticles sintered at temperatures of 650 °C and above under inert conditions exhibited substantial growth and polycrystalline structures, whereas samples treated in oxidative environments formed NiO, restricting particle mobility. Minimally oxidative (500 ppm O₂) environments facilitated rapid sintering while effectively removing residual ligands from the one-step nickelocene deposition process. Extensive structural characterization via a combination of scanning transmission electron microscopy, X-ray diffraction, hydrogen temperature programmed reduction, and small-angle X-ray scattering revealed that oxidative treatments enhanced metal-support interactions, as evidenced by increased reduction temperatures and narrower particle size distributions. These findings establish quantitative relationships between sintering parameters and Ni nanoparticle characteristics, providing a framework for rational catalyst design through controlled thermal treatments. This methodology is broadly applicable to other catalytic systems and provides a quantitative foundation for catalyst design.

CVD↗
NASA NTRS2017

Nuclear Rocket Ceramic Metal Fuel Fabrication Using Tungsten Powder Coating and Spark Plasma Sintering

Nuclear thermal propulsion is an enabling technology for crewed Mars missions. An investigation was conducted to evaluate spark plasma sintering (SPS) as a method to produce tungsten-depleted uranium dioxide (W-dUO2) fuel material when employing fuel particles that were tungsten powder coated. Ceramic metal fuel wafers were produced from a blend of W-60vol% dUO2 powder that was sintered via SPS. The maximum sintering temperatures were varied from 1,600 to 1,850 C while applying a 50-MPa axial load. Wafers exhibited high density (>95% of theoretical) and a uniform microstructure (fuel particles uniformly dispersed throughout tungsten matrix).

Barnes, M. W.↗
DOE OSTI2021

Copper Electrode on Flexible Substrate by Intense Pulsed Light Sintering of Microsized Copper Particles

Metal electrodes deposited in a grid pattern onto flexible polymer substrates have been shown to be a viable alternative to replace indium tin oxide (ITO) as the transparent anode for organic photovoltaics. copper may be a better alternative in terms of cost and stability for large area low-cost solar modules, specifically on roll-to-roll platforms. These customized electrode patterns can be fabricated from copper nanoparticles through various printing techniques applicable to solution phase processing. The Intense Pulsed Light (IPL) technique has been used to sinter copper nanoparticles (~100nm) to fabricate conductive copper electrodes on flexible polymer substrates. However, compared to nanosized (~100 nm) copper particles, microsized (~2 um) copper is much cheaper. In this work, microsized (~2 um) copper is used to produce high conductive copper inks. The conductivity of the print can be adjusted through the use of surfactant. IPL sintering was optimized to obtain high conductivity copper films. In conclusion, several microscopic and electrical spectroscopic characterization techniques such as scanning electron microscopy (SEM), x-ray diffraction (XRD), 4-point probe resistivity measurements were employed to characterize the copper electrodes.

14 SOLAR ENERGY↗
NASA NTRS1993

The structural and electrical properties of low-resistance Ni contacts to InP

We have investigated the electrical and metallurgical behavior of the Ni-InP contact system. Specific contact resistivity (Rc) values in the low 10 exp -7 Omega-sq cm range are achieved with Ni-only contacts on n-InP by sintering at 400 C for several minutes. The postsinter contact metallization consists of three layers, arranged in the sequence: InP/Ni3P/Ni2P/In. Extended sintering (40 min) at 400 C brings about a rise in Rc to the 10 exp -4 Omega-sq cm range. After extended sintering, the contact metallization is found to consist of only two layers, arranged in the sequence: InP/Ni2P/In. Based on the correlation between low Rc and the presence of Ni3P at the metal-InP interface, it is suggested that the presence of Ni3P is the cause of the low Rc values. We show that the sintering schedule used to achieve low values of Rc is accompanied by substantial metal-InP interdiffusion that results in severe device degradation.

Fatemi, Navid S.↗
DOE OSTI2021

Growth, sintering, and chemical states of Co supported on reducible CeO 2 (111) thin films: The effects of the metal coverage and the nature of the support

The growth, sintering, and interaction of cobalt with ceria were studied under ultrahigh vacuum conditions by vapor-deposition of Co onto well-defined CeOx(111) (1.5 < x < 2) thin films grown on Ru(0001). Charge transfer from Co to ceria occurs upon deposition of Co on CeO 1.96 and partially reduced CeO 1.83 at 300 K. X-ray photoelectron spectroscopy studies show that Co is oxidized to Co 2+ species at the cost of the reduction of Ce 4+ to Ce 3+ , at a lesser extent on reduced ceria. Co 2+ is the predominant species on CeO 1.96 at low Co coverages (e.g., ≤0.20 ML). The ratio of metallic Co/Co 2+ increases with the increase in the Co coverage. However, both metallic Co and Co 2+ species are present on CeO 1.83 even at low Co coverages with metallic Co as the major species. Scanning tunneling microscopy results demonstrate that Co tends to wet the CeO 1.96 surface at very low Co coverages at room temperature forming one-atomic layer high structures of Co–O–Ce. The increase in the Co coverage can cause the particle growth into three-dimensional structures. The formation of slightly flatter Co particles was observed on reduced CeO 1.83 . In comparison with other transition metals including Ni, Rh, Pt, and Au, our studies demonstrate that Co on ceria exhibits a smaller particle size and higher thermal stability, likely arising from strong metal–support interactions. The formed particles upon Co deposition at 300 K are present on the ceria surface after heating to 1000 K. The Co–ceria interface can be tuned by varying the Co metal coverage, the annealing temperature, and the nature of the ceria surface.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Print-Consistency and Process-Interaction for Inkjet-Printed Copper on Flexible Substrate

Printed electronics is a fastest growing and emerging technology that have shown much potential in several industries including automotive, wearables, healthcare, and aerospace. Its applications can be found not only in flexible but also in large area electronics. The technology provides an effective and convenient method to additively deposit conductive and insulating materials on any type of substrate. Comparing with traditional manufacturing processes, which involves chemical etching, this technology also comes to be relatively environmental friendly. Despite its status, it is not without its challenges. Starting from the material being compatible in the printer equipment to the point of achieving fine resolutions, and with excellent properties are some of the challenges that printed electronics face. Among the myriad of printing technologies such as Aerosol Jet, micro-dispensing, gravure printing, screen printing, Inkjet printing, Inkjet has gained much attention due to its low-cost, low material consumption, and roll-to-roll capability for mass manufacturing. The technology has been widely used in home and office, but recently gained interest in printed electronics in a research and development setting. Conductive materials used in Inkjet printing generally comprises of metal Nanoparticles that need to be thermally sintered for it to be conductive. The preferred metal of choice has been mostly silver due to its excellent electrical properties and ease in sintering. However, silver comes to be expensive than its counterpart copper. Since copper is prone to oxidation, much focus has been given towards photonic sintering that involves sudden burst of pulsed light at certain energy to sinter the copper Nanoparticles. With this technique, only the printed material gets sintered in a matter of seconds without having a great impact on its substrate, due to which it is also preferred in low temperature applications. With all the knowledge, there is still a large gap in the process side with copper where it is important to look how the print process affects the resolution of the print along with the effect of post-print processes on electrical and mechanical properties. In this paper, a copper Inkjet ink is utilized for understanding the effect of Inkjet print parameters on the ejected droplet and its resolution. Post-print process is also quantified using a photonic sintering equipment for excellent electrical and mechanical properties. To demonstrate the complete process, commercial-off-the-shelf components will also be mounted on the additively printed pads via Inkjet. Statistically, control charting technique will be utilized to understand the capability of the Inkjet process.

printed electronics↗
DOE OSTI2023

Perovskite evolution on La modified Mn 1.5 Co 1.5 O 4 spinel through thermal ageing with enhanced oxidation activity: Is sintering always an issue?

Non-precious metal oxides have great potential in catalytic deep oxidation of emitted hydrocarbons to help address various environmental pollution concerns. However, sintering issue is a stumbling block in practical application upon long-term high-temperature operation or thermal shock experience. Herein, La was applied to modify Mn 1.5 Co 1.5 O 4 spinel to get a highly active oxidation catalyst with exceptional stability against high-temperature thermal ageing treatment. With thermal ageing at 750 °C for 100 h, the La modified Mn–Co composite reached 90 % conversion in toluene oxidation at 265 °C under the high WHSV of 120,000 mL g -1 h -1 , while this value increased to 312 °C over blank Mn–Co spinel. The addition of La not only inhibited the growth of spinel nanocrystals, but also brought about perovskite formation through sintering, generating perovskite-spinel interfaces, thus enhancing both activity and stability. Meanwhile, the La modified Mn–Co spinel exhibited superior performance in presence of water or sulfur dioxide after thermal ageing treatment. In conclusion, this work offers a versatile strategy to design anti-sintering and active oxidation nanocatalysts based on non-precious metal oxides for industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A Perspective on Thin-Film Perovskites as Supports for Metal Catalysts

Perovskite-supported metals have sometimes been referred to as “intelligent catalysts” because of the potential to regenerate sintered particles by driving the metal into the oxide lattice by high-temperature oxidation and releasing the metal by reduction. However, low surface areas and incomplete release of metal from the lattice have prevented the widespread application of these materials. Furthermore, we describe the preparation of thin perovskite films on stable supports by Atomic Layer Deposition (ALD) as a means for avoiding the limitations associated with bulk perovskites. Examples will be given that demonstrate many of the favorable properties of perovskite supports can be retained, while avoiding some of the shortcomings. Potential opportunities for using these materials are discussed.

36 MATERIALS SCIENCE↗
NASA NTRS2019

Optimization of Aluminum-Tin Ink Composition and Sintering in Atmospheric Conditions

This study will focus on the basics of generating an aluminum-tin ink that can sinter in air and exhibits properties near that of a solid aluminum-tin alloy. Sintering temperatures will also be assessed in this study. Once the optimal aluminum ink composition is determined, the optimal ink thickness for homogeneous sintering must be determined by additional experimentation. Additive manufacturing is a rapidly developing and growing manufacturing process and has proven successful in many different ways. Processes, such as extrusion three-dimensional (3D) printing and selective laser melting (SLM), have proven to work but have limitations, such as material capabilities or density issues. SLM is a revolutionary process for additive manufacturing of metals but cannot be used in outer space due to the need for metallic powder which would diffuse into the atmosphere in a zero-gravity environment. For this reason, metallic ink additive manufacturing is a potential solution. Work is being done on metallic ink additive manufacturing in a vacuum for electrical applications. This project has focused on developing an aluminum-tin metallic ink that can sinter without the need of a vacuum or inert gas-purged atmosphere in order to prevent oxidation of the aluminum by adding flux. Once a potential ink composition has been determined through sintering of small disks and thin layers of ink, the ink may be studied with a multimaterial 3D printer at NASA Marshall Space Flight Center (MSFC) in future experiments. If successful, this aluminum-tin ink will be capable for use on the International Space Station to make replacement parts quickly. Along with its zero-gravity advantages, this ink may also have applications on Earth because it may be extruded on a substrate with precise ceramic tips in a 3D printing process. This would allow the fabrication of precise, complex shapes and may generate a much faster and more efficient printing process as compared with traditional powder bed additive manufacturing processes. The process would not be limited by a small building volume because the system would not require an enclosed chamber.

Courtright, Z. S.↗
NASA NTRS1992

Combustion synthesis of ceramic-metal composite materials - The TiC-Al2O3-Al system

Combustion synthesis was applied for producing ceramic-metal composites with reduced levels of porosity, by allowing an excess amount of liquid metal, generated by the exothermic reaction during synthesis, to infiltrate the pores. It is shown that this method, when applied to TiC-Al2O3 system, led to a decreased level of porosity in the resulting TiC-Al2O3-Al product, as compared with that of TiC-Al2O3 system. This in situ procedure is more efficient than the two-stage conventional processes (i.e., sintering followed by liquid metal infiltration), although there are limitations with respect to total penetration of the liquid metal and maintaining a stable propagation of the combustion reaction.

Feng, H. J.↗
DOE OSTI2021

Compositions and methods for thermoelectric ceramics

In one aspect, the disclosure relates to thermoelectric ceramic oxide compositions comprising a CaMnO 3 ceramic. In a further aspect, the disclosed thermoelectric ceramic oxide compositions can dramatically increase the energy conversion efficiency of thermoelectric through a combination of modifying the chemistry of precursor materials, and simultaneously introducing a metal oxide liquid phase during sintering. In a further aspect, the present disclosure pertains to thermoelectric ceramic oxide compositions comprising a metal doped CaMnO 3 having with a metal oxide grain boundary phase; wherein the metal is selected from group 13, group 14, group 15, group 16, or a rare earth element. In a still further aspect, the disclosure relates to methods for making the thermoelectric ceramic oxide materials. This abstract is intended as a scanning tool for purposes of searching in the particular art and is not intended to be limiting of the present disclosure.

Song, Xueyan↗